Simultaneous morphological stability and high charge carrier mobilities in donor–acceptor block copolymer/PCBM blends

Donor–acceptor block copolymers (BCP), incorporating poly(3‐hexylthiophene) (P3HT), and a polystyrene copolymer with pendant fullerenes (PPCBM) provide desired stable nanostructures, but mostly do not exhibit balanced charge carrier mobilities. This work presents an elegant approach to match hole and electron transport in BCP by blending with molecular PCBM without causing any macrophase separation. An insufficient electron mobility of PPCBM can be widely compensated by adding PCBM which is monitored by the space‐charge limited current method. Using X‐ray diffraction, atomic force microscopy, and differential scanning calorimetry, we verify the large miscibility of the PPCBM:PCBM blend up to 60 wt % PCBM load forming an amorphous, molecularly mixed fullerene phase without crystallization. Thus, blending BCP with PCBM substantially enhances charge transport achieving an electron mobility of μ_e=(3.2 ± 1.7) × 10^?4 cm²V^?1s^?1 and hole mobility of μ_h=(1.8 ± 0.6) × 10^?3 cm²V^?1s^?1 in organic field‐effect transistors (OFET). The BCP:PCBM blend provides a similarly high ambipolar charge transport compared to the established P3HT:PCBM system, but with the advantage of an exceptionally stable morphology even for prolonged thermal annealing. This work demonstrates the feasibility of high charge transport and stable morphology simultaneously in a donor–acceptor BCP by a blend approach. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1125–1136     

Light-induced degradation of the active layer of polymer-based solar cells

Polymer-based organic solar cells are known to offer a poor stability in real use conditions, and the photodegradation of the active organic layer plays an important role in the reduced lifetime of the devices. This paper focuses on the photodegradation of two conjugated polymers used in organic solar cells, namely poly(2-methoxy-5-(3′,7′-dimethyloctyloxy)-1,4-phenylenevinylene (MDMO-PPV) and poly(3-hexyylthiophene) (P3HT), and their blends with [60]PCBM (methano-fullerene[6,6]-phenyl C61-butyric acid methyl ester), a fullerene derivative. MDMO-PPV and P3HT thin films were submitted to photoageing (λ > 300 nm) in the presence and in the absence of oxygen. The mechanisms by which these polymers degrade were elucidated. P3HT, pristine and blended with PCBM, was shown to be much more stable under illumination than MDMO-PPV. The results showed that, if deposited on an inert substrate and well protected from oxygen with a convenient encapsulation, P3HT:PCBM based active layer should be intrinsically stable for several years in use conditions.     

Synthesis and photovoltaic properties of a low‐band‐gap polymer consisting of alternating thiophene and benzothiadiazole derivatives for bulk‐heterojunction and dye‐sensitized solar cells

We synthesized a novel low‐band‐gap, conjugated polymer, poly[4,7‐bis(3′,3′‐diheptyl‐3,4‐propylenedioxythienyl)‐2,1,3‐benzothiadiazole] [poly(heptyl₄‐PTBT)], consisting of alternating electron‐rich, diheptyl‐substituted propylene dioxythiophene and electron‐deficient 2,1,3‐benzothiadiazole units, and its photovoltaic properties were investigated. A thin film of poly(heptyl₄‐PTBT) exhibited an optical band gap of 1.55 eV. A bulk‐heterojunction solar cell with indium tin oxide/poly(3,4‐ethylenedioxythiophene)/poly(heptyl₄‐PTBT): methanofullerene [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) (1:4)/LiF/Al was fabricated with poly(heptyl₄‐PTBT) as an electron donor and PCBM as an electron acceptor and showed an open‐circuit voltage, short‐circuit current density, and power conversion efficiency of 0.37 V, 3.15 mA/cm², and 0.35% under air mass 1.5 (AM1.5G) illumination (100 mW/cm²), respectively. A solid‐state, dye‐sensitized solar cell with a SnO₂:F/TiO₂/N3 dye/poly(heptyl₄‐PTBT)/Pt device was fabricated with poly(heptyl₄‐PTBT) as a hole‐transport material. This device exhibited a high power conversion efficiency of 3.1%, which is the highest power conversion efficiency value with hole‐transport materials in dye‐sensitized solar cells to date. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1394–1402, 2007     

Potential of bifluorenylidene derivatives as nonfullerene small-molecule acceptor for heterojunction organic photovoltaics: a density functional theory study

To maximize the efficiency of heterojunction organic photovoltaics (HJOPVs), it is imperative to increase not only the open-circuit voltage (V _OC) but also the short-circuit current (I _SC). Therefore, it is desirable to find an organic acceptor material that possesses a higher lowest unoccupied molecular orbital (LUMO) level for higher V _OC and can absorb photons in the solar spectrum efficiently for larger I _SC. In this paper, in comparison with the typical donor poly(3-hexylthiophene) (P3HT) and acceptor [6,6]-phenyl-C₆₁-butyric acid ester ([60]PCBM), the geometries, electronic structures, absorption spectra, and transport properties of a series of organic compounds containing 9,9′-bifluorenylidene (9,9′BF) were systematically investigated using density functional and the semiclassical Marcus charge transfer theory calculation to evaluate their potential severing as acceptor. Our results indicate that the absorption spectra of 99′BF derivatives have better overlap with the solar spectrum than those of [60]PCBM, and higher LUMOs result in a significant enhancement of V _OC when they are used in HJOPVs with P3HT as donor materials. On the other hand, these compounds own higher electron carrier mobilities comparing with [60]PCBM. The study also demonstrates that the H-shaped compounds based on the 99′BF backbone possess good photophysical and charge transport properties, can be promising organic semiconductor for heterojunction photovoltaics.     

Charge transport study of semiconducting polymers and their bulk heterojunction blends by capacitance measurements

We use frequency dependent capacitance measurements to probe carrier mobilities and transport parameters of six representative semiconducting polymers and some of their bulk heterojunction (BHJ) blends. With a suitable choice of a hole injection layer, well-defined signals for hole transport characterization can be obtained for the pristine polymers [J. Appl. Phys. 99, 013706 (2006)]. However, ill-defined signals with negative capacitances, arising from undesirable electron leakages, are obtained for the BHJ blends. The problem of electron leakage can be circumvented by inserting an electron blocking and trapping layer under the cathode. As a result, hole transport properties of BHJ blends can be obtained. For the BHJ of poly(3-hexylthiophene) blended with [6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PC₆₁BM), the hole mobilities seem to be insensitive to the composition of the BHJ, indicating the P3HT component in the BHJ is well connected. On the other hand, for poly[N-9“-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadia zole)] doped with [6,6]-phenyl-C71-butyric acid methyl ester (PCDTBT:PC₇₁BM), a clear reduction of the hole mobility is observed as the polymer composition is reduced. Temperature dependent experiments were performed. The data are analyzed by the Gaussian Disorder Model. We found that the energetic disorder is independent of the composition of the BHJ. Organic photovoltaic performances of BHJ blends are also measured in this contribution. The correlation between device performance and energetic disorder of the BHJ will be discussed. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Effect of multiple adduct fullerenes on charge generation and transport in photovoltaic blends with poly(3‐hexylthiophene‐2,5‐diyl)

The effect of replacing [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) by its multiadduct analogs (bis‐PCBM and tris‐PCBM) in bulk heterojunction organic solar cells with poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) is studied in terms of blend film microstructure, photophysics, electron transport properties, and device performance. Although the power conversion efficiency of the blend with bis‐PCBM is similar to the blend with PCBM, the performance of the devices with tris‐PCBM is considerably lower as a result of small photocurrent. Despite the lower electron affinity of the fullerene multiadducts, μs‐ms transient absorption measurements show that the charge generation efficiency is similar for all three fullerenes. The annealed blend films with multiadducts show a lower degree of fullerene aggregation and lower P3HT crystallinity than the annealed blend films with PCBM. We conclude that the reduction in performance is due largely to poorer electron transport in the blend films from higher adducts, due to the poorer fullerene network formation as well as the slower electron transport within the fullerene phase, confirmed here by field effect transistor measurements. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Water soluble amino grafted silicon nanoparticles and their use in polymer solar cells

Stable aqueous amino-grafted silicon nanoparticles(SiNPs-NH2) were prepared via one-pot solution method. By grafting amino groups on the particle surface, the dispersion of SiNPs in water became very stable and clear aqueous solutions could be obtained. By incorporating SiNPs-NH2 into the hole transport layer of poly(3,4-ethylenedioxythiophene)/polystyrene sulfonic acid(PEDOT:PSS), the performance of polymer solar cells composed of poly[2-methoxy,5-(2'-ethylhexyloxy)-1,4-phenylene vinylene](MEH-PPV):[6,6]-phenyl-C61-butyric acid methyl ester(PCBM) as active layer can be improved. SiNPs-NH2 are dispersed uniformly in the PEDOT:PSS solution and help form morphologies with small-sized domains in the PEDOT:PSS film. SiNPs-NH2 serve as screens between conducting polymer PEDOT and ionomer PSS to improve the phase separation and charge transport of the hole transport layer. As a result, the sheet resistance of PEDOT:PSS thin films is decreased from(93 ± 5) × 105 to(13 ± 3) × 105 ?/□. The power conversion efficiency(PCE) of polymer solar cells was thus improved by 9.8% for devices fabricated with PEDOT:PSS containing 1 wt% of SiNPs-NH2, compared with the devices fabricated by original PEDOT:PSS.     

Enhanced Hole Transport in Ternary Blend Polymer Solar Cells

Recently, ternary blend polymer solar cells have attracted great attention to improve a short-circuit current density (J_SC) effectively, because complementary absorption bands can harvest the solar light over a wide wavelength range from visible to near-IR region. Interestingly, some ternary blend solar cells have shown improvements not only in J_SC but also in fill factor (FF). Previously, we also reported that a ternary blend solar cell based on a low-bandgap polymer (PTB7-Th), a wide-bandgap polymer (PDCBT), and a fullerene derivative (PCBM) exhibited a higher FF than their binary analogues. Herein, we study charge transport in PTB7-Th/PDCBT/PCBM ternary blend films to address the origin of the improvement in FF. We found that hole polarons are located in PTB7-Th domains and their mobility is enhanced in the ternary blend film.     

Phase behavior of PCBM blends with different conjugated polymers

In this work the phase behavior of [6,6]-phenyl C(61)-butyric acid methyl ester (PCBM) blends with different poly(phenylene vinylene) (PPV) samples is investigated by means of standard and modulated temperature differential scanning calorimetry (DSC and MTDSC) and rapid heat-cool calorimetry (RHC). The PPV conjugated polymers include poly(2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylene vinylene) (MDMO-PPV), High T(g)-PPV which is a copolymer, and poly((2-methoxy-5-phenethoxy)-1,4-phenylene vinylene) (MPE-PPV). Comparisons of these PPV:PCBM blends with regioregular poly(3-hexyl thiophene) (P3HT):PCBM blends are made to see the different component miscibilities among different blends. The occurrence of liquid-liquid phase separation in the molten state of MDMO-PPV:PCBM and High T(g)-PPV:PCBM blends is indicated by the coexistence of double glass transitions for blends with a PCBM weight fraction of around 80 wt%. This is in contrast to the P3HT:PCBM blends where no phase separation is observed. Due to its high cooling rate (about 2000 K min(-1)), RHC proves to be a useful tool to investigate the phase separation in PPV:PCBM blends through the glass transition of these crystallizable blends. P3HT is found to have much higher thermal stability than the PPV samples.     

The role of alkane dithiols in controlling polymer crystallization in small band gap polymer:Fullerene solar cells

The effect of the addition of 1,8‐octanedithiol (ODT) during processing on the microstructure of blend films of poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7(2,1,3‐benzothiadiazole)] (PCPDTBT) and [6,6]‐phenyl‐C₇₁ butyric acid methyl ester ([70]PCBM) is studied. Grazing incidence X‐ray diffraction and absorption spectroscopy show that the crystalline order of PCPDTBT increases when ODT is introduced in the solution phase either to neat polymer systems or to blends with [70]PCBM. The increased crystalline order is accompanied by less dispersive hole transport in the polymer, and leads to a more efficient formation of a percolating fullerene network within the blend. This contributes to an increase in photocurrent generation. However, the bimolecular recombination rate as determined from photovoltage transients increases upon addition of ODT, limiting the power conversion efficiency to values well below those expected from the energy levels of PCPDTBT. We propose some explanations for this increase in bimolecular recombination, based also on variable angle spectroscopic ellipsometry measurements. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Tightly Bound Double‐Caged [60]Fullerene Derivatives with Enhanced Solubility: Structural Features and Application in Solar Cells

A series of novel highly soluble double‐caged [60]fullerene derivatives were prepared by means of lithium‐salt‐assisted [2+3] cycloaddition. The bispheric molecules feature rigid linking of the fullerene spheres through a four‐membered cycle and a pyrrolizidine bridge with an ester function CO₂R (R=n ‐decyl, n ‐octadecyl, benzyl, and n ‐butyl; compounds 1 a – d , respectively), as demonstrated by NMR spectroscopy and X‐ray diffraction. Cyclic voltammetry studies revealed three closely overlapping pairs of reversible peaks owing to consecutive one‐electron reductions of fullerene cages, as well as an irreversible oxidation peak attributed to abstraction of an electron from the nitrogen lone‐electron pair. Owing to charge delocalization over both carbon cages, compounds 1 a – d are characterized by upshifted energies of frontier molecular orbitals, a narrowed bandgap, and reduced electron‐transfer reorganization energy relative to pristine C₆₀. Neat thin films of the n ‐decyl compound 1 a demonstrated electron mobility of (1.3±0.4)×10⁻³ cm² V⁻¹ s⁻¹, which was comparable to phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and thus potentially advantageous for organic solar cells (OSC). Application of 1 in OSC allowed a twofold increase in the power conversion efficiencies of as‐cast poly(3‐hexylthiophene‐2,5‐diyl) (P3HT)/ 1 devices relative to the as‐cast P3HT/PCBM ones. This is attributed to the good solubility of 1 and their enhanced charge‐transport properties — both intramolecular, owing to tightly linked fullerene cages, and intermolecular, owing to the large number of close contacts between the neighboring double‐caged molecules. Test P3HT/ 1 OSCs demonstrated power‐conversion efficiencies up to 2.6 % ( 1 a ). Surprisingly low optimal content of double‐caged fullerene acceptor 1 in the photoactive layer (≈30 wt %) favored better light harvesting and carrier transport owing to the greater content of P3HT and its higher degree of crystallinity.     

Synthesis and Photovoltaic Properties of Ester Group Functionalized Polythiophene Derivatives

To increase the open circuit voltage (V_OC) of polymer solar cells (PSCs) based on polythiophene, two new ester group functionalized polythiophene derivatives, PCTDT and PCTBDT, were designed and synthesized via alternating copolymerization of thiophene‐3‐carboxylate (CT) with the 2,2′‐bithiophene (DT) and benzodithiophene (BDT) units, respectively. The resulting copolymers exhibited broad and strong absorptions in the visible region, which was similar to that of the commonly used poly(3‐hexylthiophene) (P3HT). Through cyclic voltammetry measurements, it was found that both copolymers showed lower HOMO energy levels (−5.27 eV for PCTDT and −5.36 eV for PCTBDT) than that of P3HT (−5.03 eV), indicating that the HOMO energy level could be efficiently reduced by introducing the ester group into the polymer side chain. Photovoltaic properties of the copolymers blended with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as electron acceptor were investigated. The obtained two devices possessed both relatively large short circuit current (I_SC) and higher V_OC than that of P3HT:PCBM blend. For PCTBDT:PCBM blend, a power conversion efficiency (PCE) up to 2.32%, an I_SC of 6.94 mA · cm⁻², and a V_OC of 0.80 V were observed while PCTDT:PCBM system demonstrated a PCE of 1.75% with a V_OC of 0.68 V.

     

基于稀土配合物的有机光盲型紫外探测器

使用二苯甲酰甲烷-二苯菲罗啉-铕(Eu(DBM)3BPhen)作为电子给体和[6,6]-苯基-C61-丁酸酸甲酯([60]PCBM)作为电子受体制备了一种新型的有机光盲型紫外探测器.在光强为2.1 mW cm-2且波长为360 nm的紫外光照射下,获得了26 mA W-1的响应度和9.1%的外量子效率,这是由于Eu(DBM)3BPhen的强紫外光吸收能力和长达300μs的激子寿命使得给受体界面处具有较高的激子解离率.在把[60]PCBM掺入Eu(DBM)3BPhen后,观察到了明显的光致发光猝灭和光电导现象.由于材料较低的载流子迁移率和受陷激子的缓慢释放,在紫外光照射关闭后,观察到了较强的持续光电导现象.     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Design and synthesis of dithieno[3,2‐b:2′3′‐d]pyrrole‐based conjugated polymers for photovoltaic applications: consensus between low bandgap and low HOMO energy level

A strategy of the fine‐tuning of the degree of intrachain charge transfer and aromaticity of polymer backbone was adopted to design and synthesize new polymers applicable in photovoltaics. Three conjugated polymers P1 , P2 , and P3 were synthesized by alternating the electron‐donating dithieno[3,2‐b:2′3′‐d]pyrrole (D) and three different electron‐accepting (A) segments ( P1 : N‐(2‐ethylhexyl)phthalimide; P2 : 1,4‐diketo‐3,6‐diphenylpyrrolo[3,4‐c]pyrrole; and P3 : thiophene‐3‐hexyl formate) in the polymer main chain. Among the three polymers, P2 possessed the broadest absorption band ranging from 300 to 760 nm, the lowest bandgap (1.63 eV), and enough low HOMO energy level (?5.27 eV) because of the strong intrachain charge transfer from D to A units and the appropriate extent of quinoid state in the main chain of P2 , which was convinced by the theoretical simulation of molecular geometry and front orbits. Photovoltaic study of solar cells based on the blends of P1 – P3 and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) demonstrated that P2 :PCBM exhibited the best performance: a power conversion efficiency of 1.22% with a high open‐circuit voltage (V_OC) of 0.70 V and a large short‐circuit current (I_SC) of 5.02 mA/cm² were achieved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A Supramolecular Approach on Using Poly(fluorenylstyrene)‐block‐poly(2‐vinylpyridine):PCBM Composite Thin Films for Non‐Volatile Memory Device Applications

Supramolecular composite thin films of poly[4‐(9,9‐dihexylfloren‐2‐yl)styrene]‐block ‐poly(2‐vinylpyridine) (P(St‐Fl)‐b‐P2VP):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) were prepared for write‐once‐read‐many times (WORM) non‐volatile memory devices. The optical absorption and photoluminescence results indicated the formation of charge transfer complexation between the P2VP block and PCBM, which led to the varied PCBM aggregated size and memory characteristics. The ITO/PCBM:(P(St‐Fl)‐b‐P2VP)/Al device exhibited the WORM characteristic with low threshold voltage (−1.6 to −3.2 V) and high ON/OFF ratio (10³ to 10⁵) by tuning the PCBM content. The switching behavior could be explained by the charge injection dominated thermionic emission in the OFF state and field‐induced charge transfer in the ON state. The present study provides a novel approach system for tuning polymer memory device characteristics through the supramolecular materials approach.

     

Theoretical Studies on the Electronic Structures and Optical Properties of Tri-aryl End-capped Terthiophene Derivatives

The relationships between electronic structures and spectra properties are investigated by DFT/TDDFT for terthiophene derivatives, BMA‐3T (tri‐aryl amine end‐capped terthiophene), BBA‐3T (tri‐aryl amine and tri‐aryl boron end‐capped terthiophene) and BPB‐3T (tri‐aryl boron end‐capped terthiophene). The calculated results show that BMA‐3T, BBA‐3T and BPB‐3T have higher HOMO energy level and lower ionization potentials (IPs) than 3T. BMA‐3T has good hole injection ability and hole‐transport property as reported in experiment. The designed molecule of BBA‐3T and BPB‐3T own lower LUMO level and higher electron affinities (EAs) than BMA‐3T, which facilitate electron injection and improve their electron‐transport properties. Surprisingly, BPB‐3T has preferable charge equilibrium property since its hole reorganization energy (λ_h) is close to electron reorganization energy (λ_e). The ΔE (HOMO−LUMO) and E_g of these three derivatives are narrower compared to 3T, and the absorption as well as emission spectrum exhibited red‐shifts.     

基于苯并噻二唑和硅芴的一系列红光材料的载流子传输性质及荧光性质(英文)

用密度泛函理论(DFT)方法研究了基于苯并噻二唑和硅芴的一系列聚合物的基态和激发态结构、传输和荧光性质.聚合物的能隙、电离能、电子亲和势、最低激发能以及吸收光谱通过外推法得到.结果表明空穴、电子注入和传输性质受苯并噻唑在硅芴上的位置以及正丁基在噻吩上的位置影响很大.(SiF2-DHTBT1-m)n和(SiF1-DHTBT1-m)n(SiF和DHTBT分别代表硅芴和4,7-二(2-噻吩基)-2,1,3-苯并噻二唑)表现出较好的空穴和电子注入性质,而(SiF1-DHTBT1-o)n和(SiF1-DHTBT1-p)n的电荷注入性质较差.除(SiF1-DHTBT1-o)n外,聚合物的荧光光谱处于红光范围.     

Modifying transparent electrode with conjugated organic semiconductor hole transport material as interface for enhancing performance of organic solar cell

Indium tin oxide (ITO) is used as a substrate was covered with 4-[4-(4-methoxy-N-naphthalen-2-ylanilino) phenyl] benzoic acid (MNA) as a self-assembled monolayer (SAM). Poly(3-hexylthiophene) (P3HT) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6) C₆₁ (PCBM) were mixed and used as a donor–acceptor in organic solar cell (OSC). The MNA (SAM) layer is used as an interface instead of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT: PSS) for hole injection. The HOMO-LUMO energy level of MNA-SAM molecule and the electronic charge distribution were calculated theoretically using Chemissian software. The HOMO-LUMO energy level of the MNA is calculated as E_HOMO = ?5.10 eV and E_LUMO = ?1.60 eV. The OSC modified with MNA showed an efficient performance in the absence of PEDOT: PSS as hole transport layer. The annealing of the ITO/SAM/P3HT: PCBM films at different temperatures are also investigated to study the effect of reducing defects. The interface structures of the organic semiconductor layer on ITO were characterized by Atomic Force Microcopy (AFM). In addition, Kelvin Probe Microscopy (KPM) is used to understand how the annealing changes the surface potential energy of the ITO/SAM substrate. Using the KPM method, which measures the surface potential energy of the films, the energy bands of the ITO were increased to maximum 5.09 eV. The ITO/SAM/P3HT: PCBM film's surface potential was determined to be 0.18 eV after being annealed at 80 °C. The surface potential of the modified films was discovered to be 0.33 V and 0.39 V when the annealing temperature was raised from 80 °C to 120 °C and 160 °C. The maximum device efficiency was demonstrated by the ITO/SAM/P3HT: PCBM film after an hour of annealing at 160 °C.     

Phthalimide and Naphthalimide end‐Capped Diketopyrrolopyrrole for Organic Photovoltaic Applications

Two small molecules named PI‐DPP and NI‐DPP with a DPP core as the central strong acceptor unit and phthalimide/naphthalimide as the terminal weak acceptor were designed and synthesized. The effects of terminal phthalimide/naphthalimide units on the thermal behavior, optical and electrochemical properties, as well as the photovoltaic performance of these two materials were systematically studied. Cyclic voltammetry revealed that the lowest unoccupied molecular orbitals (LUMO) (~ ‐3.6 eV) of both molecules were intermediate to common electron donor (P3HT) and acceptor (PCBM). This indicated that PI‐DPP and NI‐DPP may uniquely serve as electron donor when blended with PCBM, and as electron acceptor when blended with P3HT, where sufficient driving forces between DPPs and PCBM, as well as between P3HT and DPPs should be created for exciton dissociation. Using as electron donor materials, PI‐DPP and NI‐DPP devices exhibited low power conversion efficiencies (PCEs) of 0.90% and 0.76% by blending with PCBM, respectively. And a preliminary evaluation of the potential of the NI‐DPP as electron acceptor material was carried out using P3HT as a donor material, and P3HT: NI‐DPP device showed a PCE of 0.6%, with an open circuit voltage (V _OC) of 0.7 V, a short circuit current density (J _SC) of 1.91 mA•cm^‐2, and a fill factor (FF) of 45%.