Structural relation and epitaxial properties of hexagonal InN and oxidized cubic In2O3

The epitaxial properties and structural relation between hexagonal InN and cubic In₂O₃ phases were studied by synchrotron X-ray scattering and X-ray photoelectron spectroscopy. The cubic bixbyite In₂O₃ phase on the sapphire(0001) substrate was formed after an annealing time of 10 min at 10⁻⁵ Torr after the hexagonal InN film was grown at 550 °C, above the dissociation temperature of InN, by RF-magnetron sputtering. The crystal orientation was cubic In₂O₃(222), parallel to Al₂O₃(0001) and parallel to hexagonal InN(0002) before the oxidation process. The cubic In₂O₃ phase was believed to be formed layer by layer by the oxidation of the hexagonal InN phase.     

An extreme change in structural and optical properties of indium oxynitride deposited by reactive gas-timing RF magnetron sputtering

The indium oxynitride (InON) films were achieved by reactive RF magnetron sputtering indium target which has the purity of 99.999% with a novel reactive gas-timing technique. The structural, optical and electrical properties in a series of polycrystalline InON films affected by gas-timing of reactive N₂ and O₂ gases introduced to the chamber were observed. The X-ray photoelectron spectroscopy revealed that the oxygen content in thin films that compounded to indium and nitrogen, which increased from 10% in indium nitride (InN) to 66% in indium oxide (In₂O₃) films. The X-ray diffraction peaks show that the phase of deposited films changes from InN to InON and to In₂O₃ with an increasing oxygen timing. The hexagonal structure of InN films with predominant (0 0 2) and (0 0 4) orientation was observed when pure nitrogen is only used as sputtering gas, while InON and In₂O₃ seem to demonstrate body-center cubic polycrystalline structures depending on gas-timing. The surface morphologies investigated from atomic force microscope of deposited films with varying gas-timing of O₂:N₂ show indifferent. The numerical algorithm method was used to define the optical bandgap of films from transmittance results. The increasing oxygen gas-timing affects extremely to the change of crystallinity phase from InN to InON and to In₂O₃, the increase of optical bandgap from 1.4 to 3.4 eV and the rise of sheet resistance from 15 Ω/□ to insulator.     

Growth of InN films on spinel substrates by pulsed laser deposition

We have grown InN films on MgAl₂O₄(111) substrates with atomically flat surfaces using pulsed laser deposition (PLD) and compared their structural properties with those grown on (Mn,Zn)Fe₂O₄(111) substrates. It has been revealed that InN(0001) films grow on MgAl₂O₄(111) with an in‐plane epitaxial relationship of InN[1 00] // MgAl₂O₄[1 0], achieving a lattice mismatch minimum. The InN films exhibited a clear sixfold rotational symmetry, without 30° rotational domains and with a full width at half maximum value of the InN 0002 rocking curve being 17.5 arcmin. Comparison between InN films grown on MgAl₂O₄ and those on (Mn,Zn)Fe₂O₄ led us to conclude that suppression of the interfacial reactions between the InN films and the substrate is inherently important to obtain high quality InN on substrates with a spinel structure. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Epitaxial growth of InN on nearly lattice-matched (Mn,Zn)Fe2O4

We have grown InN films on nearly lattice-matched (Mn,Zn)Fe₂O₄ (111) substrates at low temperatures by pulsed laser deposition (PLD) and investigated their structural properties. InN films grown at substrate temperatures above 400 °C show poor crystallinity, and their in-plane epitaxial relationship is [10-10]InN//[11-2](Mn,Zn)Fe₂O₄, which means that their lattice mismatch is quite large (11%). By contrast, high quality InN films with flat surfaces can be grown at growth temperatures lower than 150 °C with the ideal in-plane epitaxial relationship of [11-20]InN//[11-2](Mn,Zn)Fe₂O₄, which produces lattice mismatches of as low as 2.0%. X-ray reflectivity measurements have revealed that the thickness of the interfacial layer between the InN and the substrates is reduced from 14 to 8.4 nm when the growth temperature is decreased from 400 °C to room temperature. This suppression of the interface reactions by reducing the growth temperature is probably responsible for the improvement in crystalline quality. These results indicate that the use of (Mn,Zn)Fe₂O₄ (111) substrates at low growth temperatures allows us to achieve nearly lattice matched epitaxial growth of InN.     

Characterization of interface between CuInSe2 and In2O3

CuInSe₂/In₂O₃ structures were formed by depositing CuInSe₂ films by stepwise flash evaporation onto In₂O₃ films, which were grown by DC reactive sputtering of In target in presence of (Ar+O₂) gas mixture. Phase purity of the CuInSe₂ and In₂O₃ films was confirmed by Transmission Electron Microscopy (TEM) studies. X-ray diffraction (XRD) results on CuInSe₂/In₂O₃/glass structures showed sharp peaks corresponding to (112) plane of CuInSe₂ and (222) plane of In₂O_3. Rutherford Backscattering Spectrometry (RBS) investigations were carried out on CuInSe₂/In₂O₃/Si structures in order to characterize the interface between In₂O₃ and CuInSe₂. The results show that the CuInSe₂ films were near stoichoimetric and In₂O₃ films had oxygen deficient composition. CuInSe₂/In₂O₃ interface was found to include a ∼20 nm thick region consisting of copper, indium and oxygen. Also, the In₂O₃/Si interface showed the formation of ∼20 nm thick region consisting of silicon, indium and oxygen. The results are explained on the basis of diffusion/reaction taking place at the respective interfaces.     

Synthesis,structural and ellipsometric evaluation of oxygen-deficient and nearly stoichiometric zinc oxide and indium oxide nanowires/nanoparticles

Oxygen-deficient (OD) and nearly stoichiometric (NST) ZnO and In₂O₃ nanowires/nanoparticles were synthesized by chemical vapor deposition on Au-coated silicon substrates. The OD ZnO and OD In₂O₃ nanowires were synthesized at 750 and 950°C, respectively, using Ar flow at ambient pressure. A mixture of flowing Ar and O₂ was used for synthesizing NST ZnO nanowires and NST In₂O₃ nanoparticles. Growth of OD ZnO nanowires and NST In₂O₃ nanoparticles was found to be via a vapor–solid (VS) mechanism and the growth of NST ZnO nanowires was via a vapor–liquid–solid mechanism (VLS). However, it was uncertain whether the growth of OD In₂O₃ nanowires was via a VS or VLS mechanism. The optical constants, thickness and surface roughness of the prepared nanostructured films were determined by spectroscopic ellipsometry measurements. A three-layered model was used to fit the calculated data to the experimental ellipsometric spectra. The refractive index of OD ZnO, NST ZnO nanowires and NST In₂O₃ nanoparticles films displayed normal dispersion behavior. The calculated optical band gap values for OD ZnO, NST ZnO, OD In₂O₃ nanowires and NST In₂O₃ nanoparticles films were 3.03, 3.55, 2.81 and 3.52?eV, respectively.     

The explanation of InN bandgap discrepancy based on experiments and first-principle calculations

Indium nitride (InN) films with different free electron concentration and optical bandgap were grown either directly on sapphire substrate or on pre-covered gallium nitride (GaN) buffer through metal-organic chemical vapor deposition (MOCVD) method. Based on first-principle calculations, we confirm that the widening of InN optical bandgap reported before is caused by high density of free electrons. To find the contributor of the free electrons, the characteristic energetic levels of O_N, V_N and Si_In are investigated. We find that they are all high enough to uplift the optical bandgap from about 0.78 eV to 1.9 eV, which almost can't be enlarged further when it reaches 2.09 eV.     

Application of MEH-PPV/SnO<Subscript>2</Subscript> bilayer as hybrid solar cell

The effects of oxygen content in the sputtering gas on the crystallographic and optoelectronic properties of 210 nm-thick Zr–doped In₂O₃ (Zr–In₂O₃) films by rf magnetron sputtering were initially studied. The results of X-ray diffraction show that the Zr–In₂O₃ films grown on glass substrates exhibit mixed crystallographic orientations. Moreover, the Zr–In₂O₃ film grown in an Ar atmosphere promotes the appearance of crystallographic orientation of (222). The surface of the Zr–In₂O₃ film becomes rougher as the oxygen content in the sputtering gas decreases; the current images obtained by conductive atomic force microscopy reveal that the surfaces of the Zr–In₂O₃ films exhibit a distribution of coexisting conducting and nonconducting regions, and that the area of the nonconducting surface increases with the oxygen content in the sputtering gas. The resistivity is minimized to 3.51×10⁻⁴ Ω cm when the Zr–In₂O₃ film is grown in an Ar atmosphere and the average transmittance in the visible light region is ∼85%. The optical band gap decreases as the oxygen content in the sputtering gas increases.     

Effect of thermal treatment on the electrotransport properties of thin-film In<Subscript>2</Subscript>O<Subscript>3</Subscript>, ZnO materials and the multilayer (In<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZnO)<Subscript>83</Subscript> heterostructure

The effect heat treatment has on the electrotransport mechanisms in films of ZnO and In₂O₃, and in a multilayer (In₂O₃/ZnO)₈₃ structure obtained via ion-beam sputtering, is studied. It is shown that there is a mechanism of weak electron localization in the In₂O₃ and (In₂O₃/ZnO)₈₃ samples. The relaxation processes that occur during the heat treatment of In₂O₃ films are found to increase the length of elastic electron scattering, but to reduce this parameter in multilayer heterostructures.     

The structure and optical characters of the ZnO film grown on GaAs/Al2O3 substrate

In this paper ZnO films are grown on GaAs/Al₂O₃ substrates at different temperature by metal-organic chemical vapor deposition (MOCVD). The GaAs/Al₂O₃ substrates are formed by depositing GaAs layer (∼35 nm) on the Al₂O₃ substrate. The results of X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) demonstrate that most of the Ga and As atoms form Ga-As bond and the GaAs layer does not present any orientation. The characters of the ZnO films grown on GaAs/Al₂O₃ substrates are investigated by XRD, photoluminescence (PL), atomic force microscopy (AFM) and Raman scattering. Compared with ZnO film grown on Al₂O₃ substrate, ZnO film prepared by our fabrication scheme has good crystal and optical quality. Meanwhile its grain size becomes bigger according to the AFM image. Raman analysis indicates that the intrinsic defects and the in-plane tensile stress are obviously reduced in ZnO/GaAs/Al₂O₃ samples.     

Characteristics of High In-Content InGaN Alloys Grown by MOCVD

InN and In0.46 Ca0.54N films are grown on sapphire with a CaN buffer by metalorganic chemical vapour deposition （MOCVD）. Both high resolution x-ray diffraction and high resolution transmission electron microscopy results reveal that these films have a hexagonal structure of single crystal. The thin InN film has a high mobility of 4 75 cm^2V^-1s^-1 and that oflno.46 Gao.54N is 163 cm^2 V^-1s^-1. Room-temperat ure photoluminescence measurement of the InN film shows a peak at 0.72eV, confirming that a high quality InN film is fabricated for applications to full spectrum solar cells.     

Effects of sapphire substrate annealing on ZnO epitaxial films grown by MOCVD

The annealing effects of sapphire substrate on the quality of epitaxial ZnO films grown by metalorganic chemical vapor deposition (MOCVD) were studied. The atomic steps formed on (0 0 0 1) sapphire (α-Al₂O₃) substrate surface by annealing at high temperature was analyzed by atomic force microscopy (AFM). The annealing effects of sapphire substrate on the ZnO films were examined by X-ray diffraction (XRD), AFM and photoluminescence (PL) measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface. The optimum annealing temperature of sapphire substrates is given.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Dependences of the surface and the optical properties on the O2/O2 + Ar flow-rate ratios for ZnO thin films grown on ZnO buffer layers

ZnO active layers on ZnO buffer layers were grown at various O₂/O₂ + Ar flow-rate ratios by using radio-frequency magnetron sputtering. Atomic force microscopy images showed that the surface roughnesses of the ZnO active layers grown on ZnO buffer layers decreased with decreasing O₂ atmosphere, indicative of an improvement in the ZnO surfaces. The type of the ZnO active layer was n-type, and the resistivity of the layer increased with increasing O₂ atmosphere. Photoluminescence spectra from the ZnO active layers grown on the ZnO buffer layers showed dominant peaks corresponding to local levels in the ZnO energy gap resulting from oxygen vacancies or interstitial zinc vacancies, and the peak positions changed significantly with the O₂/O₂ + Ar flow rate. These results can help improve understanding of the dependences of the surface and the optical properties on the O₂/O₂ + Ar ratio for ZnO thin films grown on ZnO buffer layers.     

Co-doped In2O3 thin films: Room temperature ferromagnets

Laser-ablated Co-doped In₂O₃ thin films were fabricated under various growth conditions on R-cut Al₂O₃ and MgO substrates. All Co:In₂O₃ films are well-crystallized, single phase, and room temperature ferromagnetic. Co atoms were well substituted for In atoms, and their distribution is greatly uniform over the whole thickness of the films. Films grown at 550 °C showed the largest magnetic moment of about 0.5 μ_B/Co, while films grown at higher temperatures have magnetic moments of one order smaller. The observed ferromagnetism above room temperature in Co:In₂O₃ thin films has confirmed that doping few percent of magnetic elements such as Co into In₂O₃ could result in a promising magnetic material.     

Photosensitivity of nanocrystalline ZnO films grown by PLD

We have studied the properties of ZnO thin films grown by laser ablation of ZnO targets on (0 0 0 1) sapphire (Al₂O₃), under substrate temperatures around 400 °C. The films were characterized by different methods including X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and atomic force microscopy (AFM). XPS analysis revealed that the films are oxygen deficient, and XRD analysis with θ-2θ scans and rocking curves indicate that the ZnO thin films are highly c-axis oriented. All the films are ultraviolet (UV) sensitive. Sensitivity is maximum for the films deposited at lower temperature. The films deposited at higher temperatures show crystallite sizes of typically 500 nm, a high dark current and minimum photoresponse. In all films we observe persistent photoconductivity decay. More densely packed crystallites and a faster decay in photocurrent is observed for films deposited at lower temperature.     

Laser–MBE growth of high-quality ZnO thin films on Al2O3(0001) and SiO2/Si(100) using the third harmonics of a Nd:YAG laser

High-quality ZnO thin films were grown on single-crystalline Al₂O₃(0001) and amorphous SiO₂/Si(100) substrates at 400–640 °C using laser molecular beam epitaxy. For film growth, the third harmonics of a pulsed Nd:YAG laser were illuminated on a ZnO target. The ZnO films were epitaxially grown on Al₂O₃(0001) with the narrow X-ray diffraction full width at half maximum (FWHM) of 0.04° and the films on SiO₂/Si(100) exhibited a preferred c-axis orientation. Furthermore, the films exhibited excellent optical properties in photoluminescence (PL) measurements with very sharp excitonic and weak deep-level emission peaks. At 15 K, PL FWHM values of the films grown on Al₂O₃(0001) and SiO₂/Si(100) were 3 and 18 meV, respectively. Received: 8 May 2001 / Accepted: 18 September 2001 / Published online: 20 December 2001     

Characterization of ZnO thin films grown on various substrates by RF magnetron sputtering

In this study we investigated properties of ZnO thin films deposited on both oxygen-containing substrates and a substrate without oxygen content at various O₂/Ar reactant gas ratios. Deposition of ZnO on indium-tin oxide (ITO) resulted in the best crystallinity, whereas the least degree of crystallization was observed from ZnO deposited on glass. All the films were found to have compressive stress, which was relieved by annealing in O₂ environment. ZnO films deposited on glass revealed p-type conductivity when prepared at O₂/Ar ratio of 0.25 whereas those on SiN_x yielded p-type conductivity when prepared at O₂/Ar ratio of 4. In addition, shallower oxygen interstitial seemed to be found from films with better crystallinity. The largest shift in binding energy of Zn_2p3/2 was observed from ZnO prepared on glass at O₂/Ar ratio of 0.25, whereas that of O_1s was obtained from ZnO deposited on SiN_x at O₂/Ar ratio of 4. A model was proposed in terms of O₂ diffusion and hydrogen desorption in order to account for the observed property variations depending on substrates and O₂/Ar ratios.     

Optical properties of In2O3 oxidized from InN deposited by reactive magnetron sputtering

Unintentionally doped and zinc-doped indium nitride (U-InN and InN:Zn) films were deposited on (0 0 0 1) sapphire substrates by radio-frequency reactive magnetron sputtering, and all samples were then treated by annealing to form In₂O₃ films. U-InN and InN:Zn films have similar photon absorption characteristics. The as-deposited U-InN and InN:Zn film show the absorption edge, ∼1.8-1.9 eV. After the annealing process at 500 °C for 20 min, the absorption coefficient at the visible range apparently decreases, and the absorption edge is about 3.5 eV. Two emission peaks at 3.342 eV (371 nm) and 3.238 eV (383 nm) in the 20 K photoluminescence (PL) spectrum of In₂O₃:Zn films were identified as the free-exciton (FE) or the near band-to-band (B-B) and conduction-band-to-acceptor (C-A) recombination, respectively.