Synthesis of fine-crystalline Ba0.6Sr0.4TiO3-MgO ceramics by novel hybrid processing route

We report the use of a novel powder-in-sol precursor hybrid processing route to synthesize dense, homogeneous, and fine-crystalline Ba_0.6Sr_0.4TiO₃-MgO (BST-MgO) ceramics as well as the study of the sintering behavior, microstructures, and dielectric properties of the ceramics. Nanosized BST powders are dispersed into BST sol-gel precursor and uniformly distributed BST slurry is obtained after ball-milling mixing. Mg(NO₃)·6H₂O solution is added to the BST slurry to give homogeneous BST-MgO slurry upon ball-milling mixing. The BST-MgO slurry is dried and calcined prior to pressing and sintering at low temperatures of 1200-1300 °C to form the ceramics. The ceramics possess very low dielectric loss tangent below 0.005 for frequency above 1 kHz and for temperature in the range −190-80 °C. The dielectric constant and dielectric tunability increase, while the ferroelectric transition broadening decreases, with increasing average grain size.     

Post-sintering annealing effect on the diffuse phase transition in (Pb1−xBax)(Yb0.5Ta0.5)O3 ceramics

The effect of post sintering annealing on the dielectric response of (Pb_1−xBa_x)(Yb_0.5Ta_0.5)O₃ ceramics in the diffuse phase transition range (x=0.2) has been investigated. The samples are prepared by conventional solid-state reaction method. The samples are sintered at 1300 °C for 2 h and annealed at different temperatures (800, 900 and 1000 °C) for 8 h and at 800 °C for different time durations (8, 12 and 24 h). A significant change in the dielectric response has been observed in all the samples. The dielectric constant increases remarkably and the dielectric loss tangent decreases. The dielectric peaks of the annealed samples are observed to be more diffused with noticeable frequency dispersion compared to the as sintered sample.     

Dielectric and leakage current properties of Li doped (Ba,Sr)TiO3 thick film interdigital capacitors on the alumina substrates

Li doped (Ba,Sr)TiO₃ thick films were fabricated by employing the screen printing method on the alumina (Al₂O₃) substrates. Interdigital capacitor patterns with seven fingers of 200 μm gap, 250 μm length were designed and screen printed on the alumina substrates. Ba_0.5Sr_0.5TiO₃ materials, paraelectric state at the room temperature, have been chosen for the microwave devices due to high dielectric permittivity and low loss tangent, however, the sintering temperature of (Ba,Sr)TiO₃ is over 1350 °C. In order to lower the sintering temperature, Li (3 wt%) was added to the (Ba,Sr)TiO₃ materials. Li doped (Ba,Sr)TiO₃ thick films screen printed on the alumina (Al₂O₃) substrates were sintered at 900 °C for 1.5 h. The structural feature was analyzed with X-ray diffraction method. Temperature dependent dielectric properties were characterized from 303 to 403 K at 1 MHz. Within the ±100 V of bias voltage, current-voltage characteristics of Li doped (Ba,Sr)TiO₃ films were investigated from 303 to 403 K. Through the current-voltage characteristics, the resistivity of Li doped (Ba,Sr)TiO₃ films were calculated.In this paper, the significant negative temperature coefficient of resistance (NTCR) of Li doped (Ba,Sr)TiO₃ films will be presented through the activation energy fitting. Measured activation energy is approximately 0.366 eV.     

Low-temperature sintering and microwave dielectric properties of Ca2Zn4Ti15O36 ceramics

The sintering behavior, microstructures, and microwave dielectric properties of Ca₂Zn₄Ti₁₅O₃₆ ceramics with B₂O₃ addition were investigated. The crystalline phases and microstructures of Ca₂Zn₄Ti₁₅O₃₆ ceramics with 0-10 wt% B₂O₃ addition were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The sintering temperature of Ca₂Zn₄Ti₁₅O₃₆ ceramic was lowered from 1170 to 930 °C by 10 wt% B₂O₃ addition. Ca₂Zn₄Ti₁₅O₃₆ ceramics with 8 wt% B₂O₃ addition sintered at 990 °C for 2 h exhibited good microwave dielectric properties, i.e., a quality factor (Qf) 11,400 GHz, a relative dielectric constant (ε_r) 41.5, and a temperature coefficient of resonant frequency (τ_f) 94.4 ppm/°C.     

Dielectric properties and magnetoelectric effect of (x)NiFe2O4+(1−x)Ba0.8Sr0.2TiO3 composites

Magnetoelectric composites of NiFe₂O₄ and Ba_0.8Sr_0.2TiO₃ were prepared using conventional double-sintering ceramic method. The phase formation of magnetoelectric composites was confirmed by XRD technique. Variation of dielectric constant and loss tangent at room temperature with frequency in the range 100 Hz-1 MHz has been studied. Also the variation of dielectric constant and loss tangent with temperature and composition at fixed frequencies of 1 kHz, 10 kHz, 100 kHz and 1 MHz is reported. The static value of the magnetoelectric conversion factor was measured as a function of intensity of the magnetic field. The ME voltage coefficient of about 430 μV/cm Oe was observed for 15% NiFe₂O₄+85% Ba_0.8Sr_0.2TiO₃ composite. All the samples show linear variation of magnetoelectric conversion in the presence of static magnetic field.     

Effect of bismuth deficiency on structure and electrical properties of (Na0.5Bi0.5)0.93Ba0.07TiO3 ceramics

(Na_0.5Bi_x)_0.93Ba_0.07TiO₃ (x=0.500-0.492) ceramics were prepared by a citrate method, and the structure and electrical properties of the ceramics were investigated with respect to the amount of Bi deficiency. It was detected that the Bi deficiency had a considerable impact on the crystal structure and microstructure. The inspection of both the temperature dependence of the dielectric properties (free permittivity ε₃₃^T/ε₀ and dielectric loss tan δ) and the evolution of the polarization-electrical field (P-E) hysteresis loops with measuring temperature suggests that the Bi deficiency served to increase the depolarization temperature (T_d). The Bi deficiency led to an increase in the coercive field (E_c) and mechanical quality factor (Q_m) together with a decrease in the remanent polarization (P_r) and piezoelectric constants (d₃₃). The variation of the structure and electrical properties with Bi deficiency amount was qualitatively interpreted in terms of the formation of Bi and oxygen vacancies in the Bi-deficient specimens. This research indicates the importance of adequately controlling Bi stoichiometry of (Na_0.5Bi_0.5)_0.93Ba_0.07TiO₃ ceramics in obtaining the desired ferroelectric and piezoelectric properties.     

Improvement of dielectric tunability and loss tangent of (Ba,Sr)TiO3 thin films with K doping

Ba_0.6Sr_0.4TiO₃ thin films doped with K were deposited on Pt/Ti/SiO₂/Si substrates by chemical solution deposition method. The structure, surface morphology, and dielectric and tunable properties of Ba_0.6Sr_0.4TiO₃ thin films have been studied in detail. The K content in Ba_0.6Sr_0.4TiO₃ thin films has a strong influence on the material's properties including surface morphology, dielectric and tunable properties. It is found that the Curie temperature of K-doped Ba_0.6Sr_0.4TiO₃ films shifts to higher values compared with that of undoped Ba_0.6Sr_0.4TiO₃ thin films, which leads to a dielectric enhancement of K-doped Ba_0.6Sr_0.4TiO₃ films at room temperature. At the optimized content of 0.02 mol, the dielectric loss tangent is reduced significantly from 0.057 to 0.020. Meanwhile, the tunability is enhanced obviously from 26% to 48% at the measured frequency of 1 MHz and the maximum value of the figure of merit is 23.8. This suggests that such films have potential applications for tunable devices.     

Magnetic and dielectric behaviors of Ba0.2Sr0.8Co0.8Fe0.2O3-δ oxide

Ba_0.2Sr_0.8Co_0.8Fe_0.2O_3-δ (BSCFO) ceramic oxide has been synthesized by combined citrate-EDTA complexing method and studied with regard to their structural, magnetic and dielectric properties. It is shown that the compound exhibits perovskite-type cubic structure. It depicts hysteresis loop in presence of magnetic field—indicating its magnetic nature. The dielectric properties of sintered oxide were investigated in temperature range (373-873 K) and frequency (100 kHz-1 MHz).The ferroelectric and ferrimagnetic transition temperatures were found to be around 700 K.     

Effect of fabrication parameters on the electrical conductivity of YxSr1−xTiO3 for anode materials

Yttrium-doped strontium titanate (Y_xSr_1−xTiO₃), as probable anode material for SOFC, was prepared by solid-state reaction. The solubility of yttrium in SrTiO₃ at different temperatures was examined and the electrical conductivities of Y_xSr_1−xTiO₃ were measured from 500 to 1000 °C. The effects of doping amount, fabrication atmosphere, and sintering temperature on the electrical conductivity of Y_xSr_1−xTiO₃ were investigated. Y_xSr_1−xTiO₃ with x=0.08 was found to give the maximum electrical conductivity, 71 S/cm at 800 °C in pure hydrogen. Reducing atmospheres and appropriate sintering temperatures play a positive role in improving the electrical conductivity.     

Strongly oriented BST films on La0.9Sr1.1NiO4 electrodes deposited on various substrates for integration of high capacitances on silicon

In this study, we demonstrate the successful oriented growth of Ba_0.6Sr_0.4TiO₃(h 0 0)/La_0.9Sr_1.1NiO₄(0 0 l) stacks by pulsed laser deposition on SiO₂/Si for application in integrated capacitances. We show that for specific deposition conditions the La_0.9Sr_1.1NiO₄ layer spontaneously grows along its c-axis both on SiO₂/Si and on Pt/Ti/SiO₂/Si substrates, serving as a template for the subsequent oriented growth of Ba_0.6Sr_0.4TiO₃ (BST). Moreover, as the resistivity of the La_0.9Sr_1.1NiO₄ layer is ∼1 mΩ cm, it also fulfills the function of bottom electrode for integration of perovskite-based capacitors on silicon. This holds the promise of integrating epitaxial BST with very high dielectric constant compared to polycrystalline BST films. Still, preliminary capacitance measurements on Al/BST/La_0.9Sr_1.1NiO₄/SiO₂/Si capacitors indicate that the stack deposition needs further optimization.     

Na0.5K0.5NbO3-BiFeO3 lead-free piezoelectric ceramics

Lead-free (Na_0.5K_0.5)NbO₃-based piezoelectric ceramics were successfully fabricated by substituting with a small amount of BiFeO₃ (BF). Difficulty in sintering of pure NKN ceramics can be eased by adding a few molar percent of BF, and the crystalline structure is also changed, leading to a morphotropic phase boundary (MPB) between ferroelectric orthorhombic and rhombohedral phases. The MPB exists near the 1-2 mol% BF-substituted NKN compositions, exhibiting enhanced ferroelectric, piezoelectric, and electromechanical properties of P_r=23.3 μC/cm², d₃₃=185 pC/N, and k_p=46%, compared to an ordinarily sintered pure NKN ceramics. The MPB composition has a Curie temperature of ∼370 °C, comparable to that of some commercial PZT materials.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

Improvement of electrical properties of Sr-modified (Pb,Ca)TiO3 thin films grown by soft chemistry route

Strontium and calcium-modified lead titanate (Pb_0.70Ca_0.15Sr_0.15)TiO₃ soft chemistry-derived thin films were prepared on platinum-coated silicon substrate by spin-coating method. Investigations were made on the structure, surface morphology and electrical properties of the film. The results by XRD and FE-SEM showed that the film exhibits a pure tetragonal perovskite phase and an average grain size of about 50-60 nm, respectively. Electrical measurements of a metal-ferroelectric-metal type capacitor exhibited a stable and switchable electrical polarization in the film. The structure of the Au/PCST/Pt capacitor showed well-saturated hysteresis loops at an applied voltage of 300 kV/cm with remanent polarization and coercive field values of 22 μC/cm² and 100 kV/cm, respectively. At 100 kHz, the dielectric constant and the dielectric loss of the (Pb_0.70Ca_0.15Sr_0.15)TiO₃ thin film with thickness 240 nm were 528 and 0.05, respectively.     

Densification, microstructural evolution, and dielectric properties of CaTiO3-LaGaO3 microwave ceramics

The relations among the densification, microstructural evolution, and microwave dielectric properties of the (1−x)CaTiO₃-xLaGaO₃ ceramics with x=0.34 and 0.36 were investigated in this study. The results indicated that (1−x)CaTiO₃−xLaGaO₃ ceramics can be densified at 1300 °C with at least 97% of the theoretical value. The ceramics reported an orthorhombic perovskite structure, and no other detectable phases were found. Both ε_r and Q×f values can be improved by slowing the cooling rate during sintering. The ε_r and Q×f values of the 0.64CaTiO₃-0.36LaGaO₃ ceramics at cooling rates of >10 °C/min and 0.1 °C/min are 48.1 and 27,500 and 48.7 and 38,000, respectively. The higher densification obtained at a slower cooling rate plays an important role in improving the microwave dielectric properties.     

Field history dependence of nonlinear dielectric properties of Ba0.6Sr0.4TiO3 ceramics under bias electric field: Polarization behavior of polar nano-regions

Nonlinear dielectric properties of Ba_0.6Sr_0.4TiO₃ ceramics prepared by citrate method were investigated under bias electric field with respect to field history. X-ray diffraction analysis and temperature dependence of the dielectric constant (ε_r) confirmed a macroscopically paraelectric state for the specimen at room temperature. A slim polarization versus electric field (P-E) hysteresis loop of the specimen at room temperature indicated the existence of polar nano-regions (PNRs) superimposed on the paraelectric background. The nonlinear dielectric properties in continuous cycles of bias field sweep displayed a strong sensitivity to the field history. This phenomenon was qualitatively explained in terms of an irreversible polarization evolution of the PNRs under the bias fields. A considerable decline of the tunability with the cycle number suggests an appreciable contribution of the PNRs to the dielectric nonlinearity. The polarization and size of the PNRs were determined by fitting the dielectric constants to a multipolarization mechanism model.     

Effects of Li2CO3 on the sintering behavior and piezoelectric properties of Bi2O3-excess (Bi0.5Na0.5)0.94Ba0.06TiO3 ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ ceramics doped with Li₂CO₃ and Bi₂O₃ as sintering aids were manufactured, and their micro structural, dielectric and piezoelectric properties were investigated. All specimens could be well sintered at a low-temperature of 1080 °C. The bulk density of the specimens doped with a small amount of Li₂CO₃ was enhanced. The dielectric and piezoelectric properties of ceramics were investigated with different amounts of Li₂CO₃ substitutions. High electrical properties of d₃₃ = 167 pC/N, k_p = 0.34, P_r = 40 μC/cm² and E_c = 38 kV/cm were obtained from the specimen containing 0.1 mol% of Li₂CO₃ sintered at 1080 °C.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Investigations on Pr1.6Sr0.4NiO4-YSZ-Ag composite cathode for solid oxide fuel cells

Ag-network was successfully deposited by VA-EP (vacuum assisted electroless plating) method on Pr_1.6Sr_0.4NiO₄-YSZ cathode to form (1−x) wt% Pr_1.6Sr_0.4NiO₄−x wt% YSZ-Ag (x=0, 10, 20, 30, 40) (abbr. PYx-Ag) composite cathode. XRD results suggested that there was a good chemical stability between Pr_1.6Sr_0.4NiO₄ and YSZ at temperatures below 1050 °C. PY20-Ag cathode exhibited higher exchange current density, lower overpotential and ASR (Area Specific Resistance) than PY20 cathode. At 650 °C, the ASR of PY20-Ag cathode was 2.5 Ω cm², which was only about 42% of that of PY20, 5.9 Ω cm². PY20-Ag can be a promising candidate for SOFC cathode.     

Preparation and characterization of CaTiO 3 –(Li 1/2 Nd 1/4 Sm 1/4 )TiO 3 microwave ceramics by a sol–gel combustion process

A novel sol–gel combustion process was adopted to synthesize reactive ceramic powder with composition of 0.25 CaTiO₃–0.75 (Li_1/2Nd_1/4Sm_1/4)TiO₃, and microwave dielectric ceramics were prepared at different sintering temperatures using the synthesized powder. The combustion behavior of citrate gel and the sintering feature of the synthesized powder were evaluated by using differential thermal analysis–thermogravimetric analysis and thermo-mechanical analysis techniques, respectively. The citrate gel exhibits a self-propagating behavior after being ignited in air at room temperature. The as-burnt powder is so highly reactive that it can be transformed into single-phase perovskite at 900 °C and it can be sintered at 1100 °C. The effects of sintering temperature on the density, microstructure, and dielectric properties of the sintered ceramics were investigated. The maximum values of density, dielectric constant, and Q×f were achieved after sintering at 1200 °C. At 1200 °C, very dense ceramics with uniform grains and good dielectric properties with a dielectric constant of 123.8, a Q×f value of 5110 (at 3.7 GHz), and a τ_f value of +12.5 ppm/°C were achieved via the sol–gel combustion route. PACS 77.84.Dy; 81.20.FW; 77.22.-d     

Microstructure-dependent giant dielectric response in CaCu3Ti4O12 ceramics

CaCu₃Ti₄O₁₂ ceramics were prepared at the sintering temperatures ranged from 1025 to 1125 °C, and the dielectric characteristics were evaluated together with the microstructures. The giant dielectric constant with the maximum of 53,120 was obtained in CaCu₃Ti₄O₁₂ ceramics at room temperature and 10 kHz, and strong processing and microstructure dependence of dielectric characteristics of the present ceramics was determined. The precipitation of the dispersed Cu-rich secondary phases of CuO and/or Cu₂O and their network structure provided the extrinsic origins of the enhanced giant dielectric response, and the present findings would offer the greater potential for enhancing the giant dielectric constant and controlling the dielectric loss in CaCu₃Ti₄O₁₂ ceramics by optimizing the microstructures.