Adsorption isotherms for oxygen chemisorbed on silver powder

Adsorption isotherms have been measured on cleaned silver powder from 178 to 339°C at oxygen pressures of 0.226 Pa to 40 kPa using a vacuum ultramicrobalance. Adsorption equilibrium was found at all temperatures and pressures studied. The surface was prepared for the reproducible chemisorption studies using an established method of cyclic outgassing, oxygen adsorption and reduction in carbon monoxide. Seven isotherms were measured that spanned fractional surface coverages from 0.17 to 1.1. The isosteric heat of adsorption q was determined at constant values of θ. After decreasing from 42 to 17.7 kcal mol^?1 at the lower coverages, q remains constant at 18.4 ± 0.8 kcal mol^?1 from θ of 0.33 to about 0.90 and then decreases to zero at the highest coverages and temperatures. The initial drop in q is attributed to the formation of islands of a two-dimensional surface silver oxide. The constant value of q results then from the completion of the oxide layer and molecular adsorption on and/or through the oxide. The decrease in q to zero at the highest coverages results from repulsions in the adlayer at T ≤ 275°C and absorption into silver at T > 302°C.     

Adsorption of gases on a polymer adsorbent MN-200 in the region of supercritical temperatures and pressures

Adsorption of nitrogen, argon, and methane in a polymer adsorbent MN-200 was studied in the pressure range of 0.1–40 MPa at temperatures of 303, 323, 343, and 363 K. The excess adsorption isotherms were measured, the adsorption volumes were determined, the adsorption isotherms of total content and the characteristic adsorption energies were calculated. Isosteric, integral, and average heats of adsorption were determined.

     

Adsorption of fluoride from aqueous solution by acid treated spent bleaching earth

Acid treated spent bleaching earth was studied to assess its capacity for the adsorption of fluoride from aqueous solutions. Adsorption isotherms have been modeled by Langmuir and Freundlich equations and isotherm constants for both isotherms were calculated. The effect of the adsorbent concentration on the adsorption was studied. The dependence of the adsorption of fluoride on the pH of the solution has been studied to achieve the optimum pH-value and a better understanding of the adsorption mechanism. It has been found that maximum adsorption of fluoride from aqueous solutions takes place at pH-value of 3.5. Second-order equation was used to describe the adsorption rate of fluoride and adsorption rate constant was calculated. Intraparticle and mass transfer coefficients were calculated. The influence of addition of the anions on the adsorption of fluoride was also studied to simulate industrial waste waters and the addition of anions decreased the adsorption of fluoride on the acid treated spent bleaching earth (SBE).     

Monte Carlo simulation of n-alkane adsorption isotherms in carbon slit pores

The single component adsorption of alkanes in carbon slit pores was studied using configurational-biased grand canonical Monte Carlo simulations. Wide ranges of temperature, pressure, alkane chain length, and slit height were studied to evaluate their effects on adsorption. Adsorption isotherms and density and orientation profiles were calculated. The behavior of long alkanes at high temperatures was found to be similar to short alkanes at lower temperatures. This suggests that the isotherms may be related through the Polanyi potential theory.     

ADSORPTION OF PHENOL AND NITROPHENOLS ON A HYPERCROSSLINKED POLYMERIC ADSORBENT

1. INTRODUCTION Nitrophenols are versatile raw materials in chemical industry and used in a great diversity of applications such as herbicides, insecticides and bactericides. Due to their extreme toxicity and adverse effect upon human and biota at very l…     

DF01大孔树脂吸附苦参碱过程的研究

以大孔吸附树脂对苦参碱溶液的吸附行为为研究对象，对苦参碱的吸附平衡进行了研究，以Freundlich和Langmuir方程拟合了室温下的吸附等温线，研究结果表明，用Freumdlich方程拟合较理想，同时，还考察了不同因素对吸附过程的影响，并用线性方程式对吸附柱的透过曲线进行了拟合，这对了解床层的吸附行为特征及吸附剂性能有着重要意义。     

Th(IV) adsorption on alumina: effects of contact time, pH, ionic strength and phosphate

Adsorption of Th(IV) (total concentration, 10(-5)-10(-4) mol/L) was studied by a batch technique. The effects of pH, ionic strength, contact time, and phosphate on the adsorption of Th(IV) onto alumina were investigated. Adsorption isotherms of Th(IV) on alumina at approximately constant pH and three ionic strengths (0.05, 0.1, 0.5 mol/L KNO3) were determined. It was found that the pH values of aqueous solutions of both the Th(IV)-alumina and phosphate-alumina adsorption systems increase with increasing contact time, respectively. Adsorption of Th(IV) on alumina steeply increases with increasing pH from 1 to 4.5 and the adsorption edge consists of three regions. The phosphate added clearly enhances Th(IV) adsorption in the pH range 1-4. From the adsorption isotherms at approximately constant pH and three different ionic strengths, a reduced ionic strength effect was observed and is contradictory to the insensitive effect obtained from the adsorption edges on three oxides of Fe, Al, and Si at different ionic strengths. Compared with the adsorption edges at different ionic strengths, the adsorption isotherms at approximately constant pH and different ionic strengths are more advantageous in the investigation of ionic strength effect. The significantly positive effect of phosphate on Th(IV) adsorption onto alumina was attributed to strong surface binding of phosphate on alumina and the subsequent formation of ternary surface complexes involving Th(IV) and phosphate.     

Experimental and Theoretical Study of the Effect of Moisture on Methane Adsorption and Desorption by Activated Carbon at 273.5 K

Adsorption and desorption of methane by activated carbon (AC) at constant temperature and at various pressures were investigated. The effect of moisture was also studied. A volumetric method was used, up to 40 bar, at a temperature of 273.5 K. Results of a dry AC sample were compared with those obtained from a moist sample and two different ACs with different physical and surface properties were used. As expected, the results showed that the existence of moisture, trapped in the AC pores, could lead to a decrease in the amount of methane adsorbed and a decrease in the amount of methane delivered during desorption. To model the experimental results, a large variety of adsorption isotherms were used. The regressed parameters for the adsorption isotherms were obtained using the experimental data generated in the present study. The accuracy of the results obtained from the different adsorption isotherms was favorably compared.     

Studies on manganese nodule leached residues 2. Adsorption of aqueous phosphate on manganese nodule leached residues

Adsorption of phosphate onto manganese nodule leached residues was investigated as a possible alternative to conventional methods of phosphate removal from industrial effluents. Adsorption behaviors were studied as a function of time, temperature, pH, and concentration level of adsorbate and adsorbent in acetic acid-sodium acetate buffer medium. The adsorption of phosphate follows the Langmuir adsorption isotherms. The magnitude of adsorption of phosphate in manganese nodule leached residues was compared with that in naturally occurring Mn nodule. Manganese nodule leached residues show better affinity toward phosphate adsorption.     

Adsorption of hydrogen on multiwalled carbon natotubes at 77 K

Adsorption of H₂ on multiwalled carbon nanotubes was measured at 77 K by a volumetric method. Adsorption and desorption isotherms are largely reversible. The adsorption capacity increased remarkably after receiving heat treatment at 400 °C and being pressed into pellets. The isotherms show typical feature of supercritical adsorption and were satisfactorily modeled by the model that applied for usual supercritical adsorption. The maximal adsorption capacity of hydrogen under the condition tested is less than 0.5 wt%.     

Characteristics of dextrin adsorption by elemental sulfur

Characteristics of dextrin adsorption by elemental sulfur were investigated by the means of diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, total organic carbon (TOC) measurements, BET measurements as well as molecular dynamics simulation (MDS). Adsorption isotherms for dextrin adsorption by sulfur were compared to isotherms for dextrin adsorption by other hydrophilic and hydrophobic surfaces taken from the literature. The three-dimensional structure of dextrin was studied in detail and possible mechanisms of adsorption are discussed. Additionally, molecular dynamics simulations provided further insight into the mechanism of dextrin adsorption by elemental sulfur.     

Adsorption of Amino Acids on Cellulose Diacetate Membranes

Adsorption of a series of amino acids on cellulose diacetate membranes was studied. Adsorption isotherms were constructed and thermodynamic characteristics of adsorption (chemical potential of the adsorbent and Gibbs energy) were determined.     

Adsorption of Cu(II), Zn(II), Ni(II), Pb(II), and Cd(II) from aqueous solution on Amberlite IR-120 synthetic resin

The adsorption of copper(II), zinc(II), nickel(II), lead(II), and cadmium(II) on Amberlite IR-120 synthetic sulfonated resin has been studied at different pH and temperatures by batch process. The effects of parameters such as amount of resin, resin contact time, pH, and temperature on the ion exchange separation have been investigated. For the determination of the adsorption behavior of the resin, the adsorption isotherms of metal ions have also been studied. The concentrations of metal ions have been measured by batch techniques and with AAS analysis. Adsorption analysis results obtained at various concentrations showed that the adsorption pattern on the resin followed Freundlich isotherms. Here we report the method that is applied for the sorption/separation of some toxic metals from their solutions.     

Quartzite an efficient adsorbent for the removal of anionic and cationic dyes from aqueous solutions

Quartzite obtained from local source was investigated for the removal of anionic dye congo red (CR) and cationic dye malachite green (MG) as an adsorbent from aqueous solution in batch experiment. The adsorption process was studied as a function of dye concentration, contact time, pH and temperature. Adsorption process was described well by Langmuir and Freundlich isotherms. The adsorption capacity remained 666.7 mg/g for CR dye and 348.125 mg/g for MG dye. Data was analyzed thermodynamically, ΔH⁰ and ΔG⁰ values proved that adsorption of CR and MG is an endothermic and spontaneous process. Adsorption data fitted best in the pseudo-first order kinetic model. The adsorption data proved that quartzite exhibits the best adsorption capacity and can be utilized for the removal of anionic and cationic dyes.     

The removal and kinetic study of Mn,Fe, Ni and Cu ions from wastewater onto activated carbon from coconut shells

Activated carbon from coconut shells (ACCS) was synthesised and used for the removal of metal ions (manganese, iron, nickel and copper) from aqueous solutions. Two different adsorption models were used for analysing the data. Adsorption capacities were determined: copper ions exhibited the greatest adsorption on activated carbon obtained from coconut shells because of their size and pH conditions. Adsorption capacity varied as a function of the pH. Adsorption isotherms from aqueous solutions of heavy metals on ACCS were determined and were found to be consistent with Langmuir’s adsorption model. Adsorbent quantity and immersion enthalpy were studied. The results were compared with other adsorbents used in a prior study.     

Adsorption of human serum albumin (HSA) onto colloidal TiO2 particles, Part I

The adsorption of human serum albumin (HSA) onto colloidal TiO2 (P25 Degussa) particles was studied in NaCl electrolyte at different solution pH and ionic strength. The HSA-TiO2 interactions were studied using adsorption isotherms and the electrokinetic properties of HSA-covered TiO2 particles were monitored by electrophoretic mobility measurements. The adsorption behavior shows a remarkable dependence of the maximum coverage degree on pH and was almost independent of the ionic strength. Other characteristic features such as maximum adsorption values at the protein isoelectric point (IEP approximately 4.7) and low-affinity isotherms that showed surface saturation even under unfavorable electrostatic conditions (at pH values far away from the HSA IEP and TiO2 PZC) were observed. Structural and electrostatic effects can explain the diminution of HSA adsorption under these conditions, assuming that protein molecules behave as soft particles. Adsorption reactions are discussed, taking into account acid-base functional groups of the protein and the surface oxide in different pH ranges, considering various types of interactions.     

Adsorption of benzoic acid onto high specific area activated carbon cloth

The adsorption of benzoic acid from aqueous solution onto high area carbon cloth at different pH values has been studied. Over a period of 125 min the adsorption process was found to follow a first-order kinetics and the rate constants were determined for the adsorption of benzoic acid at pH 2.0, 3.7, 5.3, 9.1, and 11.0. The extents of adsorption and the percentage coverage of carbon cloth surfaces were calculated at 125 min of adsorption. Adsorption isotherms at pH values of 2.0, 3.7, and 11.0 were derived at 25 degrees C. Isotherm data were treated according to Langmuir and Freundlich equations and the parameters of these equations were evaluated by regression analysis. The fit of experimental isotherm data to both equations was good. It was found that both the adsorption rate and the extent of adsorption at 125 min were the highest at pH 3.7 and decreased at higher or lower pH values. The types of interactions governing in the adsorption processes are discussed considering the surface charge and the dissociation of benzoic acid at different pH values.     

Adsorption and dissociation equilibrium of benzoic acid on the mercury electrode

Adsorption of benzoic acid at the mercury electrode was studied in a wide pH range. The adsorption isotherms of benzoic acid from electrocapillary and capacity measurements were calculated. From the dependence of capacitance and potential of zero charge on pH the pK_el of benzoic acid was determined.     

Kinetic and isotherm studies of Cu(II) adsorption onto H3PO4-activated rubber wood sawdust

Adsorption of Cu(II) from aqueous solution onto H(3)PO(4)-activated carbon using rubber wood sawdust (RSAC) was investigated in a batch system. Kinetic and isotherm studies were carried out by considering the effects of various parameters, such as initial concentration, contact time, pH, and temperature. The optimal pH value for Cu(II) adsorption onto RSAC was found to be 6.0. Thermodynamic parameters such as standard Gibbs free energy (DeltaG(0)), standard enthalpy (DeltaH(0)), and standard entropy (DeltaS(0)) were evaluated by applying the Van't Hoff equation. The thermodynamics of Cu(II) adsorption onto RSAC indicates its spontaneous and exothermic nature. Langmuir, Freundlich, and Temkin isotherms were used to analyze the equilibrium data at different temperatures. The Langmuir isotherm fits the experimental data significantly better than the other isotherms. Adsorption kinetics data were tested using pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. Kinetic studies showed that the adsorption followed a pseudo-second-order reaction. The initial sorption rate, pseudo-first-order, pseudo-second-order, and intraparticle diffusion rate constants for different initial concentrations were evaluated and discussed. Adsorption mechanism studies revealed that the process was complex and followed both surface adsorption and particle diffusion. The rate-controlling parameter and effective diffusion coefficient were determined using the Reichenberg plot. It was found that the adsorption occurs through film diffusion at low concentrations and at higher concentration the particle diffusion becomes the rate-determining step.     

Adsorption Isotherm Studies on Titanium Carbide Powders

We have used adsorption isotherms to perform a comparative study of the substrate quality of five groups of titanium carbide powder, manufactured following different procedures. The isotherms were measured in an automated setup at 77.3 K using methane and argon as the adsorbates. We determined the specific surface area of each of the powders studied. We also determined whether or not there was evidence of steps (indicative of layer-by-layer adsorption) in each set of adsorption data. The isothermal compressibilities of the adsorbed films were determined from the data measured for each sample. Adsorption measurements were also conducted to determine the effect that heating the powders under vacuum had on the resulting substrate quality.