冠醚络合高活性双金属氰化物制备及CO_2与环氧丙烷共聚（英文）

首次在共沉淀过程中添加18-冠-6醚络合生成的钾离子得到了均一的高活性冠醚络合的锌-钴双金属催化剂,并用红外光谱(FTIR)、扫描电镜(SEM)、热重红外(TGA-IR)和X射线衍射(XRD)进行了表征.元素分析发现K含量为1.2%.FTIR表明未加冠醚络合的双金属催化剂离心后上下部分呈现不同的络合状态,而冠醚络合的双金属催化剂仍保持均一.SEM表明冠醚络合的双金属催化剂为均一松散的结构.由于生成的钾离子被冠醚络合,不影响聚合反应效果.TGA-IR表明冠醚不仅络合K离子,还参与对金属活性中心的络合.XRD表明此催化剂具有低的结晶度.所制冠醚络合的锌-钴双金属催化剂能成功催化CO2与环氧丙烷共聚,其中CDMC3催化得到的共聚物碳酸酯含量为47.8%,副产物环状碳酸酯为1.5%,催化效率高达5122 g/g催化剂(32600 g/g Zn),明显优于不添加冠醚以同样工艺制备的DMC1(共聚物碳酸酯含量29.2%,副产物环状碳酸酯3.3%,催化效率4100 g/g催化剂(16300g/g Zn).与不添加冠醚8次洗涤离心得到的DMC2相当(共聚物碳酸酯含量48.3%,副产物环状碳酸酯含量2.4%,催化效率5073 g/g催化剂(16400 g/g Zn)).基于此结果提出了两步的反应机理假设.     

双金属氰化物/稀土配合物催化二氧化碳和环氧丙烷的共聚合

使用双金属氰化物/稀土配合物复合催化剂催化二氧化碳和环氧丙烷共聚合,其催化效率比双金属氰化物催化剂有显著提高,得到了数均相对分子质量大于1.0×105的聚合物。研究了复合催化剂的组成(如稀土的种类、稀土与锌的比例(Ln/Zn)、稀土配合物中酸根离子的酸性等)对共聚反应的影响,同时研究了反应体系的压力及反应时间对催化活性的影响。采用Y(CCl3COO)3稀土金属配合物有利于共聚反应的进行。当n(Y)/n(Zn)=6、聚合4 h后,其催化活性比单纯的双金属氰化物提高了31.5%,聚合物的相对分子质量则没有太大变化,而副产物碳酸丙烯酯的质量分数低于2%,而在该温度下单独采用稀土三元催化剂时副产物碳酸丙烯酯的生成量通常在10%以上。聚合物中碳酸酯含量低于双金属氰化物的催化产物,说明稀土配合物只是起到活化金属与环氧丙烷配位的作用,没有提高共聚物的碳酸酯含量,整个共聚合反应依然遵循双金属氰化物催化的共聚反应机理。     

锌-钴双金属氰化络合物催化二硫化碳与氧化环己烯共聚研究

报道了锌-钴双金属氰化络合物(double metal cyanide complex,DMCC)催化CS2与氧化环己烯(CHO)直接共聚生成脂环族聚硫代碳酸酯的反应.傅立叶红外光谱(FTIR)及拉曼(Raman)光谱结果表明该共聚物端基为-OH和-SH结构;核磁共振(1H和13C-NMR)结果表明共聚物主链含碳酸酯-O(CO)O-链节和4种硫代碳酸酯-O(CO)S-、-S(CO)S-、-O(CS)S-和-S(CS)S-链节结构;气相色谱-质谱(GC-MS)联用结果表明产物中含有环硫环己烷及3种环状硫代碳酸酯.聚合物链结构和产物种类表明CS2/CHO共聚反应存在氧-硫原子交换反应过程.     

SalenAl(O~iPr)催化CO_2与氧化环己烯共聚及影响因素研究

以SalenAl(OiPr)为催化剂,分别加入各种路易斯碱作为共催化剂催化二氧化碳与氧化环己烯共聚,发现共聚催化效率与共催化剂的供电子能力有关.分别研究催化剂浓度、共催化剂的用量、反应时间、反应温度、CO2压力等各种因素对该共聚反应的影响,发现SalenAl(OiPr)浓度为2 g/L时,以等摩尔量的二甲氨基吡啶(DMAP)作为共催化剂,在4 MPa的CO2和80℃下反应32 h,可得到碳酸酯键含量>99%的共聚产物,其催化效率高达495 g/g,13C-NMR检测表明共聚物为无规立构聚合物,GPC测得分子量Mn为55900,分子量分布比较窄(PDI=1.32).DSC得到共聚物的玻璃化转变温度为136℃,热重分析(TGA)可以看出共聚物在350℃可完全分解,具有优良的热分解性.     

Zn-Co双金属氰化络合物催化氧化环己烯/二氧化碳共聚反应

 制备了基于Zn3［Co(CN)6］2的双金属氰化络合物催化剂,考察了其催化氧化环己烯/CO2共聚反应的特点,以及制备过程中有机配体和卤化锌种类对催化剂催化性能和共聚产物组成的影响. 结果表明,该催化剂能高效催化共聚反应,在催化剂含量为1.8×10-4时其催化效率可达6?000 g/g以上, FT-IR和 1H NMR表征证实聚合产物为接近交替的共聚物. 催化剂催化效率受有机配体和卤化锌种类影响,但共聚物组成只受卤化锌种类影响,而不受有机配体种类影响,其中叔丁醇和ZnCl2分别是较好的有机配体和锌盐. 动力学研究表明,该共聚反应对催化剂浓度是一级反应,反应的平均活化能为41.6 kJ/mol.     

溴化锌-卤化正四丁基铵高效催化合成苯乙烯环状碳酸酯

溴化锌-卤化正四丁基铵二元催化剂高效催化合成苯乙烯环状碳酸酯, 当n-Bu4NI/ZnBr2摩尔比为2时, 在短时间内(30 min)可将苯乙烯环氧化物几乎完全转化为环状碳酸酯, 无其它副产物的生成. 在ZnBr2/n-Bu4NX的催化体系中加入Au/SiO2 氧化催化剂时, 能将苯乙烯直接氧化, 然后碳酰化实现“一锅法”制备环状碳酸酯. 在此合成路线中担载的纳米金催化第一步苯乙烯环氧化反应; ZnBr2/n-Bu4NBr催化第二步CO2环加成反应. 在温和的反应条件下(80 ℃, 1 MPa, 4 h)将环状碳酸酯的产率提高到42%.     

微量酸酐诱导增强的二氧化碳/环氧氯丙烷共聚反应

环氧氯丙烷(ECH)与二氧化碳(CO₂)的共聚反应产物具有可修饰的C―Cl键,是实现聚碳酸酯功能化的有效途径,然而该反应一直受制于较长的诱导期.本文提出了一种酸酐诱导增强共聚反应活性的策略,即在CO₂/ECH共聚体系中引入微量环状酸酐以缩短诱导期,提高反应活性.以锌钴氰化络合物(DMC)催化剂为例,在CO₂/ECH共聚体系中仅加入0.1 mol%的不同种类环状酸酐,ECH转化率可达到23.6%～83.6%(40℃,24 h),相比于未添加酸酐体系的低转化率(2.6%),反应活性显著增强.尤其是5-降冰片烯-2,3-二羧酸酐诱导的CO₂/ECH共聚体系显示出最高的活性增强效应,在28 h内ECH转化率可达98.8%,催化效率为430 g polymer/g cat.,并保持91.3 wt%的聚合物选择性,进而制备出碳酸酯单元含量为68.2%、分子量为16.7 kg/mol的CO₂基聚碳酸酯.进一步采用在线红外等光谱分析技术,证实环状酸酐优先与ECH发生共聚反应生成聚酯活性种是缩短...     

稀土三元催化体系ZnO/SiO_2负载化及季铵盐催化CO_2与环氧丙烷合成高分子量聚碳酸酯（英文）

由环氧丙烷(PO)和CO_2交替共聚合成脂肪族聚碳酸亚丙酯,CO_2利用率高,所得产物具有一定的力学性能和生物降解性能,具有广泛应用前景.目前,用于CO_2和环氧化合物共聚的催化体系主要包含锌、钴、镉、铬、铝和稀土等金属活性中心,结构、活性各异的催化剂体系,其催化性能和产物性能也各具特色.其中,稀土三元催化剂(ZnEt_2-甘油-三氯乙酸钇)因合成聚碳酸酯产物的分子量高、碳酸酯单元含量高、聚醚及环碳酸酯副产物少的特点而受到关注.但是由于催化剂催化效率低,聚合时间长,产品成本高,使得工业化规模生产受到限制.本文基于稀土三元催化体系,将催化剂负载于硅胶及锌改性硅胶,优化了其制备条件,同时考察了添加季铵盐对催化CO_2/环氧丙烷共聚合成聚碳酸酯性能的影响.结果表明,在1 L聚合釜中,于3.5 MPa和70 ℃反应条件下,ZnO担载量及ZnO/SiO_2添加量对反应性能均有影响.当3 wt%ZnO/SiO_2的添加量为5 g时,稀土三元催化体系的活性为4845.2 g/mol_(Zn).所得聚合物经过多次纯化处理后,能够有效提高材料的热学性能,即有效除去产物中的ZnO对聚合物的热稳定性有重要作用.添加含有不同阴离子(F~-,Cl~-和Br~-)的季铵盐可显著影响稀土三元催化剂的活性.其中,仅四甲基氟化铵可以明显提高反应活性乃至聚合物分子量.在3 wt%ZnO/SiO_2载体和四甲基氟化铵的协同作用下,稀土三元催化体系的共聚性能明显提升,活性最高可达5223.0 g/mol_(Zn).聚合物结构分析表明,在载体和四甲基氟化铵存在下,聚合物分子量明显提高,可达到20万以上,分子量分布明显变窄,且聚合物结构如碳酸酯的单元含量、副产物含量以及聚合物产品玻璃化温度基本不变,后者均保持在40.41℃.基于此,我们提出了在ZnO改性硅胶载体及四甲基氟化铵存在下稀土三元催化体系催化CO_2/环氧丙烷共聚的反应机理:ZnO/SiO_2载体有利于稀土三元催化体系的分散,而四甲基氟化铵则有利于吸附在ZnEt_2上的环氧丙烷开环     

稀土三元催化体系ZnO/SiO2负载化及季铵盐催化CO2与环氧丙烷合成高分子量聚碳酸酯

由环氧丙烷(PO)和CO2交替共聚合成脂肪族聚碳酸亚丙酯,CO2利用率高, 所得产物具有一定的力学性能和生物降解性能, 具有广泛应用前景. 目前, 用于CO2和环氧化合物共聚的催化体系主要包含锌、钴、镉、铬、铝和稀土等金属活性中心, 结构、活性各异的催化剂体系, 其催化性能和产物性能也各具特色. 其中, 稀土三元催化剂(ZnEt2-甘油-三氯乙酸钇)因合成聚碳酸酯产物的分子量高、碳酸酯单元含量高、聚醚及环碳酸酯副产物少的特点而受到关注. 但是由于催化剂催化效率低, 聚合时间长, 产品成本高, 使得工业化规模生产受到限制.本文基于稀土三元催化体系, 将催化剂负载于硅胶及锌改性硅胶, 优化了其制备条件, 同时考察了添加季铵盐对催化CO2/环氧丙烷共聚合成聚碳酸酯性能的影响. 结果表明, 在1 L聚合釜中, 于3.5 MPa和70 oC反应条件下, ZnO担载量及ZnO/SiO2添加量对反应性能均有影响. 当3 wt% ZnO/SiO2的添加量为5 g时, 稀土三元催化体系的活性为4845.2 g/molZn..所得聚合物经过多次纯化处理后, 能够有效提高材料的热学性能, 即有效除去产物中的ZnO对聚合物的热稳定性有重要作用. 添加含有不同阴离子(F- , Cl- 和Br- )的季铵盐可显著影响稀土三元催化剂的活性. 其中, 仅四甲基氟化铵可以明显提高反应活性乃至聚合物分子量. 在3 wt% ZnO/SiO2载体和四甲基氟化铵的协同作用下, 稀土三元催化体系的共聚性能明显提 升, 活性最高可达5223.0 g/molZn. 聚合物结构分析表明, 在载体和四甲基氟化铵存在下, 聚合物分子量明显提高, 可达到20万以上, 分子量分布明显变窄, 且聚合物结构如碳酸酯的单元含量、副产物含量以及聚合物产品玻璃化温度基本不变, 后者均保持在40-41 ?C. 基于此, 我们提出了在ZnO改性硅胶载体及四甲基氟化铵存在下稀土三元催化体系催化CO2/环氧丙烷共聚的反应机理: ZnO/SiO2载体有利于稀土三元催化体系的分散, 而四甲基氟化铵则有利于吸附在ZnEt2上的环氧丙烷开环.     

季铵盐和叔胺协同催化一步酯交换法合成碳酸二甲酯的研究

以不同季铵盐和叔胺为催化剂,考察了它们各自和协同催化甲醇、CO2和环氧丙烷(PO)或环氧氯丙烷(ECH)一步法合成碳酸二甲酯(DMC)的催化性能。结果表明,季铵盐对一步法合成DMC中第一步反应(即CO2和PO环加成反应生成环状碳酸酯)的催化性能较好,而叔胺对一步法合成DMC中第二步反应(即环状碳酸酯与甲醇反应生成DMC)的催化效果较好。其中,以双十六烷基二甲基溴化铵(DHDMAB)和N,N-二烯丙基甲基胺(MDAA)分别为季铵盐和叔胺的协同催化性能最佳,其DMC产率达35.2%。此外,以PO为环氧化合物的DMC产率远高于ECH。     

Allylation of phenoxides by crown ethers and their polymers

Allylation of sodium phenoxide in the presence of crown ethers produces a high ratio of O/O + C allylation when conducted in water, phenol, benzene, or diethyl ether. The striking increase in the product ratios is attributed to specific complexation of the crown ethers that facilitate the dissociation of the ion pair aggregate of the sodioderivative in benzene or diethyl ether. The crown ethers may act as a phase transfer catalyst when the reaction is run in water. Furthermore, the O/O + C ratios of the allylation strongly depend on the kind of crown ethers used. To examine their effect the allylation of sodium phenoxide was studied with various crown ethers, such as 18-crown-6, benzo-18-crown-6, benzo-15-crown-5, poly(vinylmonobenzo-15-crown-5), and poly(vinylmono-benzo-18-crown-6), as catalysts. It was found that among these crown ethers poly(vinylmono-benzo-15-crown-5) was the most effective catalyst.     

Crown-Ether Phase-Transfer Catalysts for Reduction of Ketones,Oxidation of Olefins and Polymerization of p-Xylenedibromide

Various homogeneous and heterogeneous crown ether catalysts were prepared and applied as phase transfer catalysts for some reductions, oxidations and polymerizations. Among various crown ethers, 15-crown-5 seems the best to catalyze the reduction of ketones and aldehydes with sodium borohydride in nonpolar aprotic solvents. A granular entrapped 15-crown-5-polyacrylamide catalysts was also prepared and applied as a heterogeneous catalyst for these reductions which seem to obey pseudo-first-order kinetics with rate constant 10^?4–10⁵ s^?1. The steric effects of ketones and the effects of temperature and concentration of crown ethers, sodium borohydride and carbonyl compounds were also investigated. Among various crown ethers, 18-crown-6 is the best to catalyze the oxidation of olefins such as styrene, xylene and stilbene with potassium permanganate. Crown ethers were successfully applied as catalysts for anionic polymerization of p-xylenedibromide with sodium dithionite as an initiator.     

Phase-transfer catalytic activity of soluble polystyrenes containing crown ether moieties and hydroxyl groups adjacent to the macrorings

Soluble polystyrenes with crown ether structures and hydroxyl groups adjacent to the macrorings were prepared by the reaction of epoxide-containing polystyrenes with monoaza-15-crown-5 or monoaza-18-crown-6. Rate of formation of the polymer-bound alkali cation-crown alkoxide ion pair from the soluble polystyrenes and aqueous NaOH or KOH depended on the loading of crown ether and hydroxyl units and on the size of the macroring. The elimination of HCl from less reactive 2-chloroethylbenzene with aqueous NaOH or KOH in the presence of the soluble polystyrene catalysts under two-phase conditions was limited mainly by the intrinsic reaction rate. The elimination of HBr from more reactive 2-bromoethylbenzene in the presence of the less (11%) ring-substituted polymer catalyst with 18-crown unit was limited by the alkoxide formation rate. © 1994 John Wiley & Sons, Inc.     

A novel thermoresponsive hydrogel with ion-recognition property through supramolecular host-guest complexation

A novel thermoresponsive hydrogel with ion-recognition property was prepared via free-radical cross-linking copolymerization of N-isopropylacrylamide (NIPAM) with benzo-18-crown-6-acrylamide (BCAm) as host receptor. Both chemical structures and stimuli-sensitive properties of the prepared poly(N-isopropylacrylamide-co-benzo-18-crown-6-acrylamide) P(NIPAM-co-BCAm) hydrogel were characterized. The smart hydrogel could respond to both temperature and ion stimuli. When the crown ether units captured Ba2+ and formed stable BCAm/Ba2+ host-guest complexes, the lower critical solution temperature (LCST) of the hydrogel increased due to the repulsion among charged BCAm/Ba2+ complex groups and osmotic pressure within the hydrogel. Whereas crown ethers captured Cs+, the LCST shifted to a lower temperature because of the formation of 2:1 sandwich complexes. Unexpectedly, the LCST of the cross-linked P(NIPAM-co-BCAm) hydrogel in K+ solution did not shift to a higher temperature, which was definitely different from the previously reported linear P(NIPAM-co-BCAm) copolymer in K+ solution. The results of this work provide valuable information for development of dual thermo- and ion-responsive hydrogels which have potential applications in drug controlled-release systems or biomedical fields.     

冠醚共缩聚物的合成与性能

双冠醚化合物对某些金属离子比单冠醚具有更好的络合性能和选择性,它们合成、应用研究越来越受到人们的重视,本工作采用2,6-二羟甲基对甲氧基苯酚为缩合剂与芳香族冠醚缩聚,得到一系列具有双冠醚结构特征的新酚醛型聚苯并冠醚(简称聚冠醚),聚冠醚合成容易,并呈现了比相应单冠醚更优越的络合萃取能力和富集效率。     

1^H、7^Li、23^Na、133^Cs NMR研究含氮大环醚双内酯和大环胺双内酰胺的配合性能

本文报道1^H、7^Li、23^Na、133^Cs NMR测定N, N'-二羧甲基大环醚双内酯(1-4)和大环胺双内酰胺(5), N-对甲苯磺酰基大环醚双内酯(6, 7), 4'-丹磺酰氨基苯并-18-冠-6(8)与Li^+、Na^+、K^+、Cs^+、Cd^2+和Pb^2+金属离子的配位作用, 并以非线性最小二乘法拟合计算了配合物的形成常数; 同时, 发展了一种用133^Cs NMR测量冠醚和碘离子竞争配合Cs^+的配合物形成常数的新技术。     

Dibenzotetraaza crown ethers: a new family of crown ethers based on o-phenylenediamine

Dibenzotetraaza (DBTA) crown ethers possess two o-phenylenediamine moieties. They are homologues of dibenzo crown ether phase-transfer catalysts and were prepared from the condensation of benzimidazoles with oligo(ethyleneglycol) dichlorides and oligo(ethyleneglycol) ditosylates. Compounds with ring sizes ranging from 18-crown-6 to 42-crown-14 were prepared. In addition, various altered benzimidizoles were used to produce DBTA crown ethers with modified substituents and ether bridges, as well as benzimidazolidine crown ethers. The synthetic approach presented here proved to be a convenient route to a new family of crown ethers with overall yields of up to 48% based on the benzimidazole. Yields for the ring-closing step were generally high, ranging from 51% to 94%, without the need for high-dilution conditions. Reaction of the DBTA crown ethers with alkyl and benzyl halides was found to be a facile way to obtain the corresponding tetra(N-organyl) compounds. Picrate extraction studies were carried out to determine phase-transfer catalytic capabilities. Extraction efficiencies for alkali-metal ions were lower than those for dibenzo-18-crown-6. Efficiencies were higher for other metal ions, with some selectivity for Pb(2+). Tetra(N-methyl) DBTA-18-crown-6 generally exhibited higher extraction efficiencies than its N-H analogue, but the selectivity was lower.     

Interfacial behavior of phase transfer catalysis of the reaction between potassium thiocyanate and p-nitrobenzyl bromide with crown ethers as catalysts

A very simple and novel method is devised to study the mechanism of phase transfer catalysis (PTC) for a nucleophilic substitution reaction between potassium thiocyanate and p-nitrobenzyl bromide (p-NB); the mechanism of the nucleophilic substitution reaction is illustrated by characterizing the interfacial dilational viscoelastic properties of the crown ether catalysts and intermediates, which are closely related to the interfacial behavior of the species in the PTC reaction. The results obtained from this study can be used to infer the mechanism of the nucleophilic substitution reaction that uses 18-crown-6 (18C6) and dibenzo-18-crown-6 (DB18C6) as phase transfer catalysts. This mechanism begins with formation of the intermediates [K · Crown ether]⁺ and [K · Crown ether]⁺SCN^? through mutual collisions between crown ethers and KSCN in the aqueous phase near the interface. Then the complex, [K · Crown ether]⁺Br^?, was obtained due to the collision between [K · Crown ether]⁺SCN^? and p-NB in the organic phase near the interface and simultaneously the products were obtained.     

Crown ether molecular complexes with urea and thiourea

Crystalline complexes of urea and thiourea with crown ethers, have been prepared, viz., 18-crown-6 (18C6), benzo-18-crown-6 (B18C6), dibenzo-18-crown-6 (DB18C6), dicyclohexano-18-crown-6 (DC 18C6) and dibenzo-24-crown-8 (DB24C8). While the complexes of the large ring size crown ether, DB24C8, have high ether to (thio)urea ratios, the stoichiometry of the others lies between one molecule of crown ether and from one to six molecules of (thio)urea. An IR spectral study of the urea and thiourea complexes showed that the behavior of thiourea in these complexes is clearly different from that of urea, indicating the role of sulphur in the interaction of thiourea with crown ethers. The urea and thiourea complexes were classified according to their stoichiometries and their IR spectral behavior into three classes for which credible structures were proposed.     

Cooperative self-assembly and molecular binding behavior of cyclodextrin-crown ether conjugates mediated by alkali metal ions

In order to quantitatively investigate their molecular binding ability, a series of cyclodextrin-crown ether conjugates containing beta-cyclodextrin (beta-CyD) and crown ether units, i.e.N-(benzoaza-15-crown-5)acylaminomethylene tethered 6-diethylenetriamino-6-deoxy-beta-CyD, N-(benzoaza-15-crown-5)acylaminomethylene tethered 6-triethylenetetraamino-6-deoxy-beta-CyD and 4',5'-dimethylene-benzo-15-crown-5 tethered 6-diethylenetriamino-6-deoxy-beta-CyD, have been prepared as ditopic molecular receptors. Their inclusion complexation behavior with four representative fluorescent dyes, i.e. ammonium 8-anilino-1-naphthalenesulfonate (ANS), sodium 6-toluidino-2-naphthalenesulfonate (TNS), acridine red (AR) and rhodamine B (RhB), has been comprehensively investigated in aqueous NaH2PO4/Na2HPO4 or KH2PO4/K2HPO4 buffer solution (pH 7.20) by means of circular dichroism, fluorescence, and 2D NMR spectra. The results indicate that the self-assembly of crown ether modified beta-CyD mediated by potassium ion exhibits a dimeric structure, which significantly enhances the original binding ability and molecular selectivity of parent beta-CyD and its derivatives towards guest molecules through the cooperative binding of two hydrophobic CyD cavities with one guest. This cooperative binding mode of K+/CyD-crown ether systems are further confirmed by Job's experiments and 2D NMR investigations. Attributed to the positive contributions from the metal-ligated crown ether cap and K+-mediated dimerization of CyDs, the binding constant (Ks) values of CyD-crown ether conjugates toward ANS are 10-83 times higher than that of beta-CyD. The increased binding ability and molecular selectivity of CyD-crown ether conjugates are discussed from the viewpoints of size/shape-fit and multiple recognition mechanism.