Study on highly visible light active Bi-doped TiO2 composite hollow sphere

Bi-doped hollow titania spheres were prepared using carbon spheres as template and Bi-doped titania nanoparticles as building blocks. The Bi-doped titania nanoparticles were synthesized at low temperature. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The effects of Bi content on the physical structure and photocatalytic activity of doped hollow titania sphere samples were investigated. Results showed that there was an optimal Bi-doped content (4%) for the photocatalytic degradation of methylene blue (MB).     

Preparation, characterization and photocatalytic activity of the neodymium-doped TiO2 hollow spheres

Nd-doped titania hollow spheres were prepared using carbon spheres as template and Nd-doped titania nanoparticles as building blocks. The Nd-doped titania nanoparticles were synthesized at low temperature. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectrum (DRS). The effects of Nd content on the physical structure and photocatalytic activities of doped titania hollow sphere samples were investigated. Results showed that there was an optimal Nd-doped content (3.9 at.%) for the photocatalytic degradation of dye X-3B (C.I. Reactive Red 2). The apparent rate constant of the best one was almost 9 times as that of P25 titania. The mechanism of photocatalytic degradation of dyes under visible light irradiation was also discussed.     

Synthesis of fluorine-doped titania-coated activated carbon under low temperature with high photocatalytic activity under visible light

Fluorine-doped anatase titania sols were synthesized by hydrolysis of titanium-n-butoxide in the presence of abundant acidic aqueous solution and using ammonium fluoride as fluorine precursors, under mild condition. The prepared fluorine-doped titania nanoparticles were loaded on activated carbon in a rotatory evaporator under vacuum to form a composite photocatalyst. X-ray diffraction, Fourier transform infrared spectrum analysis, UV-visible spectroscopy, scanning electron microscope and Brunauer-Emmett-Teller adsorption measurement were used to characterize these as-prepared powders. The photocatalytic activity of the sample was evaluated by degrading phenol under visible light. Results showed that the composite photocatalyst was porous due to its nano-microstructure. The number of hydroxyl groups on the titania surface was enhanced after fluorine doping. Compared with pure titania-activated carbon and Degussa P25, the as-prepared composite powders exhibited much higher photocatalytic activity, although absorption response range into the visible region was not detected by diffuse reflection spectra.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Ti<Superscript>3+</Superscript>-doped TiO<Subscript>2</Subscript> hollow sphere with mixed phases of anatase and rutile prepared by dual-frequency atmospheric pressure plasma jet

A novel method of synthesizing Ti³⁺-doped TiO₂ was proposed. Ti³⁺-doped TiO₂ hollow spheres were prepared with different thickness of carbon shell by using atmospheric pressure plasma jet generated by dual-frequency power sources. The as-synthesized Ti³⁺-doped TiO₂ hollow microspheres were characterized by X-ray diffraction (XRD) pattern, scanning electron microscope (SEM) images, high-resolution transmission electron microscopy (HRTEM) images, Raman spectra, X-ray photoelectron spectroscopy (XPS), and UV–vis spectra. These results indicated that these samples had mixed phases of anatase and rutile and the structure of hollow sphere varied with different thickness of carbon shell. The Ti-O-C chemical bond was the connection between the TiO₂ hollow sphere and carbon layer. Amount of Ti³⁺ ions were found, which were accompanied with the formation of oxygen vacancies. Meantime, the as-synthesized catalysts also display strong absorption in the visible light region and have a narrow band energy gap. Optical emission spectroscopy (OES) was used to observe different excited species in the discharge area. These results showed that the oxygen content had a significant impact on the number of oxygen vacancies. Finally, the photocatalytic activities of as-prepared samples were evaluated by decomposition of rhodamine B aqueous solution, which showed better photocatalytic activity under UV–vis light irradiation.     

Synthesis, characterization and antibacterial action of hollow titania spheres

Hollow titania spheres were synthesized using the cationic polystyrene lattices which were prepared by polymerization in suspension of styrene using 2,2′-azobis (2-methylpropionamidine) dihydrochloride (AMPA) as an initiator. These cationic colloidal particles were dispersed in absolute ethanol in the presence of poly(vinylpyrrolidone) (PVP), solution of sodium chloride (NaCl) and mixed with ethanolic solutions of titanium tetraisopropoxide (TTIP). Subsequently, hollow spheres of titania compounds were obtained by calcinations of the so-coated polystyrene lattices at elevated temperature in air. The hollow titania spheres were characterized with scanning electron microscopy (SEM), FT-infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Moreover, antibacterial action of illuminated hollow titania spheres on pure culture of Escherichia coli (E. coli) was studied. A decrease of E. coli concentration was observed after illumination of bacteria in the presence of hollow titania spheres.     

Synthesis, characterization and photodegradation study of mixed-phase titania hollow submicrospheres with rough surface

Titania hollow submicrospheres with mixed phase (anatase-brookite or anatase-rutile) were synthesized via the combination of hydrothermal treatment and calcination of submicrospheres consisting of a polystyrene core and an amorphous TiO₂ shell. After hydrothermal treatment, amorphous titania shell could be transformed to anatase-brookite shell consisting of loose packed titania nanocrystals, which could be further converted to anatase-brookite (below 700 °C) or anatase-rutile titania (700-800 °C) hollow spheres with rough surface via calcination. The loose packing of titania nanocrystals not only inhibited the transformation temperature from anatase to rutile, but also provided titania hollow submicrospheres with high photodegradation activity of Rhodamine B. The photocatalytic activity of titania hollow spheres increased firstly then decreased when the calcination temperature was varied in the range of 450-800 °C, while hollow spheres obtained via calcinating at 700 °C exhibited the highest photocatalytic activity, which was five times higher than that of counterpart without hydrothermal treatment.     

C自掺杂TiO2纳米棒的制备与光催化性能研究

本文以TiC为前驱体和掺杂源,采用一步水热法合成了具有可见光吸收的C自掺杂金红石相TiO2纳米棒．样品的结构、形貌、化学态和光学性质等可通过X射线衍射仪（XRD）、扫描电子显微镜（SEM）、傅里叶变换红外光谱仪（FT-IR）、X射线光电子能谱仪（XPS）以及紫外可见分光光度计（UV-vis）来表征．所合成的样品具有较强的光催化活性,可通过在可见光照射下降解有机染料罗丹明B（RhB）来验证．C自掺杂TiO2所呈现的较强光催化活性是由于其具有小的能带间隙（2.74 eV）、大的比表面积和高的电子-空穴对分离率．     

C自掺杂TiO2纳米棒的制备与光催化性能研究

本文以TiC为前驱体和掺杂源,采用一步水热法合成了具有可见光吸收的C自掺杂金红石相TiO2纳米棒．样品的结构、形貌、化学态和光学性质等可通过X射线衍射仪（XRD）、扫描电子显微镜（SEM）、傅里叶变换红外光谱仪（FT-IR）、X射线光电子能谱仪（XPS）以及紫外可见分光光度计（UV-vis）来表征．所合成的样品具有较强的光催化活性,可通过在可见光照射下降解有机染料罗丹明B（RhB）来验证．C自掺杂TiO2所呈现的较强光催化活性是由于其具有小的能带间隙（2.74 eV）、大的比表面积和高的电子-空穴对分离率．     

C自掺杂TiO2纳米棒的制备与光催化性能研究

本文以TiC为前驱体和掺杂源,采用一步水热法合成了具有可见光吸收的C自掺杂金红石相TiO_2纳米棒.样品的结构、形貌、化学态和光学性质等可通过X射线衍射仪(XRD)、扫描电子显微镜(SEM)、傅里叶变换红外光谱仪(FT-IR)、X射线光电子能谱仪(XPS)以及紫外可见分光光度计(UV-vis)来表征.所合成的样品具有较强的光催化活性,可通过在可见光照射下降解有机染料罗丹明B(RhB)来验证.C自掺杂TiO_2所呈现的较强光催化活性是由于其具有小的能带间隙(2.74 eV)、大的比表面积和高的电子-空穴对分离率.     

One-step solvothermal preparation of TiO2/C composites and their visible-light photocatalytic activities

Preparation of anatase type titania nanoparticles and their carbon modification were synchronously achieved by the solvothermal method with glycerol as the carbon source. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance spectra (DRS). It was found that the glycerol/ethanol ratio affected significantly the morphology and properties of TiO₂/C composites. The TiO₂/C composite which was obtained in the solution with the glycerol/ethanol ratio of 5/75, contained 1.2 mass% carbon and exhibited both superior adsorption capability and visible-light photocatalytic activity. Contrary to this, samples prepared in the solution with higher glycerol/ethanol ratio, exhibited lower photocatalytic activity similar to that of the titania without carbon modification. It was suggested that excess addition of glycerol might contribute to large amounts of carbonaceous species and severe aggregation of the as-prepared samples, and thus reduced the surface area. As a result, the adsorption capability and visible-light photocatalytic activity increased at first and then decreased with the increase of glycerol addition. Present study provided a facile one-step method to obtain TiO₂/C composites with a controllable carbon content and photocatalytic performance under mild temperature.     

Synthesis and formaldehyde sensing performance of LaFeO3 hollow nanospheres

Metal oxide semiconductors with hollow structure and morphology have attracted considerable attentions because of their promising application on gas sensors. In this paper, LaFeO₃ hollow nanospheres have been prepared by using carbon spheres as templates in combination with calcination. Based on the observation of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), and transmission electron microscope (TEM), the structure and morphology of the products were characterized. It has been revealed that as-prepared LaFeO₃ samples have a uniform diameter of around 300 nm and hollow structures with thin shells of about 30 nm consisting of numerous nanocrystals and nanopores. Owing to the hollow and porous structure, large surface area and more surface active sites, the sensor based on LaFeO₃ hollow nanospheres exhibited high response, good selectivity and stability to formaldehyde gas (HCHO). It suggests that the as-prepared LaFeO₃ hollow nanospheres are promising candidates for good performance formaldehyde sensor.     

BiVO4空心微球的合成及其光催化降解亚甲基蓝的性能研究

以BiNO₃·5H₂O和NH₄VO₃为原料,柠檬酸为络合剂,成功合成了BiVO₄空心纳米球．采用TEM、XRD、UV-Vis等测试技术对样品的形貌、相结构以及光吸收性能等进行了表征．结果表明,所制备的BiVO₄空心微球在紫外区和可见区均有较强的光吸收,空心球平均粒径为160 nm,空腔直径为10～80 nm．以亚甲基蓝染料溶液的脱色降解实验为模型反应研究了样品的光催化性能．光催化实验结果表明,在可见光照射下,反应150 min后,样品对亚甲基蓝溶液的脱色率可达到95%以上．此外,考察了柠檬酸添加量对空心球形貌的影响,并提出了BiVO₄空心纳米球的可能形成机理．     

Preparation of Ag-doped mesoporous titania and its enhanced photocatalytic activity under UV light irradiation

Ag-doped mesoporous titania was synthesized via a combined sol-gel process with surfactant-assisted templating method using cetyltrimethyl ammonium bromide (CTAB) as the structure-directing agent. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity of the samples was determined by degradation of model contaminant water of phenol in aqueous solution. Results showed that different amounts of Ag-doping had different effects on the crystal phase structure and photocatalytic activity of the samples. The sample with 0.5% Ag doping shows the highest photocatalytic activity, which is 2.3 times that of the undoped mesoporous titania.     

Synthesis,characterization, and photocatalytic properties of Ni<Subscript>12</Subscript>P<Subscript>5</Subscript> hollow microspheres

Ni₁₂P₅ hollow microspheres were prepared by a simple mixed cetyltrimethyl ammonium bromide/sodium dodecyl sulfate surfactant-assisted hydrothermal route. The as-prepared Ni₁₂P₅ microstructures were characterized by X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). It was interesting to find that cetyltrimethyl ammonium bromide/sodium dodecyl sulfate could form a micro-reactor by the mixed micelles in the aqueous solution, which served as a soft template for Ni₁₂P₅ hollow microspheres with a diameter of 2~6 μm. Moreover, the as-prepared Ni₁₂P₅ hollow microspheres exhibited a good photocatalytic degradation activity for some organic dyes (such as Rhodamine B, Methylene Blue, Pyronine B, and Safranine T), and the degradation ratio could achieve more than 80%.     

Visible-light-driven titania photocatalyst co-doped with nitrogen and ferrum

Nitrogen and ferrum co-doped titania photocatalyst was prepared by the sol-gel route. The prepared photocatalyst was characterized by various techniques including X-ray diffraction (XRD), UV-vis diffusive reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), and N₂ adsorption-desorption isotherm. The photocatalytic activity of the co-doped titania photocatalyst was evaluated by the degradation of methyl orange (MO) from aqueous solution under visible light irradiation and was compared with that of the commercial TiO₂ photocatalyst (Degussa P25). The results revealed that the nitrogen doping could lead to the response to visible light and that the ferrum doping could improve the photocatalytic performance. The effects of the component and the annealing temperature of the co-doped titania photocatalyst on the photocatalytic activity were investigated.     

Structure and photocatalytic properties of copper-doped rutile TiO2 prepared by a low-temperature process

Copper-doped titania with variable Cu/Ti ratios have been prepared via a simple aqueous-phase method at 85 °C. The obtained products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and UV-vis absorption spectra analysis. The photocatalytic properties of the products were tested by photocatalytic degradation of aqueous brilliant red X-3B solution. The results showed that the sample with 2% copper doping has the best photocatalytic activity, which is 3 times that of undoped rutile titania. The effect of the doped copper on the structure and property of TiO₂ has also been discussed.     

Influence of two different template removal methods on the micromorphology,crystal structure,and photocatalytic activity of hollow CdS nanospheres

Hollow cadmium sulfide (CdS) nanospheres of about 260 nm average diameters and about 30 nm shell thickness can be easily synthesized via a sonochemical process, in which polystyrene (PS) nanoparticles were employed as templates. In order to remove the PS templates, both etching and calcination were applied in this paper. The influence of the two different template removal methods on the surface micromorphology, crystal structure, and photocatalytic activity of hollow CdS nanospheres was carefully performed a comparative study. Results of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray, FT-IR, thermogravimetric analysis, Brunauer–Emmett–Teller, diffused reflectance spectra, and decolorization experiments showed that the different template removal methods exhibited a significant influence on the surface micromorphology, crystal structure, and photocatalytic activity of hollow CdS nanospheres. The CdS hollow nanospheres as-prepared by etching had pure cubic sphalerite structure, higher –OH content, less defects and exhibited good photocatalytic activity for rhodamine-B, Methylene Blue and methyl orange under UV–vis light irradiation. However, CdS hollow nanospheres obtained by calcination with a hexagonal crystal structure, less –OH content, more defects have shown worse photocatalytic activity. This indicated that surface micromorphology and crystalline phase were mainly factors influencing photocatalytic activity of hollow CdS nanospheres.     

Template-free synthesis of ZnV2O4 hollow spheres and their application for organic dye removal

Hollow ZnV₂O₄ spheres with the shell aggregated by small nanoparticles were successfully synthesized through a facile one-pot template-free solvothermal method. The as-prepared product was characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller N₂ adsorption-desorption analyses. The formation of ZnV₂O₄ hollow spheres was based on flowerlike intermediate products supported reduction-dissolution-aggregation process at the expense of consumption of all the flowerlike products. The obtained ZnV₂O₄ hollow spheres showed a good adsorption capacity of methylene blue (MB) organic dye, which might be attributed to their special structural feature with large surface area. The adsorption kinetics and isotherm of MB on ZnV₂O₄ hollow spheres were also studied.     

Triblock copolymer-templated synthesis of porous TiO2 and its photocatalytic activity

Mixed amorphous and anatase-type titania particles were synthesized using non-ionic triblock copolymer as surfactant template and TiOSO₄ as inorganic precursor through sol–gel process. The as-prepared materials were characterized by X-ray diffraction spectroscopy, scanning and transmission electron microscopy, specific surface area, Fourier-transformed infrared spectroscopy, and diffuse reflectance ultraviolet–visible spectroscopy. The template material could be easily removed by extracting with dichloromethane and was confirmed by infrared spectroscopy. X-ray diffraction pattern reveals the crystalline part of as-prepared product as a framework of anatase phase. From the N₂ adsorption–desorption analysis, the as-prepared sample has a surface area of 301 m²/g with pore size distribution narrowly centered around 6 nm. The photodegradation of indigo carmine including kinetics, effect of pH, and recyclability of the product were investigated. The photocatalytic results showed that the as-synthesized titania could efficiently degrade indigo carmine under ultraviolet irradiation and showed higher photocatalytic activity than the commercial Degussa P25–TiO₂.