Influence of annealing temperature on structural and optical properties of ZnO: In thin films prepared by ultrasonic spray technique

Transparent conducting indium doped zinc oxide was deposited on glass substrate by ultrasonic spray method. The In doped ZnO samples with indium concentration of 3 wt.% were deposited at 300, 350 and 400 °C with 2 min of deposition time. The effects of substrate temperature and annealing temperature on the structural, electrical and optical properties were examined. The DRX analyses indicated that In doped ZnO films have polycrystalline nature and hexagonal wurtzite structure with (0 0 2) preferential orientation and the maximum average crystallite size of ZnO: In before and annealed at 500 °C were 45.78 and 55.47 nm at a substrate temperature of 350 °C. The crystallinity of the thin films increased by increasing the substrate temperature up 350 °C, the crystallinity improved after annealing temperature at 500 °C. The film annealed at 500 °C and deposited at 350 °C show lower absorption within the visible wavelength region. The band gap energy increased from E_g = 3.25 to 3.36 eV for without annealing and annealed films at 500 °C, respectively, indicating that the increase in the transition tail width. This is due to the increase in the electrical conductivity of the films after annealing temperature.     

Optical and electrical properties of In-doped CdO thin films fabricated by pulse laser deposition

Transparent indium-doped cadmium oxide (In-CdO) thin films were deposited on quartz glass substrates by pulse laser deposition (PLD) from ablating Cd-In metallic target at a fixed pressure 10 Pa and a fixed substrate temperature 300 °C. The influences of indium concentrations in target on the microstructure, optical and electrical performances were studied. When the indium concentration reaches to 3.9 wt%, the as-deposited In-CdO film shows high optical transmission in visible light region, obviously enhanced direct band gap energy (2.97 eV), higher carrier concentration and lower electric resistivity compared with the undoped CdO film, while a further increase of indium concentration to 5.6 wt% induces the formation of In₂O₃, which reverse the variation of these parameters and performance.     

Microstructural, optical and spectroscopic studies of laser ablated nanostructured tantalum oxide thin films

Thin films of tantalum oxide (Ta₂O₅) have been prepared by pulsed laser deposition technique at different substrate temperatures (300-973 K) under vacuum and under oxygen background (pO₂ = 2 × 10⁻³ mbar) conditions. The films are annealed at a temperature of 1173 K. The as-deposited films are amorphous irrespective of the substrate temperature. XRD patterns show that on annealing, the films get crystallized in orthorhombic phase of tantalum pentoxide (β-Ta₂O₅). The annealed films deposited at substrate temperatures 300 K and 673 K have a preferred orientation along (0 0 1) plane, whereas the films deposited at substrate temperatures above 673 K show a preferred orientation along (2 0 0) crystal plane. The deposited films are characterized using techniques such as grazing incidence X-ray diffraction (GIXRD), atomic force microscopy (AFM), micro-Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy and UV-visible spectroscopy. FTIR and micro-Raman measurements confirm the presence of Ta-O, Ta-O-Ta and O-Ta-O bands in the films. Grain size calculations from X-ray diffraction and AFM show a decrease with increase in substrate temperature. The variation of transmittance and band gap with film growth parameters are also discussed.     

Optical and electrical properties of thermally oxidized bismuth thin films

Bismuth trioxide (Bi₂O₃) thin films were prepared by dry thermal oxidation of metallic bismuth films deposited by vacuum evaporation. The oxidation process of Bi films consists of a heating from the room temperature to an oxidation temperature (T_o = 673 K), with a temperature rate of 8 K/min; an annealing for 1 h at oxidation temperature and, finally, a cooling to room temperature. The optical transmission and reflection spectra of the films were studied in spectral domains ranged between 300 nm and 1700 nm, for the transmission coefficient, and between 380 nm and 1050 nm for the reflection coefficient, respectively. The thin-film surface structures of the metal/oxide/metal type were used for the study of the static current-voltage (I-U) characteristics. The temperature of the substrate during bismuth deposition strongly influences both the optical and the electrical properties of the oxidized films. For lower values of intensity of electric field (ξ < 5 × 10⁴V/cm), I-U characteristics are ohmic.     

Novel type of indium oxide thin films sputtering for opto-electronic applications

Transparent conductive oxide (TCO) thin films play a significant role in recent optical technologies. Displays of various types, photovoltaic systems, and opto-electronic devices use these films as transparent signal electrodes. They are used as heating surfaces and active control layers. Oxides of TCO materials such as: tin, indium, zinc, cadmium, titanium and the like, exhibit their properties. However, indium oxide and indium oxide doped with tin (ITO) coatings are the most used in this technology.In this work, we present conductive transparent indium oxide thin films which were prepared using a novel triode sputtering method. A pure In₂O₃ target of 2 in. in diameter was used in a laboratory triode sputtering system. This system provided plane plasma discharge at a relatively low pressure 0.5-5 mTorr of pure argon. The substrate temperature was varied during the experiments from room temperature up to 200 °C. The films were deposited on glass, silicon, and flexible polyimide substrates. The films were characterized for optical and electrical properties and compared with the indium oxide films deposited by magnetron sputtering.     

Effects of substrate temperature and Zn addition on the properties of Al-doped ZnO films prepared by magnetron sputtering

Al-doped ZnO (AZO) films prepared at different substrate temperature and AZO films with intentional Zn addition (ZAZO) during deposition at elevated substrate temperature were fabricated by radio frequency magnetron sputtering on glass substrate, and the resulting structural, electrical, optical properties together with the etching characteristics and annealing behavior were comparatively examined. AZO films deposited at 150 °C showed the optimum electrical properties and the largest grain size. XPS analysis revealed that AZO films deposited at elevated temperature of 450 °C contained large amount of Al content due to Zn deficiency, and that intentional Zn addition during deposition could compensate the deficiency of Zn to some extent. It was shown that the electrical, optical and structural properties of ZAZO films were almost comparable to those of AZO film deposited at 150 °C, and that ZAZO films had much smaller etching rate together with better stability in severe annealing conditions than AZO films due possibly to formation of dense structure.     

Effects of the substrate temperature on the properties of CuIn5S8 thin films

Structural, optical and electrical properties of CuIn₅S₈ thin films grown by thermal evaporation have been studied relating the effects of substrate heating conditions of these properties. The CuIn₅S₈ thin films were carried out at substrate temperatures in the temperature range 100-300 °C. The effects of heated substrate on their physico-chemical properties were investigated using X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), optical transmission and hot probe method. X-ray diffraction revealed that the films are strong preferred orientation along the (3 1 1) plane upon substrate temperature 200 °C and amorphous for the substrate temperatures below 200 °C. No secondary phases are observed for all the films. The composition is greatly affected by heated substrate. From the optical transmission and reflection, an important absorption coefficient exceeds 10⁵ cm⁻¹ at 800 nm was found. As increasing the substrate temperature, the optical energy band gap decreases from 1.70 eV for the unheated films to 1.25 eV for the deposited films at 300 °C. It was found that CuIn₅S₈ thin film is an n-type semiconductor at 250° C.     

Growth mechanism and optoelectronic properties of nanocrystalline In2O3 films prepared by chemical spray pyrolysis of metal-organic precursor

Thin films of indium oxide, In₂O₃, were deposited by chemical spray pyrolysis technique, using aqueous alcoholic solutions of indium acetylacetonate (In-acac) precursor, on glass substrates kept at temperatures between 300 and 500 °C. The structural, optical, and electrical properties have been investigated as a function of deposition temperature, precursor concentration, carrier gas pressure, and substrate-to-nozzle distance. X-ray diffraction studies showed that the formation of nanocrystalline In₂O₃ films is preferentially oriented along (2 2 2) plane. The surface morphological modifications with substrate temperature were observed using scanning electron and atomic force microscopic studies. Optical transmittance behavior of the films in the visible and IR region was strongly affected by the deposition parameters. The optical band gap values observed are between 3.53 and 3.68 eV. The long wavelength limit of refractive index is 1.83. The Hall mobility is found to vary from 23 to 37 cm²/V s and carrier density is found nearly constant at about 10²⁰ cm⁻³.     

Influence of indium content on the optical, electrical and crystallization kinetics of Se100−xInxthin films deposited by flash evaporation technique

Thin films of Se _100−xIn_x (x=10, 20 and 30 at%) have been prepared by the flash evaporation technique. The effect of the indium content on optical band gap of the Se_100−x In_x films has been investigated by the optical characterization. The optical band gap values of the Se_100−x In_x thin films were determined and are found to decrease with increasing indium content. This indium content changes the width of localized states in the optical band gaps of the thin films. It was found that the optical band gap, E_g, of the Se_100−x In_x films changes from 1.78 to 1.37 eV with increasing indium content from 10 to 30 at%, while the width of localized states in optical band gap changes from 375 to 342 meV. The temperature dependence of the dark electrical conductivity were studied in the temperature range 303-433 K and revealed two activation energies providing two electrical conduction mechanisms. The activation energy of the Se_100−x In_x films in the high temperature region changes from 0.49 to 0.32 eV with increasing indium content from 10 to 30 at%, while the hopping activation energy in the lower temperature region changes from 0.17 to 0.22 meV. The change in the electrical conductivity with time during the amorphous-to-crystalline transformation is recorded for amorphous Se_100−xIn_x films at two points of isothermal temperatures 370 and 400 K. The formal crystallization theory of Avrami has been used to calculate the kinetic parameters of crystallization.     

Characterization of chemically deposited ZnSe/SnO2/glass films: Influence of annealing in Ar atmosphere on physical properties

The Zinc Selenide (ZnSe) thin films have been deposited on SnO₂/glass substrates by a simple and inexpensive chemical bath deposition (CBD). The structural, optical and electrical properties of ZnSe films have been characterized by X-ray diffraction (XRD), Energy Dispersive X-ray Analysis (EDAX), optical absorption spectroscopy, and four point probe techniques, respectively. The films have been subjected to different annealing temperature in Argon (Ar) atmosphere. An increase in annealing temperature does not cause a complete phase transformation whereas it affects the crystallite size, dislocation density and strain. The optical band gap (E_g) of the as-deposited film is estimated to be 3.08 eV and decreases with increasing annealing temperature down to 2.43 eV at 773 K. The as-deposited and annealed films show typical semiconducting behaviour, dρ/dT > 0. Interestingly, the films annealed at 373 K, 473 K, and 573 K show two distinct temperature dependent regions of electrical resistivity; exponential region at high temperature, linear region at low temperature. The temperature at which the transition takes place from exponential to linear region strongly depends on the annealing temperature.     

Effect of substrate temperature on the surface and interface oxidation of NiTi thin films

NiTi shape memory alloy thin films are deposited on pure Cu substrate at substrate ambient temperatures of 300 °C and 450 °C. The surface and interface oxidation of NiTi thin films are characterized by X-ray photoelectron spectroscopy (XPS). After a subsequent annealing treatment the crystallization behavior of the films deposited on substrate at different temperatures is studied by X-ray diffraction (XRD). The effects of substrate temperature on the surface and interface oxidation of NiTi thin films are investigated. In the film surface this is an oxide layer composed of TiO₂. The Ni atom has not been detected on surface. In the film/substrate interface there is an oxide layer with a mixture Ti₂O₃ and NiO in the films deposited at substrate temperatures 300 °C and 450 °C. In the films deposited at ambient temperature, the interface layer contains Ti suboxides (TiO) and metallic Ni.     

The optoelectronic properties of silicon films deposited by inductively coupled plasma CVD

Hydrogenated amorphous and microcrystalline silicon films were deposited by inductively coupled plasma chemical vapor deposition (ICP-CVD) at low substrate temperatures using H₂-diluted SiH₄ as a source gas. High-density plasma generated by inductively coupled excitation facilitates the crystallization of silicon films at low temperatures, and microcrystalline silicon films were obtained at the substrate temperature as low as 180 °C. The columnar structure of the films becomes more and more compact with an increase of their crystallinity. The reduction of hydrogen content in the films causes a narrowing of the optical bandgap and an enhancement of the absorption with increasing the substrate temperature. The microcrystalline silicon films show two electronic transport mechanisms: one is related to the density of state distribution in the temperature region near room temperature and the other is the variable range hopping between localized electronic states close to the Fermi level below 170 K. A reasonable explanation is presented for the dependence of the optoelectronic properties on the microstructure of the silicon films. The films prepared at a substrate temperature of 300 °C have highly crystalline and compact columnar structure, high optical absorption coefficient and electrical conductivity, and a low hydrogen content of 3.8%.     

Structural and electrical transport properties of Nb-doped TiO2 films deposited on LaAlO3 by rf sputtering

We have investigated the structural and electrical transport properties of Nb-doped TiO₂ films deposited on (1 0 0) LaAlO₃ substrates by rf magnetron sputtering at temperatures ranging from 873 K to 1073 K. Films deposited below 998 K are anatase, and mixed phases between anatase and rutile exist in the film grown at higher temperatures. We find that films deposited at low temperatures exhibit semiconductor behavior, while metallic conductivity is observed in the most conducting film deposited at 998 K. For this sample, compared to electron-phonon scattering mechanism, electron-phonon-impurity interference effect plays an important role in its electron transport process. Moreover, the temperature coefficient of the resistivity for the film deposited at 1073 K is negative from 2 K to 300 K. The temperature dependence of resistivity for the film is described by ∼exp(b/T)^1/2 at temperatures from 80 K down to 30 K, and by the fluctuation induced tunneling model from 80 K to 300 K.     

Optical and electrical properties of thermally evaporated In49Se48Sn3 films

Nearly stoichiometric thin films of In₄₉Se₄₈Sn₃ were deposited at room temperature, by conventional thermal evaporation of the presynthesized materials, onto precleaned glass substrates. The microstructural studies on the as-deposited and annealed films, using transmission electron microscopy and diffraction (TEMD), revealed that the as-deposited films are amorphous in nature, while those annealed at 498 K are crystalline. The optical properties of the investigated films were determined from the transmittance and reflectance data, in the spectral range 650-2500 nm. An analysis of the optical absorption spectra revealed a non-direct energy gap characterizing the amorphous films, while both allowed and forbidden direct energy gaps characterized the crystalline films. The electrical resistance of the deposited films was carried out during heating and cooling cycles in the temperature range 300-600 K. The results show an irreproducible behavior, while after crystallization the results become reproducible. The analysis of the temperature dependence of the resistance (ln(R) vs. 1000/T) for crystalline films shows two straight lines corresponding to both extrinsic and intrinsic conduction. The room temperature I-V characteristics of the as-deposited films sandwiched between similar Ag metal electrodes shows an ohmic behavior, while non-ohmic behavior attributed to space charge limited conduction has been observed when the films are sandwiched between dissimilar Ag/Al metal electrodes.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Effect of oxygen content and deposition temperature on the characteristics of thin silver films deposited by magnetron sputtering

Thin silver films were prepared by direct current magnetron sputtering in a single-ended in-line sputter system at various substrate temperatures and in O₂ contents in sputter gas, and their electrical, optical, structural and morphological properties together with the compositional properties were investigated. When deposited at room temperature, the electrical and optical properties of Ag films deteriorated with addition of O₂ to sputter gas. Deposition of Ag films in O₂ added sputter gas promoted the formation of Ag crystallites with (2 0 0) plane parallel to the substrate surface. The electrical resistivity and optical reflection of Ag films deposited above 100 °C were not affected by the sputtering plasma containing oxygen. X-ray photoelectron spectroscopic analysis showed that Ag films deposited above 100 °C in O₂ added sputter gas did not possess surplus oxygen in the film, and that the oxidation states of these films were almost identical to that of Ag films deposited in pure Ar gas.     

Photosensitivity of nanocrystalline ZnO films grown by PLD

We have studied the properties of ZnO thin films grown by laser ablation of ZnO targets on (0 0 0 1) sapphire (Al₂O₃), under substrate temperatures around 400 °C. The films were characterized by different methods including X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and atomic force microscopy (AFM). XPS analysis revealed that the films are oxygen deficient, and XRD analysis with θ-2θ scans and rocking curves indicate that the ZnO thin films are highly c-axis oriented. All the films are ultraviolet (UV) sensitive. Sensitivity is maximum for the films deposited at lower temperature. The films deposited at higher temperatures show crystallite sizes of typically 500 nm, a high dark current and minimum photoresponse. In all films we observe persistent photoconductivity decay. More densely packed crystallites and a faster decay in photocurrent is observed for films deposited at lower temperature.     

Effect of substrate temperature and annealing temperature on the structural, electrical and microstructural properties of thin Pt films by rf magnetron sputtering

Influence of both substrate temperature, T_s, and annealing temperature, T_a, on the structural, electrical and microstructural properties of sputtered deposited Pt thin films have been investigated. X-ray diffraction results show that as deposited Pt films (T_s = 300, 400 °C) are preferentially oriented along (1 1 1) direction. A little growth both along (2 0 0) and (3 1 1) directions are also noticed in the as deposited Pt films. After annealing in air (T_a = 500-700 °C), films become strongly oriented along (1 1 1) plane. With annealing temperature, average crystallite size, D, of the Pt films increases and micro-strain, e, and lattice constant, a₀, decreases. Residual strain observed in the as deposited Pt films is found to be compressive in nature while that in the annealed films is tensile. This change in the strain from compressive to tensile upon annealing is explained in the light of mismatch between the thermal expansion coefficients of the film material and substrate. Room temperature resistivity of Pt films is dependant on both the T_s and T_a of the films. Observed decrease in the film resistivity with T_a is discussed in terms of annihilation of film defects and grain-boundary. Scanning electron microscopic study reveals that as the annealing temperature increases film densification improves. But at an annealing temperature of ∼600 °C, pinholes appear on the film surface and the size of pinhole increases with further increase in the annealing temperature. From X-ray photoelectron spectroscopic analysis, existence of a thin layer of chemisorbed atomic oxygen is detected on the surfaces of the as deposited Pt films. Upon annealing, coverage of this surface oxygen increases.     

Influence of substrate temperature and post-treatment on the properties of ZnO:Al thin films prepared by pulsed laser deposition

Highly transparent conductive Al₂O₃ doped zinc oxide (AZO) thin films have been deposited on the glass substrate by pulsed laser deposition technique. The effects of substrate temperature and post-deposition annealing treatment on structural, electrical and optical properties of AZO thin films were investigated. The experimental results show that the electrical resistivity of films deposited at 240 °C is 6.1 × 10⁻⁴ Ω cm, which can be further reduced to as low as 4.7 × 10⁻⁴ Ω cm by post-deposition annealing at 400 °C for 2 h in argon. The average transmission of AZO films in the visible range is 90%. The optical direct band gap of films was dependent on the substrate temperature and the annealing treatment in argon. The optical direct band gap value of AZO films increased with increasing annealing temperature.     

Characteristics of Ni films deposited on SiO2/Si(1 0 0) and MgO(0 0 1) by direct current magnetron sputtering system with the oblique target

280 nm-thick Ni films were deposited on SiO₂/Si(1 0 0) and MgO(0 0 1) substrates at 300 K, 513 K and 663 K by a direct current magnetron sputtering system with the oblique target. The films deposited at 300 K mainly have a [1 1 0] crystalline orientation in the film growth direction. The [1 1 0]-orientation weakens and the [1 1 1]- and [1 0 0]-orientations enhance with increasing deposition temperature. The lattice constant of the Ni films is smaller than that of the Ni bulk, except for the film grown on MgO(0 0 1) at 663 K. Furthermore, as the deposition temperature increases, the lattice constant of the films grown on the SiO₂/Si(1 0 0) decreases whereas that of the films grown on the MgO(0 0 1) increases. The films deposited at 300 K and 513 K grow with columnar grains perpendicular to the substrate. For the films deposited at 663 K, however, the columnar grain structure is destroyed, i.e., an about 50 nm-thick layer consisting of granular grains is formed at the interface between the film and the substrate and then large grains grow on the layer. The Ni films deposited at 300 K consist of thin columnar grains and have many voids at the grain boundaries. The grains become thick and the voids decrease with increasing deposition temperature. The resistivity of the film decreases and the saturation magnetization increases with increasing deposition temperature.