Chrysanthemum-like Co3O4 architectures: Hydrothermal synthesis and lithium storage performances

Three-dimensional chrysanthemum-like Co₃O₄ was prepared via a facile hydrothermal route without any template, and a subsequent calcination process. With a controlled concentration of the homogeneous precipitation agent, urea, a chrysanthemum-like precursor was hydrothermally obtained at 120 °C for 20 h, and the morphology was kept for Co₃O₄ after a subsequent calcination at 300 °C for 2 h. Co₃O₄ chrysanthemum-like architectures are assemblies of nanorods radiating from a common centre, and the nanorods consisted of interconnected nanoparticles with the size of about 30 nm. When tested as an anode material of Li-ion batteries, chrysanthemum-like Co₃O₄ presented a discharge capacity of ∼450 mA h/g after 50 discharge/charge cycles.     

Reversible lithium storage in Na2Li2Ti6O14 as anode for lithium ion batteries

The sodium lithium titanate with composition Na₂Li₂Ti₆O₁₄ has been synthesized by a sol–gel method. Thermogravimetric analysis and differential thermal analysis (TG–DTA) of the thermal decomposition process of the precursor and X-ray diffraction (XRD) data indicate the crystallization of sodium lithium titanate has occurred at about 600 °C. Electrochemical lithium insertion into Na₂Li₂Ti₆O₁₄ for lithium ion battery has been investigated for the first time. These results indicate the discharge and charge potential plateaus are about 1.3 V. The initial discharge capacity is much higher than the charge capacity and irreversible capacity exists in the voltage window 1–3 V. Subsequently, the discharge capacity decreases slowly, but the charge capacity increases slightly in the following cycles. After a few cycles, the specific capacity remains almost constant values and the sample exhibits the excellent retention of capacity on cycling.     

Structural and electrochemical investigation of Li2MgSnO4 anode for lithium batteries

Hexagonal Li₂MgSnO₄ compound was synthesized at 800 °C using Urea Assisted Combustion (UAC) method and the same has been exploited as an anode material for lithium battery applications. Structural investigations through X-ray diffraction, Fourier Transform Infra Red spectroscopy and ⁷Li NMR (Nuclear Magnetic Resonance spectroscopy) studies demonstrated the existence of hexagonal crystallite structure with a = 6.10 and c = 9.75. An average crystallite size of ∼400 nm has been calculated from PXRD pattern, which was further evidenced by SEM images. An initial discharge capacity of ∼794 mA h/g has been delivered by Li₂MgSnO₄ anode with an excellent capacity retention (85%) and an enhanced coulombic efficiency (97–99%). Further, the Li₂MgSnO₄ anode material has exhibited a steady state reversible capacity of ∼590 mA h/g even after 30 cycles, thus qualifying the same for use in futuristic lithium battery applications.     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

LiMn2O4 hollow nanosphere electrode material with excellent cycling reversibility and rate capability

Lithium-rich Li_1.05Mn₂O₄ hollow nanospheres have been successfully prepared by air-calcining lithiated MnO₂ precursor at a low temperature of 550 °C, which was synthesized by chemical lithiation of hollow MnO₂ nanospheres with LiI at 70 °C for 12 h. The lithium-rich Li_1.05Mn₂O₄ hollow nanospheres exhibit an excellent cycling stability and rate capability as a cathode material for rechargeable lithium batteries: it maintains 90% of its initial capacity after 500 cycles, and keeps 70% of the reversible capacity at 0.1 C rat, even at 15 C rate.     

Electrochemical properties of Li(Li(1−x)/3CoxMn(2−2x)/3)O2 (0 ⩽ x ⩽ 1) solid solutions prepared by poly-vinyl alcohol (PVA) method

The whole range of solid solutions Li(Li_(1−x)/3Co_xMn_(2−2x)/3)O₂ (0 ⩽ x ⩽ 1) was firstly synthesized by an aqueous solution method using poly-vinyl alcohol as a synthetic agent to investigate their structure and electrochemical properties. X-ray diffraction results indicated that the synthesized solid solutions showed a single phase without any detectable impurity phase and have a hexagonal structure with some additional peaks caused by monoclinic distortion, especially in the solid solutions with a low Co amount. In the electrochemical examination, the solid solutions in the range between 0.2 ⩽ x ⩽ 0.9 showed higher discharge capacity and better cyclability than LiCoO₂ (x = 1) on cycling between 2.0 and 4.6 V with 100 mA g⁻¹ at 25 °C. For example, Li(Li_0.2Co_0.4Mn_0.4)O₂ (x = 0.4) exhibited a high discharge capacity of 180 mA h g⁻¹ at the 50th cycle. By synthesizing the solid solution between Li₂MnO₃ and LiCoO₂, the electrochemical properties of the end members were improved.     

LixV2O5 nanobelts for high capacity lithium-ion battery cathodes

5–10 μm long, typically 200–300 nm wide, and several nanometers thick Li_xV₂O₅ (× ～ 0.8) nanobelts with the δ-type crystal structure were synthesized by a hydrothermal treatment of Li⁺-exchanged V₂O₅ gel. When dried at 200 °C under vacuum prior to electrochemical testing, the as-prepared nanobelts underwent the well-known δ → ε → γ-phase transition giving a mixture of ε and γ phases as a nanocomposite electrode material. Such a simple preparation procedure guarantees a yield of material with drastically enhanced initial discharge specific capacity of 490 mAh/g and great cyclability. The enhanced electrochemical performance is attributed to the complex of experimental procedures including post-synthesis treatment of the single-crystalline Li_xV₂O₅ nanobelts.     

Low temperature synthesis of highly ion conductive Li7La3Zr2O12–Li3BO3 composites

Highly lithium ion conductive composites with Al-doped Li₇La₃Zr₂O₁₂ (LLZ) and amorphous Li₃BO₃ were prepared from sol–gel derived precursor powders of LLZ and Li₃BO₃. Precursor LLZ powders with cubic phase were obtained by a heat treatment of the precursor dried gel at 600 °C. Pellets of the mixture of the obtained LLZ and Li₃BO₃ were first held at 700 °C, and then successively sintered at 900 °C. Density of the sintered pellet with Li₃BO₃ was larger than that of the pellet without Li₃BO₃. From the TEM observation, the pellets were found to consist of cubic LLZ and amorphous Li₃BO₃. Total electrical conductivity of the obtained LLZ–Li₃BO₃ composite was 1 × 10^− 4 Scm^− 1 at 30 °C.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

Electrochemical properties of Li symmetric solid-state cell with NASICON-type solid electrolyte and electrodes

All-solid-state phosphate symmetric cells using Li₃V₂(PO₄)₃ for both the positive and negative electrodes with the phosphate Li_1.5Al_0.5Ge_1.5(PO₄)₃ as the solid electrolyte were proposed. Amorphous Li_1.5Al_0.5Ge_1.5(PO₄)₃ was added into the electrode to increase the interface area between the active materials and the electrolyte. Any other phases were not formed at the electrode/electrolyte interface even after hot pressing at 600 °C. The discharge capacity was 92 mAh g^? 1 at 22 µA cm^? 2 at 80 °C, and 38 mAh g^? 1 at 25 °C, respectively. Symmetric cell configuration leads to simplify the fabrication process for all-solid-state batteries and will reduce manufacturing costs.     

Olivine LiCoPO4 phase grown LiCoO2 cathode material for high density Li batteries

Olivine LiCoPO₄ phase grown LiCoO₂ cathode material was prepared by mixing precipitated Co₃(PO₄)₂ nanoparticles and LiCoO₂ powders in distilled water, followed by drying and annealing at 120 °C and 700 °C, respectively, for 5 h. As opposed to ZrO₂ or AlPO₄ coatings that showed a clearly distinguishable coating layer from the bulk materials, Co₃(PO₄)₂ nanoparticles were completely diffused into the surface of the LiCoO₂ and reacted with lithium of LiCoO₂. An olivine LiCoPO₄ phase was grown on the surface of the bulk LiCoO₂, with a thickness of ∼7 nm. The electrochemical properties of the LiCoPO₄ phase, grown in LiCoO₂, had excellent cycle life performance and higher working voltages at a 1C rate than the bare sample. More importantly, Li-ion cells, containing olivine LiCoPO₄, grown in LiCoO₂, showed only 10% swelling at 4.4 V, whereas those containing bare sample showed a 200% increase during storage at 90 °C for 5 h. In addition, nail penetration test results of the cell containing olivine LiCoPO₄, grown in LiCoO₂ at 4.4 V, did not exhibit thermal runaway with a cell surface temperature of ∼80 °C. However, the cell containing bare LiCoO₂ showed a burnt-off cell pouch with a temperature above 500 °C.     

Novel SrSc0.2Co0.8O3−δ as a cathode material for low temperature solid-oxide fuel cell

The SrSc_0.2Co_0.8O_3−δ (SSC) perovskite was investigated as a cathode material for low temperature solid-oxide fuel cell. The material showed an almost linear thermal expansion from room temperature to 1000 °C in air with the average thermal expansion coefficient of only 16.9 × 10⁻⁶ K⁻¹. The Sc-doping made the absence of Co⁴⁺ in SSC, which resulted in not only dramatically reduced thermal expansion coefficient but also extremely high oxygen vacancies concentrations in the lattice at low temperature. The area specific polarization resistance was 0.206 Ω cm² for SSC at 550 °C, which is about 52% lower than the value of a Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ-based cathode. A peak power density as high as 564 mW cm⁻² was obtained at 500 °C based on a 20 μm thick Sm_0.2Ce_0.8O_1.9 electrolyte by adopting SSC cathode.     

Fabrication of solid thin film electrolyte and LiCoO2 by aerosol flame pyrolysis deposition

Aerosol flame pyrolysis deposition method was applied to deposit the oxide glass electrolyte film and LiCoO₂ cathode for thin film type Li-ion secondary battery. The thicknesses of as-deposited porous LiCoO₂ and Li₂O–B₂O₃–P₂O₅ electrolyte film were about 6 μm and 15 μm, respectively. The deposited LiCoO₂ was sintered for 2 min at 700 °C to make partially densified cathode layer, and the deposited Li₂O–P₂O₅–B₂O₃ glass film completely densified by the sintering at 700 °C for 1 h. After solid state sintering process the thicknesses were reduced to approximately 4 μm and 6 μm, respectively. The cathode and electrolyte layers were deposited by continuous deposition process and integrated into a layer by co-sintering. It was demonstrated that Aerosol flame deposition is one of the good candidates for the fabrication of thin film battery.     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

High capacity Li[Li0.2Mn0.54Ni0.13Co0.13]O2–V2O5 composite cathodes with low irreversible capacity loss for lithium ion batteries

With an aim to suppress the huge irreversible capacity loss encountered in high capacity layered oxide solid solutions between Li₂MnO₃ and LiMO₂ (M = Mn, Ni, and Co), layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with various V₂O₅ contents have been investigated. The irreversible capacity loss decreases from 68 mAh/g at 100% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ to 0 mAh/g around 89 wt.% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–11 wt.% V₂O₅ as the lithium-free V₂O₅ serves as an insertion host to accommodate the lithium ions that could not be inserted back into the layered lattice after the first charge. The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with about 10–12 wt.% V₂O₅ exhibit an attractive discharge capacity of close to 300 mAh/g with little irreversible capacity loss and good cyclability.     

A disordered rock-salt Li-excess cathode material with high capacity and substantial oxygen redox activity: Li1.25Nb0.25Mn0.5O2

A disordered rocksalt Li-excess cathode material, Li_1.25Nb_0.25Mn_0.5O₂, was synthesized and investigated. It shows a large initial discharge capacity of 287 mAh g^− 1 in the first cycle, which is much higher than the theoretical capacity of 146 mAh g^− 1 based on the Mn³⁺/Mn⁴⁺ redox reaction. In situ X-ray diffraction (XRD) demonstrates that the compound remains cation-disordered during the first cycle. Electron energy loss spectroscopy (EELS) suggests that Mn and O are likely to both be redox active, resulting in the large reversible capacity. Our results show that Li_1.25Nb_0.25Mn_0.5O₂ is a promising cathode material for high capacity Li-ion batteries and that reversible oxygen redox in the bulk may be a viable way forward to increase the energy density of lithium-ion batteries.     

Li4Ti5O12/reduced graphite oxide nano-hybrid material for high rate lithium-ion batteries

A spinel Li₄Ti₅O₁₂ nanoplatelet/reduced graphite oxide nano-hybrid was successfully synthesized by a two-step microwave-assisted solvothermal reaction and heat treatment. The Li₄Ti₅O₁₂ in the hybrid could deliver a discharge capacity of 154 mAhg^? 1 of Li₄Ti₅O₁₂ at 1 C-rate, 128 mAhg^-1 of Li₄Ti₅O₁₂ at 50 C-rate and 101 mAhg^-1 of Li₄Ti₅O₁₂ at 100 C-rate. It demonstrated promising potential as an anode material in a Li-ion battery with excellent rate capability and good cycling.     

Electrochemical characteristics of spinel Li4Ti5O12 discharged to 0.01 V

Cycling stability, reversible capacity and rate performance of Li₄Ti₅O₁₂ discharged to 0.01 V were investigated. A couple of obvious and repeatable peaks under 0.6 V observed by CV indicated that Li₄Ti₅O₁₂ possessed reversible capacity below 0.6 V. When discharge voltage of Li₄Ti₅O₁₂ extended from 0.6 to 0.01 V, its cycling stability was not affected and its reversible capacity and high rate performance were improved. Although the capacity obtained from 2.0 to 0.6 V gradually decreased with increasing the applied current density, the capacity obtained from 0.6 to 0.01 V showed little loss. AB was both electronic conducting additive and lithium-ion conducting additive for Li₄Ti₅O₁₂ under 0.6 V.     

A novel preparation method of active materials for the lithium secondary battery

LiNi_0.8Co_0.2O₂ is a promising candidate to replace LiCoO₂. The present paper describes the preparation of LiNi_0.8Co_0.2O₂ compounds from nitrate sources and sucrose (or sugar) by the sucrose combustion process (SCP), which involves application of a conventional combustion method. In the proposed approach, sucrose serves as a fuel, a dispersing agent, and a precipitation suppressant. Precursors were made via a combustion reaction, and LiNi_0.8Co_0.2O₂ was subsequently synthesized by heat treatment at 800 °C for 16 h in oxygen atmosphere. The initial discharge capacity was 175 mA h/g when a cell was operated at 2.7–4.3 V at 0.5 C-rate. Furthermore, it shows good cycling stability. When increased amount of sucrose were added as a start material, the final calcined powder displayed smaller particle size and better discharge capacity. It is expected that optimization of the heat treatment conditions would yield LiNi_0.8Co_0.2O₂ with excellent properties. Furthermore, SCP is expected to be applicable to the production of various materials.     

Sub-micrometric LiCr0.2Ni0.4Mn1.4O4 spinel as 5 V-cathode material exhibiting huge rate capability at 25 and 55 °C

Single phase LiCr_0.2Ni_0.4Mn_1.4O₄ spinel has been synthesized by a simple sucrose assisted combustion method that yields highly crystalline homogeneous sub-micrometric samples (650 nm). The LiCr_0.2Ni_0.4Mn_1.4O₄, with capacity retention of 92% at 60 C discharge rate, shows the highest rate capability among LiNi_0.5Mn_1.5O₄-type cathodes. It delivers very high-power (34.8 kW kg^?1 at 60 C). Studies developed at 55 °C demonstrate that LiCr_0.2Ni_0.4Mn_1.4O₄ retains huge rate capability and large cycleability at high temperature.