Thermally tunable microfiber knot resonator based erbium-doped fiber laser

A compact and tunable erbium-doped fiber laser is demonstrated using a highly doped fiber and a microfiber knot resonator (MKR) structure which is laid on the surface of a small peltier. The MKR functions as both a reflector and a tunable filter where tunability is achieved by varying the temperature of the resonator by heating the peltier. A stable laser output is achieved at the 1533 nm region with an optical signal to noise ratio (OSNR) of 27 dB using a 65 mW of 980 nm pump power. The operating wavelength of the laser can be tuned from 1532.60 nm to 1533.49 nm as the temperature is increased from the room temperature of 24 to 90 °C. It is observed that the operating wavelength shifts to a longer wavelength as the temperature increases with an efficiency of 12.4 pm/°C. This is due to the thermally induced optical phase shift attributable to the changes in effective refractive index and optical path length of the MKR loop.     

Multiwavelength self-seeded Brillouin-erbium fiber laser with 45-nm tunable range

We have demonstrated a tunable multiwavelength self-seeded Brillouin-erbium fiber laser (BEFL) without externally Brillouin pumping. In this scheme, the stable multiwavelength comb can be produced within a ∼45-nm wavelength tuning range through adjusting the polarization controllers (PCs) in a high-birefringent Sagnac loop mirror. The generation of ∼200-line Stokes comb has been achieved by adjusting PCs under bidirectional pumping of two laser diodes, which is the largest wavelength number to the best of our knowledge. The effect of 980 nm pump power on the multiwavelength generation was also investigated.     

Simple tunable multiwavelength Brillouin/Erbium fiber laser utilizing short-length photonic crystal fiber

We have demonstrated a simple ring cavity tunable multiwavelength Brillouin/Erbium fiber laser (MWBEFL), in which 70 m highly nonlinear photonic crystal fiber (HNL-PCF) is used as the Brillouin gain medium. The fiber laser utilizes recycling mechanism to enhance stimulated Brillouin scattering (SBS). The configuration that consists of only 3 optical components is easy to be integrated and improves the practicality. At the maximum 1480 nm pump power of 110 mW and the Brillouin pump power of 3 dBm, 10 stable output channels with more than 10 dB optical signal to noise ratio (OSNR) and 0.078 nm channel spacing could achieve 10 nm tuning ranges.     

L波段可调谐线形腔Er/Yb共掺双包层光纤激光器

报道了一种结构简单、工作在L波段、可调谐的线形腔Er/Yb共掺双包层光纤激光器.利用由两段高双折射光纤和两个偏振控制器构成的环镜滤波器对激光器进行调谐，使调谐范围达到34 nm，功率起伏小于±0.2 dB.用976 nm多模LD泵浦Er/Yb共掺双包层光纤产生的ASE作为二次泵源，对未泵浦的一段光纤进行泵浦，使腔内Er/Yb共掺光纤的增益谱移到L波段;多个泵浦源同时对Er/Yb共掺双包层光纤进行侧向泵浦，使激光器输出功率超过了200 mW.     

Wavelength tunable linear cavity cladding pump Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript>co-doped fiber laser operating in L-band

We have demonstrated a novel tunable linear cavity Er³⁺/Yb³⁺ co-doped fiber laser, which utilizes amplified spontaneous emission as a secondary pump source so that it can operate in L-band. The tuning wavelength range can be up to 34 nm, from 1588.6 to 1622.6 nm, and the output power excursion of the laser at different wavelengths can be less than 0.4 dB by using a two sections of high-birefringence fiber loop mirror as the wavelength filter. The high output power of 200 mW is realized by using the cladding-pump.     

Widely tunable sum-frequency generation in PPLN waveguide pumped by a multi-wavelength Yb-doped fiber laser

We present some experimental results on tunable sum-frequency generation in a periodically poled lithium-niobate waveguide using a multi-wavelength fiber laser pump stabilized by a nonlinear optical loop mirror. We are able to up-convert to about 629 nm a continuous-wave infrared signal varying from 1497 nm to 1525 nm. Such a wideband conversion efficiency is ensured by the multiple spectral components of the laser pump, which is controlled by an adjustable Fabry-Perot filter. Potential applications, in particular for stellar imaging, are discussed.     

8字形腔波长可调谐锁模脉冲光纤激光器

采用非线性光纤环形镜加脉冲锁模技术及可调谐光纤光栅滤波器,对8字形腔被动锁模掺铒光纤激光器进行了波长可调谐输出的实验研究.在EDFA抽运光功率一定的情况下,通过调节偏振控制器和可调谐光纤光栅滤波器,获得了光谱稳定、重复频率1.1 MHz、输出功率起伏小于0.8 dBm、中心波长在1 548~1 570 nm内连续可调的短脉冲输出.该激光器可实现自启动锁模,且长时间稳定工作无需任何调整.     

一种新型自激发布里渊掺铒光纤激光器

利用级联的受激布里渊效应,自激发布里渊掺铒光纤激光器可以实现常温下的多波长激光输出。通过在自激发掺铒光纤激光器中引入一个高双折射萨尼亚克(Sagnac)环形滤波器,调节萨尼亚克环形滤波器的偏振控制器(PC),实现了可调谐多波长输出,同时在实验中观测到双布里渊多波长带的现象。研究了这种光纤激光器中萨尼亚克环形滤波器的带宽和980 nm抽运光功率对输出波长数的影响,在萨尼亚克环形滤波器的带宽为83.3 nm以及980 nm抽运光功率为260 mW时,得到了52个间隔为0.088 nm的多波长激光输出。     

0.16 nm spaced multi-wavelength Brillouin fiber laser in a figure-of-eight configuration

A stable and compact multi-wavelength Brillouin fiber laser (BFL) operating at room temperature is experimentally demonstrated using a 100 m long photonic crystal fiber (PCF) in conjunction with a figure-of-eight configuration. At a Brillouin pump (BP) level of 15.3 dBm, 7 simultaneous lines with 20 GHz or 0.16 nm line spacing is achieved by removing the odd-order Stokes lines. The anti-Stokes lines are also generated via four wave mixing process in the laser cavity. Compared with the Erbium-based multi-wavelength laser, this BFL has advantages in term of channel spacing and flexibility in the choice of operating wavelength. The output spectrum of the proposed BFL can be tuned by 80 nm, dependent on the availability of an appropriate BP source. The multi-wavelength BFL shows a good stability with power fluctuations of less than 0.5 dB over more than 3 h.     

Broad spectral sliced multiwavelength source with a mode locked fiber laser

A simple multi-wavelength source is demonstrated based on spectral slicing of supercontinuum (SC) light using a Sagnac loop mirror. A mode locked fiber laser with pulse width of 800 fs is employed to generate the SC in photonic crystal fiber (PCF). The SC light extending from 1200 nm up to the wavelength region above 1750 nm is obtained at the amplified pulse pump power of 30 dBm. By slicing the SC with a loop mirror, a multiwavelength comb spectrum is obtained with different channel spacing for different operating wavelength region. Spacings of 1.5, 2.3, and 2.9 nm are shown at wavelength regions of 1220, 1450, and 1730 nm, respectively. It is also observed that the signal to noise ratio (SNR) increases from 15 to 20 dB as the operating wavelength increases from 1220 to 1730 nm region.     

An experimental investigation of the gain spectrum of erbium-doped fiber amplifiers under various system configurations

The paper presents an experimental investigation of the gain spectrum of an erbium-doped fiber amplifier (EDFA) considering different system configurations, which include single-pass, double-pass, and double-pass with tunable band-pass filter (TBF). The role of TBF is to suppress the undesired amplified spontaneous emission (ASE). Both co- and counter-pumping schemes are considered with a 1480 nm laser diode as the pump and a suitable tunable laser source as the signal source. The results indicate that the signal achieves an average of 14 dB higher gain in the case of double-pass amplification with the implementation of a TBF. However, the pumping scheme hardly becomes of much importance in influencing the gain characteristics.     

基于光纤环形激光器和光放大的100 km光纤布拉格光栅传感系统

在基于掺铒光纤-拉曼混合放大的可调光纤环形激光器的光纤布拉格光栅(FBG)传感系统结构基础上,提出了延长传感距离的新方法。该方法以环形掺铒光纤激光器作为光源,采用双波长拉曼放大的方法对信号进行低噪声的双向放大,系统中间的两段掺铒光纤再利用剩余的抽运功率产生自发辐射光和放大传感信号,使得整个系统能够在超长的传感距离上获得很高的信噪比。实验表明使用一只40 mW的掺铒光纤放大(EDFA)抽运源、一只170 mW的拉曼抽运源和一只2 W的拉曼抽运源,可以使整个系统的传感距离达到100km,并且传感系统的光纤布拉格光栅反射信号均能获得超过57 dB的优良信噪比,从而实现在超长距离上的光纤布拉格光栅传感。     

Tunable single-longitudinal-mode Ytterbium all fiber laser with saturable-absorber-based auto-tracking filter

A broadband tunable, single-longitudinal-mode (SLM) Ytterbium fiber laser with unpumped Ytterbium-doped Sagnac loop is proposed and demonstrated experimentally. The unpumped Ytterbium-doped Sagnac loop is employed as a saturable absorber based auto-tracking filter to ensure single-longitudinal-mode oscillation. And a tunable band pass optical filter with large tuning range is applied to achieve broadband tuning ability. With 1-m Ytterbium-doped fiber as the gain medium, the SLM operation is achieved with over 60-nm wavelength tuning range at 160-mW pump power. The laser is very stable with output power of about 3 dBm and optical signal to noise ratio of higher than 50 dB in all the 60-nm tuning range.     

Random distributed feedback fiber laser pumped by an ytterbium doped fiber laser

A random distributed feedback fiber laser operating at 1115 nm has been demonstrated experimentally in standard communication optical fibers by using a LD-pumped Yb-doped fiber laser as the pump source. We have studied the effect of different fiber spans on this new type of random fiber laser output power. It is shown that the generation power is the highest up to 198 mW in a 50 km fiber span. The slope efficiency is more than 28.7%. Stable, high-power continuous-wave (CW) lasing can be generated when the pump power is 3.6 W. The threshold power has also been calculated which well proves a random fiber laser operating via Rayleigh scattering, amplified through the Raman scattering.     

Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

Widely tunable linear-cavity multiwavelength fiber laser with distributed Brillouin scattering

We demonstrate a multiple wavelength Brillouin/erbium fiber laser in a linear cavity configuration.The laser cavity is made up of a fiber loop mirror on one end of the resonator and a virtual mirror generated from the distributed stimulated Brillouin scattering effect on the other end.Due to the weak reflectivity provided by the virtual mirror,self-lasing cavity modes are completely suppressed from the laser cavity.At Brillouin pump and 1480-nm pump powers of 2 and 130 mW,respectively,11 channels of the demonstrated laser with an average total power of 7.13 dBm can freely be tuned over a span of 37-nm wavelength from 1530 to 1567 nm.     

Wideband wavelength tunable fiber ring laser with flattened output power spectrum

A wavelength tunable erbium-doped fiber ring laser with flattened output power spectrum over a broadband is proposed and demonstrated. The power flattening is achieved using a high-birefringence fiber loop mirror, in which a number of high-birefringence fiber sections and polarization controllers are used to get a reflection spectrum that can compensate for the output power spectrum. The wavelength tuning is realized by compressing or stretching the FBGs in the laser cavity. A 1×3 switchable fiber Bragg grating array is incorporated into the fiber ring to get a wideband tuning range of 38 nm, from 1527 to 1565 nm. Within this range, the output power uniformity is controlled within ±0.8 dB. The total output power is about 4 dBm, the 3-dB linewidth is 0.01 nm, and the side mode suppression ratio is more than 48 dB.     

Optimization of Brillouin pump wavelength location on tunable multiwavelength BEFL

Optimization of Brillouin pump (BP) wavelength location on tunable multiwavelength Brillouin-erbium fiber laser (BEFL) with BP pre-amplified technique is experimentally investigated. The tunable multiwavelength BEFL is achieved by utilization a tunable band-pass filter in a laser cavity. The optimum BP power and BP wavelength location within the filter bandwidth is determined in order to obtain the maximum stable output channels. Optimum distance of launching the BP wavelength is found at 0.80 nm shorter from the center wavelength of the filter bandwidth. 15 stable output channels are achieved from the tunable fiber laser system within the optimum range of BP power which is found to be between 5.2 to 5.7 dBm.     

基于光纤中超短脉冲非线性传输机理与特定光谱选择技术的多波长飞秒激光的产生

高集成、高可靠性宽调谐飞秒激光源在超快光谱学、量子光学及生物成像等研究与应用领域具有重要价值.如在生物多光子显微成像中,具有适中能量的宽调谐飞秒激光源不仅可满足多种生物组织荧光激发所需的峰值功率与激发波长,而且也可以显著提升非线性荧光产生效率、成像分辨率以及增大成像穿透深度.采用自主研发的高可靠性全保偏光纤飞秒激光器作为抽运源,基于低色散光纤中高峰值功率飞秒激光脉冲非线性传输引起的光谱加宽机制,本文开展了多波长全光纤飞秒激光产生技术研究.通过采用中心波长在980, 1000,1050, 1070与1100 nm的带通滤波片选择性地对单模光纤输出光谱中最左边与最右边光谱旁瓣进行滤波,在上述中心波长处分别可获得203, 195, 196, 187与194 fs的激光输出.本文提出的基于全光纤飞秒激光脉冲在单模光纤中非线性传输引起的光谱加宽机制与特定光谱选择技术的实验方案为高集成、高可靠性宽调谐飞秒激光源的实现提供了新的研究途径.     

A tunable multi-wavelength Brillouin–erbium fiber laser with fourfold Brillouin frequency spacing

We have experimentally demonstrated a tunable multi-wavelength Brillouin–erbium fiber laser with over 40 GHz spacing utilizing two cascaded double Brillouin-frequency-spacing cavities. In this laser configuration, two segments of 25 km-long single-mode fibers are used as Brillouin gain medium in each ring cavity, and a segment of 8 m-long erbium-doped fiber with 980 nm pump is employed to amplify Brillouin pump (BP). At BP wavelength of 1550 nm, BP power of 8.3 dBm (6.8 mW) and the maximum 980 nm pump power of 27.78 dBm (600 mW), seven output channels with fourfold Brillouin-frequency spacing, and the tuning range of 15 nm from 1545 to 1560 nm are achieved. The proposed multi-wavelength Brillouin–erbium fiber laser has wide applications, such as in microwave signal generation and optical communications.