Proton magnetic resonance studies of the phase structure of bulk-crystallized linear polyethylene

The broad-line proton NMR spectra of melt-crystallized samples of polyethylene covering a very wide range in molecular weight have been analyzed in terms of contributions from three components: (1) a crystalline region with crystals of orthorhombic form; (2) a noncrystalline region with liquid-like character which produces a Lorentzian contribution to the spectrum; and (3) an intermediate region in which the rotation of methylene groups about C—C bonds is partly hindered. The relative mass fractions as well as the character of these components depend greatly on the molecular weight. Samples of low molecular weight (e.g., ?30,000) are predominantly composed of lamellar crystalline regions with a minor amount of interfacial regions and no liquid-like interzonal regions. As the molecular weight increases beyond 45,000, an interzonal region with a liquid-like character associated with a higher molecular mobility is produced. Above a molecular weight of 100,000, this liquid-like character becomes pronounced with an increase in molecular mobility in the interfacial region.     

Studies on the phase structure of ethylene‐vinyl acetate copolymers by solid‐state 1H and 13C NMR

The phase structure of a series of ethylene‐vinyl acetate copolymers has been investigated by solid‐state wide‐line ¹H NMR and solid‐state high‐resolution ¹³C NMR spectroscopy. Not only the degree of crystallinity but the relative contents of the monoclinic and orthorhombic crystals within the crystalline region varied with the vinyl acetate (VA) content. Biexponential ¹³C NMR spin–lattice relaxation behavior was observed for the crystalline region of all samples. The component with longer ¹³C NMR spin–lattice relaxation time (T₁) was attributed to the internal part of the crystalline region, whereas the component with shorter ¹³C NMR T₁ to the mobile crystalline component was located between the noncrystalline region and the internal part of the crystalline region. The content of the mobile crystalline component relative to the internal part of the crystalline region increased with the VA content, showing that the ¹³C NMR spin–lattice relaxation behavior is closely related to the crystalline structure of the copolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2199–2207, 2002     

Component analysis of proton NMR spectra of linear polyethylene in the α-transition temperature range and phase distribution

Broad-line ¹H NMR spectra of linear polyethylene at temperatures in the α-transition range can be analyzed in terms of contributions from the crystalline and noncrystalline components provided molecular motion in the crystalline region is adequately considered. The spectrum of solid n-C₃₂H₆₆ or n-C₄₄H₉₀ prior to melting is used to take account of the contribution of the crystalline region of the polymer to molecular motions. The temperature dependence of the component distribution in the polymer is briefly discussed for a wide range of temperatures, together with previously reported results at low temperatures. The noncrystalline component is in a rigid glassy state at very low temperatures but with rising temperature it transforms to a mobile glassy state with restricted molecular motion, and transforms partially to the rubbery state at high temperature. The crystalline component remains rigid at low temperature, but some molecular motion is associated with it at higher temperatures in the α-transition range.     

Tetracrystalline Tetrablock Quarterpolymers: Four Different Crystallites under the Same Roof

Multicrystalline block polymers having three or more crystalline segments are essential materials for the advancement of physics in the field of crystallinity. The challenging synthesis of multicrystalline polymers has resulted in only a limited number of tricrystalline terpolymers having been reported to date. We report, for the first time, the synthesis of polyethylene‐b‐poly(ethylene oxide)‐b‐poly(?‐caprolactone)‐b‐poly(l ‐lactide) (PE‐b‐PEO‐b‐PCL‐b‐PLLA), a tetracrystalline tetrablock quarterpolymer, by combining polyhomologation, ring‐opening polymerization, and an organic/metal “catalyst switch” strategy. ¹H NMR spectroscopy and gel‐permeation chromatography confirmed the formation of the tetrablock quarterpolymer, while differential scanning calorimetry, X‐ray diffraction, and wide‐line separation solid‐state NMR spectroscopy revealed the existence of four different crystalline domains.     

Synthesis of Main‐Chain Liquid‐Crystalline Polyesters Containing Diphenyl Mesogens by Chemo‐Enzymatic Route †

Main‐chain thermotropic liquid‐crystalline polyesters containing rigid biphenyl mesogens and flexible spacers were synthesized by chemo‐enzymatic route. The enzyme‐catalyzed polymerization showed high regio‐ and chemo‐ selectivity, and is environmentally friendly. The resulting polyesters were characterized with ¹H‐NMR, ¹³C‐NMR, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and polarized light optical microscopy (POM).     

Crystallization and melting behavior of liquid crystalline copolyesters based on poly(ethylene terephthalate)

A series of copolyesters were prepared by the incorporation of p‐hydroxybenzoic acid (HBA), hydroquinone (HQ), and terephthalic acid (TA) into poly(ethylene terephthalate) (PET). On the basis of viscosity measurements, high molar mass copolyesters were obtained in the syntheses, and ¹H‐NMR analyses indicated the total insertion of comonomers. They exhibit nematic phase above melting temperature, as observed by polarized light microscope (PLM). Their crystallization and melting behaviors were also studied by differential scanning calorimetry (DSC) and wide angle X‐ray diffraction (WAXD). It was found that these copolyesters are more crystalline than copolyesters prepared from PET and HBA. Introduction of HQ/TA disrupts longer rigid‐rod sequences formed by HBA, and thus enhances molecular motion and increases crystallization rate and crystallinity. Isothermal crystallization at solid phase polymerization conditions (up to 24 h at 200°C) resulted in increased copolymer randomness (by NMR) and higher melting point, the latter attributed to structural annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 369–377, 1999     

Solid‐state NMR analyses of the crystalline–noncrystalline structure and its thermal changes for ethylene ionomers

The crystalline–noncrystalline structure and its structural changes from thermal treatments for ethylene ionomers have been investigated with solid‐state ¹³C and ²³Na NMR spectroscopy. ¹³C spin–lattice relaxation time (T_1C) measurements reveal that as‐received ethylene ionomers have much enhanced molecular mobility in the crystalline region in comparison with conventional polyethylene samples. By appropriate annealing, however, polyethylene‐like morphological features reflecting T_1C behavior can also be observed. ¹³C spin–spin relaxation time (T_2C) measurements for the noncrystalline region reveal the existence of two components with different T_2C values, and these two components have been assigned to the crystalline–amorphous interfacial and rubbery–amorphous components. These results indicate that the structure of the major part of the noncrystalline region in the ethylene ionomers is similar to that of bulk‐crystallized polyethylene samples, regardless of possible ionic aggregates. The origin of the lower temperature endothermic peak in the heating process of the differential scanning calorimetry curve observed for the as‐received sample has also been examined somewhat in detail. As a result, it is proposed that the melting of smaller crystallites produced during storage at room temperature is the origin of the lower temperature peak. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1142–1153, 2002     

Polyethylene Aerogels with Combined Physical and Chemical Crosslinking: Improved Mechanical Resilience and Shape‐Memory Properties

While the introduction of polymers into aerogels strongly enhances their toughness, truly elastic monolithic aerogels which restore their dimensions upon extensive compression are still challenging to synthesize. In this context hydrophobic semi‐crystalline polymers with low glass transition temperatures, and combined stiffness and flexibility, have only recently attracted attention. Shown here is that polyethylene aerogels with a low density, and combined chemical crosslinking and high crystallinity, display high moduli and excellent mechanical resilience. To maximize the crystallinity of these aerogels while maintaining a high crosslinking density, polyethylene networks with well‐defined segments were synthesized by hydrosilylation crosslinking of telechelic, vinyl‐functionalized oligomers obtained from catalyzed chain‐growth polymerization. Recoverable deformations both above and below the melting temperature of polyethylene affords remarkable shape‐memory properties.     

室温下聚乙烯及其共聚物的相结构动态变化

采用固体高分辨＾１３ＣＣＰ／ＭＡＳ方法跟踪测量了熔融淬火的聚乙烯样品及冷冻抽干的乙烯共聚物样品的相态结构在室温下随时间的变化，通过计算机拟合，观察到两种样品中的单斜晶、斜方晶并对该现象产生的机制给予了解释。     

Synthesis of amphiphilic linear‐hyperbranched graft‐copolymers via grafting based on linear polyethylene backbone

The synthesis of amphiphilic linear‐hyperbranched graft‐copolymers in a grafting‐from approach is reported. The linear polyethylene with terminated hydroxyls, prepared by copolymerization of ethylene and 10‐undecen‐1‐ol, was used as macroinitiator for ring‐opening multibranching polymerization of glycidol by a typical slow monomer addition approach. Successful attachment of the hyperbranched grafts to the linear polyethylene backbone was confirmed by ¹H/¹³C NMR, GPC, and TGA. The degree of polymerization and M_w/M_n of hyperbranched grafts were efficiently controlled by temperature, deprotonation ratio as well as the molar ratio of glycidol/hydroxyl (N_glycidol/N_OH). The complicated microstructures caused by unsymmetric glycidol structure were analyzed by DEPT and 2D HSQC spectra, the degree of branching of 0.63–0.66 were calculated, indicating the extent of branch is close to theoretical values. The thermal analysis of linear‐hyperbranched copolymers via TGA and DSC is also presented. To our knowledge, this is the first report of a linear‐hyperbranched graft‐copolymer with a crystalline and nonpolar linear‐polyethylene segment. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2146–2154     

无机/有机复合载体负载乙酰丙酮铁/双亚胺基吡啶催化剂及其乙烯聚合

采用溶胶-凝胶法,将苯乙烯-丙烯酸共聚物(PSA)包覆于955 Davison硅胶上得到无机/有机复合微球载体,并在2,6-二[1-(2-异丙基苯基亚胺基)乙基]吡啶/Fe(acac)3均相催化剂中浸渍后得到负载型双亚胺基吡啶铁催化剂.该催化剂在生产高结晶度(72%)聚乙烯的同时,还能生产一定量的α-烯烃.考察了不同膜材料以及聚合条件(不同助催化剂,压力,温度,Al/Fe摩尔比)对聚合活性以及聚合产物性能的影响,发现温度对聚合产物的α-烯烃与聚乙烯的质量比影响最大,助催化剂类型既影响催化剂的活性,也对最终产物的性质有着很大的影响.氯化镁处理的PSA作为膜材料时,负载2,6-二[1-(2-异丙基苯基亚胺基)乙基]吡啶/Fe(acac)3所得到聚乙烯分子量较低(Mw=11.9×104),结晶度较大(72%),熔融指数MI较高(2.35 g/10min),可作为双峰聚乙烯中的低分子量部分加以利用.     

A study of wet PVC gels by raman spectroscopy

Raman spectroscopy has been used to study PVC gels made in cyclohexanone in the wet state at concentrations from 21 to 93% by weight of PVC. Parallel and perpendicular spectra were obtained in the C-Cl stretching region, and after subtraction of the solvent spectrum they were analyzed into a set of overlapping peaks due to various structural components. The positions of the peaks found were in good agreement with those found earlier for PVC samples in the solid state. The fractional contribution of the areas of peaks assigned to crystalline material to the total area under the C-Cl stretching region was used to estimate the crystallinity of the gels, and changes in their depolarization ratios and relative intensities were interpretated as providing further evidence for the presence of two types of crystallites in PVC gels. From a determination of the crystallinity at the gel transition point and reasonable assumptions, the contributions of the two types of crystallites to the total crystallinity were estimated.     

An NMR investigation on the phase structure and molecular mobility of the novel exfoliated polyethylene/palygorskite nanocomposites

Novel exfoliated polyethylene (PE)/palygorskite nanocomposites prepared by in situ polymerization are characterized by solid‐state nuclear magnetic resonance (NMR). The phase structure and molecular mobility are investigated by a combination of proton and carbon NMR. The results showed that incorporation of small amounts of palygorskite had great influence on the phase structure and molecular mobility. The incorporated palygorskite hindered the crystallization process and introduced motion‐hindered chains in the NMR crystalline and amorphous phase. ¹³C cross‐polarization and magic‐angle spinning NMR revealed two orthorhombic crystalline phase with different line‐width. The chain mobility of orthorhombic crystalline phase with broad resonance line is obviously hindered compared with the phase with narrow resonance line when the filler is introduced. Additionally, the results of pulsed field gradient NMR technique show those the tortuosities in the nanocomposites are much higher than that in the bulk PE. The self‐diffusion process of probe molecules is also influenced by the palygorksite load. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1363–1371, 2010     

Crystalline structure of polyamide 12 as revealed by solid‐state 13C NMR and synchrotron WAXS and SAXS

The crystalline structure of polyamide‐12 (PA12) was studied by solid‐state ¹³C nuclear magnetic resonance (NMR) as well as by synchrotron wide‐ and small‐angle X‐ray scattering (WAXS and SAXS). Isotropic and oriented PA12 showed different NMR spectra ascribed to γ‐ and γ′‐crystalline modifications, respectively. On the basis of the position of the first diffraction peak, the isotropic γ‐form and the oriented γ′‐form were shown to be with hexagonal crystalline lattice at room temperature. When heated, the two PA12 polymorphs demonstrated different behaviors. Above 140 °C, the isotropic γ‐PA12 partially transformed into α‐modification. No such transition was observed with the oriented γ′‐PA12 phase even after annealing at temperatures close to melting. A γ′–γ transition was observed here only after isotropization by melting point. Various structural parameters were extracted from the WAXS and SAXS patterns and analyzed as a function of temperature and orientation: the degree of crystallinity, the d‐spacings, the Bragg's long spacings, the average thicknesses of the crystalline (l_c) and amorphous (l_a) phases, and the linear crystallinity x_cl within the lamellar stacks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3720–3733, 2005     

Melt‐processable poly(oxyphenylalkanoate): Synthesis,properties, and in vitro degradation of poly(4‐oxyphenylacetate)

The homopolyester of 4‐hydroxyphenylacetic acid (HPAA) was synthesized by one‐pot, slurry‐melt, and acidolysis melt polymerization techniques and was characterized by its inherent viscosity and IR and NMR spectra. Differential scanning calorimetry (DSC), polarizing light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD) studies of the homopolymer were carried out for its thermal and phase behavior. The results indicated that the yield and molecular weight of the polymer depended on the method of preparation; moreover, the acidolysis melt polymerization of the pure acetoxy derivative of HPAA was the best method for the preparation of high molecular weight poly(4‐oxyphenylacetate) (polyHPAA) without side reactions. DSC and PLM studies also showed that the thermal and optical properties depended largely on the polymerization conditions and inherent viscosity values. PolyHPAA did not show a clear texture typical of liquid‐crystalline polymers, whereas after cooling from the melt, structures similar to spherulitic crystals were observed. WAXD patterns showed a crystalline nature. The in vitro degradability of the polymer was also studied via the water absorption in buffer solutions of pH 7 and 10 at 30 and 60 °C; this was followed by Fourier transform infrared, inherent viscosity, DSC, thermogravimetric analysis, WAXD, and scanning electron microscopy techniques. Unlike Vectra®, which showed no degradation, polyHPAA showed an increase in hydrolytic degradation from 5.0 and 6.0% at 30 °C to 12.5 and 15.0% at 60 °C after 350 h in buffer solutions of pH 7 and 10, respectively. The results indicated a possible biomedical prosthetic application of poly(oxyphenylalkanoate)s such as polyHPAA with better crystallinity coupled with degradability as a substitute for poly(hydroxyalkanoates). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2430–2443, 2001     

Microinjection molding of polyamide 6

Processing polymers by microinjection molding (μIM) generate specific constraints upon the polymer melt such as high shear stress and rapid cooling, leaving a mark upon the microstructure of the micropart. The present work compares the morphology and structure of polyamide 6 samples produced by melt extrusion and μIM. The specimens obtained were analyzed by polarized light microscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. α and γ crystalline forms were formed in polyamide 6 samples prepared by both methods. The γ form was dominant in the skin of the microinjection molded part, with larger contribution for these samples compared with extruded samples. The conditions used in μIM lead to considerable orientation at the skin region, decreasing toward the core, while the extruded samples showed almost no orientation. The overall degree of crystallinity of the microinjection molded part was lower compared with the extruded sample. Copyright © 2014 John Wiley & Sons, Ltd.     

A 13C NMR study of the effect of γ-irradiation on the chain dynamics of poly(ethylene oxide)

A comparison of solid-state ¹³C nuclear magnetic resonance (NMR) spectra of virgin and vacuum γ-irradiated poly (ethylene oxide) (PEO) evidences marked differences. The unirradiated PEO shows a well-resolved amorphous resonance and a weak, broad envelope of crystalline resonances, while the irradiated PEO presents well-resolved resonances for both the crystalline and amorphous carbons. Upon recrystallization from the melt both PEO samples yield solid-state ¹³C NMR spectra that are closely similar to that of the virgin, unheated sample. Observation of both melt-recrystallized samples at ?60°C yields similar spectra with well-resolved crystalline resonances. Crosslinking is the predominant chemical change occurring during the γ-irradiation of PEO under vacuum and produces a change in the motional character of the crystalline phase. This change is not the result of a reduction in crystallinity as evidenced by differential scanning calorimetry (DSC) observations. The most probable explanation is that the crosslinks are concentrated at the surface of the crystalline lamellae with a resultant change in the low frequency molecular motions of the crystalline chains. This motional change shifts the T_1p^H such that the crystalline carbon nuclei can now be cross-polarized at room temperature and the resonance linewidth is reduced. Following melting and recrystallization the motional characteristics of the irradiated PEO are nearly identical to those of the unirradiated sample, probably as a result of a redistribution of the crosslinks throughout the amorphous phase during recrystallization.     

Single and binary catalyst systems based on nickel and palladium in polymerization of ethylene

The catalyst (N,N‐bis(2,6‐dibenzhydryl‐4‐ethoxyphenyl)butane‐2,3‐diimine)nickel dibromide, a late transition metal catalyst, was prepared and used in ethylene polymerization. The effects of reaction parameters such as polymerization temperature, co‐catalyst to catalyst molar ratio and monomer pressure on the polymerization were investigated. The α‐diimine nickel‐based catalyst was demonstrated to be thermally robust at a temperature as high as 90 °C. The highest activity of the catalyst (494 kg polyethylene (mol cat)^?1 h^?1) was obtained at [Al]/[Ni] = 600:1, temperature of 90 °C and pressure of 5 bar. In addition, the performance of a binary catalyst using nickel‐ and palladium‐based complexes was compared with that of the corresponding individual catalytic systems in ethylene polymerization. In a study of the catalyst systems, the average molecular weight and molecular weight distribution for the binary polymerization were between those for the individual catalytic polymerizations; however, the binary catalyst activity was lower than that of the two individual ones. The obtained polyethylenes had high molecular weights in the region of 10⁵ g mol^?1. Gel permeation chromatography analysis showed a narrow molecular weight distribution of 1.44 for the nickel‐based catalyst and 1.61 for the binary catalyst system. The branching density of the polyethylenes generated using the binary catalytic system (30 branches/1000 C) was lower than that generated using the nickel‐based catalyst (51/1000 C). X‐ray diffraction study of the polymer chains showed higher crystallinity with lower branching of the polymer obtained. Also Fourier transform infrared spectra confirmed that all obtained polymers were low‐density polyethylene.     

Promotion of the γ‐phase of polyamide 6 in its nanocomposite with phosphate glass

The effect of tin fluorophosphate‐glass (Pglass) nanoparticles on the polyamide‐6 (PA6) matrix in Pglass/PA6 hybrids has been investigated by ¹³C solid‐state nuclear magnetic resonance (NMR). The crystallinity determined by direct‐polarization ¹³C NMR combined with longitudinal relaxation‐time (T_1C) filtering varied between 31 and 44%. T_1C‐filtered ¹³C spectra with cross polarization clearly showed resonances of both the α‐ and γ‐crystalline phases of PA6, typically at ratios near 45:55, while the similarly processed neat polymer contained only the α‐phase. This suggests that the Pglass promotes the growth of the γ‐crystalline phase. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 857–860, 2008     

Ammonolysis of 1,2‐Bis[dichloro(methyl)silyl]ethane. On the Structure of 1,3,6,8‐Tetramethyl‐2,7,11,12‐tetraaza‐1,3,6,8‐tetrasila‐tricyclo[6.2.1.13,6]‐dodecane

Ammonolysis of 1,2‐bis[dichloro(methyl)silyl]ethane afforded a crystalline tricyclic silazane along with polymeric material. The crystalline material could be isolated in pure state. It was analyzed by ¹H, ¹³C, ¹⁵N and ²⁹Si NMR spectroscopy in solution, by ¹³C, ¹⁵N and ²⁹Si MAS NMR spectroscopy in the solid state, as well as by single‐crystal and powder X‐ray diffraction. The title compound exists as a single isomer in solution, whereas in the solid state the presence of several modifications is indicated, in particular by the solid‐state MAS NMR spectra.