Bismuth nano-powder electrode for trace analysis of heavy metals using anodic stripping voltammetry

In the present work, a more sensitive and conveniently usable electrode sensor for a trace analysis of heavy metal was developed by using Bi nanopowder synthesized by levitational gas condensation (LGC) method. It was observed from the TEM image that the Bi nanopowder is spherical in shape with a size of nearly 50 nm. The XRD pattern revealed intense peaks which can be indexed as a rhombohedral structure of Bi without any other diffraction peaks corresponding to an oxide or an impurity. This indicates that the resulting nanopowder synthesized by the LGC method is a highly crystallized Bi with a high purity. The square wave anodic stripping voltammograms (SWASV), experimentally measured for the Bi nanopowder electrode, showed well-defined and highly reproducible electrochemical responses relating to the stripping of Cd and Pb. The detection limit of the electrode was estimated to be 0.15 μg/l and 0.07 μg/l for Cd and Zn, respectively, on the basis of the signal-to-noise characteristics (S/N = 3) of the response for the 1.0 μg/l solution under a 10 min accumulation.     

A voltammetric sensor for simultaneous determination of lead,cadmium and zinc on an activated carbon fiber rod

A simple, low cost and sensitive voltammetric sensor was developed for the simultaneous detection of Pb²⁺, Cd²⁺, and Zn²⁺ based on a disposable carbon fiber rod (CFR). The important factors to enhance the sensing property were creation of a clean surface by dealing with CFR at a high potential and electrochemical deposition of Bi film to improve the accumulation of heavy metal ions.     

Signal enhancement in solution-cathode glow discharge — optical emission spectrometry via low molecular weight organic compounds

HCOOH, CH₃COOH, and CH₃CH₂OH were used as chemical modifiers in a solution-cathode glow discharge. Emission was measured directly from the discharge, without a gas–liquid separator or a secondary excitation source. Emission from Ag, Se, Pb, and Hg was strongly enhanced, and the detection limits (DL) for these elements were improved by up to an order of magnitude using a combination of HCOOH and HNO₃ compared to using HNO₃ alone. The DL was measured for Mg (1 μg/L), Fe (10 μg/L), Ni (6 μg/L), Cu (6 μg/L), Pb (1 μg/L), Ag (0.1 μg/L), Se (300 μg/L), and Hg (2 μg/L). Coefficients of determination (R²) were between 0.9986 and 0.9999. A voltage of 1 kV was used, which produced a current of approximately 70 mA.     

Microwave-radiated synthesis of gold nanoparticles/carbon nanotubes composites and its application to voltammetric detection of trace mercury(II)

Gold nanoparticles/carbon nanotubes (Au-NPs/CNTs) composites were rapidly synthesized by microwave radiation, and firstly applied for the determination of trace mercury(II) by anodic stripping voltammetry (ASV). The structure and composition of the synthesized Au-NPs/CNTs nanocomposites were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), UV–vis absorption spectroscopy and cyclic voltammetry. Au-NPs/CNTs nanocomposites modified glassy carbon electrode (Au-NPs/CNTs/GCE) exhibited excellent performance for Hg(II) analysis. A wide linear range (5 × 10⁻¹⁰–1.25 × 10⁻⁶ mol/L) and good repeatability (relative standard deviation of 1.84%) were obtained for Hg(II) detection. The limit of detection was found to be 3 × 10⁻¹⁰ mol/L (0.06 μg/L) at 2 min accumulation, while the World Health Organization’s guideline value of mercury for drinking water is 1 μg/L, suggesting the proposed method may have practical utility.     

Bismuth nanosheets grown on carbon fiber cloth as advanced binder-free anode for sodium-ion batteries

The bismuth nanosheets grown on carbon fiber cloth were designed. For sodium-ion batteries, the Bi/CFC electrode exhibited a high reversible capacity of 350 and 240 mAh g^− 1 after 300 cycles at 50 and 200 mA g^− 1, as well as a good rate capability. Besides, the electrode displayed two flat potential profiles during the charge/discharge process. The results suggest that the Bi/CFC electrode has excellent potential as an anode for sodium-ion batteries.     

Simultaneous determination of metal ions as complexes of pentamethylene dithiocarbamate in Indus river water,Pakistan

River water samples before and after mixing with industrial effluents were collected at an interval of 4 weeks for one year and analyzed for simultaneous determination of Fe³⁺, Cr³⁺, Mn²⁺, Cu²⁺, Ni²⁺and Co²⁺ after preconcentration using pentamethylene dithiocarbamate (PMDTC) as derivatizing reagent and subsequent solvent extraction by high performance liquid chromatography (HPLC). The average levels (n = 12) of metal ions were found in the range of 14.2–542 μg/L. The results were then compared with a standard flame atomic absorption spectrophotometric method revealed no significant differences.     

Electrospun zirconia-embedded carbon nanofibre for high-sensitive determination of methyl parathion

Carbon nanofibers embedded with ultrafine zirconia nanoparticles (ZrO₂-CNFs) are fabricated via a new methodology. Polyvinylpyrrolidone (PVP) and polymethylmethacrylate (PMMA) binary polymers containing zirconium n-butoxide are first dissolved in dimethylformamide, and the resulting solution is electrospun and heat-treated. The tetragonal zirconia nanoparticles formed, with a size of 5 ± 2 nm in diameter, are uniformly distributed in the carbon nanofibres. Using Nafion as an additive, ZrO₂-CNFs are drop-cast onto the glassy carbon electrode (ZrO₂-CNF/GCE) and the modified electrode is then applied to detect methyl parathion (MP) using differential pulse voltammetry. Two linear relationships are found at the concentration ranges of 1 × 10^− 9–2 × 10^− 8 g/L and 2 × 10^− 8–2 × 10^− 7 g/L, with a detection limit of 3.4 × 10^− 10 g/L (S/N > 3). The electrospun-based ZrO₂-CNF is a very promising coating material for electrochemical sensing of organophosphorus compounds.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.     

Determination of tannic acid by adsorptive anodic stripping voltammetry at porous pseudo-carbon paste electrode

A novel and sensitive electrochemical sensor based on porous pseudo-carbon paste electrode (PPCPE) for tannic acid detection is described. PPCPE is fabricated by mixing calcium carbonate microspheres as the template, graphite powders as the filler, and pyrrole as the precursor of polymer which actually acted as the paste. After the polymerization of pyrrole catalyzed by Fe³⁺, the template calcium carbonate microspheres are removed with 0.1 M hydrochloric acid to form PPCPE. The diameters of these pores are in the range from 2 to 5 μm by SEM observations and the specific surface area of PPCPE is 59.26 m²/g by the Brunauer–Emmet–Teller (BET) method. A linear relationship between the anodic stripping peak current and the concentration of tannic acid from 0.02 to 1 μM and a limit of detection as low as 0.01 μM are obtained using PPCPE.     

Mesoporous silica thin films for molecular sieving and electrode surface protection against biofouling

Electrode fouling is a major challenge for the long term use of sensors in real samples as it leads to the decay of the electroanalytical signal and is often caused by the formation of an inhibiting layer formed by biomolecules. We demonstrate here that ordered and vertically aligned mesoporous silica generated at the surface of an indium tin oxide electrode by electrochemically assisted self-assembly act as a molecular sieve and a protective layer for the electrode surface. They indeed prevent the adsorption of size excluded large undesired molecules (e.g. haemoglobin) while allowing the detection of small redox active molecules likely to reach the electrode surface through the film (e.g. propranolol) with almost no loss of sensitivity. At a bare electrode, the oxidation of propranolol is completely inhibited in the presence of 5 μM haemoglobin. At a modified electrode, the sensitivity for propranolol in the absence of haemoglobin is (72.8 ± 2.9) mA mol^− 1 (R² = 0.992, N = 7) and it remains similar in the presence of 5 μM haemoglobin with a value of (67.4 ± 7.2) mA mol^− 1 (R² = 0.992, N = 7).     

Direct determination of arsenate based on its electrocatalytic reduction at the poly(aniline-co-o-aminophenol) electrode

It was found that the copolymer poly(aniline-co-o-aminophenol) (PANOA) can strongly catalyze the reduction of arsenate in a NaCl solution, which was proved by cyclic voltammetry and the determination of activation energy. On the basis of the electrocatalytic reduction of arsenate, the PANOA copolymer was used as a probe to determine directly arsenate. The electrocatalytic activity of the PANOA electrode toward As(V) reduction strongly depended on the pH and the applied potential. Under the optimal conditions, the PANOA electrode can be used to determine directly As(V) concentration in a wide linear range (n = 19) of 0.949 and 495 μM with a correlation coefficient of 0.995 and a limit of detection of 0.495 μM. The sensitivity of the electrode was 0.192 μA μM^?1 cm^?2. The PANOA electrode had the good storage stability and a less negative operation potential of ?0.15 V (vs. SCE).     

Construction of an amperometric biosensor for xanthine via supramolecular associations

Xathine oxidase was chemically modified with β-cyclodextrin-branched carboxymethylcellulose and further supramolecularly immobilized on a gold electrode, previously coated with a monolayer of 1-adamantanyl residues. The electrode was employed for constructing an amperometric biosensor device, which showed linear response (poised at +700 mV vs. Ag/AgCl) toward xanthine concentration between 300 μM and 10.4 mM at pH 7.0. The biosensor reached 95% of steady-state current in about 14 s and its sensitivity was 8.2 mA/M cm². The enzyme electrode retained 93% of its initial activity after 3 weeks of storage at 4 °C in 50 mM sodium phosphate buffer, pH 7.0. The supramolecular nature of the immobilization approach was confirmed by cyclic voltammetry.     

Electrochemical performance of a three-layer electrode based on Bi nanoparticles,multi-walled carbon nanotube composites for simultaneous Hg(II) and Cu(II) detection

Electrochemical analysis is a promising technique for detecting biotoxic and non-biodegradable heavy metals. This article proposes a novel composite electrode based on a polyaniline (PANi) framework doped with bismuth nanoparticle@graphene oxide multi-walled carbon nanotubes (Bi NPs@GO-MWCNTs) for the simultaneous detection of multiple heavy metal ions. Composite electrodes are prepared on screen-printed electrodes (SPCEs) using an efficient dispensing technique. We used a SM200SX-3A dispenser to load a laboratory-specific ink with optimized viscosity and adhesion to draw a pattern on the work area. The SPCE was used as substrate to facilitate cost-effective and more convenient real-time detection technology. Electrochemical techniques, such as cyclic voltammetry and differential pulse voltammetry, were used to demonstrate the sensing capabilities of the proposed sensor. The sensitivity, limit of detection, and linear range of the PANi-Bi NPs@GO-MWCNT electrode are 2.57 × 10² μA L μmol⁻¹ cm⁻², 0.01 nmol/L, and 0.01 nmol/L–5 mmol/L and 0.15 × 10⁻¹ μA L μmol⁻¹ cm⁻², 0.5 nmol/L, and 0.5 nmol/L–5 mmol/L for mercury ion (Hg(II)) and copper ion (Cu(II)) detection, respectively. In addition, the electrode exhibits a good selectivity and repeatability for Hg(II) and Cu(II) sensing when tested in a complex heavy metal ion solution. The constructed electrode system exhibits a detection performance superior to similar methods and also increases the types of heavy metal ions that can be detected. Therefore, the proposed device can be used as an efficient sensor for the detection of multiple heavy metal ions in complex environments.     

Amperometric enzyme biosensor for hydrogen peroxide via Ugi multicomponent reaction

A novel strategy based on the Ugi multicomponent reaction was employed for immobilizing horseradish peroxidase on sodium alginate-coated gold electrode. The electrode was employed for constructing an amperometric biosensor device using 1 mM hydroquinone as electrochemical mediator. The electrode showed linear response (poised at −300 mV vs Ag/AgCl) toward H₂O₂ concentration between 70 μM and 8.8 mM at pH 7.0. The biosensor reached 95% of steady-state current in about 12 s and its sensitivity was 33.8 mA/M cm². The electrode retained full initial activity after 30 days of storage at 4 °C in 50 mM sodium phosphate buffer, pH 7.0.     

Novel poly (neutral red) nanowires as a sensitive electrochemical biosensing platform for hydrogen peroxide determination

Poly (neutral red) nanowires (PNRNWs) have been synthesized for the first time by the method of cyclic voltammetric electrodeposition using porous anodic aluminum oxide (AAO) template and were examined by scanning electron microscopy (SEM) and transmission electron microscope (TEM). Moreover, horseradish peroxidase (HRP) was encapsulated in situ in PNRNWs (denoted as PNRNWs–HRP) by electrochemical copolymerization for potential biosensor applications. The PNRNWs showed excellent efficiency of electron transfer between the HRP and the glassy carbon (GC) electrode for the reduction of H₂O₂ and the PNRNWs–HRP modified GC electrode showed to be excellent amperometric sensors for H₂O₂ at −0.1 V with a linear response range of 1 μM to 8 mM with a correlation coefficient of 0.996. The detection limit (S/N = 3) and the response time were determined to be 1 μM and <5 s and the high sensitivity is up to 318 μA mM⁻¹ cm⁻².     

Anti-Cancer Effect of Kaffir Lime (Citrus Hystrix DC) Leaf Extract in Cervical Cancer and Neuroblastoma Cell Lines

Previous study showed that kaffir lime leaf contains alkaloid, flavonoid, terpenoid, tannin and saponin. The objective of this study was to examine the cytotoxic effect of kaffir lime leaf extract on cervical cancer and neuroblastoma cell lines. The method used for this research to determine cell viability was an 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. Results showed that an ethyl acetate extract had an IC50 for HeLa cells, UKF-NB3, IMR-5 and SK-N-AS parental cells of 40.7 μg · mL^–1, 28.4 μg · mL^–1, 14.1 μg · mL^–1, and 25.2 μg · mL^–1 respectively. Furthermore, the IC50 of chloroform extracts for HeLa cells, UKF-NB3, IMR-5 and SK-N-AS parental were 17.6 μg · mL^–1, 18.9 μg · mL^–1, 6.4 μg · mL^–1, and 9.4 μg · mL^–1 respectively. These data showed that kaffir lime extract reduces the viability of cervical and neuroblastoma cell lines and may have potential as anti-cancer compounds.     

3D patterning of silicon by contact etching with anodically biased nanoporous gold electrodes

A novel strategy to achieve 3D pattern transfer into silicon in a single step without using lithography is presented. Etching is performed electrochemically in HF media by contacting silicon with a positively biased, patterned, metal electrode. Dissolution is localized at the Si/metal contacts and patterning is obtained as the electrode digs into the substrate. Previous attempts at imprinting Si using bulk metal electrodes have been limited by electrolyte blockage. Here, the problem is solved by using, for the first time, a nanoporous metal electrode that allows the electrolyte to access the entire Si/metal interface, irrespective of the electrode dimensions. As a proof of concept, imprinting of well-defined arrays of inverted pyramids has been performed with sub-micrometer spatial resolution over 1 mm² using a nanoporous gold electrode of the complementary shape. Under a polarization of + 0.3 V/SME in 5 M HF, the etch rate is ~ 0.5 μm min^− 1. The pyramidal pattern is imprinted independently of the Si crystallographic orientation. This maskless imprinting technique opens new opportunities in the fabrication of Si microstructures.     

Direct electrochemistry of myoglobin based on DNA accumulation on carbon ionic liquid electrode

Poly-anionic deoxyribonucleic acid (DNA) was accumulated on the positively charged surface of carbon ionic liquid electrode (CILE) with N-butylpyridinium hexafluorophosphate (BPPF₆) as binder, and then myoglobin (Mb) was immobilized onto the DNA film by electrostatic interaction to form Mb/DNA/CILE electrode. The direct electrochemistry of Mb was then investigated in detail. A pair of well-defined, quasi-reversible cyclic voltammetric peaks of Mb was obtained with the formal potentials (E⁰′) at ?0.304 V (vs. SCE) in phosphate buffer solution (PBS, pH 7.0). The Mb/DNA/CILE electrode showed excellent electrocatalytic activity to H₂O₂ and trichloroacetic acid (TCA) in the range of 1.0–160 μmol/L and 0.5–40.0 mmol/L, respectively. The apparent Michaelis–Menten constants (K_M) toward H₂O₂ and TCA were calculated as 0.42 and 0.82 mmol/L. So, the DNA/CILE had potential to study other proteins.     

A new composite electrode of Ni-Ferrite/TiOx/Si(111): Preparations and photoelectrochemical studies

A composite electrode of Ni-ferrite/TiO_x/Si(111) was synthesized by grafting Ni²⁺Fe²⁺Fe³⁺–LDH–TiCl₃ (LDH: Layered Double Hydroxides) on n-Si(111) surface and calcined under 1100 °C. Photoelectric research results indicated that the electrode had good photovoltaic effects in an electrolyte solution containing 7.6 M HI and 0.05 M I₂, while platinum plate was used as counter-electrode. The observed photo-voltages (U_pv) and photocurrent densities (j_pc) of the electrode were at ?0.75 V and 5.35 mA/cm², respectively. Compared with electrodes of oxidized n-Si(111) crystal and n-Si(111) wafer covered by Ni-ferrites, j_pc of the electrode Ni-ferrite/TiO_x/Si(111) was increased greatly.     

Evaluation of tungsten–rhodium coating on an integrated platform as a permanent chemical modifier for cadmium,lead, and selenium determination by electrothermal atomic absorption spectrometry

A tungsten–rhodium coating on the integrated platform of a transversely heated graphite atomizer is proposed as a permanent chemical modifier for the determination of Cd, Pb, and Se by electrothermal atomic absorption spectrometry. It was demonstrated that coating with 250 μg W+200 μg Rh is as efficient as the conventional Mg(NO₃)₂+NH₄H₂PO₄ or Pd+Mg(NO₃)₂ modifiers for avoiding most serious interferences. The permanent W–Rh modifier remains stable for 300–350 firings of the furnace, and increases tube lifetime by 50%–100% when compared to pyrolytic carbon integrated platforms. Also, there is less degradation of sensitivity during the atomizer lifetime when compared with the conventional modifiers, resulting in a decreased need of re-calibration during routine analysis. The characteristic masses and detection limits achieved using the permanent modifier were respectively: Cd 1.1±0.4 pg and 0.020 μgL⁻¹; Pb 30±3 pg and 0.58 μgL⁻¹ and Se 42±5 pg and 0.64μgL⁻¹. Results from the determination of these elements in water reference materials were in agreement with the certified values, since no statistical differences were found by the paired t-test at the 95% level.