Fabrication of Tb0.3Dy0.7Fe2/epoxy composites: Enhanced uniform magnetostrictive and mechanical properties using a dryprocess

To improve the uniformity of the magnetostrictive properties of Terfenol-D composites along the field direction, a dry method is developed in the present study. We examined the compaction pressure, particle volume fraction, particle size and composite configuration as factors that affected the magnetostrictive properties of the composites. The experimental results indicated that the magnetostrictive properties were improved with the increase of compaction pressure and particle volume fraction. In addition, larger average particle size was shown to result in more pronounced magnetostrictive properties. The particle alignment due to the orientation field is beneficial for the promotion of the magnetostrictive properties. The largest saturation magnetostriction and the maximum piezo-magnetic coefficient in the absence of a mechanical preload was obtained at 1005 ppm and 4.08 nm/A, respectively, for the aligned composite including a particle volume fraction of 77% and an average particle size of 210 μm.     

Magnetostrictive properties of titanate coupling agent treated Terfenol-D composites

As a kind of composites, the bond strength between the polymer matrix and the Terfenol-D particles affects the performance of magnetostrictive composites. By observing the fracture morphologies, the bond strength of the magnetostrictive composites prepared with untreated Terfenol-D was proved weak. Titanate coupling agent was used for particles to improve the bond strength. Contact angle analysis indicates the work of adhesion of the epoxy resin to the treated Terfenol-D is larger than that to the untreated Terfenol-D. Different magnetostrictive composites with 20%, 35% and 50% particle volume fractions were prepared with treated and untreated Terfenol-D particles. Their static and dynamic magnetostriction was tested without pre-stress at room temperature. The results indicate titanate coupling agent treating increases the magnetostrictive properties of magnetostrictive composites, that is probably because the bond strength improves due to the particle treating.     

Predicting performance of polymer-bonded Terfenol-D composites under different magnetic fields

Considering demagnetization effect, the model used to calculate the magnetostriction of the single particle under the applied field is first created. Based on Eshelby equivalent inclusion and Mori-Tanaka method, the approach to calculate the average magnetostriction of the composites under any applied field, as well as the saturation, is studied by treating the magnetostriction particulate as an eigenstrain. The results calculated by the approach indicate that saturation magnetostriction of magnetostrictive composites increases with an increase of particle aspect and particle volume fraction, and a decrease of Young's modulus of the matrix. The influence of an applied field on magnetostriction of the composites becomes more significant with larger particle volume fraction or particle aspect. Experiments were done to verify the effectiveness of the model, the results of which indicate that the model only can provide approximate results.     

Mössbauer study of new functional metal/polymer nanocomposites with spatially oriented FeGa particles

Mössbauer spectroscopy has been applied to study the structure and magnetostriction interdependence of metall/polymer composites with spatially oriented FeGa particles in a polymer matrix. Composites were synthesized combining modified polyurethane with nanocrystalline mechanosynthesized particles of magnetostrictive FeGa composition through polymerization to achieve a considerable magnetostrictive response. To increase magnetoelastic effects a spatial particle arrangement in the polymer matrix was generated. The magnetostrictive composition of the mechanosynthesized particles has been determined by Mössbauer spectroscopy, X-ray diffraction and TEM at different stages of ball milling. The microstructure of the composites via the particle orientation in the polymer has been researched by SEM and Conversion Mössbauer spectroscopy with the registration of resonant X-rays. The spatial particle inhomogeneity and magnetic anisotropy have been analyzed in order to reveal the factors determining the functional properties of the manufactured composites. Three-fold enhancement of the magnetostrictive response for FeGa/polyurethane composites with non-standard magnetic anisotropy has been demonstrated.     

Enhancement of the thermal properties of silver-diamond composites with chromium carbide coating

The present work reports the enhancement of the thermal properties in Ag/diamond matrix composites reinforced with chromium carbide coated diamond particles. The coated diamond particles were characterized by x-ray diffraction, x-ray photoelectron spectroscopy and Raman spectra. The composites were synthesized by spark plasma sintering. The chromium carbide coating on the diamond particles resulted in composites exhibiting improved wettability and strong interfacial bonding between the diamond particles and Ag matrix. The composites with coated diamonds showed a low coefficient of thermal expansion of 8.24 × 10^?6/K and a high thermal conductivity of 695 W/mK at 60 % particle volume fraction, which greatly outperformed the composites with uncoated diamonds at the same particle volume fraction. The obtained results are useful for synthesizing Ag/diamond composites with greatly improved thermal performance.     

Effects of particle/matrix interface and strengthening mechanisms on the mechanical properties of metal matrix composites

A randomly distributed multi-particle model considering the effects of particle/matrix interface and strengthening mechanisms introduced by the particles has been constructed. Particle shape, distribution, volume fraction and the particles/matrix interface due to the factors including element diffusion were considered in the model. The effects of strengthening mechanisms, caused by the introduction of particles on the mechanical properties of the composites, including grain refinement strengthening, dislocation strengthening and Orowan strengthening, are incorporated. In the model, the particles are assumed to have spheroidal shape, with uniform distribution of the centre, long axis length and inclination angle. The axis ratio follows a right half-normal distribution. Using Monte Carlo method, the location and shape parameters of the spheroids are randomly selected. The particle volume fraction is calculated using the area ratio of the spheroids. Then, the effects of particle/matrix interface and strengthening mechanism on the distribution of Mises stress and equivalent strain and the flow behaviour for the composites are discussed.     

Effect of particle size of graphites on electrical conductivity of graphite/polymer composite

The effect of particle size of graphite particles on the dispersion state of graphite particles and electrical conductivity of graphite/low-density polyethylene (LDPE) composites is investigated. Graphite particles which have plate-like and spherical shapes and mean particle sizes of 2.1 to 82.6 μm are used. Scanning electron microscopy observation showed that graphite particles are not aggregated and ordered along the direction of mixing-roll in the polymer matrix. X-ray diffraction measurements show that crystallite size of the (110) plane of polyethylene crystal and the crystallinity are significantly affected by the particle size of graphite particles. These results were interpreted as due to the orientation of PE crystallites. The electrical conductivity of composites changes discontinuously at the critical volume fraction of particles, Ø_c. The Ø_c values given by the percolation equation increase with decreasing of the particle size of graphites. The plate-like graphite particles with a mean particle size of 2.1 μm could induce conductivity at Ø_c of 0.135. The values of Ø_c increased linearly with increasing of the mean particle sizes of the plate-like graphites. The value of Ø_c of spherical graphite particle is the largest value, 0.292, in all specimens.     

Influence of demagnetizing field on the permeability of soft magnetic composites

The influence of demagnetizing field on the effective permeability of magnetic composites has been investigated. A theoretical expression of the effective permeability has been obtained and discussed according to four typical composites with spheres, needles, flakes, and aligned prolate ellipsoidal particles. The results indicate that the demagnetizing field within the particles can reduce the effective permeability significantly. In order to increase the effective permeability, it is necessary to decrease the demagnetizing field within the particles. A linear relationship between effective permeability and volume fraction is also observed for composites filled with spherical particles at low volume fraction.     

Distance or Spacing Parameters in Agglomerated Monosized Spherical Particulate Systems

The mean nearest distance between separated neighboring particles is one of the most important microstructural parameter for two phases or multiphase materials, such as hard particle re-inforced metal matrix composites. It influences most of the mechanical, thermal, and electrical properties of such materials. This is the first theoretical model that highlights the effects of the volume fraction of particles, mean particle size, and contiguity on the average nearest distance between separated neighboring particles.     

磁致伸缩/压电层叠复合材料磁电效应分析

采用有限元分析软件COMSOL5.0建立了三维悬臂梁模型,分析了磁致伸缩/压电/磁致伸缩叠层复合材料的磁电系数α_(ME),并就几何参数对复合结构磁电系数的影响进行了优化分析.首先,利用稳态求解器研究了磁电层状复合结构内部的应力、应变、位移以及电势分布情况,利用瞬态求解分析了磁电复合结构各变量动态分布规律;其次,应用小信号频域分析研究了该结构的谐振频率以及在不同偏置磁场对输出电压的影响,结果表明,随着直流偏置磁场的增加,输出电压逐渐减小.改变复合材料不同层的厚度,分析了磁电层与压电层厚度比t_m/t_p对磁电系数的影响,结果表明,随着厚度比增加,α_(ME)逐渐增大,其增加速率逐渐减小;最后,分析了磁电系数α_(ME)随复合结构面积、长宽比的变化情况.分析表明,α_(ME)随磁电复合结构面积的增加逐渐增加,其增加速率逐渐减小;当磁电复合结构面积恒定时,其磁电系数随长宽比L/W增加表现出先增加后减小的趋势,存在最优值.     

Analysis of ultrasonic attenuation in particle-reinforced plastics by a differential scheme

Attenuation of ultrasonic longitudinal waves in some particle-reinforced polymer composites is studied theoretically by a micromechanical model based on a differential (incremental) scheme. A set of differential equations is established by which the attenuation spectrum of the composite can be computed from the known properties of viscoelastic matrix and elastic particles. For a composite reinforced with glass particles with radius 0.15 mm, the proposed scheme is shown to predict the attenuation in better agreement with the foregoing experimental results than the previous simplistic independent scattering model. Based on this scheme, the dependence of the longitudinal attenuation spectrum of a particulate polymer composite on the wavelength-to-particle radius ratio and the particle volume fraction is examined in detail. It is then shown theoretically that the attenuation of the composite decreases monotonically with the particle volume fraction when the particle radius is sufficiently small compared to the incident wavelength, while it shows non-monotonic particle-fraction dependence when the ratio of the particle radius to the wavelength is larger. To examine this theoretical finding from an experimental point of view, the longitudinal attenuation in a glass-particle-reinforced polyester composite with particle radius 0.0225 mm is measured for different particle volume fractions. The measured attenuation characteristics are shown to support the qualitative features of the theoretical prediction.     

A model for predicting magnetic targeting of multifunctional particles in the microvasculature

A mathematical model is presented for predicting magnetic targeting of multifunctional carrier particles that are designed to deliver therapeutic agents to malignant tissue in vivo. These particles consist of a nonmagnetic core material that contains embedded magnetic nanoparticles and therapeutic agents such as photodynamic sensitizers. For in vivo therapy, the particles are injected into the vascular system upstream from malignant tissue, and captured at the tumor using an applied magnetic field. The applied field couples to the magnetic nanoparticles inside the carrier particle and produces a force that attracts the particle to the tumor. In noninvasive therapy, the applied field is produced by a permanent magnet positioned outside the body. In this paper, a mathematical model is developed for predicting noninvasive magnetic targeting of therapeutic carrier particles in the microvasculature. The model takes into account the dominant magnetic and fluidic forces on the particles and leads to an analytical expression for predicting their trajectory. An analytical expression is also derived for predicting the volume fraction of embedded magnetic nanoparticles required to ensure capture of the carrier particle at the tumor. The model enables rapid parametric analysis of magnetic targeting as a function of key variables including the size of the carrier particle, the properties and volume fraction of the embedded magnetic nanoparticles, the properties of the magnet, the microvessel, the hematocrit of the blood and its flow rate.     

Analysis of ultrasonic attenuation in particle-reinforced plastics by a differential scheme

Attenuation of ultrasonic longitudinal waves in some particle-reinforced polymer composites is studied theoretically by a micromechanical model based on a differential (incremental) scheme. A set of differential equations is established by which the attenuation spectrum of the composite can be computed from the known properties of viscoelastic matrix and elastic particles. For a composite reinforced with glass particles with radius 0.15 mm, the proposed scheme is shown to predict the attenuation in better agreement with the foregoing experimental results than the previous simplistic independent scattering model. Based on this scheme, the dependence of the longitudinal attenuation spectrum of a particulate polymer composite on the wavelength-to-particle radius ratio and the particle volume fraction is examined in detail. It is then shown theoretically that the attenuation of the composite decreases monotonically with the particle volume fraction when the particle radius is sufficiently small compared to the incident wavelength, while it shows non-monotonic particle-fraction dependence when the ratio of the particle radius to the wavelength is larger. To examine this theoretical finding from an experimental point of view, the longitudinal attenuation in a glass-particle-reinforced polyester composite with particle radius 0.0225 mm is measured for different particle volume fractions. The measured attenuation characteristics are shown to support the qualitative features of the theoretical prediction.     

Depolarization regions of nonzero volume in bianisotropic homogenized composites

In conventional approaches to the homogenization of random particulate composites, the component phase particles are often treated mathematically as vanishingly small, point-like entities. The electromagnetic responses of these component phase particles are provided by depolarization dyadics which derive from the singularity of the corresponding dyadic Green functions. Through neglecting the spatial extent of the depolarization region, important information may be lost, particularly relating to coherent scattering losses. We present an extension to the strong-property-fluctuation theory in which depolarization regions of nonzero volume and ellipsoidal geometry are accommodated. Therein, the size, shape and spatial distribution of the component phase particles are taken into account. The analysis is developed within the most general linear setting of bianisotropic homogenized composite mediums (HCMs). Numerical results are presented for a representative example of a bianisotropic HCM, namely a Faraday chiral medium. These studies reveal that estimates of the HCM constitutive parameters in relation to volume fraction, particle eccentricity, particle orientation and correlation length are all significantly influenced by the size of the component phase particles.     

偏置磁场对磁致伸缩/弹性/压电层合材料磁电效应的影响

根据磁致伸缩材料的非线性本构关系得到其动态杨氏弹性模量和动态压磁系数,结合等效电路法得到磁致伸缩/弹性/压电层合材料的磁电效应与磁致伸缩材料的动态杨氏弹性模量和动态压磁系数的关系,讨论了偏置磁场对这种层合材料的谐振频率和谐振磁电电压转换系数的影响.理论推导和实验结果均表明,存在最佳偏置磁场使磁致伸缩/弹性/压电层合材料的谐振磁电电压转换系数最大. 关键词： 磁致伸缩/弹性/压电层合材料 磁电效应 偏置磁场 非线性本构关系     

Depolarization regions of nonzero volume in bianisotropic homogenized composites

In conventional approaches to the homogenization of random particulate composites, the component phase particles are often treated mathematically as vanishingly small, point-like entities. The electromagnetic responses of these component phase particles are provided by depolarization dyadics which derive from the singularity of the corresponding dyadic Green functions. Through neglecting the spatial extent of the depolarization region, important information may be lost, particularly relating to coherent scattering losses. We present an extension to the strong-property-fluctuation theory in which depolarization regions of nonzero volume and ellipsoidal geometry are accommodated. Therein, the size, shape and spatial distribution of the component phase particles are taken into account. The analysis is developed within the most general linear setting of bianisotropic homogenized composite mediums (HCMs). Numerical results are presented for a representative example of a bianisotropic HCM, namely a Faraday chiral medium. These studies reveal that estimates of the HCM constitutive parameters in relation to volume fraction, particle eccentricity, particle orientation and correlation length are all significantly influenced by the size of the component phase particles.     

用于电流传感的声表面波磁致伸缩效应

利用声表面波(SAW)磁致伸缩效应可以实现一种快速、高灵敏度的电流检测方法,但磁致伸缩薄膜内部矫顽力导致了明显的磁滞误差。磁致伸缩薄膜的栅阵化设计可以减小磁致伸缩时薄膜内部矫顽力,抑制磁滞现象,从而实现高灵敏和低迟滞误差的SAW电流检测。结合有限元和耦合模理论对沉积铁钴(FeCo)薄膜栅阵的声表面波电流传感器中的磁致伸缩效应进行分析,对传感响应进行仿真,确定优化的传感结构参数。为验证理论分析,实验研制了频率为150 MHz的声表面波电流传感器件,并结合差分振荡电路及亥姆霍兹线圈,建立传感器测试系统.实验结果表明,磁致伸缩薄膜的栅阵设计大幅降低了迟滞误差,并显著提升了传感器灵敏度。      

Nanoparticle composites: FePt with wide-band-gap semiconductor

We present a simple way to synthesize FePt and ZnO (wide-band-gap semiconductor) nanoparticle composites. The FePt nanoparticles were fabricated using the method reported by Sun et al. By controlling the heating rate, 3 nm FePt nanoparticles were synthesized. Well-dispersed FePt and ZnO nanoparticle composites were prepared by further adding zinc acetate and oleyl amine into the 3 nm FePt nanoparticle dispersion. By controlling the molar ratio of the FePt and zinc acetate, FePt and ZnO nanoparticle composites with different FePt particle fractions were obtained. The intensity of photo luminescence spectra of the nanoparticle composites increases very much with decreasing FePt particle fraction, whereas the peak position shifts a little. After annealing at 550 °C for half an hour, the nanoparticle composites become magnetically hard or semi-hard with coercivity much dependent on the FePt particle volume fraction. The coercivity of the composites increases with annealing temperature. The composites hold the promise of applications in new generation recording and/or optical devices.     

磁致伸缩/压电叠层复合材料磁-机-电耦合系数分析

分析和推导了磁致伸缩/压电叠层复合材料的机-电耦合系数、磁-机耦合系数及磁-电耦合系数与磁致伸缩层和压电层性能参数及几何参数之间的关系.进一步分析表明,叠层复合材料低频时的磁电电压系数正比于磁-电耦合系数,谐振时的磁电电压系数正比于磁-电耦合系数与机械品质因素的乘积;磁电电压系数还与复合结构的本征阻抗有关,本征阻抗越大磁电电压系数越大.通过性能差异较大的Terfenol-D和FeNi基弹性合金分别与压电材料PZT5-H和PZT8相互组合构成复合材料的比较分析,进一步阐明了磁电复合材料磁-电耦合系数和机械品 关键词： 磁电效应 磁-机-电耦合系数 磁致伸缩材料 压电材料