Simultaneous determination of 2-nitrophenol and 4-nitrophenol based on the multi-wall carbon nanotubes Nafion-modified electrode

In this work, multi-wall carbon nanotubes (MWNT) were conveniently dispersed into Nafion-ethanol solution, and the MWNT-Nafion-modified glassy carbon electrode (GCE) was described for the simultaneous determination of 2-nitrophenol and 4-nitrophenol. At pH 4.0 phosphate buffer, the reduction peak currents of 2-nitrophenol (at -0.8 V) and 4-nitrophenol (at -1.0 V) increase significantly at the MWNT-Nafion-modified GCE, in comparison with that at the Nafion-modified GCE and the bare GCE. The experimental parameters, such as solution pH of phosphate buffer, accumulation potential and time, and the amounts of MWNT-Nafion onto the GCE surface, were optimized. The reduction peak currents are linear with the concentration of 2-nitrophenol from 5 x 10(-8) to 1 x 10(-5) mol L(-1) and with that of 4-nitrophenol from 1 x 10(-7) to 1 x 10(-5) mol L(-1). The detection limits after 3-min accumulation are 1 x 10(-8) mol L(-1) for 2-nitrophenol and for 4 x 10(-8) mol L(-1) for 4-nitrophenol. This modified electrode was applied to direct determination of 2-nitrophenol and 4-nitrophenol in lake water samples.     

Voltammetric determination of terbinafine in biological fluid at glassy carbon electrode modified by cysteic acid/carbon nanotubes composite film

The electrochemical oxidation of L-cysteine (CySH) in presence of carbon nanotubes (CNTs) formed a composite film at a glassy carbon electrode (GCE) as a novel modifier for directly electroanalytical determination of terbinafine without sample pretreatment in biological fluid. The determination of terbinafine at the modified electrode with strongly accumulation was studied by differential pulse voltammetry (DPV). The peak current obtained at +1.156 V (vs. SCE) from DPV was linearly dependent on the terbinafine concentration in the range of 8.0 x 10(-8)-5.0 x 10(-5 )M in a B-R buffer solution (0.04 M, pH 1.81) with a correlation coefficient of 0.998. The detection limit (S/N=3) was 2.5 x 10(-8 )M. The low-cost modified electrode showed good sensitivity, selectivity, and stability. This developed method had been applied to the direct determination of terbinafine in human serum samples with satisfactory results. It is hopeful that the modified electrode will be applied for the medically clinical test and the pharmacokinetics in future.     

Electrochemical determination of nitrite using a gold nanoparticles-modified glassy carbon electrode prepared by the seed-mediated growth technique.

Seed-mediated growth of gold nanoparticles on glassy carbon (GC) surfaces was developed. The field emission scanning electron microscopy (FE-SEM) and electrochemical characterization confirmed the effective attachment of gold nanoparticles on GC surface with such a wet-chemical method. The as-prepared gold nanoparticles attached glassy carbon electrode (Au/GCE) presented excellent catalytic ability toward the oxidation of nitrite. Compared with bare GCE and planar gold electrode, the Au/GCE obviously decreased the overpotential of nitrite oxidation and improved the peak current. The catalytic current was found to be linearly proportional to the nitrite concentration in the range of 1 x 10(-5) - 5 x 10(-3) M, with a detection limit of 2.4 x 10(-6) M. The Au/GCE was successfully applied to the electrochemical determination of nitrite in a real wastewater sample, showing excellent stability and anti-interference ability.     

Poly(amidosulfonic acid) modified glassy carbon electrode for determination of isoniazid in pharmaceuticals

Amidosulfonic acid was electropolymerized by cyclic voltammetry onto the surface of glassy carbon electrode (GCE) to fabricate the chemically modified electrode, which showed high stability, good selectivity and reproducibility for determination of isoniazid. The modified electrode showed an excellent electrocatalytical effect on the oxidation of isoniazid. Under the optimum conditions, there was a good linear relationship between anodic peak current and isoniazid concentration in the range of 5.0 x 10(-8)- 1.0 x 10(-5) M, and a detection limit of 1.0 x 10(-8) M (S/N = 3) was obtained after 120 s at the accumulation potential of - 0.2 V (vs. SCE). This developed method had been applied to the direct determination of isoniazid in injection and tablet samples with satisfactory results.     

Voltammetric determination of sinomenine in biological fluid using a glassy carbon electrode modified by a composite film of polycysteic acid and carbon nanotubes

Polycysteic acid based electrochemical oxidation of L-cysteine (CySH) and carbon nanotubes (CNTs) formed a composite thin film material at a glassy carbon electrode (GCE) that was used a novel modifier for electroanalytical determination of sinomenine which is used for rheumatoid arthritis treatment. The determination of sinomenine at the composite modified electrode was studied by differential pulse voltammetry (DPV). The peak current obtained at + 0.632 V (vs SCE) from DPV was linearly dependent on the sinomenine concentration in the range of 1.0 x 10(-7) to 6.0 x 10(-5) M in a B-R buffer solution (0.04 M, pH 1.81) with a correlation coefficient of 0.998. The detection limit (S/N = 3) was 5.0 x 10(-8) M. The electrochemical reaction mechanism of sinomenine was also discussed. This new method was then applied to the high-throughput determination of sinomenine in human serum samples with satisfactory results. This polycysteic acid/CNTs composite film may be considered to be a promising, low-cost, durable, and biocompatible material for the modification of sensors in applications to pharmaceutical and biomedical analysis.     

A poly(3-acetylthiophene) modified glassy carbon electrode for selective voltammetric measurement of uric acid in urine sample

A reliable and reproducible method for the determination of uric acid in urine samples has been developed. The method is based on the modification of a glassy carbon electrode by 3-acetylthiophene using cyclic voltammetry. The poly(3-acetylthiophene) modified glassy carbon electrode showed an excellent electrocatalytic effect towards the oxidation of uric acid in 0.1 m phosphate buffer solution (PBS) at pH 7.2. Compared with a bare glassy carbon electrode (GCE), an obvious shift of the oxidation peak potential in the cathodic direction and a marked enhancement of the anodic current response for uric acid were observed. The poly(3-acetylthiophene)/GCE was used for the determination of uric acid using square wave voltammetry. The peak current increased linearly with the concentration of uric acid in the range of 1.25 x 10(-5)-1.75 x 10(-4) M. The detection limit was 5.27 x 10(-7) M by square wave voltammetry. The poly(3-acetylthiophene)/GCE was also effective to determine uric acid and ascorbic acid in a mixture and resolved the overlapping anodic peaks of these two species into two well-defined voltammetric peaks in cyclic voltammetry at 0.030 V and 0.320 V (vs. Ag/AgCl) for ascorbic acid and uric acid, respectively. The modified electrode exhibited stable and sensitive current responses toward uric acid and ascorbic acid. The method has successfully been applied for determination of uric acid in urine samples.     

Determination of trace levels of diosmin in a pharmaceutical preparation by adsorptive stripping voltammetry at a glassy carbon electrode.

A systematic study on the electrochemical behavior of diosmin in Britton-Robinson buffer (pH 2.0-10.0) at a glassy carbon electrode (GCE) was made. The oxidation process of the drug was found to be quasi-reversible with an adsorption-controlled step. The adsorption stripping response was evaluated with respect to various experimental conditions, such as the pH of the supporting electrolyte, the accumulation potential and the accumulation time. The observed anodic peak current at +0.73 V vs. Ag/AgCl reference electrode increased linearly over two orders of magnitude from 5.0x10(-8) M to 9.0x10(-6) M. A limit of detection down to 3.5x10(-8) M of diosmin at the GCE was achieved with a mean recovery of 97+/-2.1%. Based on the electrochemical data, an open-circuit accumulation step in a stirred sample solution of BR at pH 3.0 was developed. The proposed method was successfully applied to the determination of the drug in pharmaceutical formulations. The results compared favorably with the data obtained via spectrophotometric and HPLC methods.     

Voltammetry of the interaction of metronidazole with DNA and its analytical applications

Voltammetric methods were used to probe the interaction of antimicrobial drug metronidazole (MTZ) with calf thymus DNA. Binding constants (K) and binding site sizes (s) were determined from the voltammetric data, i.e., shifts in potential and changes in limiting current with the addition of DNA. MTZ showed appreciable electrostatic binding to DNA in solution with K=2.2(+/- 1.3) x 10(4) M(-1) and s=0.34 bp. One reduction peak of MTZ at the bare glassy carbon electrode (GCE) split into two peaks at the DNA modified GCE (DNA/GCE). These changes in the cyclic voltammogram can only be due to the interaction of MTZ with the surface-confined DNA. In addition, the peak current of MTZ at the DNA/GCE was nearly 8-fold of the response at the bare GCE. The low detection limit of 2.0 x 10(-8) M made the DNA/GCE a promising biosensor for MTZ determination. And this method was successfully applied with high precision and accuracy compared with spectroscopic methods (relative error < 6%) for estimation of the total MTZ drug content in pharmaceutical dosage forms.     

Studies of the interaction between Aloe-emodin and DNA and preparation of DNA biosensor for detection of PML-RARalpha fusion gene in acute promyelocytic leukemia

The interaction of Aloe-emodin (AE) with salmon sperm DNA in 0.1M Tris-HCl buffer (pH 4.4) and at the DNA-modified glassy carbon electrode (GCE) was systemically studied with voltammetry and ultraviolet-visible (UV-vis) spectroscopy. AE had excellent electrochemical activity on the GCE with a couple of redox peaks. We propose that AE can intercalate into DNA strands forming a nonelectroactive complex, which results in the decrease of the reduction peak current of AE. The Langmuir adsorption constants of AE at ss- and dsDNA/GCE were (2.1+/-0.4)x10(5) and (2.7+/-0.2)x10(5)M(-1), respectively. The difference between AE at ss- and dsDNA has been used for the preparation of a sequence-specific DNA electrochemical biosensor for detection of PML-RARalpha fusion gene in acute promyelocytic leukemia (APL) with a detection limit of 6.7x10(-8)M and a linear range from 1.5x10(-8) to 1.5x10(-7)M. The selectivity of ssDNA-modified electrode was also described.     

Electrochemistry and voltammetric determination of colchicine using an acetylene black-dihexadecyl hydrogen phosphate composite film modified glassy carbon electrode

The electrochemical behavior of colchicine at an acetylene black-dihexadecyl hydrogen phosphate (denoted as AB-DHP) composite film coated glassy carbon electrode (GCE) was investigated using cyclic voltammetry (CV), linear sweep voltammetry (LSV) and differential pulse voltammetry (DPV). Compared with the poor electrochemical signal at the unmodified GCE, the electrochemical response of colchicine at the AB-DHP film modified GCE was greatly improved, as confirmed from the significant peak current enhancement. The remarkable peak current enhancement indicates that the AB-DHP modified GCE has great potential in the sensitive determination of colchicine. Thus, all the experimental conditions, which influence the electrochemical response of colchicine, were studied and the optimum conditions were achieved. Finally, a sensitive and simple voltammetric method with a good linear relationship in the range of 1.0 x 10(-7) approximately 4.0 x 10(-5) mol/L, was developed for the determination of colchicine. The detection limit of colchicine was also examined and a low value of 4.0 x 10(-8) mol/L for 4-min accumulation was obtained (S/N=3). This electrode was successfully applied to detect colchicine in human urine samples.     

Electro-oxidation and determination of antihistamine drug, cetirizine dihydrochloride at glassy carbon electrode modified with multi-walled carbon nanotubes

A multi-walled carbon nanotube (MWCNT) film-modified glassy carbon electrode (GCE) was constructed for the determination of an antihistamine drug, cetirizine dihydrochloride (CTZH) using cyclic voltammetry (CV). Owing to the unique structure and extraordinary properties of MWCNT, the MWCNT film has shown an obvious electrocatalytic activity towards oxidation of CTZH, since it facilitates the electron transfer and significantly enhances the oxidation peak current of CTZH. All experimental parameters have been optimized. Under the optimum conditions, the oxidation peak current was linearly proportional to the concentration of CTZH in the range from 5.0×10(-7) to 1.0×10(-5)M. The detection limit was 7.07×10(-8)M with 180s accumulation. Finally, the proposed sensitive and simple electrochemical method was successfully applied to CTZH determination in pharmaceutical and urine samples.     

Covalent modification of glassy carbon electrodes with glycine for voltammetric separation of dopamine and ascorbic acid

Glycine was covalently grafted on to a glassy carbon electrode (GCE) by amine cation radical formation in electrooxidation of the amino-containing compound. X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry proved the immobilization of glycine on the GCE. The modified electrode reduced the overpotentials of dopamine (DA) and ascorbic acid (AA) by approximately 0.15 V and 0.23 V, respectively, and resolved the overlapping voltammetric response of DA and AA into two well-defined voltammetric peaks in cyclic voltammetry (CV) or differential pulse voltammetry (DPV), unlike the unmodified GCE; this can be used for the simultaneous determination of these species in a mixture. The differential pulse peak current was linearly dependent on DA and AA concentration in the range 5 x 10(-6)-8 x 10(-4) mol L(-1) and 6 x 10(-5)-4 x 10(-3) mol L(-1), with correlation coefficients of 0.996 and 0.994, respectively. The detection limits (3delta) for DA and AA were 1.8 x 10(-6) mol L(-1) and 2.1 x 10(-5) mol L(-1), respectively. The modified electrode is very sensitive, selective and stable, and has been applied to the determination of DA and AA simultaneously in samples with satisfactory results.     

Electrochemistry and voltammetry of procaine using a carbon nanotube film coated electrode

A new rapid, convenient and sensitive electrochemical method is described for the determination of procaine in pharmaceutical preparations, based on the unique properties of a multi-wall carbon nanotube (MWNT) thin film. The electrochemical behavior of procaine at the MWNT film-coated glassy carbon electrode (GCE) was investigated in detail, showing that the MWNT-coated GCE exhibits electrocatalytic activity to the oxidation of procaine because of the significant peak current enhancement and the lowering of oxidation overpotential. Furthermore, the mechanism for the oxidation of procaine at the MWNT-coated GCE was also studied. Finally, various experimental parameters such as solution pH value, the amount of MWNT, accumulation conditions and scan rate were optimized for the determination of procaine, and a new method with detection limit of 2 x 10(-7) mol/L was developed for procaine determination. This newly proposed method was successfully demonstrated with procaine hydrochloride injection.     

Electrochemical oxidation of luteolin at a glassy carbon electrode and its application in pharmaceutical analysis

Luteolin is a flavonoid reported to occur widely in many medicinal plants. The electrochemical behavior of luteolin was studied in phosphate buffer solution (PBS) of pH 4.0 at a glassy carbon electrode (GCE) by cyclic voltammetry (CV) and differential pulse voltammetric method (DPV). The results indicated the well-defined redox peak of luteolin which was involving two electrons and two protons was observed and the electrode process is adsorption-controlled. The charge transfer coefficient (alpha) was calculated as 0.66. The relationships between oxidation peak current and the concentration of luteolin are linear in the range of 1.0 x 10(-8) - 1.0 x 10(-6) M by DPV method. The detection limit had been estimated as 5.0 x 10(-9) M. The facile and rapid method has been successfully applied to the detection of luteolin in tablets.     

Sensitive voltammetric assay of etoposide using modified glassy carbon electrode with a dispersion of multi-walled carbon nanotube

A sensitive electroanalytical method for the determination of anticancer drug etoposide (ETP) using adsorptive stripping differential pulse voltammetry (AdSDPV) at a multi-walled carbon nanotube-modified glassy carbon electrode (MWCNT-modified GCE) is presented. The surface morphology of modified electrode was characterized by scanning electron microscopy. The effects of accumulation time and potential, pH, scan rate, and amount of MWCNT suspension were investigated. The calibration curve was linear in the concentration range of 2.0?×?10^?8–2.0?×?10^?6 M with the detection limit of 5.4?×?10^?9 M. The reproducibility of the peak current was found at 1.55 % (n?=?5) RSD value in pH 6.0 Britton–Robinson buffer for the MWCNT-modified GCE. The method was then successfully utilized for the determination of ETP in pharmaceutical dosage form, and a recovery of 99.55 % was obtained. The possible oxidation mechanism of ETP was also discussed. The proposed electroanalytical method using MWCNT-modified GCE is the most sensitive method for the determination of ETP with lowest limit of detection in the previously published electrochemical methods.     

Voltammetric determination of niclosamide at a glassy carbon electrode

A very sensitive and selective procedure was developed for the determination of niclosamide based on square-wave voltammetry at a glassy carbon electrode. Cyclic voltammetry was used to investigate the electrochemical reduction of niclosamide at a glassy carbon electrode. Niclosamide was first irreversibly reduced from NO2 to NHOH at -0.659 V in aqueous buffer solution of pH 8.5. Reversible and well defined peaks at -0.164 V and -0.195 V (vs. Ag/AgCl) were obtained that are responsible for two electron peaks between NHOH and NO. Following optimisation of the voltammetric parameters, pH and reproducibility, a linear calibration curve over the range 5 x 10(-8)-1 x 10(-6) mol dm(-3) was achieved. The detection limit was found to be 2.05 x 10(-8) mol dm(-3) niclosamide. For eight successive determinations of 5 x 10(-7) mol dm(-3) niclosamide, a relative standard deviation of 2.4% was obtained. This voltammetric method was applied to the direct determination of niclosamide in tablets. The results of the analysis suggest that the proposed method has promise for the routine determination of niclosamide in the products examined.     

阿奇霉素在多壁碳纳米管修饰电极上的电化学行为及其测定

运用循环伏安法与线性扫描伏安法研究了阿奇霉素在多壁碳纳米管修饰玻碳电极上的电化学行为,建立了一种直接测定阿奇霉素的电化学分析方法。结果表明,与裸玻碳电极相比,多壁碳纳米管修饰电极能显著提高阿奇霉素的氧化峰电流,阿奇霉素的电极过程完全不可逆,存在典型的吸附特性。在优化的实验条件下,氧化峰电流与阿奇霉素浓度在3.0×10-7～2.5×10-5 mol/L和2.5×10-5～5.0×10-4 mol/L范围内呈现良好的线性关系,检出限为1.0×10-7 mol/L。     

Sensitive detection of trifluoperazine using a poly-ABSA/SWNTs film-modified glassy carbon electrode

A poly-ABSA/SWNTs composite-modified electrode was fabricated by electropolymerizing aminobenzene sulphonic acid (ABSA) on the surface of glassy carbon electrode (GCE) modified with single-wall carbon nanotubes (SWNTs). SWNTs provide a 3D porous and conductive network for the polymer immobilization. The nanocomposite film was characterized by scanning electron microscope (SEM) and electrochemical impedance spectroscopy (EIS). The results indicated that this composite-modified electrode had strong electrocatalytic activity toward the oxidation of trifluoperazine (TFP). TFP could effectively accumulate on the modified electrode and generate a sensitive anodic peak at 0.72V (versus SCE) in pH 6.1 phosphate buffer solution. Under the selected conditions, the anodic peak current of TFP was linear with its concentration within the range from 1.0x10(-7) to 1.0x10(-5)molL(-1) and 1.0x10(-5) to 1.0x10(-4)molL(-1), and the detection limit was 1.0x10(-9)molL(-1) (S/N=3). This method was successfully applied to the detection of trifluoperazine in drug samples and the recovery was satisfactory. In comparison with the SWNTs/GCE or poly-ABSA/GCE prepared in the similar way, this composite-modified electrode exhibited better catalytic activity.     

Electrochemical behavior and voltammetric determination of norfloxacin at glassy carbon electrode modified with multi walled carbon nanotubes/Nafion

A simple and rapid electrochemical method is developed for the determination of trace-level norfloxacin, based on the excellent properties of multi-walled carbon nanotubes (MWCNTs). The MWCNTs/Nafion film-coated glassy carbon electrode (GCE) is constructed and the electrochemical behavior of norfloxacin at the electrode is investigated in detail. The results indicate that MWCNTs modified glassy carbon electrode exhibited efficiently electrocatalytic oxidation for norfloxacin (NFX) with relatively high sensitivity, stability and life time. Under conditions of cyclic voltammetry, the current for oxidation of selected analyte is enhanced significantly in comparison to the bare GCE. The electrocatalytic behavior is further exploited as a sensitive detection scheme for the analyte determinations by linear sweep voltammetry (LSV). Under optimized condition in voltammetric method the concentration calibration range and detection limit (S/N=3) are 0.1-100 micromol/L and 5 x 10(-8)mol/L for NFX. The proposed method was successfully applied to NFX determination in tablets. The analytical performance of this sensor has been evaluated for detection of the analyte in urine as a real sample.     

Electrochemical reduction and voltammetric determination of metronidazole at a nanomaterial thin film coated glassy carbon electrode

Simple and sensitive electrochemical method for the determination of metronidazole, based on a nanostructured film coated glassy carbon electrode (GCE), is described. Multi-walled carbon nanotubes (MWNT) was dispersed into water in the presence of a hydrophobic surfactant to give very stable and homogeneous MWNT suspension, and a MWNT-film coated GCE was achieved via evaporating solvent. Metronidazole yields a well-defined reduction peak whose potential is −0.71 V at the MWNT-film coated GCE in pH 9.0 Britton-Robinson buffer. Compared with bare GCE, the MWNT-film modified GCE significantly enhances the reduction peak current of metronidazole. All the experimental parameters were optimized for the determination of metronidazole. The detection limit is 6×10⁻⁹ mol/l at 2 min accumulation. This method has been successfully used to determine metronidazole in the drugs. Furthermore, results obtained by the proposed method have been compared with spectrophotometric method.