Polyelectrolyte complexes. VII. Complex nanoparticles based on poly(sodium 2‐acrylamido‐2‐methylpropanesulfonate) tailored by the titrant addition rate

Nonstoichiometric interpolyelectrolyte complexes (IPECs) as colloidal dispersions have been widely used for the past decade as reactive materials for flocculation and surface modification. In this context, some new aspects of the preparation and properties of IPEC nanoparticles based on NaPAMPS, in salt‐free aqueous solutions, are reported in this article. IPEC dispersions with different characteristics, z‐averaged particle sizes, polydispersity indices, and colloidal stabilities were tailored by the addition rate of the titrant, a less investigated factor in the synthesis of IPECs as nanoparticles. Poly(sodium 2‐acrylamido‐2‐methylpropanesulfonate) (NaPAMPS) and two polycations bearing positive charges in the backbone, poly(diallyldimethylammonium chloride) and a polycation containing 95 mol % N,N‐dimethyl‐2‐hydroxypropyleneammonium chloride units, were used for this purpose. The complex nanoparticle characteristics and storage stability were monitored via the optical density at 500 nm and dynamic light scattering. IPEC nanoparticles with z‐averaged particle sizes of 100–250 nm resulted from the same polyion pair and the same polyion concentrations when the addition rate of the titrant, either the polyanion or polycation, varied within the range of 0.1–1.5 mL/mL of the starting polyion × h. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5244–5252, 2004     

Nonstoichiometric interpolyelectrolyte complexes as colloidal dispersions based on NaPAMPS and their interaction with colloidal silica particles

Preparation and characterization of some nonstoichiometric interpolyelectrolyte complexes (NIPECs) as stable colloidal dispersions by the interaction between poly(sodium 2-acrylamido-2-methylpropanesulfonate) (NaPAMPS) and three strong polycations bearing quaternary ammonium salt centres in the backbone, poly(diallyldimethylammonium chloride) (PDADMAC) and two polycations containing N,N-dimethyl-2-hydroxypropyleneammonium chloride units (PCA₅ and PCA₅D₁), have been followed in this study as a function of the polycation structure and polyelectrolyte concentration. Complex characteristics were followed by polyelectrolyte titration, turbidity and quasi-ellastic light scattering. Almost monodisperse NIPECs nanoparticles with a good storage stability were prepared when total concentration of polyelectrolyte was varied in the range 0.85-6.35 mmol/L, at a ratio between charges (n⁻/n⁺) of 0.7. NIPECs as a new kind of flocculants were used to flocculate a stable monodisperse silica suspension. The main advantage of NIPECs as flocculants is the broad flocculation window, which is a very important aspect for industrial applications.     

Polyelectrolyte complexes. II. Specific aspects of the formation of polycation/dye/polyanion complexes

We report on the formation of the polycation/dye/polyanion (PC/D/PA) complexes by the interaction between nonstoichiometric polycation/dye (PC/D) complexes with polyanions. Polycations differed in their content of the (N,N‐dimethyl‐2‐hydroxypropylene ammonium chloride) units in the main chain. Poly(sodium acrylate) (NaPA), poly(sodium 2‐acrylamido‐2‐methylpropane sulfonate) (NaPAMPS) and poly(sodium styrenesulfonate) (NaPSS) were used as polyanions. Crystal Ponceau 6R (CP6R) and Ponceau 4R (P4R) with two or three sulfonic groups were used as anionic dyes. The interaction between nonstoichiometric PC/D complexes and polyanions was followed by UV‐VIS spectroscopy, viscometry, and conductometry measurements. Formation of PC/D/PA complexes takes place mainly by the electrostatic interaction between the polyanion and the free positive charges of the nonstoichiometric PC/D complex. The stoichiometry and the stability of the tricomponent complexes depended on the polycation structure, the structure and molecular weight of polyanion, the dye structure, and the P/D molar ratio. A high amount of the dye was excluded from the complex before the end point when a branched polycation was used. The higher the solubility of the dye the lower the stability of the PC/D/PA complexes. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 409–418, 1999     

Polyelectrolyte complexes. V. Solid‐state properties of some polycation/azo dye complexes controlled by the dye structure

The solid‐state properties of some polycation/azo dye complexes according to the dye structure were studied in this work. One polycation contained about 95 mol % N,N‐dimethyl‐2‐hydroxypropyleneammonium chloride units in the backbone (PCA₅), and eight azo dyes, different in either the number of sulfonic groups or their distribution, were used as opposite components. The selected azo dyes were as Crystal Scarlet, Congo Red, Crocein Scarlet MOO, Ponceau SS, Amaranth, Ponceau S, Direct Blue 1, and Direct Red 80. Information on the compensation degree of the oppositely charges was obtained by the elemental analysis of the solid‐state polycation/dye complexes (the experimental contents of chlorine, nitrogen, and sulfur were compared with the calculated values). Differential scanning calorimetry was employed to probe the strength of the intermolecular interactions in the PCA₅/dye complexes. Wide‐angle X‐ray diffraction was used to assess the supramolecular order of the solid‐state complexes. The physical properties of the PCA₅/azo dye complexes (the complex stoichiometry, glass‐transition temperature, decomposition temperature, and degree of supramolecular order) were influenced mainly by the dye structure but also by the polycation concentration and the presence of NaCl. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 264–272, 2003     

A photochromic dinuclear compound: aquatetrakis(μ‐2,3‐diphenylprop‐2‐enoato)bis(2,3‐diphenylprop‐2‐enoato)ethanolbis(1,10‐phenanthroline)dilanthanum(III)

The title dinuclear complex, (aqua‐1κO)tetrakis(μ‐2,3‐diphenylprop‐2‐enoato‐1:2κ²O:O′)bis(2,3‐diphenylprop‐2‐enoato)‐1κO;2κO‐(ethanol‐2κO)bis(1,10‐phenanthroline)‐1κ²N,N′;2κ²N,N′‐dilanthanum(III), [La₂(C₁₅H₁₁O₂)₆(C₁₂H₈N₂)₂(C₂H₅OH)(H₂O)], contains two similar La^III centres with distorted [LaO₆N₂] bicapped triganol–prismatic coordination polyhedra formed by six phenylcinnamate (PCA⁻ or 2,3‐diphenylprop‐2‐enoate) ligands, two 1,10‐phenanthroline (phen) ligands, a coordinating ethanol molecule and a coordinating water molecule. The two metal centres are bridged by four μ‐PCA⁻ ligands, with the remaining two PCA⁻ ligands coordinated in a monodentate fashion. The noncoordinated carboxylate O atoms on the terminal PCA⁻ ligands form O—H...O hydrogen bonds with the coordinated solvent molecules. Each La centre is also coordinated by a bidentate phen ligand. The PCA⁻ ligands all adopt syn–syn orientations, with the two phenyl rings presenting dihedral angles of about 70°. The compound displays photochromic behaviour both in solution and in the solid state.     

Synthesis of double‐hydrophilic block copolymers via combination of oxyanion‐initiated polymerization and polymer reaction for fabricating magnetic target gene carrier

In this work, we have synthesized a polycation and a polyanion via a combination of oxyanion‐initiated polymerization and polymer reaction, and then developed a novel approach to prepare a controlled magnetic target gene carrier with magnetic Fe₃O₄ nanoparticles as core and poly(ethylene glycol) (PEG) segment as corona via layer‐by‐layer (LbL) assembly and shell‐crosslinking. Magnetic nanoparticles (MNPs) were first modified by poly[2‐(dimethylamino)ethyl methacrylate] (PDMAEMA) via radical polymerization. The resulting MNPs were used to compact deoxyribonucleic acid (DNA) through LbL assembly, involving four steps: ( 1 ) the binding of DNA to the polycation PDMAEMA on the surface of MNPs; ( 2 ) the produced particles in Step 1 with negative charge interacting with additional polycation ethoxy group end‐capped PDMAEMA (EtO‐PDMAEMA) homopolymer, leading to a positive charge surface; ( 3 ) using carboxyl group (‐COO^‐) of poly(methacrylic acid) (PMAA) in a diblock copolymer (MePEG2000‐b‐PMAA_SH) as polyanion, which has partial mercapto groups (‐SH) in PMAA segment, to interact with the particles produced in Step 2; ( 4 ) the shell of the composite nanoparticle was crosslinked by oxidizing the ‐SH groups of the MePEG2000‐b‐PMAA_SH to form disulfide linkage (S? S). All the processes of LbL assembly were investigated by agarose gel retardation assay and zeta potential measurements. The in vitro cytotoxicity analysis proves that polyions/DNA MNPs have excellent properties and potential applications as gene carriers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A Novel Synthesis of 2-Amino-2-deoxy-D-gluconic Acid and Its Complexation with Cu（Ⅱ） in Alkaline Medium

A novel synthesis of the functional carbohydrate 2-amino-2-deoxy-D-gluconic acid was introduced and itscomplex formation with Cu(Ⅱ)was investigated to obtain the stability constant for its further applications to thefood and pharmaceutical industries.The equilibrium was investigated by spectrophotometric measurements andprocessed by dual-series linear regression method.Results:the yield of 2-amino-2-deoxy-D-gluconic acid is 70%.The complexation molar ratio is 1:2,the molar apsorptivity of the complex is 39.906 L·mol~(-1)·cm~(-1) at 630 nm,and the stability constant β_n is 6.24×10~5.     

Polyion Detection via All‐solid‐contact Paper‐based Polyion‐sensitive Polymeric Membrane Electrodes

The first all‐solid‐contact paper‐based single‐use polyion‐sensitive ion‐selective electrodes (ISEs) are described. These polyion‐sensitive ISEs are fabricated using cellulose filter paper coated with a carbon ink conductive layer. A polyanion sensing membrane is cast on a section of the coated paper and the sensor is insulated, resulting in a disposable, single‐use device. Various polyanions are shown to yield large negative potentiometric responses when using these disposable devices for direct polyanion detection. These new sensors are further demonstrated to be useful in indirect polycation detection when polycations (i. e., polyquaterniums (PQs)) are titrated with polyanionic dextran sulfate (DS). Titrations monitored using these paper‐based, all‐solid‐contact devices yield endpoints proportional to the given PQ concentration present in the test sample.     

Conformational changes of strong polycations in the presence of divalent counterions and their influence upon the flocculation efficiency

The interaction between strong polycations, which possess the ammonium quaternary centers attached to an acrylic macromolecular chain derived from poly(N,N-dimethylaminoethyl methacrylate) (polycations Q_x), and divalent counterions was investigated by viscometry and turbidimetry. Conformational changes of polycations were influenced by the polycation charge density, counterion nature (SO₄²⁻ or S₂O₈²⁻) and concentration. The morphology of the polycation layers deposited onto silicon wafers has been studied by tapping mode atomic force microscopy, a strong influence of the polycation and ammonium persulfate concentration on the surface topography being observed. The optimum flocculation concentration of polycation decreased and the flocculation window increased in the presence of S₂O₈²⁻, in the destabilization of kaolin model dispersion. Removal of Congo Red from aqueous solution by the complex system formed between polycations and divalent counterions was also investigated. The behavior of polycations Q_x in separation processes was compared with that of one polycation containing 95 mol% N,N-dimethyl-2-hydroxypropyleneammonium chloride units in the backbone (PCA₅).     

Synthesis and characterization of di‐n‐butyltin(IV) complexes with 4′/2′‐nitrobiphenyl‐2‐carboxylic acids: X‐ray crystal structures of [{(n‐C4H9)2Sn(OCOC12H8NO2−4′)}2O]2 and (n‐C4H9)2Sn{OCOC12H8NO2−4′}2

Reactions of di‐n‐butyltin(IV) oxide with 4′/2′‐nitrobiphenyl‐2‐carboxylic acids in 1 : 1 and 1 : 2 stoichiometry yield complexes [{(n‐C₄H₉)₂Sn(OCOC₁₂H₈NO₂?4′/2′)}₂O]₂ ( 1 and 2 ) and (n‐C₄H₉)₂Sn(OCOC₁₂H₈NO₂?4′/2′)₂ ( 3 and 4 ) respectively. These compounds were characterized by elemental analysis, IR and NMR (¹H, ¹³C and ¹¹⁹Sn) spectroscopy. The IR spectra of these compounds indicate the presence of anisobidentate carboxylate groups and non‐linear C? Sn? C bonds. From the chemical shifts δ (¹¹⁹Sn) and the coupling constants ¹J(¹³C, ¹¹⁹Sn), the coordination number of the tin atom and the geometry of its coordination sphere have been suggested. [{(n‐C₄H₉)₂Sn(OCOC₁₂H₈NO₂?4′)}₂O]₂ ( 1 ) exhibits a dimeric structure containing distannoxane units with two types of tin atom with essentially identical geometry. To a first approximation, the tin atoms appear to be pentacoordinated with distorted trigonal bipyramidal geometry. However, each type of tin atom is further subjected to a sixth weaker interaction and may be described as having a capped trigonal bipyramidal structure. The diffraction study of the complex (n‐C₄H₉)₂Sn(OCOC₁₂H₈NO₂?4′)₂ ( 3 ) shows a six–coordinate tin in a distorted octahedral frame containing bidentate asymmetric chelating carboxylate groups, with the n‐Bu groups trans to each other. The n‐Bu? Sn? n‐Bu angle is 152.8° and the Sn? O distances are 2.108(4) and 2.493(5) Å. The oxygen atom of the nitro group of the ligand does not participate in bonding to the tin atom in 1 and 3 . Crystals of 1 are triclinic with space group P1 and of that of 3 have orthorhombic space group Pnna. Copyright © 2003 John Wiley & Sons, Ltd.     

PAN composite membrane with different solvent affinities controlled by surface modification methods

Polyacrylonitrile (PAN) composite membranes with surface properties designed by either a chemical modification with ethylenediamine (EDA), or layer‐by‐layer (LbL) polyelectrolyte adsorption were investigated in this paper. Fourier‐transformed infrared (FTIR) spectroscopy and streaming potential measurements showed that the first step of the reaction with EDA in gas phase was the formation of ammonium salts with the reactive carboxylic groups present on the surface of the starting membrane. Part of the ammonium carboxylate groups was transformed in secondary amide linkages by a heat‐induced reaction. Poly(sodium styrenesulfonate) (NaPSS) and a polycation containing about 95 mol % of N,N‐dimethyl‐2‐hydroxypropyleneammonium chloride units in the backbone (PCA₅) were used as opposite polyions in the LbL film construction. The adsorbed polyion amount per every layer was controlled by the nature and concentration of the supporting electrolyte in polyelectrolyte deposition solution (NaBr and KBr). An almost linear increase of the adsorbed polyion amount versus the layer pair number was observed. The swelling degree (SD) in pure alcohols of the LbL‐modified PAN composite membrane decreased with the increase of the solvent polarity and with the decrease of the pore volume by pore filling with polyelectrolyte complex multilayer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4161–4171, 2005     

Synthesis of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline)‐block‐poly(ε‐caprolactone) copolymers

A series of novel types of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline)‐block‐poly(ε‐caprolactone) (PHpr‐b‐PCL) copolymers were successfully synthesized via melt block copolymerization of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) and ε‐caprolactone (ε‐CL) with a trifunctional initiator trimethylolpropane (TMP) and stannous octoate (SnOct₂) as a catalyst. For the homopolycondensation of N‐CBz‐Hpr with TMP initiator and SnOct₂ catalyst, the number‐average molecular weight (M_n) of prepolymer increases from 530 to 3540 g mol^?1 with the molar ratio of monomer to initiator (3–30), and the molecular weight distribution (M_w/M_n) is between 1.25 to 1.32. These three‐armed prepolymer PHpr were subsequently block copolymerized with ε‐caprolactone (ε‐CL) in the presence of SnOct₂ as a catalyst. The M_n of the copolymer increased from 2240 to 18,840 g mol^?1 with the molar ratio (0–60) of ε‐CL to PHpr. These products were characterized by differential scanning calorimetry (DSC), ¹H NMR, and gel permeation chromatography. According to DSC, the glass‐transition temperature (T_g) of the three‐armed polymers depended on the molar ratio of monomer/initiator that were added. In vitro degradation of these copolymers was evaluated from weight‐loss measurements and the change of M_n and M_w/M_n. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1708–1717, 2005     

Amperometric Hydrogen Peroxide Biosensor Based on the Immobilization of Horseradish Peroxidase (HRP) on the Layer‐by‐Layer Assembly Films of Gold Colloidal Nanoparticles and Toluidine Blue

The precursor film was first formed on the Au electrode surface based on the self‐assembly of L ‐cysteine and the adsorption of gold colloidal nanoparticles (nano‐Au). Layer‐by‐layer (LBL) assembly films of toluidine blue (TB) and nano‐Au were fabricated by alternately immersing the electrode with precursor film into the solution of toluidine blue and gold colloid. Cyclic voltammetry (CV) and quartz crystal microbalance (QCM) were adopted to monitor the regular growth of {TB/Au} bilayer films. The successful assembly of {TB/Au}_n films brings a new strategy for electrochemical devices to construct layer‐by‐layer assembly films of nanomaterials and low molecular weight materials. In this article, {TB/Au}_n films were used as model films to fabricate a mediated H₂O₂ biosensor based on horseradish peroxidase, which responded rapidly to H₂O₂ in the linear range from 1.5×10^?7 mol/L to 8.6×10^?3 mol/L with a detection limit of 7.0×10^?8 mol/L. Morphologies of the final assembly films were characterized with scanning probe microscopy (SPM).     

Ring‐opening polymerization of β‐butyrolactone catalyzed by efficient magnesium and zinc complexes derived from tridentate anilido‐aldimine ligand

Magnesium (Mg) and zinc (Zn) complexes incorporating tridentate anilido‐aldimine ligand, (E)‐2, 6‐diisopropyl‐N‐(2‐((2‐(piperidin‐1‐yl)ethylimino)methyl)phenyl)aniline ( AA ^Pip ‐H, 1 ), were synthesized and structurally characterized. The reaction of AA ^Pip ‐H ( 1 ) with MgⁿBu₂ or ZnEt₂ in equivalent proportions afforded the monomeric complex [( AA ^Pip )MgⁿBu] ( 2 ) or [( AA ^Pip )ZnEt] ( 3 ), respectively. The coordination modes of these complexes differ in the solid state: Mg complex 2 shows a four‐coordinated and distorted tetrahedral geometry, whereas Zn complex 3 adopts a trigonal planar geometry with a three‐coordinated Zn center. Complexes 2 and 3 are efficient catalysts for the ring‐opening polymerization of β‐butyrolactone (β‐BL) in the presence of 9‐anthracenemethanol (9‐AnOH). The polymerization of β‐BL with the Zn catalyst system is demonstrated in a living fashion with a narrow polydispersity index, PDI = 1.01–1.10. The number‐averaged molecular weight (M_n) of the produced poly(3‐hydroxybutyrate) (PHB) is quite close to the expected M_n over diverse molar ratios of monomer to 9‐AnOH. A greater ratio of monomer to alcohol catalyzed by Zn complex 3 served to form PHB with a large molecular weight (M_n > 60000). An effective method to prepare PHB‐b‐PCL and PEG‐b‐PHB by the ring‐opening copolymerization of β‐BL catalyzed by zinc complex 3 is reported. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Regiodirected Synthesis and Stereochemistry of 2,4,8‐Trialkyl‐3‐thia‐1,5‐diazabicyclo[3.2.1]octanes and α,ω‐Bis(2,4,6‐trialkyl‐1,3,5‐dithiazinane‐5‐yl)alkanes

2,4,8‐Trialkyl‐3‐thia‐1,5‐diazabicyclo[3.2.1]octanes have been obtained by the regioselective and stereoselective cyclocondensation of 1,2‐ethanediamine with aldehydes RCHO (R═Me, Et, Prⁿ, Buⁿ, Pentⁿ) and H₂S at molar ratio 1:3:2 at 0°C. The increase in molar ratio of thiomethylation mixture RCHO–H₂S (6:4) at 40°C resulted in selective formation of bis‐(2,4,6‐trialkyl‐1,3,5‐dithiazinane‐5‐yl)ethanes. Cyclothiomethylation of aliphatic α,ω‐diamines with aldehydes RCHO (R═Me, Et) and H₂S at molar ratio 1:6:4 and at 40°С led to α,ω‐bis(2,4,6‐trialkyl‐1,3,5‐dithiazinane‐5‐yl)alkanes. Stereochemistry of 2,4,8‐trialkyl‐3‐thia‐1,5‐diazabicyclo[3.2.1]octanes have been determined by means of ¹H and ¹³С NMR spectroscopy and further supported by DFT calculations at the B3LYP/6‐31G(d,p) level. The structure of α,ω‐bis(2,4,6‐trialkyl‐1,3,5‐dithiazinane‐5‐yl)alkanes was confirmed by single‐crystal X‐ray diffraction study.     

Titanium complexes based on aminodiol ligands for the ring‐opening polymerization of ε‐caprolactone,rac‐β‐butyrolactone,and trimethylene carbonate

Several titanium complexes based on aminodiol ligands were tested as initiators for the ring‐opening polymerization (ROP) of ε‐caprolactone under solution and bulk conditions. All complexes were found to be efficient under both conditions. For bulk polymerization at 70 °C, high activities were observed (113.3–156.2 g_poly mmol_cat^?1 h^?1) together with controlled molar mass distribution. Kinetic studies revealed controlled polymerization, and the chain propagation was first order with respect to monomer conversion. One complex was also tested for the ROP of rac‐β‐butyrolactone and the end‐group analysis suggested that ring opening occurs through acyl‐oxygen bond cleavage via coordination–insertion mechanism. The microstructure analysis of polymer by ¹³C NMR indicates atactic polymer. Another complex was also found to be efficient initiator for the ROP of trimethylene carbonate under solution and bulk conditions. Again, end‐group analysis suggests coordination–insertion mechanism. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Nanoparticles based on polyelectrolyte complexes: effect of structure and net charge on the sorption capability for solved organic molecules

 The sorption of solved organic molecules such as p-nitrophenol or dyes on previously formed nanoparticles based on polyelectrolyte/micelle complexes or polycation/polyanion complexes was studied. It could be shown that the sorption capability strongly depends on the structure and properties of the complex particles. Investigations have been made with complex particles that differ in their hydrophobic/hydrophilic structure, size and net charge. Such complex aggregates could be prepared by mixing the cationic surfactant dodecylamido-ethyldimethylbenzylammonium chloride, the polycations poly(diallyldimethylammonium chloride) or poly(methacryloyloxyethyldimethylbenzylammonium chloride) and the copolymers of maleic acid with propene or methylstyrene as anionic components. It is found that the sorption capability increases with increasing molar mass and hydrophobic properties of the components used. In addition, the concentration ratio c _polym/c _org.poll that was required to reach optimal sorption conditions could be decreased by the use of macromolecules with high molar masses. The best results were obtained by using cationic stabilized complex particles formed with high-molar-mass polycations as sorbents for anionic dye molecules. Received: 10 November 1999 Accepted: 24 February 2000     

Functional syndiotactic poly(β‐hydroxyalkanoate)s via stereoselective ring‐opening copolymerization of rac‐β‐butyrolactone and rac‐allyl‐β‐butyrolactone

The copolymerization of racemic β‐butyrolactone (rac‐BL^Me) with racemic “allyl‐β‐butyrolactone” (rac‐BL^allyl) in toluene, catalyzed by the discrete amino‐alkoxy‐bis(phenolate) yttrium‐amido complex 1 , gave new poly(β‐hydroxyalkanoate)s with unsaturated side chains. The poly(BL^Me‐co‐BL^allyl) copolymers produced have a highly syndiotactic backbone structure (P_r = 0.80–0.84) with a random enchainment of monomer units, as evidenced by ¹³C NMR, and high molecular weight (M_n up to 58,000 g mol^?1) with a narrow polydispersity (M_w/M_n = 1.07–1.37), as determined by GPC. The comonomer incorporation (5–50 mol % rac‐BL^allyl) was a linear function of the feed ratio. The pendant vinyl bond of the side‐chains in those poly(BL^Me‐co‐BL^allyl) copolymers allowed the effective introduction of hydroxy or epoxy groups via dihydroxylation, hydroboration‐oxidation or epoxidation reactions. NMR studies indicated that all of these transformations proceed in an essentially quantitative conversion and do not affect the macromolecular architecture. Some thermal properties (T_m, ΔH_m, T_g) of the prepared polymers have been also evaluated. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3177–3189, 2009     

OH‐Initiated Photooxidations of 1‐Pentene and 2‐Methyl‐2‐propen‐1‐ol: Mechanism and Yields of the Primary Carbonyl Products

The products of the gas‐phase reactions of OH radicals with 1‐pentene and 2‐methyl‐2‐propen‐1‐ol (221MPO) at T=298±2 K and atmospheric pressure were investigated by using a 4500 L atmospheric simulation chamber that was built especially for this work. The molar yield of butyraldehyde was 0.74±0.12 mol for the reaction of 1‐pentene. This work provides the first product molar yield determination of formaldehyde (0.82±0.12 mol), 1‐hydroxypropan‐2‐one (0.84±0.13 mol), and methacrolein (0.078±0.012 mol) from the reaction of 221MPO with OH radicals. The mechanism of this reaction is discussed in relation to the experimental results. Additionally, taking into consideration the complex mechanism, the rate coefficients of the reactions of OH with formaldehyde, 1‐hydroxypropan‐2‐one, and methacrolein were derived at atmospheric pressure and T=298±2 K.; the obtained values were (8.9±1.6)×10^?12, (2.4±1.4)×10^?12, and (22.9±2.3)×10^?12 cm³ molecule^?1 s^?1, respectively.     

Visible light‐induced thiol‐ene reaction: A new strategy to prepare Α,ω‐dithiol and Α,ω‐divinyl telechelic polythiolether oligomers

A new strategy is developed to prepare both α,ω‐dithiol and α,ω‐divinyl linear telechelic polythiolether oligomers by visible light induced thiol‐ene chemistry in the presence of a fac‐Ir(ppy)₃ photoredox catalyst. Polythiolether oligomers of well‐defined end groups and controlled molecular weights have been successfully synthesized at varying monomer molar ratios of 1,4‐benzenedimethanethiol (BDMT) to diethylene glycol divinyl ether (DEGVE). ¹H NMR and MALDI‐TOF MS analyses demonstrate that as‐prepared polythiolethers possess high end‐group fidelity, which is further supported by the successful polyaddition of polythiolethers bearing α,ω‐dithiol and α,ω‐divinyl groups. For example, with the α,ω‐dithiol‐ (M_n = 1900 g mol^?1, PDI = 1.25) and α,ω‐divinyl‐terminated (M_n = 2000 g mol^?1, PDI = 1.29) polythiolethers as macromonomers, the molecular weight of resulting polythiolether is up to 7700 g mol^?1 with PDI as 1.67. The reactivity of the terminal thiol group is further confirmed by the addition reaction with N‐(1‐pyrenyl)maleimide. UV‐vis spectra and fluorescene measurements suggest that fac‐Ir(ppy)₃ undergo a redox quenching process reacted with BDMT to generate thiyl free radicals. With these results, the mechanism of the thiol‐ene reaction catalyzed by photoredox catalyst is proposed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 740–749