Magnesium chloride supported high mileage catalysts for olefin polymerization. XII. Polymerization of ethylene

Polymerizations of ethylene by the MgCl₂/ethylbenzoate/p-cresol/AlEt₃ TiCl₄-AlEt₃/methyl-p-toluate (CW-catalyst) have been studied. The initially formed active site concentration, [Ti] has a maximum value of 50% of total titanium at 50°C and lower values at other temperatures. The Ti decays rapidly to Ti sites with conc. ca. 10 mol %/mol Ti. The rate constants for four chain transfer processes have been obtained at 50°C: for transfer with AlEt₃, k = 2.1 × 10^?4 s^?1 and k = 4.8 × 10^?4 s^?1; for transfer with monomer, k = 3.6 × 10^?3 (M s)^?1 and K = 8.3 × 10^?3 (M s)^?1; for β-hydride transfer, k = 7.2 × 10^?4 s^?1 and k = 4.9 × 10^?4 s^?1; and transfer with hydrogen, k = 4.0 × 10^?3 torr^1/2 s^? and k = 5.1 × 10^?3 torr^1/2 s^?1. The rate constants for the termination assisted by hydrogen is k = 1.7 (M^1/2 torr^1/2 S)^?1. If monomer is assisting termination as was observed for propylene polymerization, then k = 7.8 (M^3/2 s)^?1. Values of all the rate constants can be higher or lower at other temperatures. Detailed comparisons were made with the results of propylene polymerizations. There are more than four times as many Ti active sites for ethylene polymerization than there are for stereospecific polymerization of propylene; the difference is more than a factor of two for the Ti sites. Certain rate constants are nearly the same for both monomers while others are markedly different. Some of the differences can be explained by stereoelectronic effects.     

Kinetics of crosslinking reactions. 2. Reaction rates of intermolecular and intramolecular crosslinkings by using a soluble microgel

Soluble microgels with several pendant vinyl groups were synthesised by radical copolymerization of methyl methacrylate (MMA) with p-divinyl benzene (p-DVB). The competitive reactions of intermolecular and intramolecular crosslinkings of these microgels were carried out at 40°C in the presence of 1-buten-3-ol as a degradative chain transfer agent. The rate constant of intermolecular crosslinking (k) was estimated by GPC (gel permeation chromatography) analysis on the polymer produced from intermolecular propagation between bimolecules. The k depended strongly on the internal structure of microgels. Network formation was discussd inclusive of informations for the rate constant of intramolecular crosslinking (k).     

Primary radical termination and unimolecular termination in the heterogeneous polymerization of acrylamide initiated by a fluorinated azo‐derivative initiator: A kinetic study

Acrylamide was polymerized in acetonitrile at 82 °C with a perfluorinated azo‐derivative initiator. The polymerization proceeded heterogeneously. Varying amounts of initiator and monomer were used. The activation energy was deduced from three experiments carried out at 59, 71, and 82 °C. The following kinetic law, deviating a great deal from the classical law, was obtained: R ∼ [I₂][M](0.05% < [I₂]_o/[M]_o < 1.00%) and R ∼ [I₂][M](1% < [I₂]_o/[M]_o < 7%). These results can be interpreted in light of the contribution of primary radical termination and the emergence of occlusion. The development of a new kinetic relationship allowed us to confirm the existence of both of these termination reactions. The calculation of the k_prt /k_i · k_p ratio was also achieved. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1834–1843, 2000     

Reactivities of carbocations and monomers in carbocationic polymerization and copolymerization

In carbocationic polymerization and copolymerization, a recent publication concluded that the substituent effect on carbocation reactivity is much larger than its effect on monomer reactivity, and this by a factor 10⁶ in the case of the rate constant k_12capp for p‐methylstyrene addition (monomer M₂) on, respectively, poly(p‐methoxystyrene)^± or poly(p‐methylstyrene)^± (M). This conclusion is disputed, as well as the assumption that the rate constants of capping (k_12capp) obtained in deactivation reactions of poly(p‐methoxystyrene)^± are identical with cross propagation rate constants in copolymerization (k_12copol). It is shown that the large calculated k_12capp are based on propagation constant values for p‐methylstyrene (k ≈ 10⁹) obtained by the diffusion‐clock method. They are 10⁴ times smaller as found for all styrenes, that is, between 10⁴ and 10⁵ when they are based on the ionic species concentrations. In such a case, the available data are still in agreement with an approximate compensation between the reactivities of a monomer and of the corresponding carbocation. It is also shown that copolymerization data for styrenes are not compatible with k values near to diffusion control, and that variations of log k_12capp and log k_12copol with the nucleophilicity parameter N of the monomers indicate a much lower selectivity of the monomers in the case of copolymerization. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2666–2680, 2010     

Binding of uranyl ion by poly(ethylenimine) containing a salicylate derivative

Three molecules of 5-(bromoacetyl)salicylate ( 1 ) complexed to uranyl UO ion were crosslinked with branchy poly(ethylenimine) (PEI) in DMSO by alkylation of amino groups of PEI with 1, leading to the formation of UO₂(Sal) PEI. Upon demetalation of UO₂(Sal) PEI with HCl, apo(Sal) PEI was obtained. Based on the pH dependence of log K_f for UO₂(Sal) PEI, it was concluded that each uranyl binding site in UO₂(Sal) PEI or apo(Sal) PEI contains three salicylate moieties. In terms of the equilibrium constant for formation of the uranyl complex, apo(Sal) PEI was found to be comparable to or better than the previously reported effective uranophiles. In terms of the rates for the formation of the uranyl complex, however, apo(Sal) PEI was far superior to those other uranophiles. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2935–2942, 1997     

Cationic grafting from carbon black. VIII. Cationic ring-opening polymerization and copolymerization of oxepane initiated by acylium perchlorate groups on carbon black

The cationic ring-opening polymerization of oxepane was found to be initiated by carbon black having acylium perchlorate (CO⁺CIO) groups, which were introduced by the reaction of acyl chloride groups with silver perchlorate. It was confirmed that polyoxepane, i.e., poly(oxyhexamethylene), was propagated from CO⁺CIO groups on carbon black and effectively grafted on the surface. The rate of the polymerization and the percentage of grafting of poly(oxyhexamethylene) remarkably increased by the addition of epichlorohydrin (ECH) as a promoter: the percentage of grafting in the presence of ECH increased to about 100% with an increase in conversion. Furthermore, CO⁺CIO groups on carbon black have an ability to initiate the cationic ring-opening copolymerization of oxepane with ECH to give poly(oxepane-co-ECH) with various composition. The ring-opening copolymerization of oxepane with phthalic anhydride was also initiated by CO⁺CIO groups to give polyether ester, i.e., poly(hexamethylene phthalate) containing poly(oxyhexamethylene) sequence. In the copolymerization, polyether or polyether ester was effectively grafted from carbon black based on the propagation of these polymers from CO⁺CIO groups.     

Magnesium chloride supported high mileage catalysts for olefin polymerization. XIII. Effect of external Lewis base on ethylene polymerization

The effect of external Lewis base (B_e) on the polymerization of ethylene by the MgCl₂/ethyl benzoate/p-cresol/AlEt₃/TiCl₄ catalyst was studied by activation with AlEt₃ alone without the use of methyl-p-toluate. The initially formed active site concentration, [Ti], is about doubled in the absence of B_e; at 50°C about 93% of the total titanium became catalytic. The same increment of [Ti] was observed without B_e. The rate constants of propagation are not appreciably affected by B_e; the values are the same at 50° with and without B_e. At other temperatures the k_p values are somewhat smaller without B_e. One major effect was the very large k values for chain transfer with aluminum alkyls in the absence of B_e as compared to those with B_e. This can be attributed to the greater monomeric AlEt₃ concentration in the former, but in much smaller amounts in the presence of B_e due to complexation. The rate constants of chain transfer with hydrogen are not much affected by B_e. However, the termination rate constants are generally much smaller when Lewis base is not present.     

Synthesis and characterizations of well‐defined branched polymers with AB2 branches by combination of RAFT polymerization and ROP as well as ATRP

A well‐defined branched copolymer with PLLA‐b‐PS₂ branches was prepared by combination of reversible addition‐fragmentation transfer (RAFT) polymerization, ring‐opening polymerization (ROP), and atom transfer radical polymerization (ATRP). The RAFT copolymerization of methyl acrylate (MA) and hydroxyethyl acrylate (HEA) yielded poly(MA‐co‐HEA), which was used as macro initiator in the successive ROP polymerization of LLA. After divergent reaction of poly(MA‐co‐HEA)‐g‐PLLAOH with divergent agent, the macro initiator, poly(MA‐co‐HEA)‐g‐PLLABr₂ was formed in high conversion. The following ATRP of styrene (St) produced the target polymer, poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). The structures, molecular weight, and molecular weight distribution of the intermediates and the target polymers obtained from every step were confirmed by their ¹H NMR and GPC measurements. DSC results show one T = 3 °C for the poly(MA‐co‐HEA), T = ?5 °C, T= 122 °C, and T = 157 °C for the branched copolymers (poly(MA‐co‐HEA)‐g‐PLLA), and T = 51 °C, T = 116 °C, and T = 162 °C for poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 549–560, 2006     

Role of anions in the polymerization of 2,5‐dimethoxyaniline in the presence of poly(styrene sulfonic acid)

Poly(2,5‐dimethoxyaniline) (PDMA)–Ag composites were successfully obtained through the oxidative polymerization of 2,5‐dimethoxyaniline in poly(styrene sulfonic acid) with CH₃SO₃Ag and AgNO₃ as oxidants. In situ ultraviolet–visible spectroscopy results showed that the growth rate of PDMA was strongly affected by CH₃SO and NO. The coupling reaction of PDMA and NO was proposed to explain the lower growth rate of PDMA with AgNO₃ as the oxidant in comparison with CH₃SO₃Ag. X‐ray photoelectron spectroscopy and Fourier transform infrared spectroscopy were used to validate the proposed coupling reaction through the monitoring of the side products and oxidized state of PDMA. The results showed that there were more side products and lower oxidized states for the composite structure in the presence of NO than in the presence of CH₃SO, and this agreed with the proposal. Transmission electron microscopy showed that the Ag nanoparticles had almost the same size, regardless of the anions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6624–6632, 2006     

Solvay type VCl3 isospecific catalysts

Solvay type S –VCl₃ catalyst has 7% of catalytically active vanadium sites ([C^*]) with k_p (rate constant of propagation) = 31 (M s)^?1 for ethylene polymerization. Addition of a comonomer, propylene of 4-methylpentene-1 (4-MP) significantly raised the ethylene polymerization activity. S –VCI₃ catalyst has very small amounts of catalytically active vanadium for propylene polymerizations: [C] = 0.19% with k_p,i = 857 (M s)^?1 and [C] = 0.45% with k_p,a = 23 (M s)^?1 for isospecific and nonspecific sites, respectively. Addition of a conomer, ethylene or 4-MP. lowered the propylene polymerization activity. S –VCI₃ is more easily reduced to the divalent ion by AIR₃ than S –TiCl₃. Methyl-p-toluate moderates the reducting power of AIR₃; it increase the productivity and stereoselectivity of the S –YiCl₃ catalyst, VCI₃ supported on MgCl₂ (CW–V catalyst) has enhanced rate constant of propylene polymerization but has the opposite effects on the S –TiCl₃ Catalyst. VCI₃ supported on MgCl₂ (CW–V catalyst) has enhances rate constant of propylene polymerization but only a minute fraction of the supported vanadiums are catalytically active: [C] = 0.019% and k_p,i = 1580 (Ms)^?1, [C] = 0.057% and k_p,i = 58 (M s)^?1. This is compared with far greater number of catalytically active titanium sites in the TiCl₃ supported on MgCl₂ catalyst: [C] = 6% and k_p,i = 200 (M s)^?1, [C] = 6% and k_p,a = 16(M s)^?1. Therefore, both the S –VCI₃ and CW–V catalysts are highly stereoselective but low in efficiency with respect to the utilization of the vanadium ion in the catalysis.     

Depolymerization kinetics of di(4‐tert‐butyl cyclohexyl) itaconate and Mark‐Houwink‐Kuhn‐Sakurada parameters of di(4‐tert‐butyl cyclohexyl) itaconate and di‐n‐butyl itaconate

Multipulse pulsed laser polymerization coupled with size exclusion chromatography (MP‐PLP‐SEC) has been employed to study the depropagation kinetics of the sterically demanding 1,1‐disubstituted monomer di(4‐tert‐butylcyclohexyl) itaconate (DBCHI). The effective rate coefficient of propagation, k, was determined for a solution of monomer in anisole at concentrations, c, 0.72 and 0.88 mol L^?1 in the temperature range 0 ≤ T ≤ 70 °C. The resulting Arrhenius plot (i.e., ln k vs. 1/RT) displayed a subtle curvature in the higher temperature regime and was analyzed in the linear part to yield the activation parameters of the forward reaction. In the temperature region where no depropagation was observed (0 ≤ T ≤ 50 °C), the following Arrhenius parameters for k_p were obtained (DBCHI, E_p = 35.5 ± 1.2 kJ mol^?1, ln A_p = 14.8 ± 0.5 L mol^?1 s^?1). In addition, the k data was analyzed in the depropagatation regime for DBCHI, resulting in estimates for the associated entropy (?ΔS = 150 J mol^?1 K^?1) of polymerization. With decreasing monomer concentration and increasing temperature, it is increasingly more difficult to obtain well structured molecular weight distributions. The Mark Houwink Kuhn Sakurada (MHKS) parameters for di‐n‐butyl itaconate (DBI) and DBCHI were determined using a triple detection GPC system incorporating online viscometry and multi‐angle laser light scattering in THF at 40 °C. The MHKS for poly‐DBI and poly‐DBCHI in the molecular weight range 35–256 kDa and 36.5–250 kDa, respectively, were determined to be K_DBI = 24.9 (10³ mL g^?1), α_DBI = 0.58, K_DBCHI = 12.8 (10³ mL g^?1), and α_DBCHI = 0.63. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1931–1943, 2007     

A chiral polymer‐based turn‐on fluorescent sensor for specific recognition of hydrogen sulfate

A new kind of polymeric chemosensor containing chiral naphthaldimine moiety in the side chain was synthesized by the reversible addition‐fragmentation chain transfer polymerization of N‐{[2‐(4‐vinylbenzyloxy)‐1‐naphthyl]‐methylene}‐(S)‐2‐phenylglycinol (VNP). The resulting polymers (PVNP) showed high selectivity for hydrogen sulfate relative to other anions including F^?, Cl^?, Br^?, H₂PO, CH₃CO, and NO in tetrahydrofuran (THF) solution as judged from UV?vis, fluorescence, and circular dichroism spectrophotometric titrations. Compared with its monomer, the polymer has proven to be more attractive for detection of HSO in terms of sensitivity and reproducibility. Upon addition of the anion it gives remarkable spectral responses concomitant with detectable color change from colorless to pale yellow. Furthermore, the HSO‐induced CD or fluorescence signal can be totally reversed with addition of base and eventually recovered the initial state, leading to a reproducible molecular switch with two distinguished “on” and “off” states. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Visible light induced free radical promoted cationic polymerization using thioxanthone derivatives

The free radical promoted cationic polymerization cyclohexene oxide (CHO), was achieved by visible light irradiation (λ_inc = 430–490 nm) of methylene chloride solutions containing thioxanthone‐fluorene carboxylic acid (TX‐FLCOOH) or thioxanthone‐carbazole (TX‐C) and cationic salts, such as diphenyliodonium hexafluorophosphate (Ph₂I⁺PF) or silver hexafluorophosphate (Ag⁺PF) in the presence of hydrogen donors. A feasible initiation mechanism involves the photogeneration of ketyl radicals by hydrogen abstraction in the first step. Subsequent oxidation of ketyl radicals by the oxidizing salts yields Bronsted acids capable of initiating the polymerization of CHO. In agreement with the proposed mechanism, the polymerization was completely inhibited by 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy and di‐2,6‐di‐tert‐butylpyridine as radical and acid scavengers, respectively. Additionally polymerization efficiency was directly related to the reduction potential of the cationic salts, that is, Ag⁺PF (E = +0.8 V) was found to be more efficient than Ph₂I⁺PF (E = ?0.2 V). In addition to CHO, vinyl monomers such as isobutyl vinyl ether and N‐vinyl carbazole, and a bisepoxide such as 3,4‐epoxycyclohexyl‐3′,4′‐epoxycyclohexene carboxylate, were polymerized in the presence of TX‐FLCOOH or TX‐C and iodonium salt with high efficiency. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Anionic polymerization of N-substituted maleimide. V. A study on the kinetic features of anionic polymerization of N-phenylmaleimide

The kinetic feature of the anionic polymerization of N-PMI was investigated in THF. The polymerization system initiated with lithium tert-butoxide was revealed to be so-called “slow-initiation” system. The rate constant of the initiation reaction, k_i, was obtained to be 4.2 × 10^?3 (L mol^?1 s^?1) at ?72°C. The apparent rate constants of the propagation reaction, k, at ?72°C were individually obtained from each slope of the first-order plots in the later stages of the polymerizations for four different initiator concentrations. Each k is fairly close to that of initiation rate around 10^?3. The propagation reaction was concluded to be dominated by ion-pair mechanism from the analysis of the kinetic data and the results of the addition effects of crown ether and common salt.     

Chain-length dependent termination in pulsed-laser polymerization, 5. The evaluation of the rate coefficient of bimolecular termination kt for the reference system styrene in bulk at 25°C

Following earlier suggestions the values for the rate coefficient of chain termination k_t in the bulk polymerization of styrene at 25°C were formally calculated (a) from the second moment of the chainlength distribution (CLD) and (b) from the rate equation for laser-initiated pseudostationary polymerization (both expressions originally derived for chain-length independent termination) by inserting the appropriate experimental data including the rate constant of chain propagation k_p. These values were treated as average values, k and k , respectively. They exhibited good mutual agreement, even the predicted gradation (k < k by about 20%) was recovered. The log-log plot of k_t vs. the number-average degree of polymerization of the chains at the moment of their termination yielded exponents b of 0.16–0.18 in the power-law k_t = A · P_n ^−b, A ranging from 2.3 × 10⁸ to 2.7 × 10⁸ L · mol⁻¹ · s⁻¹. These data are only slightly affected if termination is not assumed to occur by recombination only and a small contribution of disproportionation is allowed for.     

Electrochemical synthesis of PEDOT derivatives bearing imidazolium‐ionic liquid moieties

Novel poly(3,4‐ethylenedioxythiophene) (PEDOT) polymers bearing imidazolium‐ionic liquid moieties were synthesized by electrochemical polymerizations. For this purpose, new functional monomers were synthesized having an 3,4‐ethylenedioxythiophene (EDOT) unit and an imidazolium‐ionic liquid with different anions such as tetrafluoroborate (BF), bis(trifluoromethane)sulfonimide ((CF₃SO₂)₂N^?), and hexafluorophosphate (PF). Next, polymer films were obtained by electrochemical synthesis in dicholoromethane solutions. Obtained polymers were characterized, revealing the characteristics of PEDOT in terms of electrochemical and spectroelectrochemical properties, FTIR, ¹H NMR, and AFM microscopy. Interestingly, the hydrophobic character of electropolymerized films could be modified depending on the anion type. The hydrophobicity followed the trend PF > (CF₃SO₂)₂N^? > BF > pure PEDOT as determined by water contact angle measurements. Furthermore, the polymers could be dissolved in a range of polar organic solvents such as dimethylformamide, propylene carbonate, and dimethyl sulfoxide making these polymers interesting candidates for wet processing methods. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3010–3021, 2009     

Magnesium chloride-supported high-mileage catalysts for olefin polymerization XI. Determinations of poly(decene-1) molecular weight chain dimension and thermal transitions

Decene-1 was polymerized with the CW catalyst and fractionated by precipitation technique. Light-scattering and viscometric measurements on these fractions established the relationship [η] = 5.19 × 10^?3 M . The unperturbed mean square end-to-end distance is (〈R〉/M)^1/2 = (6.17 ± 0.34) × 10^?9. Light-scattering data is consistent with a relatively stiff molecule with length of L = 1.75 × 10^?5 cm for poly(decene-1) with MW = 397,000. Its mean square radius of gyration 〈R〉 is 2.79 × 10^?11 cm.² The ratio of L²/〈R〉 = 11 is close to the theoretical ratio of 12 for this kind of macromolecule.     

Heterogeneous surface saponification of suspension‐polymerized monodisperse poly(vinyl acetate) microspheres using various ions

Poly(vinyl alcohol) (PVA)/poly(vinyl acetate) (PVAc) microspheres with a skin/core structure were prepared through the heterogeneous surface saponification of PVAc microspheres suspension‐polymerized. The PVA skin formed through the heterogeneous saponification was hydrogel swellable in water. In addition, to obtain monodisperse PVA/PVAc microspheres having various skin/core ratios and morphologies, the ion‐specificities to the heterogeneous saponification were investigated using SO, Cl^?, NO, Br^?, and I^? for anions and Li⁺, Na⁺, and K⁺ for cations, respectively. The ions were not specific significantly to the rate of the heterogeneous saponification, while were related to the degree of saponification (DS). DSs had different values between by weight loss (DS_w) and by proton nuclear magnetic resonance spectroscopy (DS_NMR) measurements. The order of DS_ws was SO < Cl^? < NO < Br^? < I^? for anions and K⁺ < Na⁺ < Li⁺ for cations, and that of DS_NMRs, I^? < Br^? < NO < Cl^? < SO for anions and Li⁺ < Na⁺ < K⁺ for cations. The differences in values between DS_ws and DS_NMRs were caused by the dissolution of PVA skin and were significantly decreased for SO. The peaks at melting temperature of PVA were sharp and their areas were large for ions deswelling PVA skins.     

Chiral recognition in molecular and macromolecular pairs of (S)‐ and (R)‐1‐cyano‐2‐methylpropyl‐4′‐ {[4‐(8‐vinyloxyoctyloxy)benzoyl]oxy}biphenyl‐4‐ carboxylate enantiomers

(S)‐1‐Cyano‐2‐methylpropyl‐4′‐{[4‐(8‐vinyloxyoctyloxy)benzoyl]oxy}biphenyl‐ 4‐carboxylate [ (S)‐11 ] and (R)‐1‐cyano‐2‐methylpropyl‐4′‐{[4‐(8‐vinyloxyoctyloxy)benzoyl]oxy}biphenyl‐4‐carboxylate [( R)‐11 ] enantiomers, both greater than 99% enantiomeric excess, and their corresponding homopolymers, poly[ (S)‐11 ] and poly[ (R)‐11 ], with well‐defined molecular weights and narrow molecular weight distributions were synthesized and characterized. The mesomorphic behaviors of (S)‐11 and poly[ (S)‐11 ] are identical to those of (R)‐11 and poly[ (R)‐11 ], respectively. Both (S)‐11 and (R)‐11 exhibit enantiotropic S_A, S, and S_X (unidentified smectic) phases. The corresponding homopolymers exhibit S_A and S phases. The homopolymers with a degree of polymerization (DP) less than 6 also show a crystalline phase, whereas those with a DP greater than 10 exhibit a second S_X phase. Phase diagrams were investigated for four different pairs of enantiomers, (S)‐11 /( R)‐11 , (S)‐11 /poly[ (R)‐11 ], and poly[ (S)‐11 ]/poly[ (R)‐11 ], with similar and dissimilar molecular weights. In all cases, the structural units derived from the enantiomeric components are miscible and, therefore, isomorphic in the S_A and S phases over the entire range of enantiomeric composition. Chiral molecular recognition was observed in the S_A and S_X phases of the monomers but not in the S_A phase of the polymers. In addition, a very unusual chiral molecular recognition effect was detected in the S phase of the monomers below their crystallization temperature and in the S phase of the polymers below their glass‐transition temperature. In the S phase of the monomers above the melting temperature and of the polymers above the glass‐transition temperature, nonideal solution behavior was observed. However, in the S_A phase the monomer–polymer and polymer–polymer mixtures behave as an ideal solution. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3631–3655, 2000