Magnesium chloride supported high mileage catalysts for olefin polymerization. XII. Polymerization of ethylene

Polymerizations of ethylene by the MgCl₂/ethylbenzoate/p-cresol/AlEt₃ TiCl₄-AlEt₃/methyl-p-toluate (CW-catalyst) have been studied. The initially formed active site concentration, [Ti] has a maximum value of 50% of total titanium at 50°C and lower values at other temperatures. The Ti decays rapidly to Ti sites with conc. ca. 10 mol %/mol Ti. The rate constants for four chain transfer processes have been obtained at 50°C: for transfer with AlEt₃, k = 2.1 × 10^?4 s^?1 and k = 4.8 × 10^?4 s^?1; for transfer with monomer, k = 3.6 × 10^?3 (M s)^?1 and K = 8.3 × 10^?3 (M s)^?1; for β-hydride transfer, k = 7.2 × 10^?4 s^?1 and k = 4.9 × 10^?4 s^?1; and transfer with hydrogen, k = 4.0 × 10^?3 torr^1/2 s^? and k = 5.1 × 10^?3 torr^1/2 s^?1. The rate constants for the termination assisted by hydrogen is k = 1.7 (M^1/2 torr^1/2 S)^?1. If monomer is assisting termination as was observed for propylene polymerization, then k = 7.8 (M^3/2 s)^?1. Values of all the rate constants can be higher or lower at other temperatures. Detailed comparisons were made with the results of propylene polymerizations. There are more than four times as many Ti active sites for ethylene polymerization than there are for stereospecific polymerization of propylene; the difference is more than a factor of two for the Ti sites. Certain rate constants are nearly the same for both monomers while others are markedly different. Some of the differences can be explained by stereoelectronic effects.     

Magnesium chloride-supported high-mileage catalysts for olefin polymerization XI. Determinations of poly(decene-1) molecular weight chain dimension and thermal transitions

Decene-1 was polymerized with the CW catalyst and fractionated by precipitation technique. Light-scattering and viscometric measurements on these fractions established the relationship [η] = 5.19 × 10^?3 M . The unperturbed mean square end-to-end distance is (〈R〉/M)^1/2 = (6.17 ± 0.34) × 10^?9. Light-scattering data is consistent with a relatively stiff molecule with length of L = 1.75 × 10^?5 cm for poly(decene-1) with MW = 397,000. Its mean square radius of gyration 〈R〉 is 2.79 × 10^?11 cm.² The ratio of L²/〈R〉 = 11 is close to the theoretical ratio of 12 for this kind of macromolecule.     

Binding of uranyl ion by poly(ethylenimine) containing a salicylate derivative

Three molecules of 5-(bromoacetyl)salicylate ( 1 ) complexed to uranyl UO ion were crosslinked with branchy poly(ethylenimine) (PEI) in DMSO by alkylation of amino groups of PEI with 1, leading to the formation of UO₂(Sal) PEI. Upon demetalation of UO₂(Sal) PEI with HCl, apo(Sal) PEI was obtained. Based on the pH dependence of log K_f for UO₂(Sal) PEI, it was concluded that each uranyl binding site in UO₂(Sal) PEI or apo(Sal) PEI contains three salicylate moieties. In terms of the equilibrium constant for formation of the uranyl complex, apo(Sal) PEI was found to be comparable to or better than the previously reported effective uranophiles. In terms of the rates for the formation of the uranyl complex, however, apo(Sal) PEI was far superior to those other uranophiles. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2935–2942, 1997     

Syndiospecific polymerization of styrene. II. Monocyclopentadienyltributoxy titanium/methylaluminoxane catalyst

Syndiospecific polymerization of styrene was catalyzed by monocyclopentadienyltributoxy titanium/methylaluminoxane [CpTi (OBu)₃/MAO]. The atactic and syndiotactic polystyrenes were separated by extracting the former with refluxing 2-butanone. The activity and syndiospecificity of the catalyst were affected by changes in catalyst concentration and composition, polymerization temperature, and monomer concentration. Extremely high activity of 5 × 10⁷ g PS (mol Ti mol S h)^?1 with 99% yield of the syndiotactic product were achieved. The concentration of active species, [C^*], has been determined by radiolabeling. The amount of the syndiospecific and nonspecific catalytic species, [C] and [C] respectively, correspond to 79 and 13% of the CpTi(OBu)₃. The rate constants of propagation for C and C at 45°C are 10.8 and 2.0 (M s)^?1, respectively, the corresponding rate constants for chain transfer to MAO are 6.2 × 10^?4 and 4.3 × 10^?4s^?1. There was no deactivation of the catalytic species during a batch polymerization. The rate constant of chain transfer with monomer is 6.7 × 10^?2 (M s)^?1; the spontaneous β-hydride transfer rate constant is 4.7 × 10^?2 s^?1. The polymerization activity and stereospecificity of the catalyst are highest at 45°C, both decreasing with either higher or lower temperature. The stereoregular polymer have broad MW distributions, M?_w/M?_n = 2.8–5.7, and up to three crystalline modifications. The T_m of the s-PS polymerized at 0–90°C decreased from 261.8 to 241°C indicating thermally activated monomer insertion errors. The styrene polymerization behaviors were essentially insensitive to the dielectric constant of the medium.     

Primary radical termination and unimolecular termination in the heterogeneous polymerization of acrylamide initiated by a fluorinated azo‐derivative initiator: A kinetic study

Acrylamide was polymerized in acetonitrile at 82 °C with a perfluorinated azo‐derivative initiator. The polymerization proceeded heterogeneously. Varying amounts of initiator and monomer were used. The activation energy was deduced from three experiments carried out at 59, 71, and 82 °C. The following kinetic law, deviating a great deal from the classical law, was obtained: R ∼ [I₂][M](0.05% < [I₂]_o/[M]_o < 1.00%) and R ∼ [I₂][M](1% < [I₂]_o/[M]_o < 7%). These results can be interpreted in light of the contribution of primary radical termination and the emergence of occlusion. The development of a new kinetic relationship allowed us to confirm the existence of both of these termination reactions. The calculation of the k_prt /k_i · k_p ratio was also achieved. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1834–1843, 2000     

Electropolymerization of benzene and biphenyl in organic media: Influence of different parameters (solvent,water, acidity,salt) on the formation of polyparaphenylene films (PPP)

The electrosynthesis of polyparaphenylene films (PPP) by oxidation of benzene or biphenyl on a Pt electrode was studied in different organic media. Film formation was possible only if the solvent had acidic properties according to the Lewis concept, and if the water content of this medium was less than 5 × 10^?2M. Addition of an excess of P₂O₅ or CuCl₂ into the medium increased the acidity and improved the adherence and the homogeneity of the films considerably. PPP films were electroactive and conductive if the electrolysis was carried out in the presence of salts containing BF, SbF, PF anions; they were insulating with perchlorate salts. IR analysis of these polymers showed highly crosslinked structures and the chains were constituted of about 10 para coupled phenyl moieties.     

A chiral polymer‐based turn‐on fluorescent sensor for specific recognition of hydrogen sulfate

A new kind of polymeric chemosensor containing chiral naphthaldimine moiety in the side chain was synthesized by the reversible addition‐fragmentation chain transfer polymerization of N‐{[2‐(4‐vinylbenzyloxy)‐1‐naphthyl]‐methylene}‐(S)‐2‐phenylglycinol (VNP). The resulting polymers (PVNP) showed high selectivity for hydrogen sulfate relative to other anions including F^?, Cl^?, Br^?, H₂PO, CH₃CO, and NO in tetrahydrofuran (THF) solution as judged from UV?vis, fluorescence, and circular dichroism spectrophotometric titrations. Compared with its monomer, the polymer has proven to be more attractive for detection of HSO in terms of sensitivity and reproducibility. Upon addition of the anion it gives remarkable spectral responses concomitant with detectable color change from colorless to pale yellow. Furthermore, the HSO‐induced CD or fluorescence signal can be totally reversed with addition of base and eventually recovered the initial state, leading to a reproducible molecular switch with two distinguished “on” and “off” states. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Solvay type VCl3 isospecific catalysts

Solvay type S –VCl₃ catalyst has 7% of catalytically active vanadium sites ([C^*]) with k_p (rate constant of propagation) = 31 (M s)^?1 for ethylene polymerization. Addition of a comonomer, propylene of 4-methylpentene-1 (4-MP) significantly raised the ethylene polymerization activity. S –VCI₃ catalyst has very small amounts of catalytically active vanadium for propylene polymerizations: [C] = 0.19% with k_p,i = 857 (M s)^?1 and [C] = 0.45% with k_p,a = 23 (M s)^?1 for isospecific and nonspecific sites, respectively. Addition of a conomer, ethylene or 4-MP. lowered the propylene polymerization activity. S –VCI₃ is more easily reduced to the divalent ion by AIR₃ than S –TiCl₃. Methyl-p-toluate moderates the reducting power of AIR₃; it increase the productivity and stereoselectivity of the S –YiCl₃ catalyst, VCI₃ supported on MgCl₂ (CW–V catalyst) has enhanced rate constant of propylene polymerization but has the opposite effects on the S –TiCl₃ Catalyst. VCI₃ supported on MgCl₂ (CW–V catalyst) has enhances rate constant of propylene polymerization but only a minute fraction of the supported vanadiums are catalytically active: [C] = 0.019% and k_p,i = 1580 (Ms)^?1, [C] = 0.057% and k_p,i = 58 (M s)^?1. This is compared with far greater number of catalytically active titanium sites in the TiCl₃ supported on MgCl₂ catalyst: [C] = 6% and k_p,i = 200 (M s)^?1, [C] = 6% and k_p,a = 16(M s)^?1. Therefore, both the S –VCI₃ and CW–V catalysts are highly stereoselective but low in efficiency with respect to the utilization of the vanadium ion in the catalysis.     

Kinetics of crosslinking reactions. 2. Reaction rates of intermolecular and intramolecular crosslinkings by using a soluble microgel

Soluble microgels with several pendant vinyl groups were synthesised by radical copolymerization of methyl methacrylate (MMA) with p-divinyl benzene (p-DVB). The competitive reactions of intermolecular and intramolecular crosslinkings of these microgels were carried out at 40°C in the presence of 1-buten-3-ol as a degradative chain transfer agent. The rate constant of intermolecular crosslinking (k) was estimated by GPC (gel permeation chromatography) analysis on the polymer produced from intermolecular propagation between bimolecules. The k depended strongly on the internal structure of microgels. Network formation was discussd inclusive of informations for the rate constant of intramolecular crosslinking (k).     

Cationic grafting from carbon black. VIII. Cationic ring-opening polymerization and copolymerization of oxepane initiated by acylium perchlorate groups on carbon black

The cationic ring-opening polymerization of oxepane was found to be initiated by carbon black having acylium perchlorate (CO⁺CIO) groups, which were introduced by the reaction of acyl chloride groups with silver perchlorate. It was confirmed that polyoxepane, i.e., poly(oxyhexamethylene), was propagated from CO⁺CIO groups on carbon black and effectively grafted on the surface. The rate of the polymerization and the percentage of grafting of poly(oxyhexamethylene) remarkably increased by the addition of epichlorohydrin (ECH) as a promoter: the percentage of grafting in the presence of ECH increased to about 100% with an increase in conversion. Furthermore, CO⁺CIO groups on carbon black have an ability to initiate the cationic ring-opening copolymerization of oxepane with ECH to give poly(oxepane-co-ECH) with various composition. The ring-opening copolymerization of oxepane with phthalic anhydride was also initiated by CO⁺CIO groups to give polyether ester, i.e., poly(hexamethylene phthalate) containing poly(oxyhexamethylene) sequence. In the copolymerization, polyether or polyether ester was effectively grafted from carbon black based on the propagation of these polymers from CO⁺CIO groups.     

Anionic polymerization of N-substituted maleimide. V. A study on the kinetic features of anionic polymerization of N-phenylmaleimide

The kinetic feature of the anionic polymerization of N-PMI was investigated in THF. The polymerization system initiated with lithium tert-butoxide was revealed to be so-called “slow-initiation” system. The rate constant of the initiation reaction, k_i, was obtained to be 4.2 × 10^?3 (L mol^?1 s^?1) at ?72°C. The apparent rate constants of the propagation reaction, k, at ?72°C were individually obtained from each slope of the first-order plots in the later stages of the polymerizations for four different initiator concentrations. Each k is fairly close to that of initiation rate around 10^?3. The propagation reaction was concluded to be dominated by ion-pair mechanism from the analysis of the kinetic data and the results of the addition effects of crown ether and common salt.     

Magnesium chloride supported high-mileage catalysts for olefin polymerization. X. Effect of hydrogen and catalytic site deactivation

The effect of H₂ on propylene polymerization initiated by a MgCl₂/EB/PC/AlEt₃/TiCl₄–3 AlEt₃/MPT catalyst was studied. Hydrogen increases significantly the initial rate during the early stage of the polymerization to give a higher yield of polymer than reactions without H₂. But H₂ reduces the yield toward the latter stages so that the net effect on the total yield can be quite small. There is no appreciable effect of H₂ on either the isotacticity index or polydispersity of the products. It decreases molecular weight proportional to (p_H2)^1/2. The chain transfer by H₂ resulted in a decrease of total metal polymer bond concentration with time of polymerization. The rate constants of hydrogen chain transfer for the two kinds of isospecific and nonspecific sites are = 5.1 × 10^?3, = 2.7 × 10^?3, = 7.5 × 10^?3, = 4.4 × 10^?3, in units of torr^1/2 sec^?1 at 50°. Hydrogen assists in the deactivation of the catalytic sites as does propylene; rates of the former and the latter vary with (p_H2)^1/2 and [C₃H₆]^1/2, respectively, with k = (12.1 ± 0.9) M^?1 torr^?1/2 sec^?1 and k = (65.3 ± 3.3) M^?3/2 sec^?1 at 50° and A/T = 167. The mechanism for deactivation of catalytic sites are discussed.     

Magnesium chloride supported high mileage catalysts for olefin (decene-l) polymerization XIV. Propagation and chain transfer

Decene-l was polymerized with the MgCl₂/ethylebenzoate/p-cresol/AIEt₃/TiCl₄-AlEt₃/methyl-p-toluate catalyst at 50° using an A/T ratio of 167 and a range of monomer concentration. The concentration of the two kinds of active sites are [Ti] = 12% and [Ti] = 4% of the total titanium. The rate constants of propagation are 24 M^?1 s^?1. Chain transfers to AIEt₃, monomer, and by β-hydride elimination have rate constant values of 1.7 × 10^?3 M^?1 s^?1, 1.34 × 10^?2 M^?1 s^?1, and 1.7 × 10^?2 s^?1, respectively. Poly(decene-l) have relatively narrow MW which are unchanged during the course of a polymerization. Therefore, the active site concentrations in the CW catalyst for propylene and decene polymerization are identical and their rate constant values agree within a factor of 2. However, the rate of decene polymerization depends on fractional order of monomer concentration and decreases with the increase of activator concentration. Furthermore, the formation of metal polymer bonds has a rate independent of these concentrations. These kinetic behaviors are a manifestation of absorption processes of these species which are not seen in propylene polymerizations.     

Heterogeneous surface saponification of suspension‐polymerized monodisperse poly(vinyl acetate) microspheres using various ions

Poly(vinyl alcohol) (PVA)/poly(vinyl acetate) (PVAc) microspheres with a skin/core structure were prepared through the heterogeneous surface saponification of PVAc microspheres suspension‐polymerized. The PVA skin formed through the heterogeneous saponification was hydrogel swellable in water. In addition, to obtain monodisperse PVA/PVAc microspheres having various skin/core ratios and morphologies, the ion‐specificities to the heterogeneous saponification were investigated using SO, Cl^?, NO, Br^?, and I^? for anions and Li⁺, Na⁺, and K⁺ for cations, respectively. The ions were not specific significantly to the rate of the heterogeneous saponification, while were related to the degree of saponification (DS). DSs had different values between by weight loss (DS_w) and by proton nuclear magnetic resonance spectroscopy (DS_NMR) measurements. The order of DS_ws was SO < Cl^? < NO < Br^? < I^? for anions and K⁺ < Na⁺ < Li⁺ for cations, and that of DS_NMRs, I^? < Br^? < NO < Cl^? < SO for anions and Li⁺ < Na⁺ < K⁺ for cations. The differences in values between DS_ws and DS_NMRs were caused by the dissolution of PVA skin and were significantly decreased for SO. The peaks at melting temperature of PVA were sharp and their areas were large for ions deswelling PVA skins.     

Lactide polymerization activity of alkoxide,phenoxide, and amide derivatives of yttrium(III) arylamidinates

In quest of new, single‐site catalysts for cyclic ester polymerizations, a series of mononuclear yttrium(III) complexes of N,N′‐bis(trimethylsilyl)benzamidinate ([L^TMS]⁻) and hindered N,N′‐bis‐(2,6‐dialkylaryl)toluamidinates ([L^Et]⁻, aryl = Et₂C₆H₃, and [L^iPr]⁻, aryl = ⁱPr₂C₆H₃) were synthesized and characterized by X‐ray diffraction: LY(μ‐Cl)₂Li(TMEDA) ( 1 ), LY(OC₆H₂^tBu₂Me) ( 2 ), LY(OC₆H₃Me₂)₂Li(THF)₄ ( 3 ), LY(μ‐O^tBu)₂Li(THF) ( 4 ), L^iPrY[N(SiMe₂H)₂]₂(THF) ( 5 ), LY(THF)(Cl)(μ‐Cl)Li(THF)₃ ( 6 ), and LY[N(SiMe₂H)₂] ( 7 ). Coordination numbers ranging from five to seven were observed, and they appeared to be controlled by the steric bulk of the supporting amidinate and alkoxide, phenoxide, or amide coligands. Complexes 2 – 5 and 7 are active catalysts for the polymerization of D,L ‐lactide (e.g., with 2 and added benzyl alcohol, 1000 equiv of D,L ‐lactide were polymerized at room temperature in less than 1 h, with polydispersities less than 1.5). The neutral complexes 2 , 5 , and 7 were more effective than the anionic complexes 3 and 4 . In addition, the presence of the more hindered amidinate ligands [L^Et]⁻ and [L^iPr]⁻ on yttrium‐amides slowed the polymerizations ( 7 < 5 < Y[N(SiMe₂H)₂]₃). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 284–293, 2001     

Visible light induced free radical promoted cationic polymerization using thioxanthone derivatives

The free radical promoted cationic polymerization cyclohexene oxide (CHO), was achieved by visible light irradiation (λ_inc = 430–490 nm) of methylene chloride solutions containing thioxanthone‐fluorene carboxylic acid (TX‐FLCOOH) or thioxanthone‐carbazole (TX‐C) and cationic salts, such as diphenyliodonium hexafluorophosphate (Ph₂I⁺PF) or silver hexafluorophosphate (Ag⁺PF) in the presence of hydrogen donors. A feasible initiation mechanism involves the photogeneration of ketyl radicals by hydrogen abstraction in the first step. Subsequent oxidation of ketyl radicals by the oxidizing salts yields Bronsted acids capable of initiating the polymerization of CHO. In agreement with the proposed mechanism, the polymerization was completely inhibited by 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy and di‐2,6‐di‐tert‐butylpyridine as radical and acid scavengers, respectively. Additionally polymerization efficiency was directly related to the reduction potential of the cationic salts, that is, Ag⁺PF (E = +0.8 V) was found to be more efficient than Ph₂I⁺PF (E = ?0.2 V). In addition to CHO, vinyl monomers such as isobutyl vinyl ether and N‐vinyl carbazole, and a bisepoxide such as 3,4‐epoxycyclohexyl‐3′,4′‐epoxycyclohexene carboxylate, were polymerized in the presence of TX‐FLCOOH or TX‐C and iodonium salt with high efficiency. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterizations of well‐defined branched polymers with AB2 branches by combination of RAFT polymerization and ROP as well as ATRP

A well‐defined branched copolymer with PLLA‐b‐PS₂ branches was prepared by combination of reversible addition‐fragmentation transfer (RAFT) polymerization, ring‐opening polymerization (ROP), and atom transfer radical polymerization (ATRP). The RAFT copolymerization of methyl acrylate (MA) and hydroxyethyl acrylate (HEA) yielded poly(MA‐co‐HEA), which was used as macro initiator in the successive ROP polymerization of LLA. After divergent reaction of poly(MA‐co‐HEA)‐g‐PLLAOH with divergent agent, the macro initiator, poly(MA‐co‐HEA)‐g‐PLLABr₂ was formed in high conversion. The following ATRP of styrene (St) produced the target polymer, poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). The structures, molecular weight, and molecular weight distribution of the intermediates and the target polymers obtained from every step were confirmed by their ¹H NMR and GPC measurements. DSC results show one T = 3 °C for the poly(MA‐co‐HEA), T = ?5 °C, T= 122 °C, and T = 157 °C for the branched copolymers (poly(MA‐co‐HEA)‐g‐PLLA), and T = 51 °C, T = 116 °C, and T = 162 °C for poly(MA‐co‐HEA)‐g‐(PLLA‐b‐PS₂). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 549–560, 2006     

Kinetics and mechanism of the cationic polymerization of trioxane. I. Crystallization during polymerization

Cationic polymerizations of trioxane in 1,2‐ethylene dichloride and benzene were heterogeneous and reversible. Phase separation accompanying with crystallization occurred during the polymerization. Three morphological changes were found in the course of the polymerization as were investigated by dilatometry and precipitation method. Based on the findings of morphological changes and three reversible processes for the polymerization, a rate equation was proposed to describe the polymerization. The proposed rate equation was fairly good in describing the experimental data, and kinetics constants including K_p, K_d, K_p′, K_d′, M, M, and K_dis/K_cr for the polymerization at 30, 40, and 50°C in 1,2‐ethylene dichloride and benzene were obtained. Factors that affected the kinetics constants were discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 483–492, 1999     

Electrochemical synthesis of PEDOT derivatives bearing imidazolium‐ionic liquid moieties

Novel poly(3,4‐ethylenedioxythiophene) (PEDOT) polymers bearing imidazolium‐ionic liquid moieties were synthesized by electrochemical polymerizations. For this purpose, new functional monomers were synthesized having an 3,4‐ethylenedioxythiophene (EDOT) unit and an imidazolium‐ionic liquid with different anions such as tetrafluoroborate (BF), bis(trifluoromethane)sulfonimide ((CF₃SO₂)₂N^?), and hexafluorophosphate (PF). Next, polymer films were obtained by electrochemical synthesis in dicholoromethane solutions. Obtained polymers were characterized, revealing the characteristics of PEDOT in terms of electrochemical and spectroelectrochemical properties, FTIR, ¹H NMR, and AFM microscopy. Interestingly, the hydrophobic character of electropolymerized films could be modified depending on the anion type. The hydrophobicity followed the trend PF > (CF₃SO₂)₂N^? > BF > pure PEDOT as determined by water contact angle measurements. Furthermore, the polymers could be dissolved in a range of polar organic solvents such as dimethylformamide, propylene carbonate, and dimethyl sulfoxide making these polymers interesting candidates for wet processing methods. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3010–3021, 2009     

Role of anions in the polymerization of 2,5‐dimethoxyaniline in the presence of poly(styrene sulfonic acid)

Poly(2,5‐dimethoxyaniline) (PDMA)–Ag composites were successfully obtained through the oxidative polymerization of 2,5‐dimethoxyaniline in poly(styrene sulfonic acid) with CH₃SO₃Ag and AgNO₃ as oxidants. In situ ultraviolet–visible spectroscopy results showed that the growth rate of PDMA was strongly affected by CH₃SO and NO. The coupling reaction of PDMA and NO was proposed to explain the lower growth rate of PDMA with AgNO₃ as the oxidant in comparison with CH₃SO₃Ag. X‐ray photoelectron spectroscopy and Fourier transform infrared spectroscopy were used to validate the proposed coupling reaction through the monitoring of the side products and oxidized state of PDMA. The results showed that there were more side products and lower oxidized states for the composite structure in the presence of NO than in the presence of CH₃SO, and this agreed with the proposal. Transmission electron microscopy showed that the Ag nanoparticles had almost the same size, regardless of the anions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6624–6632, 2006