A dislocation-based constitutive law for pure Zr including temperature effects

In this work, a single crystal constitutive law for multiple slip and twinning modes in single phase hcp materials is developed. For each slip mode, a dislocation population is evolved explicitly as a function of temperature and strain rate through thermally-activated recovery and debris formation and the associated hardening includes stage IV. A stress-based hardening law for twin activation accounts for temperature effects through its interaction with slip dislocations. For model validation against macroscopic measurement, this single crystal law is implemented into a visco-plastic-self-consistent (VPSC) polycrystal model which accounts for texture evolution and contains a subgrain micromechanical model for twin reorientation and morphology. Slip and twinning dislocations interact with the twin boundaries through a directional Hall–Petch mechanism. The model is adjusted to predict the plastic anisotropy of clock-rolled pure Zr for three different deformation paths and at four temperatures ranging from 76 K to 450 K (at a quasi-static rate of 10⁻³ 1/s). The model captures the transition from slip-dominated to twinning-dominated deformation as temperature decreases, and identifies microstructural mechanisms, such as twin nucleation and twin–slip interactions, where future characterization is needed.     

The effect of time-dependent twinning on low temperature (<0.25 ∗ Tm) creep of an alpha-titanium alloy

The low-temperature (less than one-fourth of the melting temperature) creep deformation behavior of hexagonally close-packed (HCP) α-Ti–1.6 wt.% V was investigated. Creep tests were performed at various temperatures between room temperature and 205 °C at 95% of the respective yield stress at the different temperatures. The creep strain rate was found to increase with increasing temperature. Scanning and transmission electron microscopy revealed that slip and unusually slow twin growth, or time-dependent twinning, are active deformation mechanisms for the entire temperature range of this investigation. The activation energy for creep of this alloy was calculated to identify the rate-controlling deformation mechanism, and was found to increase with increasing creep strain. At low strain, the activation energy for creep was found to be close to the previously calculated activation energy for slip. At high strain, the calculated activation energy indicates that both slip and twinning are significant deformation mechanisms. The appearance of twinning at high strains is explained by a model for twin nucleation by dislocation pileups.     

Crystal plasticity modeling of slip activity in Ti–6Al–4V under high cycle fatigue loading

Deformation micromechanisms of a Ti–6Al–4V alloy under fatigue loading at room temperature are studied using a three-dimensional crystal plasticity constitutive model. The model employs a minimum set of fitting parameters based on experimental data for Ti–6Al–4V. Single slip is strongly favored through a softening law that affects mainly the driving force for slip on the first activated slip system. Cyclic deformation behavior at the macroscopic scale and at the local scale of grains is analyzed through the simulation of 20 cycles of fatigue on a polycrystalline structure of 900 randomly oriented grains. The progressive activation of slip (basal, prismatic, and pyramidal) is analyzed and compared to experimental observations.     

Micromechanical quantification of elastic,twinning, and slip strain partitioning exhibited by polycrystalline,monoclinic nickel–titanium during large uniaxial deformations measured via in-situ neutron diffraction

We draw upon existing knowledge of twinning and slip mechanics to develop a diffraction analysis model that allows for empirical quantification of individual deformation mechanisms to the macroscopic behaviors of low symmetry and phase transforming crystalline solids. These methods are applied in studying elasticity, accommodation twinning, deformation twinning, and slip through neutron diffraction data of tensile and compressive deformations of monoclinic NiTi to ~18% true strain. A deeper understanding of tension–compression asymmetry in NiTi is gained by connecting crystallographic calculations of polycrystalline twinning strains with in situ diffraction measurements. Our analyses culminate in empirical, micromechanical quantification of individual elastic, accommodation twinning, deformation twinning, and slip contributions to the total macroscopic stress–strain response of a monoclinic material subjected to large deformations. From these results, we find that 20–40% of the total plastic response at high strains is due to deformation twinning and 60–80% due to slip.     

Modeling finite deformations in trigonal ceramic crystals with lattice defects

A model is developed for thermomechanical behavior of defective, low-symmetry ceramic crystals such as α$\alpha$-corundum. Kinematics resolved are nonlinear elastic deformation, thermal expansion, dislocation glide, mechanical twinning, and residual lattice strains associated with eigenstress fields of defects such as dislocations and stacking faults. Multiscale concepts are applied to describe effects of twinning on effective thermoelastic properties. Glide and twinning are thermodynamically irreversible, while free energy accumulates with geometrically necessary dislocations associated with strain and rotation gradients, statistically stored dislocations, and twin boundaries. The model is applied to describe single crystals of corundum. Hardening behaviors of glide and twin systems from the total density of dislocations accumulated during basal slip are quantified for pure and doped corundum crystals. Residual lattice expansion is predicted from nonlinear elasticity and dislocation line and stacking fault energies.     

On the strain hardening and texture evolution in high manganese steels: Experiments and numerical investigation

We present a systematic investigation on the strain hardening and texture evolution in high manganese steels where twinning induced plasticity (TWIP) plays a significant role for the materials' plastic deformation. Motivated by the stress–strain behavior of typical TWIP steels with compositions of Fe, Mn, and C, we develop a mechanistic model to explain the strain-hardening in crystals where deformation twinning dominates the plastic deformation. The classical single crystal plasticity model accounting for both dislocation slip and deformation twinning are then employed to simulate the plastic deformation in polycrystalline TWIP steels. While only deformation twinning is activated for plasticity, the simulations with samples composed of voronoi grains cannot fully capture the texture evolution of the TWIP steel. By including both twinning deformation and dislocation slip, the model is able to capture both the stress–strain behaviors and the texture evolution in Fe–Mn–C TWIP steel in different boundary-value problems. Further analysis on the strain contributions by both mechanisms suggests that deformation twinning plays the dominant role at the initial stage of plasticity in TWIP steels, and dislocation slip becomes increasingly important at large strains.     

A crystal plasticity model for strain-path changes in metals

A model is proposed that deals with the transient mechanical anisotropy during strain-path changes in metals. The basic mechanism is assumed to be latent hardening or softening of the slip systems, dependent on if they are active or passive during deformation, reflecting microstructural mechanisms that depend on the deformation mode rather than on the crystallography. The new model captures the experimentally observed behaviour of cross hardening in agreement with experiments for an AA3103 aluminium alloy. Generic results for strain reversals qualitatively agree with two types of behaviour reported in the literature – with or without a plateau on the stress–strain curve. The influence of the model parameters is studied through detailed calculations of the response of three selected parameter combinations, including the evolution of yield surface sections subsequent to 10% pre-strain. The mathematical complexity is kept to a minimum by avoiding explicit predictions related directly to underpinning microstructural changes. The starting point of the model is a combination of conventional texture and work hardening approaches, where an adapted full-constraints Taylor theory and a simple single-crystal work-hardening model for monotonic strain are used. However, the framework of the model is not restricted to these particular models.     

U–6Nb shear stress relaxation in compression waves (IJP 585-AV)

When uranium alloyed with 6-wt% niobium (U–6Nb) is rapidly compressed in uniaxial strain experiments, shear stress is observed to relax with a characteristic time of 30 ± 7 ns. In shock wave experiments, this relaxation inhibits the development of an elastic precursor commonly seen in other materials. When U–6Nb is cold-rolled to pre-twin and significantly increase the density of dislocations in the material, stress relaxation effects are diminished suggesting that twinning causes relaxation in the un-worked material. Separate ramp wave compression experiments produce effects that agree with those observed in shock-loading experiments. A phenomenological model is introduced that allows accurate simulation of all experiments. Estimates of residual shear stress after relaxation are obtained.     

Numerical modeling of formability of extruded magnesium alloy tubes

In this paper, a constitutive framework based on a rate-dependent crystal plasticity theory is employed to simulate the large strain deformation phenomena in hexagonal closed-packed (HCP) metals such as magnesium. The new framework is incorporated into in-house codes. Simulations are performed using the new crystal plasticity model in which crystallographic slip and deformation twinning are the principal deformation mechanisms. Simulations of various stress states (uniaxial tension, uniaxial compression and the so-called ring hoop tension test) for the magnesium alloy AM30 are performed and the results are compared with experimental observations of specimens deformed at 200 °C. Numerical simulations of forming limit diagrams (FLDs) are also performed using the Marciniak–Kuczynski (M–K) approach. With this formulation, the effects of crystallographic slip and deformation twinning on the FLD can be assessed.     

Cyclic behavior of extruded magnesium: Experimental, microstructural and numerical approach

The present study aims at determining the influence of cyclic straining on the behavior of pure extruded magnesium. For this purpose, tensile, compressive and cyclic tests are performed (small plastic strains are applied (Δε^p/2 = 0.1% and 0.4%). Deformation mechanisms (slip and twin systems) have been observed by TEM and the different critical resolved shear stress (CRSS) have been determined. Based on microscopic observations, a crystal-plasticity-based constitutive model has been developed. The asymmetry between tensile and compressive loadings mainly results from the activation of hard slip systems in tension (such as 〈a〉 pyramidal and prismatic and 〈c + a〉 pyramidal glides) and twinning in compression. It is shown that basal slip is very easy to activate even for small Schmid factors. Numerical simulations reveal that untwinning in tension subsequent to compression must be considered to correctly fit the experimental S-shaped hysteresis curves. TEM observations indicate also intense secondary slips or twins inside the mother twins under cyclic conditions, so that twinning in compression and dislocation glide in tension are affected by cycling. The polycrystalline model allows to predict slip activities and twin volume fraction evolutions.     

Geometrically necessary dislocation structure organization in FCC bicrystal subjected to cyclic plasticity

Crystal plasticity finite element analysis of cyclic deformation of compatible type FCC bicrystals are performed. The model specimen used in the analysis is a virtual FCC bicrystal with an isotropic elastic property; therefore, the effect of constraint due to elastic incompatibility does not appear. The results of the analysis show the strain-amplitude-dependence of both the organization of the GND structure and the stress–strain behavior. The calculated stress–strain curve with the largest strain amplitude shows additional cyclic hardening. The microscopic mechanisms of the strain-amplitude-dependent organization of the GND structure and additional cyclic hardening behavior are discussed in terms of the activation of secondary slip system(s). Finally, the effects of the elastic anisotropy, the lattice friction stress and the interaction between dislocations are also argued.     

Characterization of yielding behavior of polycrystalline metals with single crystal plasticity based on representative characteristic length

Single crystal plasticity based on a representative characteristic length is proposed and introduced into a homogenization approach based on finite element analyses, which are applied to characterization of distinctive yielding behaviors of polycrystalline metals, yield-point elongation, and grain size strengthening. The computational manner for an implicit stress update is derived with the framework of a standard multi-surface plasticity at finite strain, where the evolution of the characteristic lengths are numerically converted from the accumulated slips of all of slip systems by exploiting the mathematical feature of the characteristic length as the intermediate function of the plastic internal variables. Furthermore, a constitutive model for a single crystal reproduces the stress–strain curve divided into three parts. Using two-scale finite element analysis, the macroscopic stress–strain response with yield-point elongation under a situation of low dislocation density is reproduced. Finally, the grain size effect on the yield strength is analyzed with modeling of the grain boundary in the context of the proposed constitutive model and is discussed from both macroscopic and microscopic views.     

Debonding failure and size effects in micro-reinforced composites

Failure in micro-reinforced composites is investigated numerically using the strain-gradient plasticity theory of Gudmundson [Gudmundson, P., 2004. A unified treatment of strain gradient plasticity. Journal of the Mechanics and Physics of Solids 52 (6) 1379–1406] in a plane strain visco-plastic formulation. Bi-axially loaded unit cells are used and failure is modeled using a cohesive zone at the reinforcement interface. During debonding a sudden stress drop in the overall average stress–strain response is observed. Adaptive higher-order boundary conditions are imposed at the reinforcement interface for realistically modeling the restrictions on moving dislocations as debonding occurs. It is found that the influence of the imposed higher-order boundary conditions at the interface is minor. If strain-gradient effects are accounted for a void with a smooth shape develops at the reinforcement interface while a smaller void having a sharp tip nucleates if strain-gradient effects are excluded. Using orthogonalization of the plastic strain gradient with three corresponding material length scales it is found that, the first length scale dominates the evaluated overall average stress–strain response, the second one only has a small effect and the third one has an intermediate effect. Finally, studies of reinforcement having elliptical cross-sections show rather significant gradients of stress which is not seen for the corresponding circular cross-sections. Also, an increased drop in the overall load carrying capacity is observed for cross-sections elongated perpendicular to the principal tensile direction compared to the corresponding circular cross-sections.     

Effects of texture on shear band formation in plane strain tension/compression and bending

In this study, effects of typical texture components observed in rolled aluminum alloy sheets on shear band formation in plane strain tension/compression and bending are systematically studied. The material response is described by a generalized Taylor-type polycrystal model, in which each grain is characterized in terms of an elastic–viscoplastic continuum slip constitutive relation. First, a simple model analysis in which the shear band is assumed to occur in a weaker thin slice of material is performed. From this simple model analysis, two important quantities regarding shear band formation are obtained: i.e. the critical strain at the onset of shear banding and the corresponding orientation of shear band. Second, the shear band development in plane strain tension/compression is analyzed by the finite element method. Predictability of the finite element analysis is compared to that of the simple model analysis. Third, shear band developments in plane strain pure bending of a sheet specimen with the typical textures are studied. Regions near the surfaces in a bent sheet specimen are approximately subjected to plane strain tension or compression. From this viewpoint, the bendability of a sheet specimen may be evaluated, using the knowledge regarding shear band formation in plane strain tension/compression. To confirm this and to encompass overall deformation of a bent sheet specimen, including shear bands, finite element analyses of plane strain pure bending are carried out, and the predicted shear band formation in bent specimens is compared to that in the tension/compression problem. Finally, the present results are compared to previous related studies, and the efficiency of the present method for materials design in future is discussed.     

A three-dimensional crystal plasticity model for duplex Ti–6Al–4V

A rate dependent crystal plasticity model for the α/β Ti–Al alloy Ti–6Al–4V with duplex microstructure is developed and presented herein. Duplex Ti–6Al–4V is a dual-phase alloy consisting of an hcp structured matrix primary α-phase and secondary lamellar α + β domains that are composed of alternating layers of secondary α laths and bcc structured residual β laths. The model accounts for distinct three-dimensional slip geometry for each phase, anisotropic and length scale dependent slip system strengths, the non-planar dislocation core structure of prismatic screw dislocations in the primary α-phase, and crystallographic texture. The model is implemented in the general purpose finite element code (ABAQUS, 2005. Ver 6.5, Hibbitt, Karlsson, and Sorensen, Inc., Pawtucket, RI) via a UMAT subroutine.     

Multiscale modeling of the plasticity in an aluminum single crystal

This paper describes a numerical, hierarchical multiscale modeling methodology involving two distinct bridges over three different length scales that predicts the work hardening of face centered cubic crystals in the absence of physical experiments. This methodology builds a clear bridging approach connecting nano-, micro- and meso-scales. In this methodology, molecular dynamics simulations (nanoscale) are performed to generate mobilities for dislocations. A discrete dislocations numerical tool (microscale) then uses the mobility data obtained from the molecular dynamics simulations to determine the work hardening. The second bridge occurs as the material parameters in a slip system hardening law employed in crystal plasticity models (mesoscale) are determined by the dislocation dynamics simulation results. The material parameters are computed using a correlation procedure based on both the functional form of the hardening law and the internal elastic stress/plastic shear strain fields computed from discrete dislocations. This multiscale bridging methodology was validated by using a crystal plasticity model to predict the mechanical response of an aluminum single crystal deformed under uniaxial compressive loading along the [4 2 1] direction. The computed strain-stress response agrees well with the experimental data.     

A continuum model for initiation and evolution of deformation twinning

Within continuum dislocation theory the plastic deformation of a single crystal with one active slip system under plane-strain constrained shear is investigated. By introducing a twinning shear into the energy of the crystal, we show that in a certain range of straining the formation of deformation twins becomes energetically preferable. An energetic threshold for the onset of twinning is determined. A rough analysis qualitatively describes not only the evolving volume fractions of twins but also their number during straining. Finally, we analyze the evolution of deformation twins and of the dislocation network at non-zero dissipation. We present the corresponding stress-strain hysteresis, the evolution of the plastic distortion, the twin volume fractions and the dislocation densities.     

Elastic/crystalline viscoplastic finite element analyses of single- and poly-crystal sheet deformations and their experimental verification

The elastic/crystalline viscoplastic constitutive equation, based on a newly proposed hardening-softening evolution equation, is introduced into the dynamic-explicit finite element code “Itas-Dynamic.” In the softening evolution equation, the effective distance and the angle between each slip system of a crystal are introduced to elucidate the interaction between the slip systems, which causes a decrease of dislocation density. The polycrystal sheet is modeled by Voronoi polygons, which correspond to the crystal grains; and by the selected orientations, which can relate to the texture, they are assigned to the integration points of the finite elements. We propose a direct crystal orientation assignment method, which means that each integration point of finite element has an assigned orientation, and its orientation can be rotated independently. Therefore, this inhomogeneous polycrystal model can consider the plastic induced texture development and subsequent anisotropy evolution. The parameters of the constitutive equation are identified by uni-axial tension tests carried out on single crystal sheets. Numerical results obtained for sheet tensions are compared with experimental ones to confirm the validity of our finite element code. Further, we investigate the following subjects: (1) how the initial orientation of single crystal affects slip band formation and strain localization; (2) how the grain size and particular orientations of the grain affect the strain localization in case of a polycrystal sheet. It is confirmed that the orientation of a single crystal can be related to the primary slip system and the deformation induced activation of that system, which in turn can be related to the slip band formation of the single crystal sheet. Further, in case of a polycrystal sheet, the larger the grain size, the more the strain localizes at a specific crystal, which has the particular orientation. It is confirmed through comparisons with experiments that our finite element code can predict the localization of strain in sheets and consequently can estimate the formability of sheet metals.