Polyisobutylene‐based polyurethanes. II. Polyureas containing mixed PIB/PTMO soft segments

The design, synthesis, characterization, and structure–property behavior of polyureas containing novel soft segments of mixed polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) chains and conventional hard segments is presented. Modest amounts (12%) of PTMO in the soft PIB phase significantly increase both the tensile strength and elongation of the polyureas. These polyureas exhibit not only oxidative/hydrolytic stabilities far superior to Bionate® and Elast‐Eon® considered the most oxidatively stable polyurethanes on the market but also display mechanical properties (29 MPa tensile strength and 200% elongation) approaching those of conventional thermoplastic polyurethanes. The surfaces of these polyureas are covered/protected by PIB segments, which will lead to excellent biocompatibility. Our results demonstrate that the PTMO segments facilitate stress transfer from the continuous mixed soft phase to the dispersed hard phase, which strengthens and flexibilizes PIB‐based polyureas and thus significantly improves elastomeric properties without compromising oxidative and hydrolytic stability. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2787–2797, 2009     

COMPATIBILITY OF PVC WITH POLYURETHANES OF DIFFERENT SOFT SEGMENTS

Blends of PVC and polyurethanes with four different soft segments of molecular weight 1000 were prepared and studied by dynamic mechanical and DSC techniques. It was found that the compatibility of PVC with segmented polyurethanes was related to the mixing of PVC molecules and the soft segments of the polyurethanes. Polyester based polyurethanes are more compatible with PVC than polyether based polyurethanes. Solution cast blends of PVC with PCL-polyurethane (1/2/1) exhibit single and narrow glass transition, while the blends with PPO-polyurethane (1/2/1) are completely incompatible. The compatibility was found to decrease with increasing hard segment content for all the polyurethanes used. The methods of blend preparation may change the compatibility of PVC/PU blends through their influence on the mixing or demixing of the hard and soft segments.     

Morphology and Mechanical Properties of Thermoplastic Polyurethanes Containing Polyisobutylene/Poly(tetramethylene oxide) Mixed Segments

We investigated the thermal properties, microphase separated structure and mechanical properties of a series of thermoplastic polyurethanes (TPUs) containing both polyisobutylene (PIB) and poly(tetramethylene oxide) (PTMO) diols in the soft segment (SS). A series of TPUs were prepared with the same weight fraction of the SS but different ratio between PIB and PTMO diols. Molecular weight of the PTMO diol and chemical structure of the hard segment (HS) also varied. Dynamic mechanical analysis (DMA) measurements did not reveal strong microphase separation between PIB and PTMO in the SS. While it has been assumed that incorporating PTMO diol into the SS can enhance the phase mixing between the hard segment (HS) and SS, our results indicated that, in most cases, the degree of microphase separation of TPUs based on mixed diols is slightly higher than that of TPUs based on only PIB diol.     

Effect of soft segment length on properties of fluorinated polyurethanes

The effects of soft segment length on the variations in morphology, surface composition, and hydrophilicity have been studied in fluorinated polyurethanes (FPUs) and correlated with their preliminary blood compatibility as evidenced by in vitro platelet adhesion experiments. The fluorinated polyurethanes were obtained using hexamethylene diisocyanate (HDI) and chain extender of 2,2,3,3-tetrafluoro-1,4-butanediol (TF) as the hard segment as well as various soft segments—polytetramethyl oxides (PTMO) with molecular weights of 650, 1000, 1400, and 2000. The increased phase separation in hard-segment domains with lengthening soft segment was observed by FT-IR, which is believed to result in enhanced strength of hydrogen bonds and good hard-segment order arrangement. Thin-film XRD results indicate at least three lateral distances existing between adjacent hard segments in the crystallized hard segment. Their distribution depends strongly on the length of soft segment. Lengthening soft segment promotes the formation of dense arrangement of crystallized hard segments. Compared with the effect of phase separation, surface composition was found to exert a major influence on the preliminary blood compatibility of fluorinated polyurethanes. Increasing fluorine content by decreasing soft segment length promotes reduction in platelet adhesion and activation on polyurethane surfaces.     

Polyisobutylene‐based polyurethanes. III. Polyurethanes containing PIB/PTMO soft co‐segments

The synthesis, characterization, and structure–property behavior of polyurethanes containing polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) soft co‐segments and bis(4‐isocyanatocyclohexyl)methane (HMDI)/hexanediol (HDO) hard segments is presented. The mechanical (stress/strain, hardness, and hysteresis) properties of these novel polyurethanes were investigated over a broad composition range. PIB‐based polyurethanes with HMDI/HDO hard segments showed better mechanical properties than earlier polyurethanes containing highly crystalline hard segments. The addition of moderate amounts (20% by weight) of PTMO significantly increased both tensile strengths and elongation. In the presence of larger amounts of PIB, these polyurethanes are expected to possess oxidative/hydrolytic/enzymatic stabilities superior to commercially available polyurethanes. These polyurethanes are softer and exhibit hysteresis superior to or comparable with conventional polyurethanes. According to initial thermal studies, these materials show good melt processibility. Overall, the mechanical properties of PIB based hybrid polyurethanes are similar to commercially important polyurethane type biomaterials. Our results show that the incorporation of PTMO segments to PIB‐based polyurethanes significantly improves elastomeric properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5278–5290, 2009     

Poly(urethane-oxazolidone): Synthesis, characterisation and shape memory properties

Poly(urethane-oxazolidone) were synthesized by reacting isocyanate-terminated oxazolidone with hydroxy-telechelic poly(tetramethylene oxide) (PTMO). The molar ratios of the reactants were varied to get polymers of varying oxazolidone and urethane compositons. The polymers were characterized by DSC, FTIR, XRD, dynamic mechanical thermal analysis and chemical analyses. An increase in the concentration of urethane and oxazolidone groups caused a decrease in tensile strength and elongation of the poly(urethane-oxazolidone). The polymers possessed crystallites of PTMO whose melting transition temperature decreased on enhancing the oxazolidone concentration. The polymers exhibited thermo-responsive shape memory properties, which was confirmed and quantified by cyclic tensile tests. The influence of oxazolidone modification and the consequent soft/hard segment variation on the thermal, mechanical, dynamic-mechanical and shape recovery properties of the resultant polymers was investigated. The oxazolidone moities conferred enhanced shape recovery and shape fixity to the polyurethane.     

聚乙二醇型聚氨酯软硬段对其相变储热性能的影响

以不同分子量的聚乙二醇(PEG)为软段,MDI-BDO为硬段,采用两步法溶液聚合合成一种具有固-固相变储热性能的聚氨酯材料.通过DSC,WAXD等测试手段对体系的软硬段结晶性,微相分离,相变可逆性及循环热稳定性进行研究,结果表明,聚氨酯中硬段的存在对软段结晶有着很大的影响,当软段分子量达到2000或以上时,软段才具有较大的结晶度和熔融相变焓,且硬段含量必须高于一定值才能形成较为完善的物理交联网络以保证材料在发生相变时维持固体状态.同时符合这两个条件的试样能具有较好的固-固相变储热性能.就软段PEG含量及分子量对材料储热性能的影响进行了研究,通过调节软段含量与分子量得到一系列具有不同相变焓和相变温度的聚氨酯固-固相变储热材料.经测试还发现,该材料具备很好的相变可逆性和循环热稳定性,是一类很有开发前景的相变储热材料.     

PIB‐based polyurethanes. IV. The morphology of polyurethanes containing soft co‐segments*

Novel polyurethanes consisting of polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) or PIB/poly(hexamethylene carbonate) (PC) soft co‐segments in combination with 4,4′‐methylene‐bis(cyclohexyl isocyanate)/1,6‐hexanediol, 1,4‐butanediol, or 1,6‐hexamethylene diamine hard segments exhibit excellent mechanical properties (upto 31 MPa tensile strength with 700% elongation) together with unprecedented oxidative/hydrolytic stability. A structural model of the morphology of these polyurethanes was developed that reflects this combination of properties. The key new elements of our model are H bridges between the PTMO and PC type soft and urethane hard segments, which compatibilize the soft and hard domains, and the presence of large quantities of chemically resistant PIB soft segments that protect the other oxidatively/hydrolytically vulnerable constituents. A variety of FTIR, DSC, SAXS, AFM, and DMTA experiments strongly support the proposed morphological model. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6180–6190, 2009     

Morphology and tensile properties of model thermoplastic polyurethanes with MDI/butanediol based monodisperse hard segments

Morphology and tensile properties of model thermoplastic polyurethanes (TPUs) containing polyisobutylene (PIB) or poly(tetramethylene oxide) (PTMO) based soft segment and 4,4‐methylene bis(phenyl isocyanate) (MDI) and 1,4‐butanediol (BDO) based monodisperse hard segments (HSs), consisting of exactly two to four MDI units extended by BDO, were investigated. Using FT‐IR spectroscopy, increased hydrogen bonded C?O fraction was observed in model TPUs as the HS size increased. The hydrogen bonded C?O fraction was higher in PIB based TPUs compared with PTMO based TPUs, indicating higher phase separation in PIB based TPUs. The morphology of TPUs was investigated using AFM phase imaging, which showed ribbon‐like or interconnected hard domains in PTMO based model TPUs and randomly dispersed hard domains in PIB based model TPUs. SAXS revealed that the degree of phase separation in the model TPUs was higher than in their polydisperse analogues. Domain spacing as well as interfacial thickness increased with the increasing HS size, and both values were higher in PTMO based TPUs. The tensile analysis indicated that model TPUs exhibited higher modulus and slightly higher elongation compared with their polydisperse analogues. Only in PTMO based model TPUs, strain induced crystallization was observed above 300% elongation. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2485–2493     

环氧乙烷-四氢呋喃共聚醚基热塑性聚氨酯弹性体氢键体系的定量研究

氢键为热塑性聚氨酯弹性体内的重要键合力特征。该文基于氢键所引起基团的频移,以FTIR为主要的研究手段,并结合通过动态力学性能（DMA）研究所建立的评估硬段与软段之间混溶的定量方程,对所合成的以环氧乙烷－四氢呋喃无规共聚醚、2,4－甲苯二异氰酸酯以及1,4－丁二醇为原料的热塑性聚醚聚氨酯弹性体的氢键体系进行了定量化研究。结果表明,大约有30％的硬段混溶进入炊段相对软段的醚氧产生氢键作用,主要的氢键包括硬段羰基与硬段氨基之间的氢键以及硬段烷氧与硬段氨基之间的氢键,仍发生在硬段岛区内。     

Motional heterogeneity and phase separation of functionalized polyester polyurethanes

The polyester polyurethanes, PU based on isophoronediisocyanate, polycaprolactone, and 1,4-butanediol with different amounts of functional groups introduced into the hard segments via second chain extender, 2,2′-bis-(hydroxymethyl) propionic acid, were investigated by electron spin resonance, ESR, spin label method, wide-angle X-ray diffraction, WAXD, optical microscopy and differential scanning calorimetry, DSC. The objective of this study is to clarify the effect of functional groups on the motional heterogeneity, microphase separation and crystallisation of the polyurethanes. The concentration of carboxylic groups varied from 0 to 0.45 mmol g⁻¹. The temperature-dependent ESR spectra of spin labelled PU hard segments chain ends with stable nitroxide radical 2,2,6,6-tetramethyl-4-aminopiperidin-1-yloxyl are sensitive to the amount of functional groups attached to the hard segments. Composite ESR spectra of functionalized PU, with fast and slow component, suggest that PU hard segments are partitioned in two motionally different environments. According to the ratio of fast and slow component motional heterogeneity increases with an increase of functional groups up to 0.35 mmol g⁻¹ and above this concentration slow component decreases indicating higher degree of phase mixing and stronger effect of soft segments. Polarized micrographs and the extent of ordering from WAXD measurements reveal the changes of phase morphology with the carboxylic groups content in a similar way as shown from the motional behaviour of spin label on the segmental level. The degree of crystallinity and the separation of spherulitic rings are decreasing above a certain concentration of functional groups. The effect of functional groups in PU on the hard and soft segment mixing is discussed in terms of additional noncovalent interactions and chain structure which at critical level of interactions lead to a formation of more open hard segment structure accessible to interaction with the soft segment.     

New type of thermoplastic multiblock elastomers––poly(ester-block-amide)s––based on oligoamide 12 and oligoester prepared from dimerized fatty acid

Multiblock poly(ester-block-amide)s (PEA) elastomers comprising hard blocks of oligoamide and oligoester soft segments were prepared and their structure-property relations were analysed. The polycondensation reaction of oligoesters (prepared from 1,4-butanediol and dimerized fatty acid) with oligolaurolactam (PA12) gave copolymer series with variable blocks content (the soft segments content was varied from 24 to 60 wt.%). PEAs are the phase system composed of crystallised sequences of oligoamide (hard segment phase) as well as oligoesters (soft segment phase). Mixing between the hard and soft phases was studied by thermal and mechanical measurements (DSC, DMTA). These results have indicated on a multiphase structure of investigated materials. The relationship between the observed thermal and tensile properties and the soft/hard segments content indicated on an increase of the phase separation with soft segments content.     

Studies on thermoplastic polyurethanes based on new diphenylethane-derivative diols. II. Synthesis and characterization of segmented polyurethanes from HDI and MDI

Various new thermoplastic segmented polyurethanes were synthesized by a one-step melt polymerization from aliphatic-aromatic α,ω-diols containing sulfur in the aliphatic chain, including 4,4′-(ethane-1,2-diyl)bis(benzenethioethanol), 4,4′-(ethane-1,2-diyl)bis(benzenethiopropanol) and 4,4′-(ethane-1,2-diyl)bis(benzenethiodecanol) as chain extenders, hexane-1,6-diyl diisocyanate (HDI) or 4,4′-diphenylmethane diisocyanate (MDI) and 20-80 mol% poly(oxytetramethylene)diol (PTMO) with molecular weight of 1000 g/mol as a soft segment. The reaction was conducted at the molar ratio of NCO/OH = 1 and 1.05, and in the case of the HDI-based polyurethanes in the presence of dibutyltin dilaurate as a catalyst. The effect of the diisocyanate used on the structure and some physicochemical, thermal and mechanical properties of the segmented polyurethanes were studied. The structures of these polyurethanes were examined by FTIR and X-ray diffraction analysis. The thermal properties were investigated by differential scanning calorimetry and thermogravimetric analysis. Shore hardness and tensile properties were also determined. All the synthesized polymers showed partially crystalline structures. The MDI-based polyurethanes were products with lower crystallinity, higher glass-transition temperature (T_g) and better thermal stability in comparison with the HDI-based ones. The MDI series polymers also exhibited higher tensile strength (up to ∼36 MPa vs. ∼23 MPa) and elongation at break (up to ∼3900% vs. ∼900%), but lower hardness than the analogous HDI series polyurethanes. In both series of the polymers an increase in PTMO soft-segment content was associated with decreased crystallinity, T_g, hardness and tensile strength. An increase in PTMO content also involved an increase in elongation at break.     

Synthesis and characterization of polydimethylsiloxane polyurea-urethanes and related zwitterionomers

A series of segmented polyurea urethane and polyurea block copolymers based on a hexane diisocyanate (HDI) modified aminopropyl terminated polydimethylsiloxane soft segment was synthesized. The hard segments consisted of 4,4′-methylene diphenylene diisocyanate (MDI) which was chain extended with 1,4-butanediol (BD), N-methyldiethanolamine (MDEA), or ethylene diamine. Zwitterionomers were prepared by quaternizing the tertiary amine of the MDEA extended material with γ-propane sultone. The effect of chemical structure on the extent of phase separation and physical properties was studied using a variety of techniques including thermal analysis, dynamic mechanical spectroscopy, tensile testing, and small-angle x-ray scattering. It was observed that the compatibility between the nonpolar polydimethylsiloxane soft segments and the polar urethane hard segments was improved by inserting HDI linkages into the polydimethylsiloxane soft segments. The aggregation of hard segments was enhanced by increasing hard-segment content or by the introduction of ionic functionality. The tensile strength and modulus of these materials was higher than those of polyurethanes containing soft segments based on polydimethylsiloxane and its derivatives.     

Pi‐conjugated chain extenders for the synthesis of optoelectronic segmented polyurethanes

The optical properties of mechanochromic materials change under mechanical stress. Segmented polyurethanes are elastomers composed of amorphous, saturated chain soft segments, and rigid pi‐conjugated hard domains. Within aggregates of hard domains pi–pi interactions may form and result in perturbation of the optoelectronic properties of the system. Disruption and restoration of these electronic interactions within the material may lead to observable mechanochromic response. A series of oligothiophene diols and diamines, as well as a naphthalene diimide diol, have been synthesized for incorporation into the hard domains of segmented polyurethanes and polyureas using long poly(tetramethylene oxide) chains as soft segments. The resulting polymers were evaluated to determine their extent of polymerization and their thermal stability. The optical properties of the materials were studied in solution and as thin films. Where possible the electrochemical properties of the polymers were also explored. The length of the soft segment chains in the segmented polyurethanes hindered electronic coupling of hard domains. Future work involving smaller, more solubilizing soft segments may allow for easier material characterization and mechanochromic response. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Polycaprolactone based biodegradable polyurethanes

Two series of segmented polyurethanes were prepared with systematic variation in soft and hard segment length. The soft segment was constituted by polycaprolactone (PCL) blocks of molecular masses 530 or 2000 and the hard segment (HS) by urethane blocks, in a concentration that varied from 12% to 44% in weight of the whole polyurethane. Morphological analyses indicated that the amount of crystallinity of copolymers was strongly dependent on the PCL molar mass and hard segment content. The copolymers with longer PCL soft segments (Mn=2000) were semicrystalline, but those with shorter PCL segment (Mn=530) were unable to crystallize. The primary factor affectingthe biodegradability of copolymers as evaluated by Sturm tests was the extent of the phase separation, and that the segmental blending of the less biodegradable polyurethane (HS) blocks with PCL in the amorphous phase had a critical unfavorable consequence, which may be attributed to the size of the accessible area by microorganisms.     

The effect of thiolation on the mechanical and protein adsorption properties of polyurethanes

Segmented polyurethanes are important polymers for a number of industrial and technological applications. The purpose of this work was to synthesize polybutadiene-based polyurethanes and subsequently graft carboxylate and sulfonate side chains via thiol-ene reaction. Spectroscopic investigations showed that grafting yielded good conversion for the vinyl unsaturation of the polybutadiene soft segment. DSC and tensile testing revealed that grafted polyurethanes had a better segmental compatibility and superior mechanical properties than the control polyurethane without grafting. The carboxylic side chains of the soft segment were responsible for the observed improved mechanical properties. Initial protein adsorption tests on these polymers were found to be higher than the control surface. The polyurethanes of the current study could be used for biomedical applications where protein attachment to the surface is needed for specific cell adhesion and tissue repair.     

聚氨酯硬链段球晶生长与软硬链锻混容性的关系

线型可溶性聚氨酯的硬链段结晶难以长成球晶 ,然而本实验室已经证明即使从熔体结晶硬链段也是能够长成球晶的 .研究了聚酯与聚醚型聚氨酯硬链段长球晶的规律 ,并发现聚氨酯硬链段长球晶的难易与聚氨酯软硬链段混容性密切相关 .动态力学分析 (DMA)与示差扫描量热 (DSC)实验表明聚ε 已内酯 (PCL)、聚已二酸丁二醇酯 (PTMA)、聚四氢呋喃 (PTMO)及聚环氧丙烷 (PPO)型聚氨酯的软硬链段混容性从前至后递减 .从熔体退火结晶时 ,聚氨酯硬链段长成球晶的退火温度范围是有限的 ,软硬链段混容性越好 ,聚氨酯硬链段能长成球晶的温度范围越窄 ,所需长的时间越长 .聚氨酯硬链段长球晶的下限温度取决于软硬链段间所存在的氢键作用 ,聚氨酯硬链段长球晶的上限温度与软硬链段混容性直接相关 .     

Effect of Soft Segment Molecular Weight and 3-Methyl Side Group on Microstructural Separation in Polyurethane Elastomers

Abstract

The object of this study was to assess the effect of the chain length and of the pendant 3-methyl side group in the soft segment of polyurethane (PU) elastomers. In addition, the effect of annealing-quenching on the degree of microstructural segregation between the hard and soft segments was also investigated. The study employed electron spin resonance (ESR), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). Samples for ESR measurements were spin-labeled with the nitroxide probe, 4-hydroxy-2,2′,6,6′-piperidine-1-oxyl (TEMPOL), by reaction of an isocyanate group with the hydroxyl group of TEMPOL. The nitroxide label is therefore located at a chain end. The PU's were based on 4,4′-diphenylmethane diisocyanate (MDI), poly(oxytetramethylene) glycols (PTMO), and hydroxyl-terminated random copolymers of tetrahydrofuran and 3-methyl-tetrahydrofuran (THF/Me-THF). Purified 1,4-butanediol (BD) was used as a chain extender. The elastomers made from higher molecular weight (MW) soft segments have better phase segregation than their lower MW counterparts. The 3-methyl side groups on the PTMO backbone have some effect on the arrangements of the two domains. ESR analysis indicated that the increase in the MW of THF/Me-THF decreased the degree of mixing between the hard and soft segments. In PU elastomers made from high MW soft segments, the presence of crystallinity was observed from the DSC measurements. The crystallinity of the soft segments was disrupted by the existence of the 3-methyl side groups.     

不同软段结构的双离子型聚氨酯离聚体

本文讨论了以聚环氧乙烷(PEO)、聚环氧丙烷(PPO)以及聚丁二烯(PBD)为软段,以4,4’-二异氰酸二苯甲烷(MDI)和N,N-二羟乙基甲胺(MDEA)为硬段的链段型聚氨酯的合成。并通过MDEA中的第三胺与Υ-丙磺内酯反应,转化为双离子型离聚体。用差示扫描量热、红外光谱、动态力学性能以及应力-应变等实验方法研究了化学组成和氨磺化程度对材料相分离程度,力学性能和形态结构的影响。结果表明,离子化后的材料力学性能有很大的改善。对PBD为软段的材料,离子化只能提高硬段“微区”的内聚能,而对PEO、PPO为软段的材料,还能大大提高软、硬相的相分离程度。