Spectrophotometric determination of nitrite in natural waters using diazotization-coupling method with column preconcentration on naphthalene supported with ion-pair of tetradecyldimethylbenzyl-ammonium and iodide

A column preconcentration method has been established for the spectrophotometric determination of traces of nitrite using diazotization and coupling on an naphthalene-tetradecyldimethylbenzylammonium (TDBA)-iodide (I) adsorbent. Nitrite ion reacts with sulfanilic acid (SA) in the pH range 1.8–3.0 for the SA-1-naphthol system and in the pH range 2.3–3.2 for the SA-1-naphthylamine-4-sulfonate system (SA-NAS system) in hydrochloric acid medium to form water-soluble colourless diazonium cations. These cations were coupled with 1-naphthol in the pH range 1.6–4.6 and with NAS in the pH range 2.6–5.0 to be retained on naphthalene-TDBA-I packed in a column. The solid mass was dissolved from the column with 5 mL of dimethylformamide (DMF) and the absorbance measured at 418 nm for the SA-1-naphthol system and at 485 nm for the SA-NAS system. The calibration curve was linear over the concentration range 0.02–0.87 mg/L for SA-1-naphthol and 0.02–0.80 mg/L in the sample for SA-NAS. The molar absorptivity was calculated to be 1.70 × l0⁴ Lmol⁻¹ cm⁻¹ for SA-1-naphthol and 1.66 × l0⁴ L mol⁻¹ cm⁻¹ for SA-NAS. The detection limits were found to be 0.014 and 0.016 mg/L for SA-1-naphthol and SA-NAS, respectively. The preconcentration factors were 8 and 6 for SA-1-naphthol and SA-NAS, respectively. Replicate determinations of seven sample solutions containing 6.6 ug of nitrite for SA-1-naphthol and 5.3 ug of nitrite for SA-NAS gave mean absorbances of 0.486 and 0.382 with relative standard deviations of 0.49 and 0.58%, respectively. Interferences due to various foreign ions have been studied and the method has been applied to the determination of 27–65 μg/L levels of nitrite in natural waters. The recovery and relative standard deviation for water samples were 98–102% and 0.49–0.58% for both systems. Presented at the 29th Colloquium Spectroscopicum Internationale, Leipzig, Germany, 27 August –1 September 1995     

Evaluation of on-line coupling size exclusion chromatography electrothermal atomic absorption spectrometry for selenium speciation

 Chromatographic effluents were on-line analyzed by Zeeman-ETAAS, using a flow-through cell placed in a graphite furnace autosampler as interface. To obtain high sampling rates, the use of fast graphite furnace programmes was studied. Conventional programmes of 96 s were reduced to 18 s by using hot injection (120 °C) and reducing the charring step to 2 s. The increase of the injection volume from 20 to 60 μl lengthened the programme to 46 s. Nickel had to be added to get a comparable response for both inorganic and organic selenium species (selenite and selenomethionine) and to reduce the interferent effect produced in presence of the chromatographic eluent (TRIS 0.01 mol l^-1, NH₄NO₃ 0.1 mol l^-1, pH 7). The optimized conditions were applied to the speciation of selenium in human erythrocyte lysates by size exclusion LC-ETAAS. Using a high performance size exclusion column selenium could be assigned to proteins of 100 and 35 kDa. Detection limits in the range of 1 ng (2 μg l^-1 for 500 μl injection volume) were obtained for the combined technique. Received: 9 October 1996/Revised: 8 July 1996/Accepted: 14 July 1996     

Simultaneous separation and microdetermination of cobalt(II), nickel(II) and copper(II)

 A sensitive and selective flotation procedure for the separation of microamounts of Co(II), Ni(II) and Cu(II) separately or in admixture is described. The maximum separation rate (∼1) for 0.1 mmol/L of each analyte is achieved using 1 mmol/L of both oleic acid (HOL) surfactant and 4-phenylthiosemicarbazide (HPTS) as a collector in the pH range 6–7. A method for the simultaneous separation and microdetermination of the analytes is elaborated, based on adding excess HPTS and floating the species with HOL at pH ∼6. The filtrate (which is clear brownish-yellow) obtained from the scum is used for the spectrophotometric determination of Co(II) at 350 nm. The formation constants of 1:1 and 1:2 [Co(II):HPTS] species are 6.9×10⁵ and 1.22×10¹⁰ L mol^-1, respectively. Beer’s law is obeyed up to 9 μg/mL of Co(II) with a molar absorptivity of 1.15×10⁴ L mol^-1 cm^-1. The precipitate in the scum layer is quantitatively collected, dissolved in aqua regia and aspirated directly into the flame for the (AAS) determination of Ni and Cu. The procedure is successfully applied to some natural water samples. A mechanism for the separation of the analytes is proposed. Received: 23 January 1996/Revised: 1 April 1996/Accepted: 9 April 1996     

Sorption-Catalytic Determination of Imazapyr on a Copper-Containing Sorbent

 Sorption of copper on filter-paper with chemically attached hexamethylenediamino-groups (HMDA-filter) allows to obtain the sorbent (Cu/HMDA-filter) stable in respect to desorption of copper. A nitrogen-containing herbicide imazapyr (imaz) is retained on Cu/HMDA-filters at pH 5.5–7.0 forming a relatively stable complex. Imazapyr is determined directly on the sorbent by its activating effect in the oxidation of hydroquinone with H₂O₂ catalyzed by Cu(II) with the formation of a product absorbing at 490 nm. The copper ions serve both to preconcentrate imazapyr and to catalyze the indicator reaction. The use of 1-μL sample aliquots pipetted onto the Cu/HMDA-filters allows to determine 1 × 10⁻³–0.03 μmol of imazapyr, whereas preconcentration of the analyte by pumping of its solution through the same sorbent expands the linear range to 1 × 10⁻⁴–1 × 10⁻¹ μmol of imazapyr. When the indicator reaction is carried out in solution, the range of activating action of imazapyr is narrower (0.06–0.1 μmol a for a solution volume of 10 mL). The determination is selective: 5–100-fold amounts of amines, aminoacids, carboxylic acid derivatives and other model compounds do not interfere. Soil extracts and carrot juice samples spiked with imazapyr have been analyzed. Received January 10, 2000. Revision July 28, 2000.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Determination of cyanide in blood by electrospray ionization tandem mass spectrometry after direct injection of dicyanogold

An electrospray ionization tandem mass spectrometric (ESI-MS-MS) method has been developed for the determination of cyanide (CN^–) in blood. Five microliters of blood was hemolyzed with 50 μL of water, then 5 μL of 1 M tetramethylammonium hydroxide solution was added to raise the pH of the hemolysate and to liberate CN^– from methemoglobin. CN^– was then reacted with NaAuCl₄ to produce dicyanogold, Au(CN)₂^–, that was extracted with 75 μL of methyl isobutyl ketone. Ten microliters of the extract was injected directly into an ESI-MS-MS instrument and quantification of CN^– was performed by selected reaction monitoring of the product ion CN^– at m/z 26, derived from the precursor ion Au(CN)₂^– at m/z 249. CN^– could be measured in the quantification range of 2.60 to 260 μg/L with the limit of detection at 0.56 μg/L in blood. This method was applied to the analysis of clinical samples and the concentrations of CN^– in the blood were as follows: 7.13 ± 2.41 μg/L for six healthy non-smokers, 3.08 ± 1.12 μg/L for six CO gas victims, 730 ± 867 μg for 21 house fire victims, and 3,030 ± 97 μg/L for a victim who ingested NaCN. The increase of CN^– in the blood of a victim who ingested NaN₃ was confirmed using MS-MS for the first time, and the concentrations of CN^– in the blood, gastric content and urine were 78.5 ± 5.5, 11.8 ± 0.5, and 11.4 ± 0.8 μg/L, respectively.     

Determination of palladium by adsorptive stripping voltammetry

 Adsorptive accumulation of the Pd(II) complex with dimethylglyoxime was evaluated for stripping voltammetry with respect to different parameters. The sensitivity of the method and the linearity between the peak current and the concentration of Pd(II) depends on the ionic strength, the electrode area, the preconcentration time, the transport rate to the electrode, and the potential scan rate. The most appropriate medium was 0.1 mol/L acetate buffer between pH 3.5 and 4. Using 2 min of preconcentration at a 2.6 mm² electrode and the differential pulse mode, a detection limit of 0.05 μg/L Pd was achieved for liquid samples and 50 ng/g for solid samples. Different aqueous and solid samples were analysed and the recovery from biological and inorganic materials investigated. Received: 29 February 1996/Revised: 29 July 1996/Accepted: 1 August 1996     

Design of a field flow system for the on-line spectrophotometric determination of phosphate, nitrite and nitrate in natural water and wastewater

This study describes the design and optimisation of a field flow system for the in-situ collection and on-line determination of phosphate, nitrate and nitrite by flow injection analysis-spectrophotometry. The method is based on the initial determination of phosphate as its phosphoantimonylmolybdenum blue complex which is then oxidized on-line by nitrite and the decrease in absorbance is monitored at 880 nm. Nitrate is determined as the difference between total and initial nitrite content in a separate flow after reduction to nitrite in a cadmium reductive column. The calibration curves were linear in the range 0–2.00 mg L⁻¹ P-phosphate, 0–10.00 mg L⁻¹ nitrite and 0–7.00 mg L⁻¹ nitrate with correlation coefficients of 0.9979, 0.9993 and 0.9995, respectively. The detection limits, calculated as 3S/N, were 0.15 mg L⁻¹ for P-phosphate, 0.17 mg L⁻¹ for nitrite and 0.09 mg L⁻¹ for nitrate. The reproducibility was below 3.0% (n = 7). Method validation in the analysis of natural water and wastewater samples revealed that it can efficiently be applied to the determination of the target analytes, with recoveries in the range of 92–108%. Correspondence: Athanasios G. Vlessidis, Laboratory of Analytical Chemistry, Department of Chemistry, University of Ioannina, Ioannina 45110, Greece     

Monosegmented flow-analysis of slow enzymatic reactions: Determination of triglycerides in serum

 A monosegmented flow system (MCFA) is proposed to achieve slow enzymatic spectrophotometric determinations, here applied to the determination of triglycerides in blood serum. The sample (4.5 μL), enzymatic reagent (150 μL) and an air plug (100 μL) are simultaneously inserted into a carrier stream buffered to pH 7.9 (Tris ⋅ HCl). In order to avoid the cumbersome step of air removal, a relocating detector was used. This system handles about 60 samples/h, yielding precise results (r.s.d. usually<2.5%). Sensitivity is 56 mAU ⋅ L/mmol up to 6 mmol/L triglycerides. Accuracy was assessed by running 50 samples already analysed by a conventional procedure yielding the equation C_MCFA(mmol/L)=1.00(±0.04) C_Ref(mmol/L)−0.03(±0.08); r=0.990. Received: 22 January 1997/Revised: 12 March 1997/Accepted: 28 March 1997     

An optosensor for tryptophan with C18 silica gel as a substrate

 A flow-through optosensor for tryptophan with C18 silica gel as a substrate is proposed. It has been developed in conjunction with a flow-injection analysis system and is based on the retention of tryptophan on the C18 column and the enhancement of its fluorescence. The detection limit is 25 ng mL^-1 with a relative standard deviation of 2.9% for 7 determinations of 10 μg mL^-1 of tryptophan. Most of the common species do not interfere. The method has been successfully applied to a pharmaceutical preparation. Received: 8 July 1996/Revised: 26 September 1996/Accepted: 30 September 1996     

Determination of mercury(II) traces in drinking water by inhibition of an urease reactor in a flow injection analysis (FIA) system

 The integration of an urease reactor into a gas diffusion flow injection system was investigated for the determination of urease inhibitors. The enzyme was immobilized by entrapping in polyacrylamide gel. Besides copper and silver ions mercury ions inhibit the conversion of urea to carbon dioxide and ammonia catalysed by urease. The pH change of the carrier solution caused by the ammonia released was measured potentiometrically with a pH electrode. The inhibition behaviour of Hg(II) ions was investigated. A linear range from 2 to 20 μg L^-1 Hg(II) was obtained after a 90 s inhibition, with a correlation coefficient of r=0.9997. The relative standard deviation was 1.4% for five measurements of 2 μg L^-1Hg(II). A sample frequency of 7 h^-1 was achieved. The inhibited enzyme can be reactivated. The method was applied to the determination of Hg(II) in two drinking water samples. Received: 16 April 1996/Revised: 3 June 1996/Accepted: 11 June 1996     

Solid-phase spectrophotometric microdetermination of iron with ascorbic acid and ferrozine

 A very sensitive and selective method for the determination of trace amounts of iron has been developed, based on the reduction of Fe(III) to Fe(II) by ascorbic acid, followed by chromogenic chelation of Fe(II) with ferrozine. The complex Fe(II)-ferrozine is easily sorbed on a dextran-type anion-exchange gel packed in a 1 mm cell, and the absorbance of the gel is measured directly at 569 and 800 nm. The extended linear range of the determination is 0.5–10 ng ml^-1 of iron (apparent molar absorptivity=4.4×10⁷ l mol^-1 cm^-1) and the precision (RSD) 1.3% for a concentration of 5 ng ml^-1 of iron (n=10). The detection limit for a sample volume of 1000 ml, using 0.040 g of anion-exchanger, corresponds to 0.12 ng ml^-1. The method has been successfully applied to the determination of iron in natural and waste waters, wine, soil extract and previously digested vegetal tissues, drugs and human hair. Received: 20 November 1995/Revised: 23 January 1996/Accepted: 26 January 1996     

Determination of traces of uranium and thorium in (Ba, Sr) TiO3 ferroelectrics by inductively coupled plasma mass spectrometry

 Traces of uranium and thorium in barium(II), strontium(II) titanate ((Ba, Sr)TiO₃) ferroelectric materials were determined by inductively coupled plasma mass spectrometry (ICP-MS). Samples were completely dissolved by a mixture of 1.4% H₂O₂ and 1.0 mol⋅l^-1 HNO₃. For a complete separation of the analytes from the matrix elements, a two step separation technique involving leaching and anion-exchange was applied. By the leaching step with HNO₃ more than 90% of the matrix can be removed whereas the analytes completely remained in the solution. The anion-exchange step was carried out on a BIO⋅RAD AG1-X8 column with a mixture of 1.0 mol⋅l^-1 HF and 0.5 mol⋅l^-1 HNO₃ as eluent. The content of uranium and thorium was subsequently measured by ICP-MS. The detection limits (D.L.) obtained were 0.043 ng g^-1 and 0.035 ng g^-1 for U and Th, respectively. The reproducibility was satisfactory with a relative standard deviation of less than 3% (at the 1 ng g^-1 level, n=5). The matrix concentrations in the final solution were reduced to the sub-μg ml^-1 level which is in the range of the detection limits of USN-ICP-AES (ultrasonic nebulization-ICP-atomic emission spectroscopy). The method was successfully applied to the determination of uranium and thorium in three synthetic (Ba, Sr)TiO₃ samples spiked with the analytes at levels of 1, 5 and 10 ng g^-1 and three (Ba, Sr)TiO₃ ferroelectric samples containing sub-ng g^-1 levels of the analytes. Received: 26 February 1996/Revised: 28 May 1996/Accepted: 5 June 1996     

Anionic cartridge preconcentrators for inorganic arsenic, monomethylarsonate and dimethylarsinate determination by on-line HPLC-HG-AAS

 Preconcentration anionic cartridges in combination with hyphenated FI-HG-AAS and HPLC-HG-AAS have been evaluated for the preconcentration and quantification of total toxic arsenic and of inorganic arsenic, monomethylarsonate and dimethylarsinate species, respectively. Optimum retention and elution parameters of the species on the anionic cartridges are evaluated and the quality parameters of the analysis are reported. The detection limits for the arsenic species under study range from 0.1 μg L^-1 to 0.6 μg L^-1. The proposed method was successfully applied to the determination of arsenic species in spiked fresh water. Received: 2 April 1996/Revised: 22 July 1996/Accepted: 25 July 1996     

Determination of traces of uranium and thorium in (Ba, Sr) TiO3 ferroelectrics by inductively coupled plasma mass spectrometry

 Traces of uranium and thorium in barium(II), strontium(II) titanate ((Ba, Sr)TiO₃) ferroelectric materials were determined by inductively coupled plasma mass spectrometry (ICP-MS). Samples were completely dissolved by a mixture of 1.4% H₂O₂ and 1.0 mol⋅l^-1 HNO₃. For a complete separation of the analytes from the matrix elements, a two step separation technique involving leaching and anion-exchange was applied. By the leaching step with HNO₃ more than 90% of the matrix can be removed whereas the analytes completely remained in the solution. The anion-exchange step was carried out on a BIO⋅RAD AG1-X8 column with a mixture of 1.0 mol⋅l^-1 HF and 0.5 mol⋅l^-1 HNO₃ as eluent. The content of uranium and thorium was subsequently measured by ICP-MS. The detection limits (D.L.) obtained were 0.043 ng g^-1 and 0.035 ng g^-1 for U and Th, respectively. The reproducibility was satisfactory with a relative standard deviation of less than 3% (at the 1 ng g^-1 level, n=5). The matrix concentrations in the final solution were reduced to the sub-μg ml^-1 level which is in the range of the detection limits of USN-ICP-AES (ultrasonic nebulization-ICP-atomic emission spectroscopy). The method was successfully applied to the determination of uranium and thorium in three synthetic (Ba, Sr)TiO₃ samples spiked with the analytes at levels of 1, 5 and 10 ng g^-1 and three (Ba, Sr)TiO₃ ferroelectric samples containing sub-ng g^-1 levels of the analytes. Received: 26 February 1996/Revised: 28 May 1996/Accepted: 5 June 1996     

HPLC determination of collectors used for the flotation of heavy metal minerals

 A reversed-phase HPLC-method for the separation of mixtures of collectors for the flotation of heavy metal minerals is described. It is based on a Nucleosil 5C18 column, isocratic elution and UV-detection at 238 nm. The mobile phase is methanol-water-5% phosphoric acid (40:60:4, v/v). The method is applied to the determination of six collectors in aqueous solutions from flotation processes. The relative standard deviations are 1.6–3.2% in the concentration range 2–10 mg/L. The detection limits are 1 μg/L for 8-hydroxyquinoline, dimethylglyoxime and salicylic acid, 2 μg/L for salicylhydroxamic acid and 5 μg/L for benzenetriazol and salicylaldoxime, respectively. Received: 19 April 1996/Revised: 14 August 1996/Accepted: 23 August 1996     

Bromide/bromate speciation by NTI-IDMS and ICP-MS coupled with ion exchange chromatography

 Two different mass spectrometric methods, negative thermal ionization isotope dilution mass spectrometry (NTI-IDMS) and inductively coupled plasma mass spectrometry (ICP-MS), off-line and on-line coupled with anion exchange chromatography, have been developed for simultaneous bromide and bromate determinations in water samples. The detection limits of these methods are in the range of 0.03–0.09 μg/L using a 50 mL sample.The results are independent of the content of other anions, which could be demonstrated by the analyses of six mineral waters containing chloride and sulfate of up to 160 mg/L and 1500 mg/L, respectively. Bromide has been analyzed by the NTI-IDMS method in the range of 10–500 μg/L and bromate in the range of 1–50 μg/L with relative standard deviations of 0.3–1.2% and 0.4–6%. Quantification for the ICP-MS method was carried out by the standard addition technique, which resulted in relative standard deviations of 5.5% for bromide at the 500 μg/L level and of 13% for bromate at the level of about 3 μg/L. These results are compared with those described in the literature for ion chromatographic (IC) and other methods and those obtained in this work by IC using UV detection, which allows high concentrations of chloride in the bromate fraction. The detection limits of this IC method are 6 μg/L for bromide and 30 μg/L for bromate. NTI-IDMS and ICP-MS therefore fit the recommendations of the European Union (detection limit<2.5 μg/L; precision and accuracy better than 25% at the 10 μg/L level) for methods analyzing the carcinogenic bromate much better than IC and other methods applied up to now. As a definitive but time consuming method, NTI-IDMS is preferably applicable as a calibration technique, whereas ICP-MS, with relatively short analysis times, due to on-line coupling with chromatography, can be used as a sensitive and powerful routine method for trace bromide and bromate species in water samples. Received: 5 July 1996/Accepted: 7 August 1996     

Bromide/bromate speciation by NTI-IDMS and ICP-MS coupled with ion exchange chromatography

 Two different mass spectrometric methods, negative thermal ionization isotope dilution mass spectrometry (NTI-IDMS) and inductively coupled plasma mass spectrometry (ICP-MS), off-line and on-line coupled with anion exchange chromatography, have been developed for simultaneous bromide and bromate determinations in water samples. The detection limits of these methods are in the range of 0.03–0.09 μg/L using a 50 mL sample.The results are independent of the content of other anions, which could be demonstrated by the analyses of six mineral waters containing chloride and sulfate of up to 160 mg/L and 1500 mg/L, respectively. Bromide has been analyzed by the NTI-IDMS method in the range of 10–500 μg/L and bromate in the range of 1–50 μg/L with relative standard deviations of 0.3–1.2% and 0.4–6%. Quantification for the ICP-MS method was carried out by the standard addition technique, which resulted in relative standard deviations of 5.5% for bromide at the 500 μg/L level and of 13% for bromate at the level of about 3 μg/L. These results are compared with those described in the literature for ion chromatographic (IC) and other methods and those obtained in this work by IC using UV detection, which allows high concentrations of chloride in the bromate fraction. The detection limits of this IC method are 6 μg/L for bromide and 30 μg/L for bromate. NTI-IDMS and ICP-MS therefore fit the recommendations of the European Union (detection limit<2.5 μg/L; precision and accuracy better than 25% at the 10 μg/L level) for methods analyzing the carcinogenic bromate much better than IC and other methods applied up to now. As a definitive but time consuming method, NTI-IDMS is preferably applicable as a calibration technique, whereas ICP-MS, with relatively short analysis times, due to on-line coupling with chromatography, can be used as a sensitive and powerful routine method for trace bromide and bromate species in water samples. Received: 5 July 1996/Accepted: 7 August 1996     

Simultaneous First Derivative Spectrophotometric Determination of Palladium and Nickel Using 2-(2-Thiazolylazo)-5-Dimethylaminobenzoic Acid as an Analytical Reagent

 A simple, rapid, selective, sensitive and economical method has been developed for the simultaneous determination of trace amounts of palladium and nickel in aqueous methanolic medium using 2-(2-thiazolylazo)-5-dimethylam inobenzoic acid as an analytical reagent by first derivative spectrophotometr y. Palladium is determined by measuring base to peak distance at λ=695.0 nm while nickel is estimated by zero crossing method in the mixture. The linearity is maintained between 0.12–1.75 μg mL⁻¹ for palladium and 0.07–1.60 μg mL⁻¹ for nickel in the pH range 2.8–7.2 and 3.4–8.8 respectively. Seven replicate determinations of 1.0 μ g mL⁻¹ of palladium and 0.8 μg mL⁻¹ of nickel in a mixture give a mean signal height of 0.391 for Pd and 0.541 for Ni with relative standard deviations of 0.9% and 1.2%, respectively. The sensitivity of the proposed method is 0.391 (dA/dλ)/(μg mL⁻¹) for palladium and 0.685 (dA/dλ)/(μg mL⁻¹) for nickel. Various parameters have been optimised for the simultaneous determination of palladium and nickel in various complex samples. Received March 30, 1999. Revision November 25, 1999.     

An effective cross-linking of polymer layer on monodisperse, poly(maleic anhydride-styrene)-modified colloidal silica particles and properties of the composite

Summary  The cross-linkings of the surface polymer layer on mono disperse, poly(maleic anhydride-styrene)-modified silica particles by the reaction with diisocyanate were studied. The extent of cross-linking was estimated by the weight decrease by immersing the particles in the buffer solution of pH 2.0, 4.0 and 9.0 at a room temperature for 24 h. The reaction of the polymer-modified silica with 1,6-diisocyanatohexane afforded relatively stable composite particles which lost less than 5 wt% of the polymer in aqueous solution in the pH range 2.0–9.0. The diisocyanate was a preferable cross-linker to 2,4-diisocyanatotoluene in terms of stability in acidic or basic aqueous solution. The flexibility of the cross-linker molecule possibly plays an important role in the cross-linking reaction. The carboxyl and amino groups were formed by treating the cross-linked composite particles with diluted HCl solution; 5–6 and 0.5–1.1 μmol g^-1, respectively. The cross-linked composite particles exhibited the characteristic property of ζ-potential, −44 to −47 mV and −102 to −107 mV in a neutral aqueous solution and ethanol, respectively. Received: 26 May 1997 Accepted: 4 August 1997