Flow-injection analysis for the determination of total inorganic carbon and total organic carbon in water using the H2O2–luminol–uranine chemiluminescent reaction

In the presence of carbonate and uranine, the chemiluminescent intensity from the reaction of luminol with hydrogen peroxide was dramatically enhanced in a basic medium. Based on this fact and coupled with the technique of flow-injection analysis, a highly sensitive method was developed for the determination of carbonate with a wide linear range. The method provided the determination of carbonate with a wide linear range of 1.0 × 10⁻¹⁰–5.0 × 10⁻⁶ mol L⁻¹ and a low detection limit (S/N = 3) of carbonate of 1.2 × 10⁻¹¹ mol L⁻¹. The average relative standard deviation for 1.0 × 10⁻⁹–9.0 × 10⁻⁷ mol L⁻¹ of carbonate was 3.7% (n = 11). Combined with the wet oxidation of potassium persulfate, the method was applied to the simultaneous determination of total inorganic carbon (TIC) and total organic carbon (TOC) in water. The linear ranges for TIC and TOC were 1.2 × 10⁻⁶–6.0 × 10⁻² mg L⁻¹ and 0.08–30 mg L⁻¹ carbon, respectively. Recoveries of 97.4–106.4% for TIC and 96.0–98.5% for TOC were obtained by adding 5 or 50 mg L⁻¹ of carbon to the water samples. The relative standard deviations (RSDs) were 2.6–4.8% for TIC and 4.6–6.6% for TOC (n = 5). The mechanism of the chemiluminescent reaction was also explored and a reasonable explanation about chemical energy transfer from luminol to uranine was proposed. Figure Chemiluminescence profiles in batch system. 1, Injection of 100 μL of K₂CO₃ into 1.0 mL luminol-1.0 mL H₂O₂ solution; 2-3 and 4-5, Injection in sequence of 100 μL of K₂CO₃ and 100 μL of uranine into 1.0 ml luminol-1.0 mL H₂O₂ solution; C_luminol = 1.0 × 10⁻⁷ mol/L, C_H2O2 = 1.0 × 10⁻⁵ mol/L, C_uranine = 1.0 × 10⁻⁵ mol/L, C_K2CO3 = 1.0 × 10⁻⁷ mol/L except for 4-5 where C_K2CO3 = 1.0 × 10⁻⁴ mol/L     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Capillary electrophoretic speciation of Cu(II) and Co(III) in the electroless copper plating baths

Summary A capillary electrophoretic method for the determination of Cu(II) and Co(III) chelates with ethylenediamine in electroless copper plating baths has been developed. The influence of carrier electrolyte parameters such as nature of counter-ion and pH were studied and discussed. The optimised separations were carried out in a fused silica capillary (57 cm × 75 μm I.D.) filled with an ethylenediamine sulfate electrolyte (20 mol L⁻¹ ethylendiamine, pH7.0 with H₂SO₄; applied voltage, +25 kV) using direct UV detection at 214 nm. The detection limits for a signalto-noise ratio of 3 and 10s hydrodynamic injection were 5×10⁻⁶ mol L⁻¹ for Cu(II) and 1×10⁻⁶ mol L⁻¹ for Co(III). The relative standard deviations of the peak areas for Cu(II) and Co(III) were found to be 1.5% and 2.4%, respectively, with five consecutive injections of standard solution containing 5×10⁻⁵ mol L⁻¹ of each metal ion. Application of the method to the speciation of Cu(II) and Co(III) complexes in copper plating bath samples is also demonstrated.     

Voltammetric study of the interaction of the ofloxacin–copper complex with DNA, and its analytical application

The electrochemical behavior of the ofloxacin–copper complex, Cu(II)L₂, at a mercury electrode, and the interaction of DNA with the complex have been investigated. The experiments indicate that the electrode reaction of Cu(II)L₂ is an irreversible surface electrochemical reaction and that the reactant is of adsorbed character. In the presence of DNA, the formation of the electrochemically non-active complexes Cu(II)L₂-DNA, results in the decrease of the peak current of Cu(II)L₂. Based on the electrochemical behavior of the Cu(II)L₂ with DNA, binding by electrostatic interaction is suggested and a new method for determining nucleic acid is proposed. Under the optimum conditions, the decrease of the peak current is in proportional to the concentration of nucleic acids in the range from 3 × 10⁻⁸ to 3 × 10⁻⁶ g · mL⁻¹ for calf thymus DNA, from 1.6 × 10⁻⁸ to 9.0 × 10⁻⁷ g · mL⁻¹ for fish sperm DNA, and from 3.3 × 10⁻⁸ to 5.5 × 10⁻⁷ g · mL⁻¹ for yeast RNA. The detection limits are 3.3 × 10⁻⁹, 6.7 × 10⁻⁹ and 8.0 × 10⁻⁹ g · mL⁻¹, respectively. The method exhibits good recovery and high sensitivity in synthetic samples and in real samples.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Determination of metformin based on amplification of its voltammetric response by a combination of molecular wire and carbon nanotubes

Molecular wires containing copper(II) (CuMW), in the form of the coordination polymer (Cu(II)₄(bpp)₄(maa)₈(H₂O)₂).2H₂O (bpp=1,3-bis(4-pyridyl)propane, maa=2-methylacrylic acid), and multiwalled carbon nanotubes (CNT) have been combined to prepare a paste electrode (CuMW/CNT/PE). The voltammetric response of the CuMW/CNT/PE to metformin (MET) was significantly greater than that of electrodes prepared from other materials, because of both the surface effect of CuMW and CNT and coordination of MET with the Cu(II) ion in the CuMW. A novel voltammetric method for determination of MET is proposed. In pH 7.2 Britton–Robinson buffer, using single sweep voltammetry, the second-order derivative peak current for oxidation of MET at 0.97 V (relative to SCE) increased linearly with MET concentration in the range 9.0 × 10⁻⁷–5.0 × 10⁻⁵ mol L⁻¹ and the detection limit was 6.5 × 10⁻⁷ mol L⁻¹. Figure When a combination of molecular wires containing copper(II) (CuMW) and multiwalled carbon nanotubes (CNT) was used to prepare a paste electrode (CuMW/CNT/PE) the voltammetric response to metformin (curve c) was significantly higher than that at a carbon/PE (curve a) or a CNT/PE (curve b), because of the amplification effect of CNT and CuMW. A novel voltammetric method is proposed for determination of MET     

Flavonol Derivatives for Determination of Cr(III) and W(VI)

 Simple, rapid, sensitive and selective methods for the determination of Cr(III) and W(VI) with flavonol derivatives in the presence of surface-active agents are proposed. In the pH ranges 3.4–4.2 and 1.9–2.5, the molar absorptivities of Cr(III)-morin-emulsifier S (EFA) and W(VI)-morin-polyvinylpyrrolidone (PVP) systems are 1.13×10⁵ and 2.13×10⁴ L mol⁻¹ cm⁻¹ at 435 and 415 nm, respectively. The Cr(III)-quercetin-PVP and W(VI)-quercetin-cetylpyridinium bromide (CPB) systems are formed in the pH ranges 4–4.6 and 2.2–2.8 with molar absorptivities 1.02×10⁵ and 9.02×10⁴ L. mol⁻¹ cm⁻¹ at 441 and 419 nm, respectively. The linear dynamic ranges for the determination of Cr(III) and W(VI) with morin in the presence of EFA and PVP are 0.03–0.46 and 0.71–8.1 μg mL⁻¹, respectively. The corresponding ranges with quercetin are 0.04–0.54 and 0.14–2.1 μg mL⁻¹ of Cr(III) and W(VI), respectively. The r.s.d (n = 10) for the determination of 0.25 and 3.7 μg mL⁻¹ of Cr(III) and W(VI) with morin and their detection limits are 0.88 and 0.99% and 0.016 and 0.63 μg mL⁻¹, respectively. Using quercetin, the r.s.d (n = 10) for 0.22 and 1.2 μg mL⁻¹ of Cr(III) and W(VI) and their detection limits are 0.92 and 0.91% and 0.015 and 0.08 μg mL⁻¹, respectively. The critical evaluation of the proposed methods is performed by statistical analysis of the experimental data. The proposed methods are applied to determine Cr in steel, non-ferrous alloys, wastewater and mud filtrate and to the determination of W in steel. Received March 8, 1999. Revision January 21, 2000.     

Fluorimetric determination of traces of europium(III) using a new chelator and acetate or phosphate in dimethylsulfoxide as enhancers

A new Schiff-base ligand [N, N′, N″-Tri- (2,4-dihydroxyacetophenone) – triaminotriethylamine (TDATA)] with a tripodal structure was synthesized. Its fluorescence intensity with the europium(III) complex was increased about 178-fold in the presence of sodium acetate (NaAc) and about 126-fold in the presence of sodium phosphate (Na₃PO₄) solution. After adding the organic solvent dimethylsulfoxide (DMSO) to the above system, which leads to Eu³⁺ the fluorescence was further enhanced about 12-fold. Spectrofluorimetric determination of trace amounts of Eu³⁺ based on the phenomenon was performed. The excitation and emission wavelength is 365 nm and 615 nm, respectively. Under optimum conditions, the fluorescence intensities vary linearly with the concentration of Eu³⁺ in the range of 4.9 × 10⁻¹²–3.2 × 10⁻⁶ mol · L⁻¹ with a detection limit of 4.5 × 10⁻¹² mol · L⁻¹ (for the TDATA-NaAc-DMSO system) or 6.2 × 10⁻¹¹–8.6 × 10⁻⁶ mol · L⁻¹ with a detection limit of 6.0 × 10⁻¹¹ mol · L⁻¹ (for the TDATA-Na₃PO₄-DMSO system). Interferences of some rare earth metals and other inorganic ions are described. The method is a selective, sensitive, rapid and simple analytical procedure for the determination of europium(III) in a high purity yttrium oxide and synthetic sample. The mechanism for the fluorescence enhancement is also discussed.     

A New Differential Pulse Voltammetric Method for the Determination of Nitrate at a Copper Plated Glassy Carbon Electrode

 A differential pulse voltammetric method for the determination of nitrate has been described, which is applicable to the analysis of natural water samples with nitrate levels greater than 2.8 × 10⁻⁶ M. A reduction peak for the nitrate ions at a freshly copper plated glassy carbon electrode was observed at about −0.50 V vs Ag ∣AgCl∣KCl_satd electrode in a solution of 2.0 × 10⁻² M Cu²⁺, 0.5 M H₂SO₄ and 1.0 × 10⁻³ M KCl and exploited for analytical purposes. The working linear range was established by regression analysis and found to extend from 2.8 ×10⁻⁶ M to 8.0 × 10⁻⁵ M. The proposed method was applied for the determination of nitrate in natural waters. The detection limit of the method was 2.8 × 10⁻⁶ M and the sensitivity was 0.9683 A·L/mol. The possible interferences by some ions such as phosphate, nitrite and some halides were determined and found to lead to shifts of the peak position and increasing the peak heights. Received March 15, 1999. Revision July 9, 1999.     

Voltammetric investigation and amperometric detection of the bisphosphonate drug sodium alendronate using a copper nanoparticles-modified electrode

The electrochemical behavior of sodium alendronate on copper microparticle- and copper nanoparticle-modified carbon paste electrodes was investigated. In the voltammograms recorded using microparticles, a single anodic oxidation peak appeared, while using nanoparticles, two anodic peaks appeared. The anodic currents were related to the electrocatalytic oxidation of alendronate via the active species of Cu(III). The catalytic rate constant for the electrocatalytic oxidation process and the diffusion coefficient of alendronate were obtained to be 1.57 × 10³ cm³ mol⁻¹ s⁻¹ and 2.44 × 10⁻⁶ cm² s⁻¹, respectively. A sensitive and time-saving detection procedure was developed for the analysis of alendronate, and the corresponding analytical parameters were reported. Alendronate was determined with a limit of detection of 11.26 μmol L⁻¹ with a linear range of 50–6,330 μmol L⁻¹. The proposed amperometric method was applied to the analysis of commercial pharmaceutical tablets, and the results were in good agreement with the declared values.     

Catalytic adsorptive stripping voltammetric determination of copper(II) on a carbon paste electrode

A catalytic adsorptive stripping voltammetric method for the determination of copper(II) on a carbon paste electrode (PCE) in an alizarin red S (ARS)-K₂S₂O₈ system is proposed. In this method, copper(II) is effectively enriched by both the formation and adsorption of a copper(II)-ARS complex on the PCE, and is determined by catalytic stripping voltammetry. The catalytic enhancement of the cathodic stripping current of the Cu(II) in the complex results from a redox cycle consisting of electrochemical reduction of Cu(II) ion in the complex and subsequent chemical oxidation of the Cu(II) reduction product by persulfate, which reduces the contamination of the working electrode from Cu deposition and also improves analytical sensitivity. In Britton-Robinson buffer (pH 4.56±0.1) containing 3.6×10⁻⁵ mol L⁻¹ ARS and 1.6×10⁻³ mol L⁻¹ K₂S₂O₈, with 180 s of accumulation at −0.2 V, the second-order derivative peak current of the catalytic stripping wave was proportional to the copper(II) concentration in the range of 8.0×10⁻¹⁰ to ∼3.0×10⁻⁸ mol L⁻¹. The detection limit was 1.6×10⁻¹⁰ mol L⁻¹. The proposed method was evaluated by analyzing copper in water and soil.     

Synthesis,crystal structure,and third-order nonlinear optical properties of a copper(I) one-dimensional coordination polymer [Cu(μ-1,1,1,3-N<Subscript>3</Subscript>)]<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>

A novel copper(I) azide coordination polymer [Cu(μ-1,1,1,3-N₃)] _n has been synthesized by the low-temperature solution-state reaction. Crystal X-ray analyses reveal that compound [Cu(μ-1,1,1,3-N₃)] _n possesses a type of three-dimensional (3D) framework structure. The polymer was characterized by elemental analyses, IR spectra, and UV-Vis spectra. The third-order nonlinear optical (NLO) properties were also investigated, and they exhibit good linear absorption and self-defocusing performance with modulus of the hyperpolarizability (γ) 8.16 × 10⁻³⁰ esu for [Cu(μ-1,1,1,3-N₃)] _n in a 1.96 × 10⁻⁴ mol dm⁻³ DMF solution.     

A new amperometric H<Subscript>2</Subscript>O<Subscript>2</Subscript> biosensor based on nanocomposite films of chitosan–MWNTs,hemoglobin, and silver nanoparticles

A new H₂O₂ biosensor was fabricated on the basis of nanocomposite films of hemoglobin (Hb), silver nanoparticles (AgNPs), and multiwalled carbon nanotubes (MWNTs)–chitosan (Chit) dispersed solution immobilized on glassy carbon electrode (GCE). The immobilized Hb displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ′) of −22.5 mV in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) in the Chit–MWNTs film was evaluated as 2.58 s⁻¹ according to Laviron’s equation. The surface concentration (Γ*) of the electroactive Hb in the Chit–MWNTs film was estimated to be (2.48 ± 0.25) × 10⁻⁹ mol cm⁻². Meanwhile, the Chit–MWNTs/Hb/AgNPs/GCE demonstrated excellently electrocatalytical ability to H₂O₂. Its apparent Michaelis–Menten constant (K _M^app) for H₂O₂ was 0.0032 mM, showing a good affinity. Under optimal conditions, the biosensors could be used for the determination of H₂O₂ ranging from 6.25 × 10⁻⁶ to 9.30 × 10⁻⁵ mol L⁻¹ with a detection limit of 3.47 × 10⁻⁷ mol L⁻¹ (S/N = 3). Furthermore, the biosensor possessed rapid response to H₂O₂ and good stability, selectivity, and reproducibility.     

Spectrofluorimetric determination of trace amounts of coenzyme A using a terbium ion–ciprofloxacin complex probe in the presence of periodic acid

A new spectrofluorimetric method was developed for the determination of trace amounts of coenzyme A (CoA). In the presence of periodic acid (H₅IO₆), CoA can remarkably enhance the fluorescence intensity of the Tb³⁺–ciprofloxacin (CIP) complex at 545 nm in a buffer solution at pH 5.4; the enhanced fluorescence intensity of the Tb³⁺ ion is proportional to the concentration of CoA. The optimal conditions for the determination of CoA were also investigated. The linear range and the detection limit for the determination of CoA were 6.08 × 10⁻⁶–1.64 × 10⁻⁵ and 2.1 × 10⁻⁸ mol L⁻¹, respectively. This method is simple, practical and relatively free of interference from coexisting substances, and can be successfully applied to assess CoA in injection and biological samples. Moreover, the enhancement mechanism of the fluorescence intensity of the CoA–Tb³⁺–CIP system in the presence of H₅IO₆ is also discussed.     

Langmuir–Blodgett film of tetraoxocalix[2]arene[2]triazine modified electrode for voltammetric determination of copper ion

In the present work, a new voltammetric sensor, Langmuir–Blodgett (LB) film of tetraoxocalix[2]arene[2]triazine (TOCT) modified glassy carbon electrode (LB_TOCT-GCE), for trace analysis of copper ion in water samples, was prepared. The morphology of LB_TOCT-GCE was characterized by cyclic voltammetric method, electrochemical impedance spectroscopy, and atomic force microscope. The recognizing mechanism of LB_TOCT-GCE for copper ion in aqueous solution was discussed. Under the optimum experimental conditions, using square wave stripping voltammetry and accumulation time of 300 s, the peak currents were linear relationship with Cu²⁺ concentrations in the range of 2 × 10⁻⁹ to 1 × 10⁻⁶ mol L⁻¹, with detection limit of 1 × 10⁻¹⁰ mol L⁻¹. By this method, real samples (lake water, drinking water, and city wastewater) were analyzed with satisfactory results. In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility, and stability.     

Tetracyanoquinodimethanide adsorbed on a silica gel modified with titanium oxide for electrocatalytic oxidation of hydrazine

The electrocatalytical oxidation of hydrazine at low potential using tetracyanoquinodimethanide adsorbed on silica modified with titanium oxide was investigated by cyclic voltammetry and amperometry. The modified electrode was prepared modifying a carbon paste electrode employing lithium tetracyanoquinodimethanide adsorbed onto silica gel modified with titanium oxide. This electrode showed an excellent catalytic activity and stability for hydrazine oxidation. With this modified electrode, the oxidation potential of hydrazine was shifted toward less positive value, presenting a peak current much higher than those observed on a bare GC electrode. The linear response range, sensitivity and detection limit were, respectively, 2 up to 100 μmol l⁻¹, 0.36 μA l μmol⁻¹, and 0.60 μmol l⁻¹. The repeatability of the modified electrode evaluated in term of relative standard deviation was 4.2% for 10 measurements of 100 μmol l⁻¹ hydrazine solution. The number of electrons involved in hydrazine oxidation (4), the heterogenous electron transfer rate constant (1.08 × 10³ mol⁻¹ l s⁻¹), and diffusion coefficient (5.9 × 10⁻⁶ cm² s⁻¹) were evaluated with a rotating disk electrode.     

Determination of rutin using a CeO2 nanoparticle-modified electrode

CeO₂ nanoparticles approximately 12 nm in size were synthesized and subsequently characterized by XRD, TEM and UV-vis spectroscopy. Then, a gold electrode modified with CeO₂ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified electrode demonstrated strong catalytic effects with high stability towards electrochemical oxidation of rutin. The anodic peak currents (measured by differential pulse voltammetry) increased linearly with the concentration of rutin in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁴ mol · L⁻¹. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol · L⁻¹. The relative standard deviation (RSD) of 8 successive scans was 3.7% for 5.0 × 10⁻⁶ mol · L⁻¹ rutin. The method showed excellent sensitivity and stability, and the determination of rutin in tablets was satisfactory.     

Preconcentration and Voltammetric Determination of the Antihypertensive Doxazosin on a C8 Modified Carbon Paste Electrode

 An electrochemical study of the doxazosin oxidative process at carbon paste electrodes using different voltammetric techniques has been carried out. The process is irreversible and controlled by adsorption, giving rise to an oxidation wave around 1.0 V in citric acid-citrate buffer (pH 3.0). A mechanism based on the oxidation of the amine group is postulated. Two methods based on adsorptive stripping (AdS) of doxazosin at the C₈-modified carbon paste electrode (C₈-MCPE), before its voltammetric determination, are studied, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. By means of AdS-DPV and C₈-MCPE, doxazosin can be determined over the 1.0 × 10⁻⁹ to 3.0 × 10⁻⁸ mol L⁻¹ range with a variation coefficient of 2.2% (2.0 × 10⁻⁸ mol L⁻¹) and a limit of detection of 7.4 ×10⁻¹⁰ mol L⁻¹. If AdS-SWV is used, a linear range from 1.0 × 10⁻⁹ to 4.0 × 10⁻⁸ mol L⁻¹ is obtained, the variation coefficient being 2.8% (2.0 × 10⁻⁸ mol L⁻¹, and the limit of detection reached 7.7 × 10⁻¹⁰ mol L⁻¹. The AdS-DPV procedure was applied to the determination of doxazosin in urine and formulations. Received March 13, 1999. Revision December 23, 1999.     

Simple sensor for simultaneous determination of dihydroxybenzene isomers

A simple sensor based on bare carbon ionic liquid electrode was fabricated for simultaneous determination of dihydroxybenzene isomers in 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0). The oxidation peak potential of hydroquinone was about 0.136 V, catechol was about 0.240 V, and resorcinol 0.632 V by differential pulse voltammetric measurements, which indicated that the dihydroxybenzene isomers could be separated absolutely. The sensor showed wide linear behaviors in the range of 5.0 × 10⁻⁷–2.0 × 10⁻⁴ mol L⁻¹ for hydroquinone and catechol, 3.5 × 10⁻⁶–1.535 × 10⁻⁴ mol L⁻¹ for resorcinol, respectively. And the detection limits of the three dihydroxybenzene isomers were 5.0 × 10⁻⁸, 2.0 × 10⁻⁷, 5.0 × 10⁻⁷ mol L⁻¹, respectively (S/N = 3). The proposed method could be applied to the determination of dihydroxybenzene isomers in artificial wastewater and the recovery was from 93.9% to 104.6%.     

A Novel Enhancing Flow-Injection Chemiluminescence Method for the Determination of Glutathione Using the Reaction of Luminol with Hydrogen Peroxide

 A rapid flow-injection method with chemiluminescence (CL) detection is described for the determination of glutathione (GSH). The method is based on the CL reaction of luminol and hydrogen peroxide. GSH can greatly enhance the chemiluminescence intensity in 0.1 mol/L borax–sodium hydroxide buffer solution (pH = 9.7). The maximum CL intensity was directly proportional to the concentration of GSH in the range 3.0 × 10⁻⁷–2.0 × 10⁻⁵ mol/L, and the detection limit was 6.8 × 10⁻⁸ mol/L. The relative standard deviation was 3.4% for 5.0 × 10⁻⁶ mol/L of GSH (n = 11). Received October 23, 2001; accepted June 18, 2002