An efficient electrochemical disinfection of E. coli and S. aureus in drinking water using ferrocene–PAMAM–multiwalled carbon nanotubes–chitosan nanocomposite modified pyrolytic graphite electrode

This work reported an efficient electrochemical treatment for drinking water disinfection using a pyrolytic graphite electrode modified with ferrocenyl tethered poly(amidoamine) dendrimers–multiwalled carbon nanotubes–chitosan nanocomposite. The influence parameters of electrochemical disinfection of Escherichia coli and Staphylococcus aureus, such as applied potential and sterilization time, were investigated. Further investigation indicated that almost all (99.99 %) of the initial bacteria were killed after applying a low potential of 0.4 V for 10 min. During the electrochemical disinfection process, the oxidized form of ferrocene was formed on electrode, which played a key role in the disinfection towards E. coli and S. aureus. Hence, the proposed method may provide potential application for the disinfection of drinking water.

UPLC-UV-MSE analysis for quantification and identification of major carotenoid and chlorophyll species in algae

A fast method for quantification and identification of carotenoid and chlorophyll species utilizing liquid chromatography coupled with UV detection and mass spectrometry has been demonstrated and validated for the analysis of algae samples. This method allows quantification of targeted pigments and identification of unexpected compounds, providing isomers separation, UV detection, accurate mass measurements, and study of fragment ions for structural elucidation in a single run. This is possible using parallel alternating low- and high-energy collision spectral acquisition modes, which provide accurate mass full scan chromatograms and accurate mass high-energy chromatograms. Here, it is shown how this approach can be used to confirm carotenoid and chlorophyll species by identification of key diagnostic fragmentations during high-energy mode. The developed method was successfully applied for the analysis of Dunaliella salina samples during defined red LED lighting growth conditions, identifying 37 pigments including 19 carotenoid species and 18 chlorophyll species, and providing quantification of 7 targeted compounds. Limit of detections for targeted pigments ranged from 0.01?ng/mL for lutein to 0.24?ng/mL for chlorophyll a. Inter-run precision ranged for of 3 to 24 (RSD%) while inter-run inaccuracy ranged from ?17 to 11.

Visual detection and microplate assay for Staphylococcus aureus based on aptamer recognition coupled to tyramine signal amplification

We have developed a specific method for the visual detection of Staphylococcus aureus based on aptamer recognition coupled to tyramine signal amplification technology. A biotinylated aptamer specific for S. aureus was immobilized on the surface of the wells of a microplate via biotin-avidin binding. Then, the target bacteria (S. aureus), the biotinylated-aptamer-streptavidin-HRP conjugates, biotinylated tyramine, hydrogen peroxide and streptavidin-HRP were successively placed in the wells of the microplate. After adding TMB reagent and stop solution, the intensity of the yellow reaction product can be visually inspected or measured with a plate reader. Under optimized conditions, there is a linear relationship between absorbance at 450 nm and the concentration of S. aureus in the 10 to 10⁷ cfu mL^?1 concentration range (with an R² of 0.9976). The limit of detection is 8 cfu mL^?1.

New validated HPLC methodology for the determination of (−)-trans-paroxetine and its enantiomer in pharmaceutical formulations with use of ovomucoid chiral stationary phase

A new chromatographic method for the enantioseparation and the determination of (?)-trans-paroxetine and (+)-trans-paroxetine has been developed with the aid of amylose ovomucoid-based chiral stationary phase. The method is faster and five times more sensitive than procedures recommended previously: limit of detection and limit of quantification are 5 and 16 ng/mL, respectively [modified (Ferretti et al. in J Chromatogr B 710:157–164, 1998): 20 and 60 ng/mL]. It was carefully validated and applied for the determination of (?)-trans-paroxetine and (+)-trans-paroxetine in Parogen (Mc Dermott Laboratories Ltd.) and Xetanor (Actavis) coated tablets.

Determination of carbohydrates present in Saccharomyces cerevisiae using mid-infrared spectroscopy and partial least squares regression

A fast and simple method to control variations in carbohydrate composition of Saccharomyces cerevisiae, baker's yeast, during fermentation was developed using mid-infrared (mid-IR) spectroscopy. The method allows for precise and accurate determinations with minimal or no sample preparation and reagent consumption based on mid-IR spectra and partial least squares (PLS) regression. The PLS models were developed employing the results from reference analysis of the yeast cells. The reference analyses quantify the amount of trehalose, glucose, glycogen, and mannan in S. cerevisiae. The selection and optimization of pretreatment steps of samples such as the disruption of the yeast cells and the hydrolysis of mannan and glycogen to obtain monosaccharides were carried out. Trehalose, glucose, and mannose were determined using high-performance liquid chromatography coupled with a refractive index detector and total carbohydrates were measured using the phenol–sulfuric method. Linear concentration range, accuracy, precision, LOD and LOQ were examined to check the reliability of the chromatographic method for each analyte.

Enantioseparation of 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate tagged amino acids and other zwitterionic compounds on cinchona-based chiral stationary phases

The fluorescent tag 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate (AQC; AccQ Fluor reagent kit from Waters) is a commercial N-terminal label for proteinogenic amino acids (AAs), designed for reversed-phase separation and quantification of the AA racemates. The applicability of AQC-tagged AAs and AA-type zwitterionic compounds was tested for enantiomer separation on the tert-butyl carbamate modified quinine and quinidine based chiral stationary phases, QN-AX and QD-AX employing polar-organic elution conditions. The investigated test analytes included the enantiomers of the positional isomers of isoleucine (Ile), threonine, homoserine, and 4-hydroxyproline. Furthermore, β-AAs, cyclic, and heterocyclic AAs including trans-2-amino-cyclohexane carboxylic acid and trans-2-aminocyclohexyl sulfonic acid, phenylalanine derivatives substituted with halides with increasing electronegativity and 3,4-dihydroxyphenylalanine, cysteine-related derivatives including homocysteic acid, methionine sulfone, cysteine-S-acetic acid, and cysteine-S-acetamide as well as a small range of aminophosphonic acids were enantioseparated. A mechanistic interaction study of AQC-AAs in comparison with fluoresceine isothiocyanate-labeled AAs was performed. The chiral and chemoselective recognition processes involved in enantiomer separation and retention was systematically discussed. Special emphasis was set on the influential factors exhibited by the chemistry, branching position, and spatial properties of the investigated zwitterionic analytes. The general interest to separate and distinguish between different types of branched-chained AAs and metabolic side products thereof lies in the toxicity of some of these compounds, which makes for instance allo–Ile an attractive candidate in disease-related biomarker research.

Double stable isotope ultra performance liquid chromatographic-tandem mass spectrometric quantification of tissue content and activity of phenylethanolamine N-methyltransferase, the crucial enzyme responsible for synthesis of epinephrine

Here, we describe a novel method utilizing double stable isotope ultra performance liquid chromatography-tandem mass spectrometry to measure tissue contents and activity of phenylethanolamine N-methyltransferase (PNMT), the enzyme responsible for synthesis of the stress hormone, epinephrine. The method is based on measurement of deuterium-labeled epinephrine produced from the reaction of norepinephrine with deuterium-labeled S-adenosyl-l-methionine as the methyl donor. In addition to enzyme activity, the method allows for determination of tissue contents of PNMT using human recombinant enzyme for calibration. The calibration curve for epinephrine was linear over the range of 0.1 to 5,000 pM, with 0.5 pM epinephrine representing the lower limit of quantification. The calibration curve relating PNMT to production of deuterium-labeled epinephrine was also linear from 0.01 to 100 ng PNMT. Intra- and inter-assay coefficients of variation were respectively 12.8 % (n?=?10) and 10.9 to 13.6 % (n?=?10). We established utility of the method by showing induction of the enzyme by dexamethasone in mouse pheochromocytoma cells and strong relationships to PNMT gene expression and tissue epinephrine levels in human pheochromocytomas. Development of this assay provides new possibilities for investigations focusing on regulation of PNMT, the crucial final enzyme responsible for synthesis of epinephrine, the primary fight-or-flight stress hormone.

Extraction of phthalate esters from water and beverages using a graphene-based magnetic nanocomposite prior to their determination by HPLC

We have developed a highly sensitive microextraction method for the preconcentration of some phthalate esters such as diethyl phthalate, di-n-propylphthalate, di-n-butyl-phthalate, dicyclohexyl-phthalate, and diethyl-hexyl phthalate prior to their determination by HPLC. It is based on a magnetic graphene nanocomposite as an effective adsorbent. The effects of the amount of the extractant composite employed, extraction time, pH values, salt concentration and desorption conditions were investigated. Under the optimum conditions, the enrichment factors range from 1574 to 2880. Response is linear in the concentration range from 0.1 to 50?ng?mL^?1. The limits of detection (at S/N?=?3) were between 0.01 and 0.04?ng?mL^?1. The method was successfully applied to the determination of five phthalate esters in water and beverage samples.

New monolithic stir-cake-sorptive extraction for the determination of polar phenols by HPLC

A novel porous monolith has been prepared and used as a sorbent in stir-cake-sorptive extraction (SCSE). The monolithic material was prepared by in-situ copolymerization of allyl thiourea (AT) and divinylbenzene (DB) in the presence of dimethylformamide as a porogen solvent. To optimize the polymerization conditions, different monoliths with different ratios of functional monomer to porogenic solvent were prepared, and their extraction efficiency was investigated in detail. The monolith was characterized by elemental analysis, scanning electron microscopy, mercury intrusion porosimetry, and infrared spectroscopy. Analysis of polar phenols in environmental water samples by a combination of ATDB-SCSE and HPLC with diode-array detection was selected as a model for the practical application of the new sorbent. Several extraction conditions, including extraction and desorption time, pH, and ionic strength of the sample matrix were optimized. The results showed that the new monolith had high affinity for polar phenols and could be used to extract them effectively. Under the optimum conditions, low detection (S/N?=?3) and quantification (S/N?=?10) limits were achieved for the phenols, within the ranges 0.18–0.90 and 0.59–2.97 μg L^?1, respectively. The linearity of the method was good, and the method enabled simple, practical, and low-cost extraction of these analytes. The distribution coefficients between ATDB and water (K _ATDB/W) were calculated for the phenolic compounds and compared with K _O/W. Finally, the proposed method was successfully applied to the determination of the compounds in three environmental water samples, with acceptable recovery and satisfactory repeatability.

Rapid and sensitive detection of bacteria via platinum-labeled antibodies and on-particle ionization and enrichment prior to MALDI-TOF mass spectrometry

We introduce a rapid and sensitive approach to study the interactions of an affinity probe with the bacterial wall. Immunoglobulin was immobilized on platinum nanoparticles, and the resulting probe nanoparticles bind to bacterial walls as confirmed by transmission electron microscopy. A MALDI-MS assay was developed that can detect ~10⁵ cfu mL^?1 of S. marcescens and E. coli. This approach enables simple, rapid and straightforward detection of bacterial proteins, with high resolution and sensitivity, and without the requirement for tedious washing/separation steps.

Square wave anodic stripping voltammetric determination of lead(II) using a glassy carbon electrode modified with a lead ionophore and multiwalled carbon nanotubes

We report on a glassy carbon electrode (GCE) modified with a lead ionophore and multiwalled carbon nanotubes. It can be applied to square wave anodic stripping voltammetric determination of Pb(II) ion after preconcentration of Pb(II) at ?1.0?V (vs. SCE) for 300?s in pH?4.5 acetate buffer containing 400?μg?L^?1 of Bi(III). The ionophore-MWCNTs film on the GCE possesses strong and highly selective affinity for Pb(II) as confirmed by quartz crystal microbalance experiments. Under the optimum conditions, a linear response was observed for Pb(II) ion in the range from 0.3 to 50?μg?L^?1. The limit of detection (at S/N?=?3) is 0.1?μg?L^?1. The method was applied to the determination of Pb(II) in water samples with acceptable recovery.

Controlled Ion Ejection from an External Trap for Extended m/z Range in FT-ICR Mass Spectrometry

An auxiliary rf waveform of the same amplitude and phase applied to all the rods of an ion accumulation multipole creates an m/z-dependent axial pseudo potential. Controlled decrease of the auxiliary rf amplitude releases ions from the accumulation multipole sequentially from high to low m/z. The slope of the auxiliary rf voltage ramp is adjusted so that ions of different m/z reach the center of the ICR cell at the same time point, which mitigates the typical time dispersion observed in external source FT-ICR and extends the observable mass range for a single data acquisition by 2- to 3-fold. For complex mixture analysis, twice the number of elemental compositions are assigned when the auxiliary rf ejection is applied compared with the standard gated trapping.

Comparison and optimization of strategies for a more profound profiling of the sialylated N-glycoproteomics in human plasma using metal oxide enrichment

Glycosylation is an important posttranslational modification of proteins and plays a crucial role in both cellular functions and secretory pathways. Sialic acids (SAs), a family of nine-carbon-containing acidic monosaccharides, often terminate the glycan structures of cell surface molecules and secreted glycoproteins and perform an important role in many biological processes. Hence, a more profound profiling of the sialylated glycoproteomics may improve our knowledge of this modification and its effects on protein functions. Here, we systematically investigated different strategies to enrich the SA proteins in human plasma using a newly developed technology that utilizes titanium dioxide for sialylated N-glycoproteomics profiling by mass spectrometry. Our results showed that using a combination of a filter-aided sample preparation method, TiO₂ chromatography, multiple enzyme digestion, and two-dimensional reversed-phase peptide fractionation led to a more profound profiling of the SA proteome. In total, 982 glycosylation sites in 413 proteins were identified, among which 37.8 % were newly identified, to establish the largest database of sialic acid containing proteins from human plasma.

High-throughput absolute quantification of proteins using an improved two-dimensional reversed-phase separation and quantification concatemer (QconCAT) approach

Stable isotope dilution–selective reaction monitoring–mass spectrometry (SID-SRM-MS) has been widely used for the absolute quantitative analysis of proteins. However, when performing the large-scale absolute quantification of proteins from a more complex tissue sample, such as mouse liver, in addition to a high-throughput approach for the preparation and calibration of large amounts of stable-isotope-labelled internal standards, a more powerful separation method prior to SRM analysis is also urgently needed. To address these challenges, a high-throughput absolute quantification strategy based on an improved two-dimensional reversed-phase (2D RP) separation and quantification concatemer (QconCAT) approach is presented in this study. This strategy can be used to perform the simultaneous quantification of hundreds of proteins from mouse liver within one week of total MS measurement time. By using calibrated synthesised peptides from the protein glutathione S-transferase (GST), large amounts of GST-tagged QconCAT internal standards corresponding to hundreds of proteins can be accurately and rapidly quantified. Additionally, using an improved 2D RP separation method, a mixture containing a digested sample and QconCAT standards can be efficiently separated and absolutely quantified. When a maximum gradient of 72 min is employed in the first LC dimension, resulting in 72 fractions, identification and absolute quantification experiments for all fractions can be completed within one week of total MS measurement time. The quantification approach developed here can further extend the dynamic range and increase the analytical sensitivity of SRM analysis of complex tissue samples, thereby helping to increase the coverage of absolute quantification in a whole proteome.

Newborn screening of phenylketonuria using direct analysis in real time (DART) mass spectrometry

Phenylketonuria (PKU) is commonly included in the newborn screening panel of most countries, with various techniques being used for quantification of l-phenylalanine (Phe). To diagnose PKU as early as possible in newborn screening, a rapid and simple method of analysis was developed. Using direct analysis in real time (DART) ionization coupled with triple-quadrupole tandem mass spectrometry (TQ-MS/MS) and with use of a 12 DIP-it tip scanner autosampler in positive ion mode, we analyzed dried blood spot (DBS) samples from PKU newborns. The concentration of Phe was determined using multiple reaction monitoring mode with the nondeuterated internal standard N,N-dimethylphenylalanine. The results of the analysis of DBS samples from newborns indicated that the DART-TQ-MS/MS method is fast, accurate, and reproducible. The results prove that this assay as a newborn screen for PKU can be performed in 18 s per sample for the quantification of Phe in DBS samples. DART-TQ-MS/MS analysis of the Phe concentration in DBS samples allowed us to screen newborns for PKU. This innovative protocol is rapid and can be effectively applied on a routine basis to analyze a large number of samples in PKU newborn screening and PKU patient monitoring.

Sorption of platinum on immobilized microorganisms for its on-line preconcentration and chemiluminescent determination in water samples

Fungi of the type Aspergillus sp. were immobilized on a cellulosic resin and used as a biosorbent for the on-line preconcentration and separation of Pt(IV) ions prior to their chemiluminescent determination via flow injection analysis. Biosorption and elution conditions were optimized, and the results compared to biosorbents based on the use of Chlorella vulgaris algae and Saccharomyces cerevisiae yeast in terms of preconcentration and selective retention of Pt(IV). The immobilized fungi presented here have a high potential for use in platinum biosorption. The procedure exhibits the currently lowest limit of detection (0.02 ng mL^?1 of Pt) and very high selectivity. The procedure was applied to the determination of Pt(IV) in river water, road run-off, and wastewater samples.

Mass spectrometric profiling of Bacillus cereus strains and quantitation of the emetic toxin cereulide by means of stable isotope dilution analysis and HEp-2 bioassay

A fast and robust high-throughput ultra-performance liquid chromatography/time-of-flight mass spectrometry (UPLC–TOF MS) profiling method was developed and successfully applied to discriminate a total of 78 Bacillus cereus strains into no/low, medium and high producers of the emetic toxin cereulide. The data obtained by UPLC–TOF MS profiling were confirmed by absolute quantitation of cereulide in selected samples by means of high-performance liquid chromatography with tandem mass spectrometry (HPLC–MS/MS) and stable isotope dilution assay (SIDA). Interestingly, the B. cereus strains isolated from four vomit samples and five faeces samples from patients showing symptoms of intoxication were among the group of medium or high producers. Comparison of HEp-2 bioassay data with those determined by means of mass spectrometry showed differences, most likely because the HEp-2 bioassay is based on the toxic action of cereulide towards mitochondria of eukaryotic cells rather than on a direct measurement of the toxin. In conclusion, the UPLC–electrospray ionization (ESI)–TOF MS and the HPLC–ESI–MS/MS–SIDA analyses seem to be promising tools for the robust high-throughput analysis of cereulide in B. cereus cultures, foods and other biological samples.

Analysis of flame retardants and elements of concern in printed wiring boards with respect to origin and year of construction

Thirty-one populated printed wiring boards, covering a range of 30 years of construction, and originating from various electronic devices, were investigated using different analytical procedures. Noble, precious and rare metals, as well as environmentally relevant elements were identified by EDXRF, and lead and the flame retardant (FR) indicator bromine were localised by means of microbeam EDXRF. A GC/MS procedure was developed to identify and quantify FR substances. Several sample preparation techniques were applied, optimised and compared. The method of first choice was ultrasonic extraction because it provided the best compromise between effort, cost and quality of the analytical results. Altogether, a wide variety of elements of concern, and halogenated and phosphate-based FRs were found in the investigated boards. Their occurrence is partially related to the origin and/or year of construction.

A novel reversed-phase HPLC method for the determination of urinary creatinine by pre-column derivatization with ethyl chloroformate: comparative studies with the standard Jaffé and isotope-dilution mass spectrometric assays

Creatinine is an important biomarker for renal function diagnosis and normalizing variations in urinary drug/metabolites concentration. Quantification of creatinine in biological fluids such as urine and plasma is important for clinical diagnosis as well as in biomonitoring programs and urinary metabolomics/metabonomics research. Current methods for creatinine determination either are nonselective or involve the use of expensive mass spectrometers. In this paper, a novel reversed-phase high-performance liquid chromatographic (HPLC) method for the determination of creatinine of high hydrophilicity by pre-column derivatization with ethyl chloroformate is presented. N-Ethyloxycarbonylation of creatinine significantly enhanced the hydrophobicity of creatinine, facilitating its chromatographic retention as well as quantification by HPLC. Factors governing the derivatization reaction were studied and optimized. The developed method was validated and applied for the determination of creatinine in rat urine samples. Comparative studies with isotope-dilution mass spectrometric method revealed that the two methods do not yield systematic differences in creatinine concentrations, indicating the HPLC method is suitable for the determination of creatinine in urine samples.

Analysis of triacylglycerol hydroperoxides in human lipoproteins by Orbitrap mass spectrometer

Herein, we represent a simple method for the detection and characterization of molecular species of triacylglycerol monohydroperoxides (TGOOH) in biological samples by use of reversed-phase liquid chromatography with a LTQ Orbitrap XL mass spectrometer (LC/LTQ Orbitrap) via an electrospray ionization source. Data were acquired using high-resolution, high-mass accuracy in Fourier-transform mode. Platform performance, related to the identification of TGOOH in human lipoproteins and plasma, was estimated using extracted ion chromatograms with mass tolerance windows of 5 ppm. Native low-density lipoproteins (nLDL) and native high-density lipoproteins (nHDL) from a healthy donor were oxidized by CuSO₄ to generate oxidized LDL (oxLDL) and oxidized HDL (oxHDL). No TGOOH molecular species were detected in the nLDL and nHDL, whereas 11 species of TGOOH molecules were detected in the oxLDL and oxHDL. In positive-ion mode, TGOOH was found as [M + NH₄]⁺. In negative-ion mode, TGOOH was observed as [M + CH₃COO]^–. TGOOH was more easily ionized in positive-ion mode than in negative-ion mode. The LC/LTQ Orbitrap method was applied to human plasma and three molecular species of TGOOH were detected. The limit of detection is 0.1 pmol (S/N?=?10:1) for each synthesized TGOOH.