Determination of paralytic shellfish poisoning toxins in cultured microalgae by high-performance liquid chromatography with fluorescence detection

A novel method for the determination of paralytic shellfish poisoning (PSP) toxins using high-performance liquid chromatography with fluorescence detection was developed. The fluorescent derivates of neosaxitoxin (neoSTX), saxitoxin (STX), gonyautoxins 1 and 4 (GTX1+4), and gonyautoxins 2 and 3 (GTX2+3) were separated on a μBondapak NH₂ column (300 mm × 3.9 mm, 10 μm) using water and acetate buffer (pH 6.5) as the mobile phase (1.00 mL min⁻¹) in gradient mode with fluorescence detection at 390 nm (excitation at 330 nm). The linear ranges of neoSTX, STX, GTX1+4 and GTX2+3 were 3.31–331, 0.952–95.2, 3.78–378 and 0.124–12.4 ng mL⁻¹, respectively. The detection limits of neoSTX, STX, GTX1+4 and GTX2+3 were 1.10, 0.32, 1.26 and 0.041 ng mL⁻¹, respectively. The method was successfully applied to the determination of PSP toxins in microalgae. The recoveries ranged from 88±2% to 107±4% and the relative standard deviations were 0.16% to 4.4%. The procedure is also environmentally friendly because no organic solvent is used in the mobile phase.     

Electrogenerated chemiluminescence from thiol-capped CdTe quantum dots and its sensing application in aqueous solution

In this paper, the electrogenerated chemiluminescence (ECL) from thiol-capped CdTe quantum dots (QDs) was reported. The ECL emission was occurred at −1.1 V and reached a maximum value at −2.4 V when the potential was cycled between 0.0 and −2.5 V. The reduced species of CdTe QDs could react with the coreactants to produce the ECL emission. The CdTe QD concentration (6.64 × 10⁻⁷ mol L⁻¹) of ECL is lower than that (1.0 × 10⁻³ mol L⁻¹) of chemiluminescence (CL). Based on the enhancement of light emission from thiol-capped CdTe QDs by H₂O₂ in the negative electrode potential, a novel method for the determination of H₂O₂ was developed. The light intensity was linearly proportional to the concentration of H₂O₂ between 2.0 × 10⁻⁷ and 1.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 6.0 × 10⁻⁸ mol L⁻¹. Compared with most of previous reports, the proposed method has higher sensitivity for the determination of H₂O₂. In addition, the ECL spectrum of thiol-capped CdTe QDs exhibited a peak at around 620 nm, which was substantially red shifted from the photoluminescence (PL) spectrum, suggesting the surface states play an important role in this ECL process.     

Ultrasensitive fluorometric determination of hydrogen peroxide and glucose by using multiferroic BiFeO3 nanoparticles as a catalyst

BiFeO₃ magnetic nanoparticles (BFO MNPs) are used as a catalyst to develop an ultrasensitive method for the determination of H₂O₂. It is found that BFO MNPs can catalyze the decomposition of H₂O₂ to produce OH radicals, which in turn oxidize the weakly fluorescent benzoic acid to a strongly fluorescent hydroxylated product with a maximum emission at 405 nm. This makes it possible to sensitively quantify traces of H₂O₂. Under optimized conditions, the fluorescence intensity is observed to be well linearly correlated with H₂O₂ concentration from 2.0 × 10⁻⁸ to 2.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 4.5 × 10⁻⁹ mol L⁻¹ (S/N = 3). In addition, a selective method for glucose determination is developed by using both glucose oxidase and BFO MNPs, which has a linear range for glucose concentration from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. These new methods have been successfully applied for the determination of H₂O₂ in rainwater and glucose in human serum samples.     

Application of Fenton reaction for nanomolar determination of hydrogen peroxide in seawater

A simple and sensitive method for the determination of nanomolar levels of hydrogen peroxide (H₂O₂) in seawater has been developed and validated. This method is based on the reduction of H₂O₂ by ferrous iron in acid solution to yield hydroxyl radical (OH) which reacts with benzene to produce phenol. Phenol is separated from the reaction mixture by reversed phase high performance liquid chromatography and its fluorescence intensity signals were measured at excitation and emission of 270 and 298 nm, respectively. Under optimum conditions, the calibration curve exhibited linearity in the range of (0-50) × 10³ nmol L⁻¹ H₂O₂. The relative standard deviations for five replicate measurements of 500 and 50 nmol L⁻¹ H₂O₂ are 1.9 and 2.4%, respectively. The detection limit for H₂O₂, defined as three times the standard deviation of the lowest standard solution (5 nmol L⁻¹ H₂O₂) in seawater is 4 nmol L⁻¹. Interference of nitrite ion (NO₂⁻) on the fluorescence intensity of phenol was also investigated. The result indicated that the addition of 10 μmol L⁻¹ NO₂⁻ to seawater samples showed no significant interference, although, the addition of 50 μmol L⁻¹ NO₂⁻ to the seawater samples decreases the fluorescence intensity signals of phenol by almost 40%. Intercomparison of this method with well-accepted (p-hydroxyphenyl) acetic acid (POHPAA)-FIA method shows excellent agreement. The proposed method has been applied on-board analysis of H₂O₂ in Seto Inland seawater samples.     

Multi-detection method for five common microalgal toxins based on the use of microspheres coupled to a flow-cytometry system

Freshwater and brackish microalgal toxins, such as microcystins, cylindrospermopsins, paralytic toxins, anatoxins or other neurotoxins are produced during the overgrowth of certain phytoplankton and benthic cyanobacteria, which includes either prokaryotic or eukaryotic microalgae. Although, further studies are necessary to define the biological role of these toxins, at least some of them are known to be poisonous to humans and wildlife due to their occurrence in these aquatic systems. The World Health Organization (WHO) has established as provisional recommended limit 1 μg of microcystin-LR per liter of drinking water. In this work we present a microsphere-based multi-detection method for five classes of freshwater and brackish toxins: microcystin-LR (MC-LR), cylindrospermopsin (CYN), anatoxin-a (ANA-a), saxitoxin (STX) and domoic acid (DA). Five inhibition assays were developed using different binding proteins and microsphere classes coupled to a flow-cytometry Luminex system. Then, assays were combined in one method for the simultaneous detection of the toxins. The IC₅₀'s using this method were 1.9 ± 0.1 μg L⁻¹ MC-LR, 1.3 ± 0.1 μg L⁻¹ CYN, 61 ± 4 μg L⁻¹ ANA-a, 5.4 ± 0.4 μg L⁻¹ STX and 4.9 ± 0.9 μg L⁻¹ DA. Lyophilized cyanobacterial culture samples were extracted using a simple procedure and analyzed by the Luminex method and by UPLC–IT-TOF-MS. Similar quantification was obtained by both methods for all toxins except for ANA-a, whereby the estimated content was lower when using UPLC–IT-TOF-MS. Therefore, this newly developed multiplexed detection method provides a rapid, simple, semi-quantitative screening tool for the simultaneous detection of five environmentally important freshwater and brackish toxins, in buffer and cyanobacterial extracts.     

Development of novel and sensitive methods for the determination of sulfide in aqueous samples by hydrogen sulfide generation-inductively coupled plasma-atomic emission spectroscopy

Two new, simple and accurate methods for the determination of sulfide (S²⁻) at low levels (μg L⁻¹) in aqueous samples were developed. The generation of hydrogen sulfide (H₂S) took place in a coil where sulfide reacted with hydrochloric acid. The resulting H₂S was then introduced as a vapor into an inductively coupled plasma-atomic emission spectrometer (ICP-AES) and sulfur emission intensity was measured at 180.669 nm. In comparison to when aqueous sulfide was introduced, the introduction of sulfur as H₂S enhanced the sulfur signal emission. By setting a gas separator at the end of the reaction coil, reduced sulfur species in the form of H₂S were removed from the water matrix, thus, interferences could be avoided. Alternatively, the gas separator was replaced by a nebulizer/spray chamber combination to introduce the sample matrix and reagents into the plasma. This methodology allowed the determination of both sulfide and sulfate in aqueous samples. For both methods the linear response was found to range from 5 μg L⁻¹ to 25 mg L⁻¹ of sulfide. Detection limits of 5 μg L⁻¹ and 6 μg L⁻¹ were obtained with and without the gas separator, respectively. These new methods were evaluated by comparison to the standard potentiometric method and were successfully applied to the analysis of reduced sulfur species in environmental waters.     

Application of sequential injection-square wave voltammetry (SI-SWV) to study the adsorption of atrazine onto a tropical soil sample

Square wave voltammetry automated by sequential injection analysis was applied to determine the Freundlich adsorption coefficients for the adsorption of atrazine onto a clay rich soil. The detection limit in soil extracts was between 0.18 and 0.48 μmol L⁻¹, depending on the medium used to prepare the extracts (0.010 mol L⁻¹ KCl, CaCl₂ or HNO₃ and 0.0050 mol L⁻¹ H₂SO₄), all of them conditioned in 40 mmol L⁻¹ Britton-Robinson buffer at pH 2.0 in presence of 0.25 mol L⁻¹ NaNO₃. Also in soil extracts the linear dynamic range was between 1.16 and 18.5 μmol L⁻¹ (0.25-4.0 μg mL⁻¹), with a sampling frequency of 190 h⁻¹. The K_f Freundlich adsorption coefficient was 3.8 ± 0.2 μmol^1−1/n Lⁿ kg⁻¹ in medium of 0.010 mol L⁻¹ KCl or CaCl₂, but increased to 7.7 ± 0.1 and 9.0 ± 0.3 μmol^1−1/n Lⁿ kg⁻¹ in 0.010 mol L⁻¹ HNO₃ and 0.0050 mol L⁻¹ H₂SO₄, respectively. The increase of K_f was related to the decrease of pH from 6.4-6.7 in KCl and CaCl₂ to 3.7-4.0 in presence of HNO₃ or H₂SO₄, which favors protonation of atrazine, facilitating electrostatic attractions with negative charges of the clay components of the soil. The 1/n parameters were between 0.76 and 0.86, indicating that the isotherms are not linear, suggesting the occurrence of chemisorption at specific adsorption sites. No statistically significant differences were observed in comparison to the adsorption coefficients obtained by HPLC. The advantage of the proposed SI-SWV method is the great saving of reagent because it does not use organic solvent as in the case of HPLC (50% (v/v) acetonitrile in the mobile phase). Additionally the start up of SI-SWV is immediate (no column conditioning necessary) and the analysis time is only 19 s.     

Simple and fast spectrophotometric determination of H(2)O(2) in photo-Fenton reactions using metavanadate

This work proposes a spectrophotometric method for the determination of hydrogen peroxide during photodegradation reactions. The method is based on the reaction of H₂O₂ with amonium metavanadate in acidic medium, which results in the formation of a red-orange color peroxovanadium cation, with maximum absorbance at 450 nm. The method was optimized using the multivariate analysis providing the minimum concentration of vanadate (6.2 mmol L⁻¹) for the maximum absorbance signal. Under these conditions, the detection limit is 143 μmol L⁻¹. The reaction product showed to be very stable for samples of peroxide concentrations up to 3 mmol L⁻¹ at room temperature during 180 h. For higher concentrations however, samples must be kept refrigerated (4 °C) or diluted. The method showed no interference of Cl⁻ (0.2-1.3 mmol L⁻¹), NO₃⁻ (0.3-1.0 mmol L⁻¹), Fe³⁺ (0.2-1.2 mmol L⁻¹) and 2,4-dichlorophenol (DCP) (0.2-1.0 mmol L⁻¹). When compared to iodometric titration, the vanadate method showed a good agreament. The method was applied for the evaluation of peroxide consumption during photo-Fenton degradation of 2,4-dichlorophenol using blacklight irradiation.     

A portable and low cost equipment for flow injection chemiluminescence measurements

A compact, reliable and low cost flow injection chemiluminescence system is described. The flow system consists of a set of solenoid micro-pumps that can dispense reproductive micro-volumes of solutions. The luminometer was based on a coiled cell constructed from polyethylene tubing that was sandwiched between two large area photodiodes. The whole equipment costs about US$ 750 and weights ca. 3 kg. Equipment performance was evaluated by measuring low concentrations of hydrogen peroxide by oxidation of luminol and for the determination of ammonium, based on its inhibition of the luminescence provided by the reaction of luminol and sodium hypochlorite. Linear responses were achieved within 1.0-80 μmol L⁻¹ H₂O₂ and 0.6-60 μmol L⁻¹ NH₄⁺ with detection limits estimated as 400 nmol L⁻¹ H₂O₂ and 60 nmol L⁻¹ NH₄⁺ at the 99.7% confidence level. Coefficients of variation were 1.0 and 1.8%, estimated for 20 μmol L⁻¹ H₂O₂ and 15 μmol L⁻¹ NH₄⁺ (n = 20), respectively. Reagent consumption of 55 μg luminol, effluent volume of 950 μL per determination and sampling rate of 120 samples per hour were also achieved.     

Determination of hydrogen sulfide and volatile thiols in air samples by mercury probe derivatization coupled with liquid chromatography-atomic fluorescence spectrometry

A new procedure is proposed for the sampling and storage of hydrogen sulphide (H₂S) and volatile thiols (methanethiol or methyl mercaptan, ethanethiol and propanethiol) for their determination by liquid chromatography. The sampling procedure is based on the trapping/pre-concentration of the analytes in alkaline aqueous solution containing an organic mercurial probe p-hydroxymercurybenzoate, HO-Hg-C₆H₄-COO⁻ (PHMB), where they are derivatized to stable PHMB complexes based on mercury-sulfur covalent bonds. PHMB complexes are separated on a C₁₈ reverse phase column, allowing their determination by liquid chromatography coupled with sequential non-selective UV-vis (DAD) and mercury specific (chemical vapor generation atomic fluorescence spectrometry, CVGAFS) on-line detectors. PHMB complexes, S(PHMB)₂CH₃S-PHMB, C₂H₅S-PHMB and C₃H₇S-PHMB, are stable alt least for 12 h at room temperature and for 3 months if stored frozen (−20 °C).The best analytical figures of merits in the optimized conditions were obtained by CVGAFS detection, with detection limits (LODc) of 9.7 μg L⁻¹ for H₂S, 13.7 μg L⁻¹ for CH₃SH, 17.7 μg L⁻¹ for C₂H₅SH and 21.7 μg L⁻¹ for C₃H₇SH in the trapping solution in form of RS-PHMB complexes, the relative standard deviation (R.S.D.) ranging between 1.0 and 1.5%, and a linear dynamic range (LDR) between 10 and 9700 μg L⁻¹. Conventional UV absorbance detectors tuned at 254 nm can be employed as well with comparable R.S.D. and LDR, but with LODc one order of magnitude higher than AFS detector and lower specificity. The sampling procedure followed by LC-DAD-CVGAFS analysis has been validated, as example, for H₂S determination by a certified gas permeation tube as a source of 3.071 ± 0.154 μg min⁻¹ of H₂S, giving a recovery of 99.8 ± 7% and it has been applied to the determination of sulfur compounds in real gas samples (biogas and the air of a plant for fractional distillation of crude oil).     

A homogeneous assay principle for universal substrate quantification via hydrogen peroxide producing enzymes

H₂O₂ is a widely occurring molecule which is also a byproduct of a number of enzymatic reactions. It can therefore be used to quantify the corresponding enzymatic substrates. In this study, the time-resolved fluorescence emission of a previously described complex consisting of phthalic acid and terbium (III) ions (PATb) is used for H₂O₂ detection. In detail, glucose oxidase and choline oxidase convert glucose and choline, respectively, to generate H₂O₂ which acts as a quencher for the PATb complex. The response time of the PATb complex toward H₂O₂ is immediate and the assay time only depends on the conversion rate of the enzymes involved. The PATb assay quantifies glucose in a linear range of 0.02–10 mmol L⁻¹, and choline from 1.56 to 100 μmol L⁻¹ with a detection limit of 20 μmol L⁻¹ for glucose and 1.56 μmol L⁻¹ for choline. Both biomolecules glucose and choline could be detected without pretreatment with good precision and reproducibility in human serum samples and infant formula, respectively. Furthermore, it is shown that the detected glucose concentrations by the PATb system agree with the results of a commercially available assay. In principle, the PATb system is a universal and versatile tool for the quantification of any substrate and enzyme reaction where H₂O₂ is involved.     

Development of a gold nanoparticles based chemiluminescence imaging assay and its application

In this paper, a novel gold nanoparticles based protein immobilization method was designed. Biocomposites of gold nanoparticles and proteins were successfully coated on poly(methyl methacrylate) (PMMA) plates and polystyrene microtiter plates. The proteins could be immobilized on solid materials with high density and better bioactivity. Based on above design, chemiluminescence (CL) imaging assay for determination of H₂O₂ and recombinant human interleukin-6 (rHu IL-6) was developed. The linear range and the loading capability were greatly improved when compared with imaging assay performed with direct proteins immobilization. Under the selected experimental conditions, a linear relationship was obtained between the CL intensity and the concentration of H₂O₂ in the range of 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹, and rHu IL-6 in the range of 2.0-312.0 pg mL⁻¹. The detection limits were 2 × 10⁻⁷ mol L⁻¹ (3σ) for H₂O₂ and 0.5 pg mL⁻¹ for rHu IL-6 with relative standard deviation of 3.8% for 3.0 × 10⁻⁵ mol L⁻¹ H₂O₂, and 4.4% for 39.0 pg mL⁻¹ rHu IL-6. This method has been applied to the determination of rHu IL-6 in human serum with satisfactory results.     

Electrodeposition of gold nanoparticles on indium/tin oxide electrode for fabrication of a disposable hydrogen peroxide biosensor

A novel disposable third-generation hydrogen peroxide (H₂O₂) biosensor based on horseradish peroxidase (HRP) immobilized on the gold nanoparticles (AuNPs) electrodeposited indium tin oxide (ITO) electrode is investigated. The AuNPs deposited on ITO electrode were characterized by UV-vis, SEM, and electrochemical methods. The AuNPs attached on the ITO electrode surface with quasi-spherical shape and the average size of diameters was about 25 nm with a quite symmetric distribution. The direct electron chemistry of HRP was realized, and the biosensor exhibited excellent performances for the reduction of H₂O₂. The amperometric response to H₂O₂ shows a linear relation in the range from 8.0 μmol L⁻¹ to 3.0 mmol L⁻¹ and a detection limit of 2 μmol L⁻¹ (S/N = 3). The value of HRP immobilized on the electrode surface was found to be 0.4 mmol L⁻¹. The biosensor indicates excellent reproducibility, high selectivity and long-term stability.     

Development of a single-chain variable fragment-alkaline phosphatase fusion protein and a sensitive direct competitive chemiluminescent enzyme immunoassay for detection of ractopamine in pork

A rapid, sensitive chemiluminescent enzyme immunoassay (CLEIA) for ractopamine (RAC) based on a single-chain variable fragment (scFv)-alkaline phosphatase (AP) fusion protein was developed. The scFv gene was prepared by cloning the heavy- and light-chain variable region genes (V_H and V_L) from hybridoma cell line AC2, which secretes antibodies against RAC, and assembling V_H and V_L genes with a linker by means of splicing overlap extension polymerase chain reaction. The resulting scFv gene was inserted into the expression vector pLIP6/GN containing AP to produce the fusion protein in Escherichia coli strain BL21. The purified scFv-AP fusion protein was used to develop a direct competitive CLEIA (dcCLEIA) protocol for detection of RAC. The average concentration required for 50% inhibition of binding and the limit of detection of the assay were 0.25 ± 0.03 and 0.02 ± 0.004 ng mL⁻¹, respectively, and the linear response range extended from 0.05 to 1.45 ng mL⁻¹. The assay was 10 times as sensitive as the corresponding enzyme-linked immunosorbent assay based on the same fusion protein. Cross-reactivity studies showed that the fusion protein did not cross react with RAC analogs. DcCLEIA was used to analyze RAC spiked pork samples, and the validation was confirmed by high-performance liquid chromatography–tandem mass spectrometry (HPLC–MS). The results showed a good correlation between the data of dc-CLEIA and HPLC–MS (R² > 0.99), indicating that the assay was an efficient analytical method for monitoring food safety.     

FIA-near-infrared spectrofluorimetric trace determination of hydrogen peroxide using tricarchlorobocyanine dye (Cy.7.Cl) and horseradish peroxidase (HRP)

A new kind of near-infrared fluorescence agent, tricarbochlorocyanine dye (Cy.7.Cl), had been synthesized in house and used for near-infrared spectrofluorimetric determination of hydrogen peroxide (H₂O₂) by flow injection analysis (FIA) for the first time. The oxidation reaction of Cy.7.Cl with H₂O₂ occurred under the catalysis of horseradish peroxidase (HRP) and it was studied in detail. The possible reaction mechanism was discussed. Under optimal experimental conditions, fluorescence from Cy.7.Cl displayed excitation and emission maxima (ex/em) at 780 and 800 nm, respectively. The two linear working ranges were 1.86 × 10⁻⁷ to 4.11 × 10⁻⁷ mol L⁻¹ and 4.11 × 10⁻⁷ to 7.19 × 10⁻⁶ mol L⁻¹, respectively. The detection limit was 5.58 × 10⁻⁸ mol L⁻¹ of H₂O₂. The effect of interferences was studied. The proposed method was successfully applied to the determination of hydrogen peroxide in rainwater, serum and plant samples.     

Determination of mercury species by the diffusive gradient in thin film technique and liquid chromatography – atomic fluorescence spectrometry after microwave extraction

A diffusive gradient in thin films technique (DGT) was combined with liquid chromatography (LC) and cold vapor atomic fluorescence spectrometry (CV-AFS) for the simultaneous quantification of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, and C₆H₅Hg⁺). After diffusion through an agarose diffusive layer, the mercury species were accumulated in resin gels containing thiol-functionalized ion-exchange resins (Duolite GT73, and Ambersep GT74). A microwave-assisted extraction (MAE) in the presence of 6 M HCl and 5 M HCl (55 °C, 15 min) was used for isolation of mercury species from Ambersep and Duolite resin gels, respectively. The extraction efficiency was higher than 95.0% (RSD 3.5%). The mercury species were separated with a mobile phase containing 6.2% methanol + 0.05% 2-mercaptoethanol + 0.02 M ammonium acetate with a stepwise increase of methanol content up to 80% in the 16th min on a Zorbax C18 reverse phase column. The LODs of DGT–MAE–LC–CV-AFS method were 38 ng L⁻¹ for CH₃Hg⁺, 13 ng L⁻¹ for Hg²⁺, 34 ng L⁻¹ for C₂H₅Hg⁺ and 30 ng L⁻¹ for C₆H₅Hg⁺ for 24 h DGT accumulation at 25 °C.     

Dithizone immobilized silica gel on-line preconcentration of trace copper with detection by flame atomic absorption spectrometry

A novel adsorbent-silica gel bound dithizone (H₂Dz-SG) was prepared and used as solid-phase extraction of copper from complex matrix. The H₂Dz-SG is investigated by means of FT-IR spectra and the SEM images, demonstrating the bonding of dithizone. The H₂Dz-SG quantitatively adsorb copper ions, and the retained copper is afterwards collected by elution of 10% (v/v) nitric acid. An on-line flow injection solid-phase extraction procedure was developed for trace copper separation and preconcentration with detection by flame atomic spectrometry. By loading 5.4 mL of sample solution, a liner range of 0.5-120 μg L⁻¹, an enrichment factor of 42.6, a detection limit of 0.2 μg L⁻¹ and a precision of 1.7% RSD at the 40 μg L⁻¹ level (n = 11) were obtained, along with a sampling frequency of 47 h⁻¹. The dynamic sorption capacity of H₂Dz-SG to Cu²⁺ was 0.76 mg g⁻¹. The accuracy of the proposed procedure was evaluated by determination of copper in reference water sample. The potential applications of the procedure for extraction of trace copper were successfully accomplished in water samples (tap, rain, snow, sea and river). The spiking recoveries within 91-107% are achieved.     

Comparison of biosensor platforms for surface plasmon resonance based detection of paralytic shellfish toxins

Paralytic shellfish poisoning (PSP) toxins are produced by certain marine dinoflagellates and may accumulate in bivalve molluscs through filter feeding. The Mouse Bioassay (MBA) is the internationally recognised reference method of analysis, but it is prone to technical difficulties and regarded with increasing disapproval due to ethical reasons. As such, alternative methods are required. A rapid surface plasmon resonance (SPR) biosensor inhibition assay was developed to detect PSP toxins in shellfish by employing a saxitoxin polyclonal antibody (R895). Using an assay developed for and validated on the Biacore Q biosensor system, this project focused on transferring the assay to a high-throughput, Biacore T100 biosensor in another laboratory. This was achieved using a prototype PSP toxin kit and recommended assay parameters based on the Biacore Q method. A monoclonal antibody (GT13A) was also assessed. Even though these two instruments are based on SPR principles, they vary widely in their mode of operation including differences in the integrated μ-fluidic cartridges, autosampler system, and sensor chip compatibilities. Shellfish samples (n = 60), extracted using a simple, rapid procedure, were analysed using each platform, and results were compared to AOAC high performance liquid chromatography (HPLC) and MBA methods. The overall agreement, based on statistical 2 × 2 comparison tables, between each method ranged from 85% to 94.4% using R895 and 77.8% to 100% using GT13A. The results demonstrated that the antibody based assays with high sensitivity and broad specificity to PSP toxins can be applied to different biosensor platforms.     

Simple and selective determination of arsenite and arsenate by electrospray ionization mass spectrometry

Arsenic pollution of public water supplies has been reported in various regions of the world. Recently, some cancer patients are treated with arsenite (As^III); most Japanese people consume seafoods containing large amounts of negligibly toxic arsenic compounds. Some of these arsenic species are metabolized, but some remain intact. For the determination of toxic As^III, a simple, rapid and sensitive method has been developed using electrospray ionization mass spectrometry (ESI-MS). As^III was reacted with a chelating agent, pyrrolidinedithiocarbamate (PDC, C₄H₈NCSS^-) and tripyrrolidinedithiocarbamate-arsine, As(PDC)₃, extracted with methyl isobutyl ketone (MIBK). A 1 μL aliquot of MIBK layer was directly injected into ESI-MS instrument without chromatographic separation, and was detected within 1 min. Arsenate (As^V) was reduced to As^III with thiosulfate, and then the total inorganic As was quantified as As^III. This method was validated for the analysis of urine samples. The limit of detection of As was 0.22 μg L⁻¹ using 10 μL of sample solution, and it is far below the permissible limit of As in drinking water, 10 μg L⁻¹, recommended by the WHO. Results were obtained in < 10 min with a linear calibration range of 1-100 μg L⁻¹. Several organic arsenic compounds in urine did not interfere with As^III detection, and the inorganic As in the reference materials SRM 2670a and 1643e were quantified after the reduction of As^V to As^III.     

Bilayer lipid membrane biosensor with enhanced stability for amperometric determination of hydrogen peroxide

In this paper, a polydopamine (PDA) film is electropolymerized on the surface of bilayer lipid membrane (BLM) which is immobilized with horseradish peroxidase (HRP). The coverage of the PDA film on HRP/BLM electrode is monitored by electrochemical impedance spectroscopy (EIS). The electrocatalytic reduction of H₂O₂ at the PDA/HRP/BLM electrode is studied by means of cyclic voltammetry (CV). The biosensor has a fast response to H₂O₂ of less than 5 s and an excellent linear relationship is obtained in the concentration range from 2.5 × 10⁻⁷ to 3.1 × 10⁻³ mol L⁻¹, with a detection limit of 1.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The response current of BLM/HRP/PDA biosensor retains 84% of its original response after being stored in 0.1 mol L⁻¹ pH 7.0 PBS at 4 °C for 3 weeks. The selectivity, repeatability, and storage stability of PDA/HRP/BLM biosensor are greatly enhanced by the coverage of polydopamine film on BLM.