Slurry Sampling Electrothermal Vaporization Combined with ICP-AES for Direct Analysis of Environmental Samples

In this article, a polytetrafluoroethylene (PTFE) slurry was used as a chemical modifier for direct determination of trace elements in environmental samples by electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. The vaporization behaviors of the analytes in slurry and solution were comparatively studied in the presence of PTFE. The main influence factors for this method were examined. Under the optimum operating conditions, the precision of this method was better than 7% with the detection limits varying from 1.7 ng mL^?1 (Cu) to 203 ng mL^?1 (Zn). The proposed method has been applied to the direct determination of the trace elements in camphor tree leaves and standard reference material (the combined sample of branch and leaf of shrub, GBW 07603) with satisfactory results.     

Determination of traces of As,Cd, Cr,Hg, Mn,Ni, Sb,Se, Sn and Pb in human hair by triple quadrupole ICP-MS

With the wide range of metallic contaminants discharged in the environment, studying the human health requires a growing number of elements to be monitored in biological samples. Hair analysis has been suggested as a suitable tool for biomonitoring environmental and occupational exposure to toxic elements. This study describes a method for the determination of 10 trace elements in hair samples using ICP-QQQ-MS. Combining the power of the MS/MS high-energy Helium mode with the MS/MS O₂ mass-shift mode, the method offers great analytical performances with detection limits reaching 0.0014 µg g^?1 for As, 0.0016 µg g^?1 for Cd, 0.012 µg g^?1 for Cr, 0.0035 µg g^?1 for Hg, 0.0055 µg g^?1 for Mn, 0.10 µg g^?1 for Ni, 0.0012 µg g^?1 for Sb, 0.0083 µg g^?1 for Sn, 0.011 µg g^?1 for Se and Pb. The accuracy of the method was tested on a human hair ERM® certified reference material. Percent recoveries varied from 91.3% and 106.9% being always in the acceptance range of 90–110%. For all analysed elements, RSD% of repeatability ranged between 0.6% and 9.0% and those of intermediate precision did not exceed the limit of 20% being always lower than 10% (except for As). The proposed method was applied for the determination of trace elements in hair samples from 20 unexposed subjects. The geometric mean levels were as follows: Cr 0.28 µg g^?1, Mn 0.30 µg g^?1, Sn 1.04µg g^?1, Sb 0.07 µg g^?1, Hg 0.42 µg g^?1, As 0.02 µg g^?1, Cd 0.03 µg g^?1, Ni 0.51 µg g^?1, Se 0.45 µg g^?1 and Pb 1.83 µg g^?1. Element concentrations were in the same range with the reported data. The reported results may be useful for environmental exposure assessment or comparisons studies when establishing reference values of trace elements in exposed population.     

On-line solid phase extraction coupled to flame atomic absorption spectrometry for the determination of trace copper and zinc in environmental and biological samples

In this work, bamboo charcoal (BC) was used as a sorbent for on-line solid phase extraction (SPE) coupling with flame atomic absorption spectrometry (AAS) for trace copper and zinc determination in environmental and biological samples. Under the optimum pH of 5.5 (for Zn) and 7.0 (for Cu), trace copper and zinc were effectively adsorbed on the microcolumn and the retained cations were efficiently eluted with HCl or HNO₃ with an appropriate concentration and flow rate for on-line AAS determination. With a sample loading time of 60 s at a sample flow rate of 7.6 mL min^?1, the enhancement factors of 39 (for Cu) and 30 (for Zn) and detection limits (3σ) of 0.60 µg L^?1 (for Cu) and 0.36 µg L^?1 (for Zn), respectively, were achieved. The sample throughput was 45 h^?1. At the level of 20 µg L^?1of Cu(II) and Zn(II), the precision (RSD, n?=?11) were found to be 0.26% and 1.6%, respectively. The proposed method has been successfully applied to the determination of copper and zinc in environmental and biological samples.     

Chemically modified silica gel for selective solid-phase extraction and preconcentration of heavy metal ions

This paper describes our research on the synthesis of the sorbent with chemically bonded ketoimine groups, and, furthermore, using this sorbent in the SPE technique to extract and preconcentrate trace amounts of metal ions in water samples. Surface characteristics of the sorbent were determined by elemental analysis, NMR spectra for the solid phases (²⁹Si CP MAS NMR), and analysis of pore size distribution of the sorbent and nitrogen adsorption-desorption. The newly proposed sorbent with ketoimine groups was applied for the extraction and preconcentration of trace amounts of Cu (II), Cr (III) and Zn (II) ions from the water from a lake, post-industrial water and purified water unburdened back to the lake. The determination of the transition-metal ions was performed on an emission spectroscope with inductively coupled plasma ICP-OES. For the batch method, the optimum pH range for Cu (II) and Cr (III) extraction was equal to 5, and Zn(II)–to 8. All the metal ions can be desorbed from SPE columns with 10?mL of 0.5?mol?HNO₃. The detection limits of the method were found to be 0.7?µg?L^?1 for Cu (II), 0.08?µg?L^?1 for Cr (III), and 0.2?µg?L^?1 for Zn (II), respectively.     

Trace elements in sediments and bioaccumulation in European silver eels (Anguilla anguilla L.) from a Mediterranean lagoon (SE Italy)

Samples of surface sediments and tissues (liver and muscle) of commercially available European silver eels (Anguilla anguilla L.) collected from Varano lagoon (Italy) were analysed to determine trace element contents. Univariate and multivariate analyses were performed to highlight both the differences between sampling sites and the influence of channel discharges. Atomic ratios indices for sediment data and biological enrichment factors (BEF) for eel tissues were calculated in order to evaluate the enrichment factor due to human activities. The highest levels of As (11.9?µg?g^?1) and Zn (14.1?µg?g^?1) were observed in the south-eastern zone of the lagoon, which is influenced by urban and agricultural discharges. The low levels of Hg observed in this study (0.04?µg?g^?1) led us to exclude both natural and human local sources of this element. Trace element concentrations of all elements were lower in muscle than in liver tissue. Significant enrichment of Cu and Zn was found in livers.     

Slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry for the direct determination of metal impurities in aluminium oxide ceramic powders

A new analytical procedure for the direct determination of metal impurities (Cr, Cu, Fe and V) in aluminium oxide ceramic powders by slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICP-AES) is reported. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of impurity elements in aluminium oxide ceramic powders from the graphite tube. A vaporization stage with a long ramp time and a short hold time provided the possibility of temporal analyte-matrix separation. The experimental results indicated that a 10 μL 1% m/v slurry of aluminium oxide could be destroyed and vaporized completely with 600 μg PTFE under the selected conditions. Two aluminium oxide ceramic powder samples were used without any additional pretreatment. Analytical results obtained by using standard addition method with aqueous standard solution were checked by comparison of the results with pneumatic nebulization (PN)-ICP-AES based on the wet-chemical decomposition and analyte-matrix separation. The limits of detection (LODs) between 0.30 μg g^–1 (Fe ) and 0.08 μg g^–1 (Cu) were achieved, and, the repeatability of measurements was mainly better than 10%. Received: 28 August 2000 / Revised: 1 November 2000 / Accepted: 12 November 2000     

Electrothermal vaporization in inductively coupled plasma atomic emission spectrometry for direct multielement analysis of food samples with slurry sampling

Slurry sampling followed by electrothermal vaporization (ETV) was used as sample introduction technique in inductively coupled plasma atomic emission spectrometry (ICP-AES) for the direct determination of trace elements in food samples. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote vaporization and the transportation of analytes. The main factors affecting the analytical signals were investigated in detail. Under optimum operating conditions, the detection limits (DL) for this method varied from 1.8 (Cu) to 215 ng/mL (Zn), while the relative standard deviations (RSD) were in the range 2.6% (Cu)-7.2% (Zn). The proposed method was successfully applied to the direct determination of trace amounts of V, Cu, Cr, Fe, Zn, and La in rice without any chemical pretreatment. The precision was evaluated by analyzing a standard reference material (tea leaves, GBW 07605) and comparing the results from this method with results obtained by pneumatic nebulization (PN) ICP-AES after the wet-chemical decomposition of the same sample.From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 3, 2005, pp. 286–290.Original English Text Copyright © 2005 by Chen.This article was submitted by the author in English.     

Determination of zinc in marine/lacustrine sediments by graphite furnace atomic absorption spectrometry using Pd/Mg chemical modifier and slurry sampling

Effectiveness of Pd/Mg chemical modifier for the accurate direct determination of zinc in marine/lacustrine sediments by graphite furnace atomic absorption spectrometry (GF-AAS) using slurry samples was evaluated. A calibration curve prepared by aqueous zinc standard solution with addition of Pd/Mg chemical modifier is used to determine the zinc concentration in the sediment. The accuracy of the proposed method was confirmed using Certified Reference Materials, NMIJ CRM 7303-a (lacustrine sediment) from National Metrology Institute of Japan, National Institute of Advanced Industrial Science and Technology, Japan, and MESS-3 (marine sediment) and PACS-2 (marine sediment) from National Research Council, Canada. The analytical results obtained by employing Pd/Mg modifier are in good agreement with the certified values of all the reference sediment materials. Although for NRC MESS-3 an accurate determination of zinc is achieved even without the chemical modifier, the use of Pd/Mg chemical modifier is recommended as it leads to establishment of a reliable and accurate direct analytical method. One quantitative analysis takes less than 15 minutes after we obtain dried sediment samples, which is several tens of times faster than conventional analytical methods using acid digested sample solutions. The detection limits are 0.13?µg?g^?1 (213.9?nm) and 16?µg?g^?1 (307.6?nm), respectively, in sediment samples, when 40?mg of dried powdered samples are suspended in 20?mL of 0.1?mol?L^?1 nitric acid and a 10?µl portion of the slurry sample is measured. The precision of the proposed method is 8–15% (RSD).     

A new approach for determination of crustal and trace elements in airborne particulate matter

An ICP-OES procedure was developed for fast and accurate determination of various crustal (Al, Ca, Fe, Mg, Si) and trace elements (Ba, Cu, Mn, Na, K, Sr, Ti, Zn) in airborne particulate matter. The method is based on a preliminary treatment of the aerosol samples with a mixture of nitric acid and hydrogen peroxide at elevated temperature leading to a mineralization of the organic sampling substrate, dissolution of soluble material and homogeneous suspension of the remaining non-soluble fraction. After dilution the derived slurry solutions were measured using ICP-OES. The reproducibility of analysis given as the relative standard deviation (% RSD) varied between 3.2 and 6.8% for bulk constituents such as Al, Ca, Fe, Mg and Si whereas values ranging from 3.5 to 9.1% were obtained for trace metals present with distinctly lower abundance in PM10 (e.g. Ba, Cu, Mn, Sr, Zn). The limits of detection (LOD) calculated as three times the standard deviation (3σ) of the signal derived from filter blank samples ranged from approximately 1?ng?m^?3 (Sr) to 71?ng?m^?3(Ca). The developed procedure was evaluated by comparing the obtained results with the findings derived for the same set of aerosol samples analyzed using a microwave procedure for sample dissolution with subsequent ICP-OES analysis. Finally the developed procedure was applied for the analysis of crustal and trace elements in PM10 samples collected at an urban site (Getreidemarkt, Vienna) and a rural site (Hartberg, Styria), in Austria. The concentrations of the investigated crustal elements varied between some hundred ng?m^?3 and few µg?m^?3 with highest concentrations for Fe and Si, distinctly reduced concentrations ranging from some ng?m^?3 (Sr) to more than hundred ng?m^?3 (K) were found for trace elements. Observed PM10 concentrations were found to be in accordance to literature findings from urban sites in central Europe.     

Silica gel surface modified with sulfanilamide for selective solid-phase extraction of Cu(II), Zn(II) and Ni(II)

A new chelating matrix has been prepared by immobilising sulfanilamide (SA) on silica gel (SG) surface modified with 3-chloropropyltrimethoxysilane as a sorbent for the solid-phase extraction (SPE) Cu(II), Zn(II) and Ni(II). The determination of metal ions in aqueous solutions was carried out by inductively coupled plasma optical emission spectrometry (ICP-OES). Experimental conditions for effective sorption of trace levels of Cu(II), Zn(II) and Ni(II) were optimised with respect to different experimental parameters using the batch and column procedures. The presence of common coexisting ions does not affect the sorption capacities. The maximum sorption capacity of the sorbent at optimum conditions was found to be 34.91, 19.07 and 23.62 mg g^?1 for Cu(II), Zn(II) and Ni(II), respectively. The detection limit of the method defined by IUPAC was found to be 1.60, 0.50 and 0.61 µg L^?1 for Cu(II), Zn(II) and Ni(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was 4.0% (n = 8). The method was applied to the recovery of Cu(II), Zn(II) and Ni(II) from the certified reference material (GBW 08301, river sediment) and to the simultaneous determination of these cations in different water samples with satisfactory results.     

Selective back-extraction and preconcentration of zinc(II) from metal-1,3,5-triketone extracts prior to its determination by flame atomic absorption spectrometry

A simple back-extraction method was developed for the separation and preconcentration of trace levels of zinc from different matrices. Ethyl-2-(4-methoxybenzoyl)-3-(4-methoxyphenyl)-3-oxopropanoylcarbamate (EMPC) was used as a new complexing agent for the extraction of zinc(II) from the aqueous sample phase to the methyl isobutyl ketone (MIBK) phase as Zn(EMPC)₂ complexes. The Zn(II) can be selectively stripped with 1?mL of 0.5?mol?L^?1 HCl from Mⁿ⁺(EMPC)_n complexes [Ag(I), Al(III), Cd(II), Cr(III), Cu(II), Fe(II), Fe(III), Mn(II), Ni(II), Pb(II) and Pd(II)] which dissolved in MIBK phase. Some experimental parameters, which are important for the whole extraction process, including pH, sample volume, shaking time, amount of the EMPC reagent, amount of MIBK, ionic strength, and type of back-extractant were investigated. The recovery for Zn(II) was greater than 95%. The detection limit of the method was found to be 0.2?µg?L ^{? 1} and the relative standard deviation as 6.4%. The concentrations of Zn(II) in the certified reference materials (LGC6019 river water and NIST-1547 peach leaves) by the presented method were in good agreement with the certified values. The proposed method was succesfully applied to the determination of zinc in some natural waters, rice, hair, soil, and tea samples.     

Optimization of the Sample Preparation Procedure for the Determination of Trace Elements in Auricularia auricula by Inductively Coupled Plasma-Optical Emission Spectrometry

This study aimed to develop a precise and accurate method of sample preparation of Auricularia auricula for inductively coupled plasma-optical emission spectrometry-based trace element determination and to compare concentrations of seven trace elements (Mg, Fe, Mn, Zn, Ni, Cr, Sr) in six A. auricula samples belonging to three varieties with two cultivation substrates. Five sample preparation procedures, microwave-assisted digestion, nitric acid digestion with hot plate heating, nitric acid and perchloric acid digestion with hot plate heating, nitric acid digestion with ash content, and aqua regia digestion with ash content, were compared. The performance of the procedures was determined based on the precision and accuracy of the results and the limits of detection of the elements. The best results, with limits of detection of 0.60–6.60?ng?·?mL^?1 and recoveries for spiked samples between 93.80 and 105.00%, were found using nitric acid digestion with ash content. Six A. auricula samples were analyzed using the proposed procedure. Among the tested elements, the concentration of Fe was highest in all six A. auricula samples up to a maximum concentration of 284.83?µg?·?g^?1. The concentrations of Mn, Cu, and Ni increased in mixed stands (basswood, birch, and mongolica) compared with pine sawdust cultivation.     

Selective extraction and determination of Au(III) by first-derivative spectrophotometry

The selective extraction of Au(III) in the presence of Zn(II) by salting-out of 2-propanol was investigated. The salting-out effect increased partitioning between water and 2-propanol in the presence of sodium chloride in aqueous–organic mixtures. This is observed through the distribution coefficient, which increases with salt addition. First-derivative spectrophotometry, which eliminates interference from overlapping spectral bands, was used for the determination of trace Au(III) in the presence of Zn(II). Absorption spectra were recorded and the first-derivative spectra were obtained using Δλ?=?10?nm. The calibration graph was linear for 0.857–5.142?µg?mL^?1 and the detection limit was 0.038–8?µg?mL^?1. The proposed method has been successfully applied to the determination of trace Au(III) in synthetic mixtures and Algerian low gold ore solutions. The results agree with those obtained by atomic absorption spectroscopy and the recoveries were >98%. The relative standard deviations were in all instances less than 3%.     

Application of an ETV-ICP system for the determination of elements in human hair

When determining element contents in hair samples without sample digestion it is necessary to analyze large sample volumes in order to minimize problems of inhomogeneity of biological sample materials. Therefore an electrothermal vaporization system (ETV) is used for solid sample introduction into an inductively coupled plasma (ICP) for the determination of matrix and trace elements in hair. This paper concentrates on the instrumental aspects without time consuming sample preparation. The results obtained for optimization tests, ETV operating parameters and ICP operating parameters, are shown and discussed. Standard additions are used for calibration for the determination of Zn, Mg, and Mn in human hair. Studies including reproducibility and detection limits for chosen elements have been carried out on certified reference materials (CRMs). The determination of reproducibility (relative standard deviation (RSD) of n = 10) and detection limits (DLs) of Zn (RSD < 8.5%, DL < 0.8 μ g⁻¹), Mn (RSD < 14.1%, DL < 0.3 μ g⁻¹), and Mg (RSD < 7.4%, DL < 6.6 μ g⁻¹) are satisfactory. The concentration values found show good agreement with the corresponding certified values. Further sample preparation steps, including hair sampling, washing procedure and homogenization for hair, relating to measurements of real hair samples are described.     

Acid predigestion as a slurry pretreatment for the determination of Ca, Cu, K, Mg, Na and Zn in human scalp hair by flame atomic absorption/emission spectrometry with a high-performance nebulizer

A comparison was carried out between the use of wetting agents, Viscalex HV30 or glycerol, and an acid predigestion of the slurry for the determination of major metals (Ca, Cu, K, Mg, Na and Zn) in human scalp hair by FAAS/FAES with a high-performance nebulizer. Human scalp hair was pulverized in a Zr vibrating ball mill over a period of 20 min (mean particle size about 0.8 μm measured by laser diffraction). The use of wetting agents was only found adequate for dilute slurries; thus, Viscalex HV30 can be proposed for the determination of Zn in scalp hair slurries (relative atomization efficiency close to unit). For all cases, the use of acidified slurries with nitric acid at a concentration of 1.0% offers adequate analytical performance: LODs of 5.0, 3.5, 3.1 and 20.0 mg kg^–1 for Ca, Cu, Fe and K, respectively, and 1.7, 0.6 and 3.5 μg kg^–1 for Mg, Na and Zn. The repeatability of the overall method (n = 11), acid predigestion-slurry pretreatment and FAAS/FAES determination expressed as RSD (%), was between 8.7 for Zn and 18.6 for K. The developed methods were applied to 25 human scalp hair samples from healthy adults.     

Direct inductively coupled plasma-atomic emission spectrometry analysis of trace elements in muscle tissues of hairtail using electrothermal vaporization with slurry sampling

A procedure for direct determination of trace elements in muscle tissue of hairtail was developed using inductively coupled plasma-atomic emission spectrometry and electrothermal vaporization with slurry sampling. Due to use of polytetrafluoroethylene as the chemical modifier, the vaporization behaviors of analytes from the slurry and the aqueous standard solutions were very similar. In this case, the aqueous standards could be used for the calibration of slurry samples. The main factors influencing this method were studied systematically. The detection limits for Cr, Ni, Zn, Cd, and Pb were 3.1, 10.5, 176, 6.9, and 83 ng/mL, respectively, and the relative standard deviations were less than 10%. The proposed method was applied to the determination of trace Cr, Ni, Zn, Cd, and Pb in hairtail samples with satisfactory accuracy and precision. A certified reference material of mussel (GBW 08571) was analyzed, and good agreement was obtained between the results from the proposed method and certificate values.     

Direct determination of trace copper and chromium in silicon nitride by fluorinating electrothermal vaporization inductively coupled plasma atomic emission spectrometry with the slurry sampling technique

A method has been developed for the determination of trace impurities in silicon nitride (Si₃N₄) powders by fluorination assisted electrothermal vaporization (ETV) /ICP-AES using the slurry sampling technique. Polytetrafluoroethylene (PTFE) emulsion as a fluorinating reagent not only effectively destroys the skeleton of Si₃N₄, but also carries out selective volatilization between the impurity elements (Cu, Cr) and the matrix (Si). The experimental parameters influencing fluorination reactions were optimized. The detection limits for Cu and Cr are 1.05 ng/mL ( Cu) and 1.58 ng/mL (Cr), the RSDs are in the range of 1.9–4.2%. The proposed method has been applied to the determination of Cu and Cr in Si₃N₄ ceramic powders. The analytical results were compared with those obtained by independent methods.     

Voltammetric Quantification of Zn and Cu,Together with Hg and Pb,Based on a Gold Microwire Electrode,in a Wider Spectrum of Surface Waters

The simultaneous determination of Zn and Cu by anodic stripping voltammetry (ASV) is prone to errors due to the formation of Cu‐Zn intermetallic compounds. The main aim of this work was to study the possibility of simultaneous determination of Zn and Cu, together with Hg and Pb, using a mercury‐free solid gold microwire electrode. The multi‐element detection was carried out by differential pulse anodic stripping voltammetry (DPASV), in a chloride medium (0.5 M NaCl) under moderate acid conditions (HCl 1.0 mM) in the presence of oxygen, where the gold microwire electrode was used as stationary or vibrating working electrode during the deposition step. Under these conditions, no formation of Cu‐Zn intermetallic compounds were found for concentrations usually determined in surface waters. In addition, quantification of Zn and Cu, together with Hg and Pb, can be performed in a wide range of concentrations (about two orders of magnitude) using the same sample, in a very short period of time. The detection limits for Cu, Hg, Pb and Zn, using a vibrating electrode and 30 s of deposition time, were 0.2 µg L^?1 for Hg, 0.3 µg L^?1 for Pb and 0.4 µg L^?1 for Zn and Cu, respectively. The proposed DPASV methods were successfully applied to the determination of Cu, Hg, Pb, and Zn in a certified reference fresh water, river, tap and coastal sea waters. These results proved the applicability and versatility of the proposed methods for the analysis of different water matrices and showed that a gold microwire electrode is a suitable choice to determine simultaneously Zn and Cu.     

Novel Chelating Resin for Solid-Phase Extraction of Metals in Certified Reference Materials and Waters

A new chelating resin, poly(diacetonitrile methacrylamide-co-divinylbenzene-co-vinylimidazole), was synthesized and characterized by infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, and elemental analysis. The novel resin was used for the first time as a chelating adsorbent for the preconcentration of Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn from various samples by flame atomic absorption spectrometry. The adsorption capacities of the resin were 29.3, 31.6, 29.3, 27.3, 35.5, 31.7, 39.8, and 32.3?mg?g^?1 for Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn, respectively. The detection limits of the metal ions were from 0.42 to 3.21?µg?L^?1. A preconcentration factor of 30 for all metal ions was obtained. The precision of the method as the relative standard deviation was less than or equal to 2.6%. The described method was validated with certified reference materials and fortified real samples. The method was used for the determination of the analytes in well water and wastewater.     

Determination of Heavy Metal Content in Wild-Edible Mushroom from Jordan

The heavy metal content was investigated for six mushroom species native to Jordan. Metal (Cu, Pb, Cd, Fe, Zn, Mn, Ni, and Co) content in soil substrate and their relation to metal concentrations in mushroom and underlying soil were determined by flame and graphite furnace atomic absorption spectrometry. Mushroom species and soil were collected from different places in Jordan. The highest Cu level was 51.84 µg g^?1 for the species Lepista nuda; whereas, the lowest Cu level was found to be 18.51 µg g^?1 in Calvatia utriformis. Among the wild mushrooms, the highest Pb level was found as 4.81 µg g^?1 in Bovista plumbea, whereas the lowest Pb concentration was 2.01 µg g^?1 in Calvatia utriformis. The highest Cd level was determined as 1.9 µg g^?1 for Lepista nuda, whereas the lowest Cd level was 0.58 µg g^?1 for the species of Polyporus frondosus. The highest Zn level was 58.77 µg g^?1 for the species of Lepista nuda and the lowest Zn concentration was found 35.98 µg g^?1 in Calvatia utriformis. The highest Fe level was found as 317 µg g^?1 in Lepista nuda, whereas the lowest Fe concentration was 211.7 µg g^?1 in Calvatia utriformis. The highest Mn content was 36.55 µg g^?1 for Russula delica, whereas the lowest Mn level was 24.5 µg g^?1 for the species Bovista plumbea. The highest Ni content was found as 12.65 µg g^?1 for Russula delica, whereas the lowest Ni level was 0.17 µg g^?1 for Bovista plumbea. The highest Co content in the tested mushrooms was found as 3.5 µg g^?1 for the species of Agaricus bisporus, whereas the lowest Co level was 0.85 µg g^?1 for Polyporus frondosus. The results indicated that, in general, heavy metal contents in all mushroom species were lower than the underlying soil substrates except for some mushroom species.