Investigation of copper oxide impregnants prepared from various precursors for respirator carbons

Copper oxide impregnated activated carbon was prepared by three methods and studied as a respirator carbon. Using techniques such as dynamic flow testing, X-ray diffraction (XRD), thermal analysis, scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX), copper oxide impregnants, derived from different sources such as basic copper carbonate (Cu₂CO₃(OH)₂), copper nitrate (Cu(NO₃)₂) and copper chloride (CuCl₂) reacted with sodium hydroxide (NaOH), have been studied. Dynamic flow tests performed using sulfur dioxide (SO₂), ammonia (NH₃) and hydrogen cyanide (HCN) challenge gases allow the determination of the stoichiometric ratio of reaction (SRR) between challenge gas and impregnant. Thermal gravimetric analysis experiments showed that an inert heating environment was required when thermally decomposing the Cu(NO₃)₂ impregnant to CuO to avoid damaging the activated carbon substrate. SEM has been used to investigate dispersal and particle size of the impregnant on the activated carbon. XRD permits the identification of crystalline and amorphous phases as well as the grain size of the impregnant. XRD analysis of samples before and after exposure to SO₂ has allowed the active impregnant in SO₂ adsorption to be identified. The relationship between SRR, impregnant loading and grain size is discussed. Methods to improve impregnant distribution are presented and their impact discussed.     

Complexes of HNO3 and NO3 - with NO2 and N2O4, and their potential role in atmospheric HONO formation

Calculations were performed to determine the structures, energetics, and spectroscopy of the atmospherically relevant complexes (HNO(3)).(NO(2)), (HNO(3)).(N(2)O(4)), (NO(3)(-)).(NO(2)), and (NO(3)(-)).(N(2)O(4)). The binding energies indicate that three of the four complexes are quite stable, with the most stable (NO(3)(-)).(N(2)O(4)) possessing binding energy of almost -14 kcal mol(-1). Vibrational frequencies were calculated for use in detecting the complexes by infrared and Raman spectroscopy. An ATR-FTIR experiment showed features at 1632 and 1602 cm(-1) that are attributed to NO(2) complexed to NO(3)(-) and HNO(3), respectively. The electronic states of (HNO(3)).(N(2)O(4)) and (NO(3)(-)).(N(2)O(4)) were investigated using an excited state method and it was determined that both complexes possess one low-lying excited state that is accessible through absorption of visible radiation. Evidence for the existence of (NO(3)(-)).(N(2)O(4)) was obtained from UV/vis absorption spectra of N(2)O(4) in concentrated HNO(3), which show a band at 320 nm that is blue shifted by 20 nm relative to what is observed for N(2)O(4) dissolved in organic solvents. Finally, hydrogen transfer reactions within the (HNO(3)).(NO(2)) and (HNO(3)).(N(2)O(4)) complexes leading to the formation of HONO, were investigated. In both systems the calculated potential profiles rule out a thermal mechanism, but indicate the reaction could take place following the absorption of visible radiation. We propose that these complexes are potentially important in the thermal and photochemical production of HONO observed in previous laboratory and field studies.     

Studies of the equilibrium and thermodynamics of the adsorption of Cu(2+) onto as-produced and modified carbon nanotubes

This study evaluates the Cu(2+) adsorption efficiency of as-produced carbon nanotubes (CNTs) and those modified by HNO(3) and NaOCl. The surface area, pH(pzc), pore volume, FTIR analyses, and average pore size of CNTs were determined to compare the differences between nanotubes before and after HNO(3) and NaOCl modification. The HNO(3) and NaOCl modifications increased the pore volume and the average pore size of CNTs; in contrast, the pH(pzc) was decreased. The modification processes produced some functional groups. The adsorption capacity of Cu(2+) on as-produced and modified CNTs increased with the pH and temperature; however, the effects of the ionic strength on the adsorption of Cu(2+) on as-produced and modified CNTs were negligible. The linear correlation coefficients of Langmuir and Freundlich isotherms were obtained and the results revealed that the Langmuir isotherm fitted the experimental results better than did the Freundlich isotherm. The adsorption capacity of Cu(2+) followed the order NaOCl-modified CNTs > HNO(3)-modified CNTs > as-produced CNTs. Changes in the free energy of adsorption (DeltaG(o)), enthalpy (DeltaH(o)), and entropy (DeltaS(o)) were determined. All DeltaG(o) values were negative; the DeltaH(o) values of as-produced, HNO(3)-modified, and NaOCl-modified CNTs were 10.84, 17.08, and 67.77 kJ/mol and the DeltaS(o) values were 96.89, 122.88, and 319.76 J/mol K, respectively.     

Acid/Base-treated activated carbons: characterization of functional groups and metal adsorptive properties

Surface modification of activated carbons by various physicochemical methods directs an attractive approach for improvement of heavy metal uptake from aqueous solutions. Activated carbons were modified with HCl and HNO3 optionally followed by NaOH. The effects of surface modifications on the properties of the carbons were studied by the specific surface area, carbon pH, and total acidity capacity as well as by scanning electron microscopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy. The modifications bring about substantial variation in the chemical properties whereas the physical properties remain nearly unchanged. NaOH causes an increase in the content of hydroxyl groups, while the HCl treatment results in an increase in the amount of single-bonded oxygen functional groups such as phenols, ethers, and lactones. The HNO3 modification generates a large number of surface functional groups such as carbonyl, carboxyl, and nitrate groups. The HNO3 modification significantly increases the copper adsorption, while the HCl treatment slightly reduces the copper uptake. Most of the copper ions are adsorbed rapidly in the first 2 h; the adsorption equilibrium is established in around 8 h. An intraparticle diffusion model successfully describes the kinetics of copper adsorption onto the carbons.     

Construction of 0D to 3D cadmium complexes from different pyridyl diimide ligands

Four semirigid ditopic ligands, N,N'-bis(3-pyridylmethyl)-pyromellitic diimide (L(1)), N,N'-bis(4-pyridylmethyl)-pyromellitic diimide (L(2)), N,N'-bis(3-pyridylmethyl)-naphthalene diimide (L(3)), and N,N'-bis(4-pyridylmethyl)-naphthalene diimide (L(4)), reacted with Cd(NO(3))(2) to result in four cadmium(II) complexes, namely, {[Cd(2)(L(1))(2)(NO(3))(4)(CH(3)OH)(4)]·H(2)O} (1), [Cd(L(2))(NO(3))(2)(CH(3)OH)(2)·Cd(2)(L(2))(3)(NO(3))(4)]·{4(HCCl(3))·2H(2)O}(n) (2), {[Cd(L(3))(2)(NO(3))(2)]}(n) (3), and {[Cd(L(4))(2)(NO(3))(2)]·2(CHCl(3))}(n) (4). These complexes have been characterized by elemental analyses, powder X-ray diffraction, thermogravimetric (TG) analyses, IR spectroscopy, and single-crystal X-ray diffraction. Structural analyses show that four types of structures are formed: (1) a discrete M(2)L(2) ring with two Cd ions and two cis-L(1) ligands comprising a zero-dimensional molecular rectangle (0D), (2) an unusual zigzag linear chain and a one-dimensional ladder existing simultaneously in the crystal lattice (1D), (3) a two-dimensional network of the (4,4) net structure (2D), and (4) an unusual chiral three-dimensional framework with 5-fold interpenetrating diamond (dia) topology (3D). In these complexes, the ligands exhibit different coordination modes and construct various architectures by bridging Cd(NO(3))(2) inorganic building blocks. These results suggest that structural diversity of the complexes is tunable by ligand modifications, that is, varying the ligand spacer bulkiness or substituent position of terminal group. Furthermore, gas adsorption measurements indicate that 4 possesses moderate CO(2) uptake and some adsorption selectivity for CO(2) over N(2).     

Low-temperature catalytic adsorption of NO on activated carbon materials

The catalytic adsorption of NO on activated carbon materials provides an appropriated alternative for the control of low-concentration emissions of this air pollutant. The surface complexes formed upon NO adsorption at 30 degrees C were studied by X-ray photoelectron spectroscopy (XPS) and temperature-programmed desorption (TPD). The effects of the addition of O2 and the presence of copper as a catalyst were studied. Copper assisted the oxygen transfer to the carbon matrix. For the Cu-impregnated carbon sample, the presence of O2 favored NO adsorption by increasing the breakthrough time, the adsorption capacity, and the formation of nitrogen and oxygen complexes of higher thermal stabilities, which mainly desorbed as NO and CO2.     

Uranium dioxide in ionic liquid with a tri-n-butylphosphate-HNO3 complex--dissolution and coordination environment

Uranium dioxide can be dissolved directly in an imidazolium-based ionic liquid (IL) at room temperature with a tri-n-butylphosphate(TBP)-HNO(3) complex. The dissolution process follows pseudo first-order kinetics initially. Raman spectroscopic studies show the dissolved uranyl ions are coordinated with TBP in the IL phase with a molar ratio of (UO(2))(2+) : TBP = 1 : 2. The dissolved uranyl species can be effectively transferred to a supercritical fluid carbon dioxide (sc-CO(2)) phase. No aqueous phase is formed in either the IL dissolution or the supercritical fluid extraction process. Absorption spectra of the extracted uranyl species in the sc-CO(2) phase suggests the presence of a UO(2)(TBP)(2)(NO(3))(2) and HNO(3) adduct probably of the form UO(2)(TBP)(2)(NO(3))(2)·HNO(3). The adduct dissociates in a water-dodecane trap solution during pressure reduction resulting in UO(2)(TBP)(2)(NO(3))(2) collected in the dodecane phase.     

Modeling substrate- and inhibitor-bound forms of liver alcohol dehydrogenase: chemistry of mononuclear nitrogen/sulfur-ligated zinc alcohol,formamide, and sulfoxide complexes

Using a mixed nitrogen/sulfur ligand possessing a single internal hydrogen bond donor (N,N-bis-2-(methylthio)ethyl-N-(6-amino-2-pyridylmethyl)amine (bmapa)), we prepared and structurally and spectroscopically characterized a series of zinc complexes possessing a single alcohol ([(bmapa)Zn(MeOH)](ClO(4))(2) (1)), formamide ([(bmapa)Zn(DMF)](ClO(4))(2) (3), [(bmapa)Zn(NMF)](ClO(4))(2) (4)), or sulfoxide ([(bmapa)Zn(DMSO)](ClO(4))(2) (7), [(bmapa)Zn(TMSO)](ClO(4))(2) (8)) ligand. X-ray crystallographic characterization was obtained for 1.MeOH, 3, 4, 7.DMSO, and 8. To enable studies of the influence of the single hydrogen bond donor amino group of the bmapa ligand on the chemistry of zinc/neutral oxygen donor binding interactions, analogous alcohol ([(bmpa)Zn(MeOH)](ClO(4))(2) (2)), formamide ([(bmpa)Zn(DMF)](ClO(4))(2) (5), [(bmpa)Zn(NMF)](ClO(4))(2) (6)), and sulfoxide ([(bmpa)Zn(DMSO)](ClO(4))(2) (9), [(bmpa)Zn(TMSO)](ClO(4))(2) (10)) complexes of the bmpa (N,N-bis-2-(methylthio)ethyl-N-(2-pyridylmethyl)amine) ligand system were generated and characterized. Of these, 2, 5, 6, and 9.2DMSO were characterized by X-ray crystallography. Solution spectroscopic methods ((1)H and (13)C NMR, FTIR) were utilized to examine the formamide binding properties of 3-6 in CH(3)CN and CH(3)NO(2) solutions. Conclusions derived from this work include the following: (1) the increased donicity of formamide and sulfoxide donors (versus alcohols) makes these competitive ligands for a cationic N/S-ligated zinc center, even in alcohol solution, (2) the inclusion of a single internal hydrogen bond donor, characterized by a heteroatom distance of approximately 2.80-2.95 A, produces subtle structural perturbations in N/S-ligated zinc alcohol, formamide, or sulfoxide complexes, (3) the heteroatom distance of a secondary hydrogen-bonding interaction involving the oxygen atom of a zinc-coordinated alcohol, formamide, and sulfoxide ligand is reduced with increasing donicity of the exogenous ligand, and (4) formamide displacement on a N/S-ligated zinc center is rapid, regardless of the presence of an internal hydrogen bond donor. These results provide initial insight into the chemical factors governing the binding of a neutral oxygen donor to a N/S-ligated zinc center.     

Uptake of HNO3 on hexane and aviation kerosene soots

The uptake of HNO(3) on aviation kerosene (TC-1) soot was measured as a function of temperature (253-295 K) and the partial pressure of HNO(3), and the uptake of HNO(3) on hexane soot was studied at 295 K and over a limited partial pressure of HNO(3). The HNO(3) uptake was mostly reversible and did not release measurable amounts of gas-phase products such as HONO, NO(3), NO(2) or N(2)O(5). The heat of adsorption of HNO(3) on soot was dependent on the surface coverage. The isosteric heats of adsorption, Delta(0)H(isosteric), were determined as a function of coverage. Delta(0)H(isosteric) values were in the range -16 to -13 kcal mol(-1). The heats of adsorption decrease with increasing coverage. The adsorption data were fit to Freundlich and to Langmuir-Freundlich isotherms. The heterogeneity parameter values were close to 0.5, which suggested that a HNO(3) molecule can occupy two sites on the surface with or without being dissociated and that the soot surface could be nonuniform. Surface FTIR studies on the interaction of soot with HNO(3) did not reveal formation of any minor product such as organic nitrate or nitro compound on the soot surface. Using our measured coverage, we calculate that the partitioning of gas-phase nitric acid to black carbon aerosol is not a significant loss process of HNO(3) in the atmosphere.     

Intermolecular activation of hydrocarbon C-H bonds under ambient conditions by 16-electron neopentylidene and benzyne complexes of molybdenum

CpMo(NO)(CH(2)CMe(3))(2) (1), a complex with alpha-agostic C-H.Mo interactions, evolves neopentane in neat hydrocarbon solutions at room temperature and forms the transient 16-electron alkylidene complex, CpMo(NO)(=CHCMe(3)), which subsequently activates solvent C-H bonds. Thus, it reacts with tetramethylsilane or mesitylene to form CpMo(NO)(CH(2)CMe(3))(CH(2)SiMe(3)) (2) or CpMo(NO)(CH(2)CMe(3))(eta(2)-CH(2)C(6)H(3)-3,5-Me(2)) (3), respectively, in nearly quantitative yields. Under identical conditions, 1 in p-xylene generates a mixture of sp(2) and sp(3) C-H bond activation products, namely CpMo(NO)(CH(2)CMe(3))(C(6)H(3)-2,5-Me(2)) (4, 73%) and CpMo(NO)(CH(2)CMe(3))(eta(2)-CH(2)C(6)H(4)-4-Me) (5, 27%). In benzene at room temperature, 1 transforms to a mixture of CpMo(NO)(CH(2)CMe(3))(C(6)H(5)) (6) and CpMo(NO)(C(6)H(5))(2) (7) in a sequential manner. Most interestingly, the thermal activation of 6 at ambient temperatures gives rise to two parallel modes of reactivity involving either the elimination of benzene and formation of CpMo(NO)(=CHCMe(3)) or the elimination of neopentane and formation of the benzyne complex, CpMo(NO)(eta(2)-C(6)H(4)). In pyridine, these intermediates are trapped as the isolable 18-electron adducts, CpMo(NO)(=CHCMe(3))(NC(5)H(5)) (8) and CpMo(NO)(eta(2)-C(6)H(4))(NC(5)H(5)) (9), and, in hydrocarbon solvents, they effect the intermolecular activation of aliphatic C-H bonds at room temperature to generate mixtures of neopentyl- and phenyl-containing derivatives. However, the distribution of products resulting from the hydrocarbon activations is dependent on the nature of the solvent, probably due to solvation effects and the presence of sigma- or pi-hydrocarbon complexes on the reaction coordinates of the alkylidene and the benzyne intermediates. The results of DFT calculations on these processes in the gas phase support the existence of such hydrocarbon complexes and indicate that better agreement with experimental observations is obtained when the actual neopentyl ligand rather than the simpler methyl ligand is used in the model complexes.     

Synthesis, structure, and complexation of a large 28-mer macrocycle containing two binding sites for either anions or metal ions

The "one-pot" synthesis and characterization of a large 28-mer macrocycle (H(4)L(2)) with oxamido units capable of complexing guest ions through oxygen or nitrogen donor atoms is reported. Single-crystal structure determination of H(8)L(2)(NO(3))(4) and (Cu(2)[H(2)L(2)](H(2)O)(2))(NO(3))(2) demonstrated that the macrocycle contains two sites capable of complexing two nitrate anions or two copper(II) ions, involving a large structural reorganization in the conformation of the macrocyclic framework on coordination of the copper(II) ions when compared to the nitrate. Electrochemical and magnetic susceptibility measurements on the dinuclear Cu(II) complex and the related mononuclear and trinuclear Cu(II) complexes derived from the related 14-mer macrocycle were carried out and illustrate the role of the oxamido groups in mediating metal-metal interaction and delocalization.     

Heterogeneous conversion of calcite aerosol by nitric acid

The reaction of nitric acid with calcite aerosol at varying relative humidities has been studied under suspended particle conditions in an atmospheric reaction chamber using infrared absorption spectroscopy. The reactant concentration in the chamber, as well as the appearance of gas phase products and surface adsorbed species, was spectroscopically monitored before and after mixing with CaCO(3) (calcite) particles. The interaction with HNO(3) was found to lead to gas phase CO(2) evolution and increased water uptake due to heterogeneous conversion of the carbonate to particulate nitrate. The reaction was enhanced as the relative humidity of the system was increased, especially at relative humidities above the reported deliquescence point of particulate Ca(NO(3))(2). The measured reaction extent demonstrates that the total calcite particulate mass is available for reaction with HNO(3) and the conversion process is not limited to the particle surface. The spectroscopy of the surface formed nitrate suggests a highly concentrated solution environment with a significant degree of ion pairing. The implications of the HNO(3) loss and the formation of the particulate nitrate product for atmospheric chemistry are discussed.     

Features of the thermodynamics of two-phase distribution reactions of americium(III) and europium(III) nitrates into solutions of 2,6-bis[(bis(2-ethylhexyl)phosphino)methyl]pyridine N,P,P'-trioxide

New bifunctional and trifunctional organophosphorus ligands, 2-[(bis(2-ethylhexyl)phosphino)methyl]pyridine N,P-dioxide, DEH(MNOPO), and 2,6-bis[(bis(2-ethylhexyl)phosphino)methyl]pyridine N,P,P'-trioxide, TEH(NOPOPO), have been synthesized. In contrast with previously reported phenyl derivatives, the increased solubility of these ligands in normal paraffinic hydrocarbon solvents make them attractive reagents for actinide partitioning. While the bifunctional reagent DEH(MNOPO) interacts with Eu(3+) and Am(3+) comparatively weakly, the trifunctional TEH(NOPOPO) exhibits moderate to high ability to transfer the trisnitrato complexes of these ions into n-dodecane from acidic aqueous solutions. We report here the details of TEH(NOPOPO) and DEH(MNOPO) preparation and of their ability to extract HNO(3), Am(NO(3))(3), and Eu(NO(3))(3) into paraffinic hydrocarbons. The trifunctional TEH(NOPOPO) can extract up to two molecules of HNO(3). The dominant extracted species for both Am(NO(3))(3) and Eu(NO(3))(3) has two TEH(NOPOPO) ligands associated over the range of temperatures 10-40 degrees C. From the variation in the equilibrium coefficients for the phase transfer reactions as a function of temperature, we have calculated the enthalpies and entropies for extraction of HNO(3), Am(NO(3))(3), and Eu(NO(3))(3) into n-dodecane. Each metal nitrate is transferred into the organic phase in an exothermic process but opposed by an unfavorable (negative) entropy. The thermodynamic data are interpreted to indicate that the pyridine N-oxide is apparently a significantly weaker donor group for these metal ions than the phosphine oxides.     

New heterometallic coordination polymers self-assembled from copper(II) nitrate and (diamine)Pt(II)(pyridinecarboxylates)(2)

One-dimensional (1-D), two-dimensional (2-D), and three-dimensional (3-D) coordination polymers were prepared by self-assembly of binary metal complex systems, copper(II) nitrate and (en)Pt(II)(nic)(2) or (dmpda)Pt(II)(isonic)(2) (en = ethylenediamine, dmpda = 2,2'-dimethyl-1,3-propanediamine, nic = nicotinate, and isonic = isonicotinate), in aqueous solutions. Equimolar reactions of copper(II) nitrate with (dmpda)Pt(II)(isonic)(2) and (en)Pt(II)(nic)(2) resulted in 1-D ([(dmpda)Pt(isonic)(2)Cu(OH(2))(3)](NO(3))(2))(n)() (1) and 2-D ([(en)Pt(nic)(2)Cu(OH(2))](NO(3))(2))(n) (2), respectively, but the reaction of (en)Pt(II)(nic)(2) with excess copper(II) nitrate gave 3-D ([((en)Pt(nic)(2))(3)Cu(5)(OH)(2)(OH(2))(6)](NO(3))(8))(n) (3). The local structure of crystal 1 has a mononuclear copper unit, 2 has a dinuclear copper unit with a Cu-Cu distance of 2.659(5) A, and 3 has a pentanuclear copper unit. The methyl groups of the dmpda ligand are located in the space between two isonicotinate ligands of 1, which is presumed to be an important factor to determine the final structure of the crystal formed by self-assembly. Magnetic behaviors of crystals 1-3 examined in the temperature range of 4-300 K appear to be governed by the local structures around the copper(II) ions and do not indicate any significant long-range magnetic exchange interactions along the polymeric chain.     

The heterogeneous chemical kinetics of NO3 on atmospheric mineral dust surrogates

Uptake experiments of NO3 on mineral dust powder were carried out under continuous molecular flow conditions at 298 +/- 2 K using the thermal decomposition of N2O5 as NO3 source. In situ laser detection using resonance enhanced multiphoton ionization (REMPI) to specifically detect NO2 and NO in the presence of N2O5, NO3 and HNO3 was employed in addition to beam-sampling mass spectrometry. At [NO3] = (7.0 +/- 1.0) x 10(11) cm(-3) we found a steady state uptake coefficient gamma(ss) ranging from (3.4 +/- 1.6) x 10(-2) for natural limestone to (0.12 +/- 0.08) for Saharan Dust with gamma(ss) decreasing as [NO3] increased. NO3 adsorbed on mineral dust leads to uptake of NO2 in an Eley-Rideal mechanism that usually is not taken up in the absence of NO3. The disappearance of NO3 was in part accompanied by the formation of N2O5 and HNO3 in the presence of NO2. NO3 uptake performed on small amounts of Kaolinite and CaCO3 leads to formation of some N2O5 according to NO((3ads)) + NO(2(g)) --> N2O(5(ads)) --> N2O(5(g)). Slow formation of gas phase HNO3 on Kaolinite, CaCO3, Arizona Test Dust and natural limestone has also been observed and is clearly related to the presence of adsorbed water involved in the heterogeneous hydrolysis of N2O(5(ads)).     

Polymeric networks of copper(II) using succinate and aromatic N-N donor ligands: synthesis, crystal structure, magnetic behaviour and the effect of weak interactions on their crystal packing

Four succinato-bridged complexes of copper(II) have been synthesized. Complex 1, [Cu(2)(mu-OH(2))(2)L(bpy)(2)(NO(3))(2)](n) and 2, [Cu(2)(mu-OH(2))(2)L(phen)(2)(NO(3))(2)](n)(bpy = 2,2[prime or minute]-bipyridine; phen = 1,10-phenanthroline and LH(2)= succinic acid) exhibit 1D coordination polymer structures where both the nitrate ions are directly linked to the copper(ii) producing synthons in a 2D sheet. A novel 2D grid-like network, ([Cu(4)L(2)(bpy)(4)(H(2)O)(2)](ClO(4))(4)(H(2)O))n3, is obtained upon changing the nitrate by perchlorate anion in complex 1, where the channels are occupied by the anions. On changing the nitrate by tetrafluoroborate anion in complex 2, a novel octanuclear complex, [Cu(8)L(4)(phen)(12)](BF(4))(8).8H(2)O 4, is isolated. The coligand bpy and phen in these complexes show face-to-face (in 1,2,3,4) or edge-to-face (in 4 )pi-pi interactions forming the multidimensional supramolecular architectures. Interestingly, the appearance of edge-to-face pi-pi interactions in complex facilitates the formation of discrete octanuclear entities. Variable-temperature (300-2 K) magnetic measurements of complexes have been done. Complexes 1 and 2 show very weak antiferromagnetic (OOC-CH(2)-CH(2)-COO) and ferromagnetic coupling (mu-H(2)O). Complex 3 also shows antiferromagnetic (syn-syn mu-OCO), and ferromagnetic coupling (mu-O of the -COO group). Complex 4 with two types (syn-syn and syn-anti) of binding modes of the carboxylate group shows strong antiferromagnetic interaction.     

An isomorphous series of cubic, copper-based triazolyl isophthalate MOFs: linker substitution and adsorption properties

An isomorphous series of 10 microporous copper-based metal-organic frameworks (MOFs) with the general formulas (∞)(3)[{Cu(3)(μ(3)-OH)(X)}(4){Cu(2)(H(2)O)(2)}(3)(H-R-trz-ia)(12)] (R = H, CH(3), Ph; X(2-) = SO(4)(2-), SeO(4)(2-), 2 NO(3)(2-) (1-8)) and (∞)(3)[{Cu(3)(μ(3)-OH)(X)}(8){Cu(2)(H(2)O)(2)}(6)(H-3py-trz-ia)(24)Cu(6)]X(3) (R = 3py; X(2-) = SO(4)(2-), SeO(4)(2-) (9, 10)) is presented together with the closely related compounds (∞)(3)[Cu(6)(μ(4)-O)(μ(3)-OH)(2)(H-Metrz-ia)(4)][Cu(H(2)O)(6)](NO(3))(2)·10H(2)O (11) and (∞)(3)[Cu(2)(H-3py-trz-ia)(2)(H(2)O)(3)] (12(Cu)), which are obtained under similar reaction conditions. The porosity of the series of cubic MOFs with twf-d topology reaches up to 66%. While the diameters of the spherical pores remain unaffected, adsorption measurements show that the pore volume can be fine-tuned by the substituents of the triazolyl isophthalate ligand and choice of the respective copper salt, that is, copper sulfate, selenate, or nitrate.     

A family of 13 tetranuclear zinc(II)-lanthanide(III) complexes of a [3+3] Schiff-base macrocycle derived from 1,4-diformyl-2,3-dihydroxybenzene

A family of thirteen tetranuclear heterometallic zinc(II)-lanthanide(III) complexes of the hexa-imine macrocycle (L(Pr))(6-), with general formula Zn(II)(3)Ln(III)(L(Pr))(NO(3))(3)·xsolvents (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm or Yb), were prepared in a one-pot synthesis using a 3:1:3:3 reaction of zinc(II) acetate, the appropriate lanthanide(III) nitrate, the dialdehyde 1,4-diformyl-2,3-dihydroxybenzene (H(2)L(1)) and 1,3-diaminopropane. A hexanuclear homometallic zinc(II) macrocyclic complex [Zn(6)(L(Pr))(OAc)(5)(OH)(H(2)O)]·3H(2)O was obtained using a 2:0:1:1 ratio of the same reagents. A control experiment using a 1:0:1:1 ratio failed to generate the lanthanide-free [Zn(3)(L(Pr))] macrocyclic complex. The reaction of H(2)L(1) and zinc(II) acetate in a 1:1 ratio yielded the pentanuclear homometallic complex of the dialdehyde H(2)L(1), [Zn(5)(L(1))(5)(H(2)O)(6)]·3H(2)O. An X-ray crystal structure determination revealed [Zn(3)(II)Pr(III)(L(Pr))(NO(3))(2)(DMF)(3)](NO(3))·0.9DMF has the large ten-coordinate lanthanide(III) ion bound in the central O(6) site with two bidentate nitrate anions completing the O(10) coordination sphere. The three square pyramidal zinc(II) ions are in the outer N(2)O(2) sites with a fifth donor from DMF. Measurement of the magnetic properties of [Zn(II)(3)Dy(III)(L(Pr))(NO(3))(3)(MeOH)(3)]·4H(2)O with a weak external dc field showed that it has a frequency-dependent out-of-phase component of ac susceptibility, indicative of slow relaxation of the magnetization (SMM behaviour). Likewise, the Er and Yb analogues are field-induced SMMs; the latter is only the second example of a Yb-based SMM. The neodymium, ytterbium and erbium complexes are luminescent in the solid phase, but only the ytterbium and neodymium complexes show strong lanthanide-centred luminescence in DMF solution.     

Trace enrichment with activated carbon and determination of trace metals in high-purity zinc and zinc(II) nitrate

A method is described for the enrichment and determination of trace metals such as Ag, Bi, Cu, Co, Cd, In, Pb, Ni, Tl, Fe and Hg, present as impurities in high-purity zinc and zinc(II) nitrate. When the sample solution, after addition of potassium ethyl xanthate, is filtered through a small filter paper coated with 50 mg of activated carbon, the trace elements are quantitatively adsorbed on the carbon. The trace elements (with the exception of Hg) are dissolved off with nitric acid and determined by atomic-absorption or emission spectrometry. Mercury is evaporated at 650 degrees and determined by flameless atomic-absorption. In 10 g of Zn oe 50 g of Zn(NO(3))(2).6H(2)O the limit of detection is 0.1-60 ppM and the coefficient of variation was 2.7-20%.     

脱硫化氢活性炭的再生方法研究

采用了溶剂再生法和气体再生法对脱硫化氢失活后的活性炭进行再生,溶剂再生时所用的溶剂为H2O2溶液、HNO3溶液以及NaOH溶液。结果表明,NaOH溶液不能使活性炭得到再生,而H2O2溶液、HNO3溶液能够通过氧化的方法使活性炭得到再生。气体再生时所用的气体分别为高纯N2,含20%O2的N2,H2,它们再生的原理分别是热再生,通过氧化单质硫再生和通过还原单质硫再生。再生效果最好的是30%的HNO3溶液和H2,它们能将活性炭孔道内的单质硫分别脱出69.8%和81.2%,再生后的活性炭中硫容量能达到原来的70%以上。再生后活性炭的比表面积和pH值是再生性能的两个重要指标。