The growth of soft magnetic FeNiN thin films under different experimental procedures

FeNiN thin films with good soft magnetic properties were synthesized on Si (1 0 0) substrates at 473 K by RF magnetron sputtering. The dependence of phase structure and magnetic properties on nitrogen partial pressure, nickel concentrations, film thickness and substrate temperature were systematically investigated. The phase evolution from α-(Fe,Ni)N to ξ-(Fe,Ni)₂N with increase of nitrogen partial pressure was seen. The addition of Ni caused FeNiN films to turn from BCC structure to FCC structure. Clear reproducible striped domains appeared at the film surfaces when X_Ni=19.6%, which is explained by the high enough perpendicular anisotropy and the small stress in the film. All films show smooth surfaces and good soft magnetic properties compared to corresponding FeN compounds. The magnetic properties depended dramatically on the phase structure. Optimum soft magnetic properties with H_C of <1 Oe are obtained between 5.0%?X_Ni?10.0%.     

Effect of Cr on the magnetic properties of evaporated CoxCr1−x/Si(1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si(1 0 0) and glass substrates. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Alternating gradient field magnetometer (AGFM) measurements provided saturation magnetization values ranging from 220 to 1200 emu/cm³. Values of squareness exceeding 0.8 have been measured. Coercive field may reach values up to 700 Oe, depending on the percentage of chromium, as well as the substrate nature and the direction of the applied magnetic field. The saturation magnetization value decreases as the Cr content increases. In order to study their dynamical magnetic properties, Brillouin Light Scattering (BLS) measurements have been performed on these samples. Stiffness constant value and anisotropy magnetic field were adjusted to fit the experimental BLS spectra. These results are analyzed and correlated.     

Structure, magnetic and magnetostrictive properties of as-deposited Fe-Ga thin films

Polycrystalline Fe_100−xGa_x (19?x?23) films were grown on Si(1 0 0) substrates at different partial pressures of sputtering gas ranging from 3 to 7 μbar. Microstructural, magnetic and magnetostrictive properties were studied using X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and magneto-optic Kerr effect (MOKE) magnetometry respectively. X-ray diffraction showed that all films have the body-centered cubic (bcc) Fe-Ga phase with the 〈1 1 0〉 direction out of the film plane. Magnetic characterization of the films showed that the films prepared at 3 μbar had weak uniaxial anisotropy whereas films grown at Ar pressures in the range 4-7 μbar were magnetically isotropic. The effective saturation magnetostriction constants (λ_eff) of the films were measured using the Villari effect. It was found that effective saturation magnetostriction constants were almost constant over the Ga composition range achieved by varying the sputtering pressure. The measured effective magnetostriction constants fit closely to the calculated saturation magnetostriction constants of 〈1 1 0〉 textured polycrystalline films with the 〈1 1 0〉 directions slightly canted with respect to the normal to the sample surface. It was found that a high pressure of the sputtering gas effected the magnetic softness of the films. The saturation field increased and remanence ratio decreased with increase in pressure.     

Soft magnetic properties of FeCo films with Co underlayer

Bilayered Fe₆₅Co₃₅ (=FeCo)/Co films were prepared by facing targets sputtering with 4πM_s∼24 kg. The soft magnetic properties of FeCo films were induced by a Co underlayer. H_c decreased rapidly when the Co underlayer was 2 nm or more. The films showed well-defined in-plane uniaxial anisotropy with the typical values of H_ce=10 Oe and H_ch=3 Oe, respectively. High frequency characteristics of the films show the films can work at 0.8 GHz with real permeability as high as 250.     

Structural and magnetic properties of evaporated Fe thin films on Si(1 1 1), Si(1 0 0) and glass substrates

We present experimental results on the structural and magnetic properties of series of Fe thin films evaporated onto Si(1 1 1), Si(1 0 0) and glass substrates. The Fe thickness, t, ranges from 6 to110 nm. X-ray diffraction (XRD) and atomic force microscopy (AFM) have been used to study the structure and surface morphology of these films. The magnetic properties were investigated by means of the Brillouin light scattering (BLS) and magnetic force microscopy (MFM) techniques. The Fe films grow with (1 1 0) texture; as t increases, this (1 1 0) texture becomes weaker for Fe/Si, while for Fe/glass, the texture changes from (1 1 0) to (2 1 1). Grains are larger in Fe/Si than in Fe/glass. The effective magnetization, 4πM_eff, inferred from BLS was found to be lower than the 4πM_S bulk value. Stress induced anisotropy might be in part responsible for this difference. MFM images reveal stripe domain structure for the 110 nm thick Fe/Si(1 0 0) only.     

Effect of magnetic field on the TC and magnetic properties for the aligned MnBi compound

In the compound MnBi, a first-order transition from the paramagnetic to the ferromagnetic state can be triggered by an applied magnetic field and the Curie temperature increases nearly linearly with an increase in magnetic field by ∼2 K/T. Under a field of 10 T, T_C increases by 20 and 22 K during heating and cooling, respectively. Under certain conditions a reversible magnetic field or temperature induced transition between the paramagnetic and ferromagnetic states can occur. A magnetic and crystallographic H-T phase diagram for MnBi is given. Magnetic properties of MnBi compound aligned in a Bi matrix have been investigated. In the low temperature phase MnBi, a spin-reorientation takes place during which the magnetic moments rotate from being parallel to the c-axis towards the basal plane at ∼90 K. A measuring Dc magnetic field applied parallel to the c-axis of MnBi suppresses partly the spin-reorientation transition. Interestingly, the fabricated magnetic field increases the temperature of spin-reorientation transition T_s and the change in magnetization for MnBi. For the sample solidified under 0.5 T, the change in magnetization is ∼70% and T_s is ∼91 K.     

Effect of surface chemisorption on the spin reorientation transition in magnetic ultrathin Fe film on Ag(0 0 1)

We have investigated the effect of surface chemisorption on the spin reorientation transitions in magnetic ultrathin Fe films on Ag(0 0 1) by means of the polar and longitudinal magneto-optical Kerr effect (MOKE) and X-ray magnetic circular dichroism (XMCD) measurements. It is found by the MOKE that adsorption of O₂ and NO induces the shift of the critical thickness for the transitions to a thinner side, together with the suppression of the remanent magnetization and the coercive field of the Fe film. This implies destabilization of the perpendicular magnetic anisotropy. On the other hand, H₂ adsorption is found not to change the magnetic anisotropy, though the enhancement of the coercive field is observed. The XMCD reveals that although both the spin and orbital magnetic moments along the surface normal are noticeably reduced upon O₂ and NO adsorption, the reduction of the orbital magnetic moments are more significant. This indicates that the destabilization of the perpendicular magnetic anisotropy upon chemisorption of O₂ and NO originates from the change of the spin-orbit interaction at the surface.     

Dependence of magnetic anisotropy of the La0.67Ca0.33MnO3 films on substrate and film thickness

Strain in the La_0.67Ca_0.33MnO₃ films has been tuned by varying substrate and film thickness, and its effects on magnetic anisotropy are studied based on the measurements of isothermal magnetization. Measuring the strain in the films by the out-of-plane lattice parameter (c), we found a strong dependence of the magnetic anisotropy constant (Ku) on strain. Ku decreases linearly from ∼−1.1×10⁶ erg/cm³ for c=0.763 nm to 1.2×10⁶ erg/cm³ for c=0.776 nm, corresponding to a change from tensile strain to compressive strain. Positive Ku signifies a uniaxial anisotropy with the easy axis perpendicular to the film plane, while negative Ku demonstrates an anisotropy of the easy plane character. Smaller or larger c leads a decrease or increase in Ku, which indicates the presence of other effects in addition to those associated with strain. Three distinctive processes for the magnetization are observed along the hard magnetic axis of the films on (001)SrTiO₃, suggesting a possibility of strain relaxation even in ultra-thin films.     

Synthesis of Fe3O4 nanoparticles without inert gas protection used as precursors of magnetic fluids

Fe₃O₄ nanoparticles were hydrothermally synthesized under continuous microwave irradiation from FeCl₃·6H₂O and FeSO₄·7H₂O aqueous solutions, using NH₄OH as precipitating reagent and N₂H₄·H₂O as oxidation-resistant reagent. The results of X-ray powder diffraction (XRD), FT–IR spectroscopy and scanning electron microscopy (SEM) measurements showed that the synthesized magnetite (Fe₃O₄) nanoparticles had an average diameter of 10 nm. The magnetic properties of the Fe₃O₄ nanoparticles were measured using a vibrating sample magnetometer (VSM), indicating that the nanoparticles possessed high saturation magnetization at room temperature. The Fe₃O₄ nanoparticles were used to prepare magnetic fluids (MFs) based on water, and the properties of the MFs were characterized by a Gouy magnetic balance, a capillary rheometer and a rotating rheometer, respectively.     

Magnetic transition in Co/(Gd–Co) multilayers

[Co/Gd_0.36Co_0.64]₄/Co multilayers with Co termination layer have been prepared by rf sputtering. They form macroscopic ferrimagnets with a compensation temperature (T_comp) determined by the thickness ratio of the layers. In low fields the magnetization of Co and Gd–Co layers are along the axis of the applied field. Increasing field makes the moments of both the Co and Gd–Co layers deviate from the axis of the field giving rise to a transition into a twisted state. These magnetic transitions were studied by vibrating sample magnetometer (VSM), magneto-optic Kerr effect and magnetoresistance measurements at various temperatures. The nucleation and evolution of surface- and bulk-twisted magnetic states were also observed in these multilayers.     

Numerical simulation of magnetic interactions in polycrystalline YFeO3

The magnetic behavior of polycrystalline yttrium orthoferrite was studied from the experimental and theoretical points of view. Magnetization measurements up to 170 kOe were carried out on a single-phase YFeO₃ sample synthesized from heterobimetallic alkoxides. The complex interplay between weak-ferromagnetic and antiferromagnetic interactions, observed in the experimental M(H) curves, was successfully simulated by locally minimizing the magnetic energy of two interacting Fe sublattices. The resulting values of exchange field (H_E=5590 kOe), anisotropy field (H_A=0.5 kOe) and Dzyaloshinsky–Moriya antisymmetric field (H_D=149 kOe) are in good agreement with previous reports on this system.     

Surface microstructure and magnetic behavior in FeSiB amorphous ribbons from magneto-optical Kerr effect

The magneto-optical Kerr effect (MOKE) completed by other surface sensitive methods as integral low-energy and conversion electron Mössbauer spectroscopy, scanning and transmission electron microscopy and by X-ray diffraction have been used with the aim to trace the surface microstructure and magnetic properties of FeSiB amorphous ribbons prepared by planar flow casting. The general composition of studied samples is Fe₈₀Si_xB_20−x, where x=4, 6, 8, 10 at.%.It is shown that MOKE used for magnetization, hysteresis loop, and domain structure determination is highly beneficial in a detection of both surface crystallization and local ordering of atoms into magnetically different clusters of amorphous structure. Moreover, a combination of blue and red laser with different penetration depths yields unique results concerning the surface anisotropy and depth sensitivity. In the case of samples with 4, 6, and 8 at.% Si MOKE detects two magnetically different phases diverging in coercivity values H_c, however, not varying with the sample composition. These phases have been identified by Mössbauer measurements as FeSi and FeB clusters. Their relationship changes with Si concentration. On the other hand, a strong increase in the surface H_c found for the sample with 10 at.% Si has indicated a nanocrystallization. It was confirmed by electron microscopy, Mössbauer and X-ray diffraction results. The size of nanocrystals has varied between 200 nm and 500 nm.     

Magnetic excitations in (SiO2)Co nano-composite films: Brillouin light scattering study

Behaviour of magnetic excitations in the Damon-Eshbach (DE) and backward volume (BV) geometries in nano-composite (SiO₂)_100−xCo_x (50% at<x<80% at) films has been studied by Brillouin light scattering (BLS). It has been shown that it is the structure of Stokes/anti-Stokes BLS lines in the DE geometry that allows reliable identification of dipole-exchange spin waves (SW) and numerical estimation of the value of the effective exchange constant A_eff of a super-ferromagnetic nano-granular sample (x=80% at).     

Study on the surface bioactivity of novel magnetic A-W glass ceramic in vitro

Novel magnetic A-W glass ceramic (M GC) in the system MgO-CaO-SiO₂-P₂O₅-CaF₂-MnO-ZnO-Fe₂O₃ was synthesized by doping Mn-Zn ferrite to apatite-wollastonite glass ceramic. The phase composition was investigated by XRD. The magnetic property was measured by VSM. The in vitro bioactivity was tested by immersion in simulated body fluid. The result shows apatite, wollastonite, fluorapatite and Zn_0.75Mn_0.75Fe_1.5O₄ are the main phases of M GC. Under a magnetic field of 10,000 Oe, the saturation magnetization and coercive force of the material are 6 emu g⁻ and 180 Oe, respectively. After soaking in SBF for 14 days, the surface of M GC is coated by a hydroxycarbonate apatite layer.     

Structure, magnetic and electrical transport properties of cosputtered Fe0.5Ge0.5 nanocomposite films

Fe_0.5Ge_0.5 nanocomposite films with different film thicknesses were fabricated using cosputtering. The films are composed of Ge, Fe and Fe₃Ge₂, and are ferromagnetic at room temperature. The saturation magnetization and magnetic interaction including dipolar interaction and exchange coupling increase with the increasing film thickness. The electrical conductance mechanism turns from metallic to semiconducting and the saturation Hall resistivity ρ_xys increases with the decreasing film thickness. At 28 nm, ρ_xys is ∼137 μΩ cm at 2 K, about 150 times larger than that of pure Fe film (0.9 μΩ cm) and four orders larger than that of bulk Fe. The ρ_xy-H curves of all the films show the same linearity character in low-field range even though the temperature-independent slope is different at different film thicknesses. At high temperatures, the skew scattering mechanism is dominant. At low temperatures, side-jump effect should be dominant at large resistivity ρ_xx regime for the thin films, and the skew scattering is dominant at small ρ_xx regime for the thick films.     

Magnetic and magneto-optical properties of MnSb films on various substrates

Magnetic and magneto-optical properties of MnSb films with different crystalline orientations on various semiconductors of GaAs(1 0 0), GaAs(1 1 1)A, B, and sapphire(0 0 0 1) have been measured by a vibrating sample magnetometer (VSM) and a home-made magneto-optical Kerr effect (MOKE) system. All these samples have their easy axes in the plane and show ferromagnetic properties. Among these samples, the film on GaAs(1 1 1)B has the lowest coercive force H_c and the largest squareness (SQ) value, whereas the film on GaAs(1 0 0) shows the largest H_c and the lowest SQ value. A large Kerr rotation angle of about 0.3° was observed at a wavelength of λ=632.8 nm for the film on sapphire in the field applied both parallel and perpendicular to the film plane. However, the MnSn films on other substrates do not have an observable Kerr rotation. The dynamic effect of the hysteresis was also measured using our MOKE system. As the frequency of applied magnetic field increases, the loop rounds off at the corners and the loop area increases.     

In-plane magnetic anisotropies in Ni/FeMn and Ni90Fe10/FeMn exchange biased bilayers

The in-plane magnetic anisotropy in Ni/FeMn and Ni₉₀Fe₁₀/FeMn exchange-biased bilayers prepared by co-evaporation under molecular beam epitaxy conditions is investigated employing longitudinal magneto-optical Kerr effect (MOKE) and ferromagnetic resonance (FMR). The exchange anisotropy was induced by a magnetic field cooling immediately after the deposition of the bilayers. Besides the induced term, the presence of an additional uniaxial anisotropy in the FM layers was detected both by MOKE and FMR, and the characteristic directions of these two anisotropy terms are not coincident. The interplay between the anisotropy contributions is discussed considering micromagnetic simulations and the in-plane resonance condition for different magnetic field orientation. X-ray diffraction, X-ray photoelectron spectroscopy, and Mössbauer spectroscopy were used to complement the characterization of the samples.     

Ferromagnet/superconducting YBa2Cu3O7−δ bilayer devices

A magnetic fringe-field effect has been investigated for a simple bilayer device structure consisting of a Co_0.9Fe_0.1 film and an epitaxial YBa₂Cu₃O_7−δ (YBCO) film patterned as a microbridge. The resistance of the bridge is measured with a four-probe technique and is found to depend on the orientation of a magnetic field, which is externally applied in the device plane. A maximum (minimum) of the resistance occurs when the magnetic field is applied in parallel (perpendicular) to the bridge axis. The difference between the maximum and the minimum is very large for a small range of temperature below the critical temperature of the YBCO film. The observed features in the resistance are qualitatively explained by vortex motion in the YBCO bridge under the influence of the magnetic fringe-field of the Co_0.9Fe_0.1 film.     

High-frequency characteristics of CoFeVAlONb thin films

High-frequency characteristics of CoFeVAlONb thin films were studied. A thin film of Co_43.47Fe_35.30V_1.54Al_5.55O_9.93Nb_4.21 is observed to exhibit excellent magnetic properties; magnetic coercivity of 1.24 Oe, uniaxial in-plane anisotropy field of 66.99 Oe, and saturation magnetization of 19.8 kG. The effective permeability of the film is as high as 1089 and is stable up to 1.8 GHz, and with ferromagnetic resonance over 3 GHz. This film also has very high electrical resistivity of about 628 μΩ cm. These superior properties make it ideal for high-frequency magnetic applications.     

Synthesis and magnetic properties of Zn1−xMnxO films prepared by the sol-gel method

We report on the ferromagnetic characteristics of Zn_1−xMn_xO films (x=0.1-0.3) prepared by the sol-gel method on silicon substrates using transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffractometry (XRD) and superconducting quantum interference device (SQUID) magnetometry at various temperatures. Magnetic measurement show that the Curie temperature (T_C) and the coercive field (H_C) were ∼39 K and ∼2100 Oe for the film of x=0.2, respectively. EDS and TEM measurements indicate that Mn content at the interface is significantly higher than that at the center of the Zn_0.8Mn_0.2O film showing the ratio, Zn:Mn:O≅1:12:15. This experimental evidence suggests that ferromagnetic precipitates containing manganese oxide may be responsible for the observed ferromagnetic behavior of the film.