Full vectorial finite element modeling of novel polarization rotators

In this paper, the numerically efficient finite element based full vectorial modal and propagation approaches are used in order to analyze and design single and multiple sectioned passive polarization rotators (PRs). The effects of different waveguide parameters, such as the waveguide width, etching depth, sidewall slant angle and refractive index contrast on the PR performance in terms of polarization conversion efficiency, section length and losses are investigated in detail in order to obtain optimum PR designs. Moreover, a thorough sensitivity study of the fabrication tolerances and the operating wavelength on the performance of the PRs has also been carried out.     

Multiplexer–Demultiplexer based on nematic liquid crystal photonic crystal fiber coupler

A novel design of Multiplexer–Demultiplexer (MUX–DEMUX) based on index guiding soft glass nematic liquid crystal (NLC) based photonic crystal fiber coupler is proposed and analyzed. The simulation results are obtained using the full vectorial finite difference method as well as the full vectorial finite difference beam propagation method. The numerical results reveal that the proposed MUX–DEMUX of length 3.265 mm can provide low crosstalk better than −20dB with great bandwidths of 40 and 24 nm around the wavelengths of 1.3 and 1.55 μm, respectively. In addition, the reported MUX–DEMUX has a tolerance of ±3% in its length which makes the design more robust to the perturbation introduced during the fabrication process.     

Accurate radial basis function based neural network approach for analysis of photonic crystal fibers

In this paper, a new and an accurate artificial neural network approach (ANN) is presented for the analysis and design of photonic crystal fibers (PCFs). The new ANN approach is based on the radial basis functions which offer a very quick convergence and high efficiency during the ANN learning. The accuracy of the suggested approach is demonstrated via the excellent agreement between the results obtained using the presented approach and the results of the full vectorial finite difference method (FVFDM). In addition, a new design of highly birefringence PCF with low losses for the two polarized modes is presented using the proposed approach.     

基于全矢量模式匹配法的三维弯曲波导本征模式计算

采用精确、严格的全矢量模式匹配法，计算了三维脊型弯曲波导和条形弯曲波导的本征模式，分析了模式折射率和辐射损耗随弯曲半径的变化关系.计算结果与已报道的有限差分法的结果符合很好.对文献中已报道但没有深入分析的现象给出了合理的解释.半径为50和12 μm的条形波导的计算结果表明：当波导的弯曲半径减小时，发生在分界面处的TE-TM模耦合会显著增强，这将导致弯曲波导中的模式不再是传统意义上的准TE模和准TM模，而是混合模.随着半径的减小，混合模的横向分量之间的差异会减小，当两个横向分量达到近似相等的强度时，波导的偏振相关性将会大大减小. 关键词： 导波光学 全矢量模式匹配法 微环谐振腔 光波导理论     

Polarization properties of elliptical core non-hexagonal symmetry polymer photonic crystal fibre

In this paper, polarization properties and propagation characteristics of polymer photonic crystal fibres with elliptical core and non-hexagonal symmetry structure are investigated by using the full vectorial plane wave method. The results show that the birefringence of the fibre is induced by asymmetries of both the cladding and the core. Moreover, by adjusting the non-symmetrical ratio factor of cladding $\eta$ from 0.4 to 1 in step 0.1, we find the optimized design parameters of the fibre with high birefringence and limited polarization mode dispersion, operating in a single mode regime at an appropriate wavelength range. The range of wavelength approaches the visible and near-infrared which is consistent with the communication windows of polymer optical fibres.     

Rotating vectorial vortices produced by space-variant subwavelength gratings

A new class of vectorial vortex based on coherent addition of two orthogonal circularly polarized Bessel beams of identical order but with different propagation constants is presented. The transversely space-variant axially symmetric polarization distributions of these vectorial fields rotate as they propagate, while they maintain a propagation-invariant Bessel intensity distribution. These properties were demonstrated by use of discrete space-variant subwavelength gratings for 10.6 microm CO2 laser radiation. The polarization properties were verified by both full space-variant polarization analysis and measurements. Rotating intensity patterns are also demonstrated by transmitting the vectorial vortices through a linear polarizer.     

Vectorial electromagnetic modes in V-shaped dielectric waveguides with application to quantum wire devices

The properties of V-shaped optical dielectric waveguides are investigated in detail using a vectorial finite element method. The fundamental modes exhibit extremely tight, heart shaped near field patterns. The maximum intensity of the fundamental mode is found to be vertically shifted with respect to the geometrical center of the waveguide. Fundamental and higher order mode properties are extensively studied, including mode patterns, dispersion curves and polarization properties. The local mode polarization of the two fundamental modes varies from a horizontal (vertical) orientation at the groove center to TM (or TE respectively) far in the side wings. The optimal design of waveguides for GaAs/AlGaAs quantum wire diode lasers and Quantum Confined Stark Effect modulators grown on V-grooved substrates is discussed.     

Novel design of photonic crystal fibres with low confinement losses, nearly zero ultra-flatted chromatic dispersion, negative chromatic dispersion and improved effective mode area

A novel photonic crystal fibre (PCF) with a low confinement loss and nearly zero ultra-flatted chromatic dispersion and negative chromatic dispersion at a wide telecommunication window is presented. Important PCF design parameters, such as the effects of air holes and geometrical parameters on the effective index, confinement losses, chromatic dispersion and effective mode area, have been thoroughly investigated by employing the full vectorial finite element method. Significant reduction of the confinement loss and low chromatic dispersion of the PCF, with three rings of air holes, has been obtained by carefully incorporating additional air holes.     

Highly sensitive octagonal photonic crystal fiber based sensor

In this study, a number of propagation characteristics of hexagonal and octagonal photonic crystal fiber (H-PCF and O-PCF) structures, where both core and cladding are microstructured have been investigated by employing the full vectorial finite element method (FEM). The confinement loss, the effective refractive index and the relative sensitivity coefficient behaviors of the O-PCF and the standard H-PCF are numerically investigated and compared. It is found that under the same design parameters O-PCF structure has significantly lower losses and higher relative sensitivity coefficient compared with H-PCF structure.     

光学薄膜诱导偏振像差对大数值孔径光学系统聚焦特性的影响

大数值孔径光学系统表面光线的入射角较大, 会导致薄膜的偏振分离, 诱发偏振像差, 影响光学系统的聚焦特性. 本文利用矢量光衍射理论, 建立了光学薄膜各参量与光学系统聚焦光场的模型. 利用该模型分析了线偏振光入射时, 光学薄膜对光学系统聚焦光斑的扰动. 在此基础上, 探讨了应用了不同约束条件下得到的光学薄膜对最终聚焦光场的影响, 确定了减小薄膜扰动光学系统光斑的设计方法, 即额外添加透射率差和位相差的约束条件, 并且适当增加位相差约束的权重. 利用该方法优化设计的薄膜, 相比于普通减反膜而言, 对系统聚焦光场中心强度的提升可达约12.5%.     

矩形点阵微结构聚合物光纤偏振特性研究

采用全矢量平面波方法,以聚合物为基材,研究了矩形点阵微结构聚合物光纤的传输模场和偏振性质.结果发现,矩形点阵微结构聚合物光纤基模两个正交偏振态不再简并,模场呈现类矩形且具有较强的线偏振特性;该光纤模式双折射产生于包层孔结构分布的不对称性,减小包层纵向孔间隔和横向孔间隔之比η值,双折射明显增强,适当调节η,可在更宽频带范围内实现高双折射单模运行.     

一种新型高双折射光子晶体光纤

提出了一种新的高双折射光子晶体光纤结构.应用全矢量频域有限差分方法所做的数值分析表明：该结构光纤基模的两个正交偏振态不再简并，其模式呈现很强的线偏振特性,并且模式双折射与结构参数设置有密切关系.通过选择合适的结构参数，可以使之达到10^-2量级，比传统的D型和熊猫型保偏光纤高出2个数量级.合理设计光纤包层的几何结构，可以取得理想的色散效果.这种结构的光子晶体光纤可用于制作具有适当色散特性或偏振特性的保偏光纤及相关光纤器件. 关键词： 光子晶体光纤 模式双折射 偏振特性 频域有限差分法     

微结构聚合物光纤中高双折射可调效应研究

通过在纤芯附近引入两个直径较大的空气孔诱导纤芯局部双折射,在包层减小x方向的孔间隔诱导包层双折射,设计实现了一种高双折射随波长可调效应的微结构光纤.采用全矢量平面波方法,以聚合物甲基丙烯酸甲酯为基材,对其偏振特性和基模模场进行了研究.结果发现,该光纤基模双折射在光通信波段呈现两个最大值,且最大双折射大小和位置随光纤结构和波长的变化可以进行调节.通过调节光纤结构参数,模拟得到了该光纤具有高双折射和零偏振模色散的最佳设计参数. 关键词： 导波与光纤光学 双折射可调 聚合物 全矢量平面波法     

直流固态继电器电磁脉冲失效模式实验研究

采用电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制及失效模式进行了实验研究,结果表明:输入端注入电磁脉冲信号时,输出端会产生误动作,并可造成输入电路中三极管BE节产生短路损伤,导致输入端施加控制信号时输出端无法导通;输出端注入电磁脉冲信号时,可造成输出电路中MOSFET管的栅极和漏极产生短路损伤,导致输出端短路。     

Design of Ultra Compact Polarization Splitter Based on the Complete Photonic Band Gap

A novel design of polarization splitter based on the complete photonic band gap has been proposed in this paper. The proposed Photonic Band Gap (PBG) polarization splitter is formed by two photonic crystal waveguides composed of dielectric rods in air in honeycomb structure for which complete photonic band gap is obtained using the plane wave expansion (PWE) method. The splitting properties (i.e. coupling length, extinction ratio and insertion loss) of PBG polarization splitter have numerically been investigated using the finite difference time domain (FDTD) method. It has been shown that polarization splitter of length as small as 32 μm can be designed at λ=1.55 μm. The proposed polarization splitter offers a large bandwidth of 120 nm.     

Model of Vernier devices in silicon-on-insulator technology

In order to increase the number of channels that could be multiplexed or demultiplexed in the dense wavelength division multiplexed (DWDM) system based on the resonators on silicon-on-insulator (SOI) technology, the Vernier effect in the series-coupled racetrack resonators is presented to extend the free spectral range (FSR) of the DWDM systems. A method is developed based on a matrix approach to simulate Vernier devices. A three-dimensional full vectorial finite difference (FVFD) model, specifically suited for high index contrast and smaller size waveguides, for example, a waveguide in SOI technology, is developed to obtain the properties of a waveguide. Finally, the Vernier effect in the two series-coupled racetrack resonators is experimentally verified with an improved FSR and interstitial resonance suppression.     

一种新型的基于四孔单元光子晶体光纤的设计与分析

设计了一种基于四孔单元的光子晶体光纤,它可以满足光通信系统中高双折射率、负色散和低限制损耗的要求,比起通常的三角结构光纤有着更高的双折射率,并且结构制作也较简单。采用全矢量有限元法和各项异性完美匹配层法对所设计的光纤进行了仿真研究。仿真结果表明:该光纤在1.55μm波长处可获得10~(-2)数量级的双折射率,在较宽广的波段范围具有大的负色散,限制损耗低于10~(-9)dB/m;该光纤在保偏光纤、单极化单模光纤、色散补偿光纤等方面具有重要的应用。     

Highly nonlinear birefringent photonic crystal fiber

We propose an index guiding highly nonlinear birefringent photonic crystal fiber (PCF). Using a full vectorial finite element method (FEM), we investigate the key propagation characteristics of the proposed design. We demonstrate that it is possible to design a simple PCF structure configuration with a birefringence in the order of 10⁻² and a nonlinear coefficient of 49 W⁻¹ km⁻¹ at the wavelength of 1.55 μm. It is demonstrated that two zero dispersion wavelengths can be achieved by the proposed design. Bending analysis and fabrication issues are also discussed thoroughly.     

一种近似矢量衍射模型在衍射微光学元件分析中的应用

标量衍射理论形式简洁，有很高实用性，但是在衍射微光学元件分析中显得模型粗糙，准确度下降。严格矢量衍射理论由于计算复杂，非常耗费时间和资源，因此也不是一种很有效的设计工具。 我们在本文中运用了一种简单的近似矢量衍射模型分析了几种典型衍射微光学元件衍射性能，此衍射模型采用了标量衍射理论和近似近场模型的结合。 TE和TM两种偏振模式均运用此近似矢量衍射模型进行了分析，我们发现此衍射模型可以得到比标量衍射理论更准确的结果，而与严格电磁场理论相比，它占用很少的计算时间。     

Modeling of graded index waveguide fabricated by ion exchange on Er3+ doped glass

A general numerical tool,based on thermal diffusion equation and full-vectorial eigen-mode equation,has been presented for the systematic analysis of graded index channel waveguide fabricated by ion exchange on Er3+ doped glass.Finite difference method with full-vectorial formulation(FV-FDM) is applied to solving the full-vectorial modes of graded index channel waveguide for the first time.The coupled difference equations based on magnetic fields in FV-FDM are derived from the Taylor series expansion and accurate formulation of boundary conditions.Hybrid nature of vectorial guided modes for both pump(980 nm) and signal light(1550 nm) are demonstrated by the simulation.Results show that the fabrication parameters of ion exchange,such as channel opening width and time ratio of second step to first step in ion exchange,have large influence on the properties of waveguide.By optimizing the fabrication parameters,maintenance of monomode for signal light and improvement of the gain dynamics can be achieved in Er3+ doped waveguide amplifier(EDWA) fabricated by ion exchange technique.This theoretical model is significant for the design and fabrication of EDWA with ion exchange technique.Furthermore,a single polarization EDWA,which operates at wavelength from 1528 nm to 1541 nm for HE polarization,is numerically designed.