基于微扰近似的圆锥表面光散射

由Hueygen原理出发,介绍了粗糙表面的光散射特性.基于微扰近似,在不考虑遮蔽效应和圆锥顶点的散射情况下,分析了圆锥物体的光散射特性,推导了圆锥物体对平面光的散射场解析表达式.计算了圆锥表面在高度起伏均方根不同情况下对1.06μm光波的散射,并且得到了入射角一定的情况下,不同观察方向的散射光强分布曲线.结果表明,在观察方位角不变时,圆锥的散射光强随观察角顶角的增加先增大后减小;在观测方位角一定时,散射光强随高度起伏均方根的增加而减小,且随观察方位角呈对称分布.     

基于微扰近似的圆锥表面光散射*

由Hueygen原理出发,介绍了粗糙表面的光散射特性.基于微扰近似,在不考虑遮蔽效应和圆锥顶点的散射情况下,分析了圆锥物体的光散射特性,推导了圆锥物体对平面光的散射场解析表达式.计算了圆锥表面在高度起伏均方根不同情况下对1.06μm光波的散射,并且得到了入射角一定的情况下,不同观察方向的散射光强分布曲线.结果表明,在观察方位角不变时,圆锥的散射光强随观察角顶角的增加先增大后减小|在观测方位角一定时,散射光强随高度起伏均方根的增加而减小,且随观察方位角呈对称分布.     

指数型分层介质粗糙面光透射问题的微扰法

运用微扰法研究了平面波入射分层介质粗糙面的光透射问题,推出了不同极化状态的透射系数公式.采用指数型粗糙面模拟实际的分层介质粗糙面,结合其功率谱导出了平面波入射时的透射系数计算公式.通过数值计算得到了HH极化情形透射系数随透射光散射角变化的曲线.数值计算结果表明,底层介质介电常量对透射系数几乎没有影响;中间介质介电常量影响透射系数的大小及透射系数角分布曲线;中间介质厚度增大为原来的二倍时,曲线振荡的周期减小为原来的二分之一;粗糙面高度起伏均方根影响透射系数的大小、曲线振荡的振幅;粗糙面高度起伏相关长度既影响透射系数的大小、同时影响曲线的振荡行为;透射系数随入射波长的增大而振荡减小.     

湍流大气中随机粗糙表面激光回波空间相干性仿真

根据广义Huygens-Fresnel原理,推导了von Karman湍流谱条件下激光回波复相干度的理论解析式;基于湍流相位屏分步传输算法和随机粗糙目标表面模型,实现了激光回波光场的仿真计算.首先通过镜面反射回波光场的仿真分析,验证了算法的正确性;然后基于1.1 km的均匀传输路径,综合分析了随机粗糙目标表面特性和路径湍流强度对回波光场复相干度的影响.结果表明:回波光场的空间相干性随目标表面高度均方根的增大而降低,随目标表面相关长度的减小而降低;当表面相关长度远小于大气相干长度时,回波相干性会被严重破坏.该研究可为目标表面特性或利用已知表面获取路径湍流状态的相干探测提供有益的参考.     

小斜率近似在粗糙面激光散射BRDF计算中的应用

基于小斜率近似法建立了粗糙面激光散射双向反射分布函数的数学模型,采用该模型计算了粗糙度参量已知的合金铝样片的双向反射分布函数值,计算结果与实测结果吻合良好,验证了模型的正确性.研究了粗糙度参量和样片光学常量对双向反射分布函数的影响,结果表明,粗糙面激光散射的双向反射分布函数与表面高度起伏均方根、自相关长度及样片光学常量相关.当入射波长一定时,高度起伏均方根越大,或者自相关长度越小,粗糙面粗糙度越大,入射激光的漫反射特性越强,双向反射分布函数峰值越小且分布越分散;当粗糙度一定时,样片光学常量对双向反射分布函数影响较大,粗糙面对入射激光复折射率的虚部越大,样片双向反射分布函数的峰值越小,当粗糙度参量增大时,样片光学参量对双向反射分布函数的影响逐步减弱.     

雪层覆盖土壤表面与半埋柱体宽带复合散射FDTD方法

为满足半埋目标测量和检测的需要,应用指数型分布粗糙面模型和Monte Carlo方法模拟雪层、土壤表面,运用时域有限差分方法研究雪层覆盖的土壤表面与半埋矩形截面柱复合模型的宽带电磁散射,得出宽带复合散射系数的频率响应曲线,计算宽带复合散射系数随雪层表面、土壤表面高度起伏均方根、相关长度,雪层类型、雪层厚度,土壤层含水量,矩形截面柱几何参数、倾角、埋藏深度,电磁波入射角等参数的变化. 结果表明,雪层表面高度起伏均方根、相关长度对宽带复合散射系数影响较小,其它参数对宽带复合散射系数均有显著影响且较为复杂.     

目标粗糙对合成孔径激光雷达回波的退相干效应

本文研究了目标表面粗糙对回波信号探测的影响,通过蒙特卡罗方法建立一维和二维目标高斯随机粗糙面模型,并对目标回波信号的探测过程进行仿真,研究目标表面粗糙对中频信号的影响.还进行了粗糙面和光滑面两组光外差探测实验,验证目标粗糙对合成孔径激光雷达回波信号严重的“退相干”效应.同时,采用数字波前分析仪对探测器处本振光和信号光波前分别进行检测,检测结果与仿真一致,证明粗糙面回波相位畸变严重.文中研究结果对设计光源参数、接收系统参数以及评估系统作用距离奠定基础,为合成孔径激光雷达系统设计提供定量参考.     

指数型粗糙地面与上方矩形截面柱宽带电磁散射的时域有限差分法研究

采用土壤介电常数的四成分模型表示实际地面的介电特性,应用指数型分布粗糙面模型和Monte Carlo方法模拟实际的粗糙地面,运用时域有限差分方法研究了微分高斯脉冲波照射时粗糙地面与上方目标的宽带电磁散射问题,得出了后向复合散射系数的频率响应曲线,计算了后向复合散射系数随粗糙地面高度起伏均方根、相关长度、土壤湿度、目标尺寸、高度、倾角等几何参数及介电参数等的变化情况,并做了详细分析与讨论,得到了指数型粗糙地面与上方目标宽带电磁散射特性.     

土壤表面与部分埋藏多目标复合散射的时域有限差分方法

采用Dobson半经验模型和电介质复介电常数表示土壤介电常数的实部和虚部,用指数型分布粗糙面和Monte Carlo方法模拟土壤表面,运用时域有限差分方法研究土壤表面与部分埋藏多个矩形截面混凝土柱复合模型的电磁散射.结果表明：复合散射系数随散射角振荡变化;土壤表面高度起伏均方根、土壤含水率、目标介电常数、入射角对复合散射系数影响较大;土壤表面相关长度、目标截面宽度、高度、间距、倾角对复合散射系数影响较小;目标埋藏深度对复合散射系数几乎没有影响.与其他数值计算方法比较,采用时域有限差分方法既可获得较高的准确性,又可减少计算时间和内存占用量.可以用来计算地、海粗糙面与附近任意多目标的复合散射.     

地面对激光雷达信号散射的统计研究

从理论角度研究了利用高斯光束照射远场目标时,激光散斑的统计特性.导出了散射光场的自相关函数和光强度的二阶矩的解析表达式,计算了激光散斑的面积.研究表明:在接收面上,光强的分布与目标表面高度的相关长度和均方根高度密切相关,激光散斑面积和散斑光强的相关系数只与激光束腰的尺度有关,与目标的均方根高度和相关长度无关. 关键词： 激光散斑 自相关函数 高斯分布 协方差     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.