Femtosecond laser application for high capacity optical data storage

A femtosecond (fs) laser application for multi-layer optical recording is investigated. Information patterns at different layer depths were written inside a transparent glass substrate due to micro-void formation by fs laser ablation, which causes re-distribution in glass materials and a refractive index modification. The information bits recorded in a single layer can be retrieved clearly without interference from the neighboring layers. A fs laser irradiation of a transparent polymer matrix (doped with fluorescent materials for use as low-cost recording media) is also studied. A fs laser induced photo-chemical reaction changes the chemical properties of the fluorescent materials and records information bits inside the matrix. With an ultra-fast laser as a new light source, 3D optical recording can be available for high capacity data storage up to 1 TB per disc. PACS 82.50.-m; 42.65. Re; 72.70.Jk.     

Three-dimension direct writing TiO<Subscript>2</Subscript> crystalline patterns in Bi-free glass using femtosecond laser

Crystalline TiO₂ was induced three dimensionally inside Bi-free glass sample by an 800 nm, 250-kHz femtosecond laser irradiation. Micro-Raman spectra analysis indicated that the laser-induced crystals in the focal point of the laser beam were monophase TiO₂ rutile. Continuous crystalline lines were written through moving the focal point of the laser beam inside the glass. The results demonstrate that this technique is a convenient method to engrave three-dimensional patterns of crystals for fabricating integrated optical devices in transparent materials.     

Threshold effect in femtosecond laser induced nanograting formation in glass: influence of the pulse duration

Recently, femtosecond laser direct writing in porous glass is emerging as a powerful technique for building arbitrary 3D hollow micro/nanostructures in bulk glass materials. In this study, we investigate the pulse duration dependence of laser intensity window for inducing a single nanocrack inside porous glass by femtosecond laser direct writing. We find that the window for a single nanocrack increases with the pulse duration, while the roughness of side walls in the nanocracks becomes higher for pulses longer than ~300 fs. When the femtosecond laser pulses of an optimized duration of ~200 fs are chosen, a sufficiently broad range of laser intensity (~44 % of the structuring threshold) for creating a single nanocrack can be obtained, while smooth sidewalls required by nanofluidic applications can still be maintained. The reported results will be beneficial not only for the development of the 3D femtosecond laser micro/nanostructuring techniques, but also for gaining a deeper understanding of the physical mechanism behind the nanograting formation induced by femtosecond laser irradiation in glass and other transparent materials.     

Liquid-assisted femtosecond laser drilling of straight and three-dimensional microchannels in glass

Ultra-short-pulse lasers have proved to be effective tools for micromachining a wide range of materials. When the ultra-short laser pulse is focused inside the bulk of a transparent medium, nonlinear absorption occurs only near the focal volume that is subjected to high intensity. Three-dimensional structures can be fabricated inside transparent materials by taking advantage of this volumetric absorption. In this paper, femtosecond laser pulses were used to fabricate straight and bent through-channels. Drilling was initiated from the rear surface to preserve consistent absorption of the laser pulse. When the debris was not removed efficiently, variation of the channel diameter and occasional termination of the drilling process were observed. Machining in the presence of a liquid and additional use of ultrasonic wave agitation facilitated the debris ejection. The machined channels had diameters on the order of tens of microns, high aspect ratios, and good wall-surface quality. PACS 42.62.Cf; 42.65.Re; 81.05.Kf; 43.35.+d     

Micromachining bulk glass by use of femtosecond laser pulses with nanojoule energy

Using tightly focused femtosecond laser pulses of just 5 nJ, we produce optical breakdown and structural change in bulk transparent materials and demonstrate micromachining of transparent materials by use of unamplified lasers. We present measurements of the threshold for structural change in Corning 0211 glass as well as a study of the morphology of the structures produced by single and multiple laser pulses. At a high repetition rate, multiple pulses produce a structural change dominated by cumulative heating of the material by successive laser pulses. Using this cumulative heating effect, we write single-mode optical waveguides inside bulk glass, using only a laser oscillator.     

3D features of modified photostructurable glass-ceramic with infrared femtosecond laser pulses

The exclusive ability of laser radiation to be focused inside transparent materials makes lasers a unique tool to process inner parts of them unreachable with other techniques. Hence, laser direct-write can be used to create 3D structures inside bulk materials. Infrared femtosecond lasers are especially indicated for this purpose because a multiphoton process is usually required for absorption and high resolution can be attained. This work studies the modifications produced by 450 fs laser pulses at 1027 nm wavelength focused inside a photostructurable glass-ceramic (Foturan^®) at different depths. Irradiated samples were submitted to standard thermal treatment and subsequent soaking in HF solution to form the buried microchannels and thus unveil the modified material. The voxel dimensions of modified material depend on the laser pulse energy and the depth at which the laser is focused. Spherical aberration and self-focusing phenomena are required to explain the observed results.     

飞秒激光在透明介质中诱导光学微腔的实验研究

鉴于飞秒激光脉冲持续时间极短且峰值功率极高，将其紧聚焦到透明介质体内部时，易引发双光子效应、碰撞电离、雪崩击穿等一系列非线性过程，在焦点处产生微爆，从而形成微腔结构。提出采用25fs的激光脉冲在透明介质内部诱导形成微腔结构。分析了微腔的能量阈值。结合三维精密位移台，制备了三维微腔点阵。探讨了超短激光脉冲在透明介质内部形成微腔结构的方法与基本实验参数。试验发现：采用更短脉宽的飞秒脉冲时可以降低微腔形成的能量阈值；通过调整飞秒激光功率、脉冲作用次数和光束聚焦情况等因素，可以有效改变微腔的纵深比；在数值孔径较低时因无法实现紧聚焦，故不能形成微腔。     

Three‐dimensional femtosecond laser micromachining of photosensitive glass for biomicrochips

Internal modification of transparent materials such as glass can be carried out using multiphoton absorption induced by a femtosecond (fs) laser. The fs‐laser modification followed by thermal treatment and successive chemical wet etching in a hydrofluoric (HF) acid solution forms three‐dimensional (3D) hollow microstructures embedded in photosensitive glass. This technique is a powerful method for directly fabricating 3D microfluidic structures inside a photosensitive glass microchip. We used fabricated microchips, referred to as a nanoaquarium, for dynamic observations of living microorganisms. In addition, the present technique can also be used to form microoptical components such as micromirrors and microlenses inside the photosensitive glass, since the fabricated structures have optically flat surfaces. The integration of microfluidics and microoptical components in a single glass chip yields biophotonic microchips, in other words, optofluidics, which provide high sensitivity in absorption and fluorescence measurements of small volumes of liquid samples.     

Spatially resolved measurement of femtosecond laser induced refractive index changes in transparent materials

We present a practical method to determine femtosecond laser induced refractive index changes in transparent materials. Based on an iterative Fourier transform algorithm, this technique spatially resolves the refractive index of complex structures by combining the dimensions of the modified region with the corresponding phase change extracted from far-field intensity measurements. This approach is used to characterize optical waveguides written by a femtosecond laser in borosilicate glass.     

Pulse width effect in ultrafast laser ionization imaging

The effects of different laser pulse widths on laser-induced ionization imaging of microstructures embedded in transparent materials are investigated. It is shown that a femtosecond laser-induced ionization probe can detect the variation of elemental composition of the sample materials with a higher contrast ratio, whereas the ionization probe generated by picosecond laser pulses is more sensitive to the structural change inside optical materials, which can be well explained by the different roles of multiphoton ionization and avalanche ionization involved in material breakdown. These results also suggest that an optimum diagnosis could be obtained if well-selected laser parameters are employed in ultrafast laser ionization imaging.     

Fabrication of quasi-periodic micro-voids in fused silica by single femtosecond laser pulse

We demonstrate that quasi-periodic void structure can be self-formed in transparent materials by single femtosecond laser pulse. Compared to the multiple-pulse induced structures, the single-pulse induced void structures are very short and may contain absent voids. The formation mechanisms have been discussed comparatively in detail. Based on this, a technique for high-speed and large-area fabrication of micro-void arrays in transparent materials has been presented. The experimental results show that 3D micro-void structures which contain over several hundred thousand voids in micrometer scales are produced in areas of square millimeters within a few minutes, and the periods of micro-void structures can be easily varied by processing parameters. This work has potential applications in 3D optical storage, photonic crystal and integrated optics, and provides novel insight into the interaction between the single femtosecond pulse and the transparent materials.     

Nonlinear imaging of embedded microstructures inside transparent materials with laser-induced ionization microscopy

We present a novel nonlinear imaging method that utilizes femtosecond laser-induced plasma emission to probe microscopic structures embedded inside transparent materials. This nonlinear diagnostic tool can resolve either elemental or structural variations of the sample of interest and provide significant improvements over the ordinary linear microscopes by having much higher contrast ratios for the observed areas of different refractive indices. Examples of using this technique to examine the microstructures fabricated by ultrashort laser pulses inside optical glass are presented.     

Generating optical vortex with computer-generated hologram fabricated inside glass by femtosecond laser pulses

We introduce a novel method to generate the optical vortex with computer-generated hologram (CGH) fabricated inside glass by femtosecond laser pulses. The CGH was directly written inside glass by femtosecond laser pulses induced microexplosion without any pre- or post-treatment of the material. We also realized the restructured optical vortex beams of both the transmission and reflection pattern with high fidelity using a collimated He-Ne laser beam. The total diffractive efficiency of both the transmission and reflection pattern is about 4.79%.     

飞秒脉冲在透明材料中的三维光存储及其机理

使用经钛宝石啁啾脉冲放大的脉冲宽度为200fs、波长为800nm、重复频率为1kHz的超短脉冲激光束,紧聚焦到熔融石英中实现了三维逐位式光数据存储,记录下20层三维数据位点,利用CCD和数码相机对数据位进行了观察讨论了飞秒超短脉冲与透明介质的相互作用,以及产生等离子体的雪崩电离和多光子吸收电离的机理实验结果表明:在飞秒超短脉冲与透明光学介质的相互作用中起主要作用的是多光子吸收.     

Fabrication of 3D microfluidic structures inside glass by femtosecond laser micromachining

Femtosecond lasers have opened up new avenues in materials processing due to their unique characteristics of ultrashort pulse widths and extremely high peak intensities. One of the most important features of femtosecond laser processing is that a femtosecond laser beam can induce strong absorption in even transparent materials due to nonlinear multiphoton absorption. This makes it possible to directly create three-dimensional (3D) microfluidic structures in glass that are of great use for fabrication of biochips. For fabrication of the 3D microfluidic structures, two technical approaches are being attempted. One of them employs femtosecond laser-induced internal modification of glass followed by wet chemical etching using an acid solution (Femtosecond laser-assisted wet chemical etching), while the other one performs femtosecond laser 3D ablation of the glass in distilled water (liquid-assisted femtosecond laser drilling). This paper provides a review on these two techniques for fabrication of 3D micro and nanofluidic structures in glass based on our development and experimental results.     

单次飞秒激光脉冲在玻璃内部产生多次微爆的研究

在入射能量不同的情况下，用近红外飞秒激光脉冲在重钡火石玻璃（ZBaF15）内部产生了色心和微爆，在熔融石英的内部产生了多次微爆现象.实验表明：入射能量较高时，色心的中间会产生微爆；在松聚焦条件下，一个飞秒激光脉冲在透明介质内会激发多次微爆.基于飞秒激光脉冲在透明介质内的自聚焦效应和自由电子等离子体的自散焦效应，理论分析了多次微爆产生的原因；也讨论了飞秒激光脉冲诱导玻璃折射率改变的机理.     

Femtosecond laser micromachining and biological therapy

Nonlinear micromachining with femtosecond laser pulses has attracted much attention in microphotonics and biophotonics. In this paper, we demonstrate the fabrication of optical elements in bulk transparent materials, direct welding between transparent substrates, and subcellular ablation in living cells by focusing femtosecond laser pulses.     

Three-dimensional hole drilling of silica glass from the rear surface with femtosecond laser pulses

By moving silica glass in a preprogrammed structure, we directly produced three-dimensional holes with femtosecond laser pulses in single step. When distilled water was introduced into a hole drilled from the rear surface of the glass, the effects of blocking and redeposition of ablated material were greatly reduced and the aspect ratio of the depth of the hole was increased. Straight holes of 4-mu;m diameter were more than 200 microm deep. Three-dimensional channels can be micromachined inside transparent materials by use of this method, as we have demonstrated by drilling a square-wave-shaped hole inside silica glass.     

Color center formation in KCl and KBr single crystals with femtosecond laser pulses

Because of their extremely high instantaneous powers, femtosecond lasers can color many nominally transparent materials. Although the excitations responsible for this defect formation occur on subpicosecond time scales, subsequent interactions between the resulting electronic and lattice defects complicate the evolution of color center formation and decay. These interactions must be understood in order to account for the long-term behavior of coloration. In this work, we probe the evolution of color centers generated by femtosecond laser radiation in potassium chloride and potassium bromide single crystals on time scales from microseconds to hundreds of seconds. By using an appropriately chosen probe laser focused through the femtosecond laser spot, we follow the changes in coloration due to individual or multiple femtosecond pulses and the evolution of that coloration for long times after femtosecond laser radiation is terminated.     

Frontispiece: Optical waveguides in crystalline dielectric materials produced by femtosecond‐laser micromachining

Femtosecond‐laser micromachining has been developed as one of the most efficient techniques for direct three‐dimensional microfabrication of transparent optical materials. In integrated photonics, by using direct writing of femtosecond/ultrafast laser pulses, optical waveguides can be produced in a wide variety of optical materials. With diverse parameters, the formed waveguides may possess different configurations. The paper by F. Chen and J.R. Vázquez de Aldana (pp. 251–275) focuses on crystalline dielectric materials, and is a review of the state‐of‐the‐art in fabrication, characterization and applications of femtosecond‐laser micromachined waveguiding structures in optical crystals and ceramics.