扬声器中涡流的热效应

通过分析和比较两种扬声器涡流电学模型和两种扬声器热模型，提出一种分频段的非线性热模型类比线路，给出了对应的音圈稳态温度公式，并在高频段运用逐点测温的方法研究，论证了扬声器涡流随频率变化的规律及其对扬声器热效应的影响。     

封闭式扬声器系统空气劲度的非线性研究

从理想气体多变过程的状态方程出发,推导了封闭式扬声器系统的非线性空气劲度的理论公式。研究发现,封闭式扬声器系统的非线性空气劲度与音圈运动位移、有效辐射面积、箱体有效容积和多变系数等主要因素有关。通过实验,分别测量了封闭式扬声器系统与扬声器单元的非线性劲度,二者相减获得封闭式扬声器系统的非线性空气劲度。实测数据与理论计算得到很好的吻合。     

无内共振时的扬声器分谐波

研究了驱动频率低于扬声器辐射体薄壳轴对称模态最低固有频率的扬声器1/2分谐波失真。采用以位敏探测器作为光电传感器的激光三角法实验观测扬声器振膜的振动位移和模态,确定了参与的非轴对称模态的周向波数。采用多尺度法求解了扬声器的非线性模态方程。给出了扬声器分谐波的阈值电压公式。结果表明扬声器辐射体薄壳的分谐波失真源于直接激励的轴对称模态耦合激发了非轴对称模态的振动,这种耦合激励表现为参数激励。增大扬声器振膜材料的损耗因子、杨氏模量和厚度可提高产生分谐波的阈值电压。      

考虑电感特性的扬声器线性参数辨识

当扬声器单元在其有效频率范围内所体现出的电感特性不可忽略时,采用纯电阻模型进行线性参数辨识得到的直流电阻辨识结果会与测量值产生较大偏差。根据对单元电感特性的讨论,建立了考虑等效电感的离散时间系统模型,推导了基于IIR自适应滤波器实现对直流电阻和等效电感辨识的迭代公式,并通过实验给出了与采用纯电阻模型进行参数辨识的结果对比,结果对比表明考虑电感的模型可以更为有效和稳定地实现对扬声器单元直流电阻的实时辨识。     

磁流体扬声器特性的分析

本文分析了磁流体扬声器的特性并给出一些实验结果.磁流体可以提高扬声器的功率容量,防止音圈过热损坏.磁流体扬声器的输入电功率在音圈温度相同的条件下,比同类普通扬声器可以提高2倍多,从而增加了扬声器的声压灵敏度.磁流体的粘滞性具有阻尼音圈振动的作用,它改善了扬声器的频响,降低瞬态畸变.文中还讨论了磁流体扬声器设计中应注意的问题.     

有内共振时的扬声器分谐波和混沌

研究了当轴对称模态由驱动力共振激发,并且轴对称模态和非轴对称模态存在2:1内共振时的扬声器辐射体薄壳的分谐波和昆沌。采用多尺度法分析了非线性模态方程的稳态解及其稳定性,由此进一步确定了驱动频率和驱动力平面上的分岔集。给出了所考虑情形下扬声器分谐波的阈值电压公式,该阈值电压低于无内共振时的阈值电压。除出现非轴对称模态的1/2分谐波振动外,2个模态的振幅经Hopf分岔后作极限环运动,并经倍周期分岔进入混沌运动。混沌出现是由于2个模态间能量的强烈交换。理论结果和实验结果基本吻合,该一致性表明了所建扬声器非线性薄壳模型的正确性。      

扬声器定心支片的非线性失真研究

本文在扬声器线性失真产生原因的分析基础上,设计了一种测量扬声器位移的新方法,并以大量的实验数据证明,大扬声器的结构中,定心支片的力学性能对扬声器非线性失真有极大地影响,指出于扬声器定心支片的研究,将有望成为一项新的课题。     

一种基于特征点提取的扬声器异常声检测方法

针对短时傅里叶变换在扬声器异常声检测中有效信息提取的随机性问题,提出了特征点法在扬声器异常声检测中的应用.此方法基于扬声器经扫频信号激励所得响应信号的短时傅里叶变换时频图,用改进的尺度不变特征转换算法对合格扬声器与异常声扬声器做特征提取,并将多组特征点经分割剔除后叠加组成特征矩阵模板.以合格扬声器样本提取特征曲线阈值构...     

气流扬声器振动系统的设计原理

本文用等效电路方法分析了电动气流扬声器振动系统的特性,求得了气流扬声器的输入阻抗和位移振幅的频率特性,并把结果用于典型扬声器,说明用等效电路分析指导气流扬声器设计的作用。气流扬声器振动系统所需的电功率与其机械共振频率的四次方成正比,其声辐射主要限于共振频率以下,因而高频特性较差。求得了在共振频率以下,频率响应平直的最佳条件,实验表明,在最佳条件下,气流扬声器的高频特性随着磁隙中的磁感应强度的增加仍稍有提高。实验结果符合理论分析,测得气流扬声器喇叭喉部的声压级在不同情况下达181分贝或184.8分贝(零分贝等于2×10^-5牛顿/米²)。     

扬声器的特性不匹配对虚拟声像的影响

本文从理论和实验上探讨了扬声器的特性不匹配对重放虚拟声像的影响。结果表明,用两扬声器进行虚拟听觉重放时,在某些频率段和虚拟声像角度,两扬声器间很小的幅频特性差异或相频特性差异都足以对虚拟声像方向产生明显的影响。扬声器特性的差异对前方范围的声像影响较小,但对侧向范围的声像影响较大,因而两扬声器的特性不匹配也是导致虚拟听觉重放时侧向声像位置畸变的重要原因之一。而在实际应用中要特别注意两扬声器的特性匹配,或者要用信号处理的方法对两扬声器的特性进行校正。     

直接辐射式扬声器系统的低频效率计算公式*

效率是扬声器系统的重要性能指标,然而常用的标称效率在低频范围并不适用。本文研究直接辐射式扬声器系统的低频效率,推导了基于TS参数的低频效率计算公式。针对封闭式扬声器系统和倒相式扬声器系统,开展实验验证,结果表明本文提出的计算公式得到的低频效率与实验测量得到的低频效率较为相符。进一步对比分析低频效率和标称效率,结果表明低频效率能够适用于低频,能准确地展示扬声器系统参数对效率的影响。利用本文提出的计算公式,有助于进一步优化提升扬声器系统的低频效率。     

Analytical solutions for axisymmetric vibration of loudspeaker cones in transitional range

The loudspeaker cone vibration in the transitional frequency range in which the governing equations have transition or turning points is studied by applying the uniformly valid solutions obtained in a previous paper. The solutions are presented analytically as well as the resonant and anti-resonant frequency equations, the associated patterns and the axial admittance. A new frequency equation for the non-bending effect is obtained. The results agree well with numerical results.     

扬声器锥壳的全频段强迫振动解

解析和数值研究了扬声器锥壳全频段的轴对称强迫振动。给出了典型低频段、典型转点频段和典型高频段的显式位移解析解、特征频率方程和轴向导纳表达式。解析结果与数值计算和实验结果结果非常吻合。在典型低频段,振动完全是纵波型的。在典型转点频段,全域的纵波运动和转点外侧域的横波运动共存,谐振和反谐振频率方程相应呈现出无矩解和弯曲解的耦合特性。在典型高频段,全域的纵波运动和横波运动互相独立,相应出现2组独立的纵波和横波固有频率。      

空心锥状双高斯光束传输特性研究

建立了空心锥状双高斯光束的模型.在空心高斯光束模型的基础上,由初始光场的光强分布,利用柱坐标下的柯林斯公式,导出了空心锥状双高斯光束经过傍轴光学系统的解析传输变换式由传输变换式计算分析了空心锥状双高斯光束在自由空问的可控传输特性,及在1,10和60 m的截面光环的光强分布.用KNbO3双轴晶体进行实验,获得了空心锥状双高斯光束,外锥折射的锥角等于入射光会聚角.实验表明,当空心光束处于锥状发射状态时,空心光束的光环内黑斑面积随传输距离的增加而增加,实验结果与模型吻合较好.该研究为进一步设计制备基于空心锥状舣高斯光束的新型激光元件提供了理论依据和设计参量.     

An electro-acoustics impedance error criterion and its application to active noise control

Characteristics of radiation impedance and its inducing variation of electrical impedance for a controllable source have been investigated. An impedance-based error criterion has been proposed and its application to active noise control is demonstrated through a coil driven loudspeaker. A general formula of radiation impedance is derived for two control strategies, according to the criterion of total acoustic power output. The radiation impedances of some commonly used sound sources are calculated. We discuss in detail the relation between variation of the input electrical impedance and radiation impedance for the two control strategies. An AC-bridge circuit is designed to measure the weak variation of electrical impedance resulted from radiation impedance. The input electrical impedance of a loudspeaker was measured and the experimental result is consistent with that of theoretical analysis. An impedance-based error criterion is proposed since the AC-bridge relative output is unique for a certain control strategy. The implementation of this criterion applied to an active control system is analyzed by simulations. An analogue control system is set up and experiments are carried out in a semi-anechoic chamber to verify the new control approach.     

Resonance identification in loudspeaker driver units: A comparison of techniques

A number of techniques with the scope of identifying loudspeaker cone resonances have been examined. Namely, the waterfall plot, the wavelet transform and the empirical mode decomposition scheme were compared on the basis of time-frequency resolution and damping estimation. The commonly used waterfall plot is only acceptable at the upper range of the acoustic spectrum. The wavelet transform is especially well suited for the analysis of transient signals from loudspeakers and is a significant improvement over the waterfall method. The newly developed EMD scheme has the highest potential in separating the modal components. By application of the EMD both instantaneous amplitude and frequency can be accurately determined.     

Measuring short impulse responses with inverse filtered maximum-length sequences

Most loudspeakers have a non-flat frequency response which produces a long oscillating impulse response. An inverse filtering approach may be used to calculate the driving waveform necessary to equalize the response of the loudspeaker in order to radiate shorter acoustic pulses. When combined with the MLS technique, inverse filtering may be used to pre-emphasize the driving signal so that a shorter impulse response, with a prescribed waveform, is measured. This technique is described and illustrated by applying it to a distributed mode loudspeaker. Originally, this loudspeaker has a rather irregular response in a wide band. When the MLS signal is pre-emphasized with the proper inverse filter, a shorter impulse response is measured with a zero-phase cosine-magnitude spectrum.     

Generalization of the Larmor radiation formula

The Larmor radiation formula relates the momentum radiated toward infinity along a light cone from a single point charge to the velocity and acceleration of the particle. The formula applies only to a light cone whose apex is on the world line of the particle. This paper generalizes the Larmor formula to an arbitrary light cone. An example involving circular motion is worked.     

A comprehensive discrete-time computer modeling of acoustic Transmission Line loudspeakers

The Transmission Line loudspeaker is an audio loudspeaker enclosure topology devoted to extending the low frequency range near the loudspeaker frequency resonance. A few models based on physical properties of damped pipes have been proposed to characterize the Transmission Line loudspeaker systems. Unfortunately, Thiele/Small parameters, which are usually employed in enclosure designs, are not useful as parameters of design for these loudspeakers. In this paper, a comprehensive numerical formulation of a Transmission Line loudspeaker is presented, which is based in a finite difference approach of the governing equations, including the effects of the absorbing material allocated inside the pipe. The influence of the main empirical parameters is tested on the proposed model, which is also compared to a real prototype for validation purposes.