TODGA/[C2mim][NTf2]萃取Th4+的研究

研究了N,N,N',N'-四辛基-3-氧戊二酰胺(TODGA)溶于疏水性离子液体咪唑类离子液体1-乙基-3-甲基咪唑双三氟甲磺酰亚胺盐([C₂mim][NTf₂])中对硝酸水溶液体系中四价钍离子(Th⁴⁺)的萃取行为.详细考察了接触时间、酸度、Th⁴⁺浓度、TODGA浓度、温度对TODGA/[C₂mim][NTf₂]体系萃取性能的影响.作为对比,我们还考察了TODGA在传统有机溶剂异辛烷中对Th⁴⁺的萃取.结果表明:TODGA/[C₂mim][NTf₂]体系对Th⁴⁺的萃取是吸热反应,且在50 ℃下,能在5 min内达到平衡.萃取体系随着酸度对Th⁴⁺的萃取性能先降后增大;Th⁴⁺浓度的增大,TODGA浓度的降低,对Th⁴⁺的萃取性能下降.TODGA在离子液体萃取体系中比在有机体系中有更好的Th⁴⁺萃取效果,特别是在低酸条件下.通过萃取机理研究,推测出在低酸下萃取反应是离子交换且TODGA与Th⁴⁺配比为2∶1,在高酸下萃取是中性配位.     

ApoCopC与汞（II）结合性质的光谱研究

在室温, pH 7.4, 10 mmol•L^-1Hepes（N-2-hydroxyethylpiperazine-N’-2-ethane-sulfonic acid）缓冲溶液条件下，通过紫外光谱法研究了apoCopC与汞（II）的结合性质。结果表明apoCopC的N，C- 端均可结合汞（II），且测得条件结合常数分别为K_n=(6.79 ± 1.12)´10⁶ mol^-1•L和K_c= (3.06±0.05)´10⁵ mol^-1•L。在pH 7.4，50 mmol·L^-1Hepes缓冲溶液条件下，用荧光光谱法研究了apoCopC的脲变性性质。结果表明汞（II）的结合对蛋白结构的维系具有稳定作用，并测得Hg_N²⁺-CoC-Hg_c²⁺ 和apoCopC的稳定吉布斯自由能（ΔG_D^H2O）分别为14.69±0.85 kJ•mol^-1和 16.66±0.55 kJ•mol^-1。     

γ-AlOOH/Al2O3修饰硅藻土的制备与Cs+、Pb2+吸附性能

以结晶氯化铝(AlCl₃·6H₂O)作为铝源,十二烷基苯磺酸钠(SDBS)为模板剂,采用水热法在硅藻土盘上制备了束状纳米结构γ-AlOOH/Al₂O₃复合吸附剂。采用XRD、SEM、TEM、TG/DSC、N₂吸脱附等对样品进行了表征。研究了样品对¹³³Cs⁺及Pb²⁺的吸附能力。研究表明,样品γ-AlOOH/硅藻土、γ-Al₂O₃/硅藻土对Cs⁺及Pb²⁺均具有良好的吸附性能,两者对Cs⁺的去除率分别为98.9%和99.6%;对Pb²⁺的最大吸附量分别为357.1、416.7mg·g^-1。两种样品对Pb²⁺的吸附均符合Langmuir吸附模型。     

CaSb2O6:Bi3+,Eu3+荧光粉的制备和发光性质

采用共沉淀法及1 200 ℃后续煅烧4 h,成功制备了CaSb₂O₆:Bi³⁺,Eu³⁺荧光粉,并对其结构及发光性能进行了研究。所制备荧光粉颗粒为六边形类圆饼状,平均尺寸在100~600 nm之间。对CaSb₂O₆:Bi³⁺,Eu³⁺发光的机理分析表明,Bi³⁺对Eu³⁺的发光存在高效的敏化与能量传递。当Bi³⁺和Eu³⁺的掺杂浓度分别为0.5%和8%,Eu³⁺位于580 nm(⁵D₀→⁷F₀ )处的荧光发射显著增强,Bi³⁺,Eu³⁺共掺样品的荧光强度是CaSb₂O₆:Eu³⁺的10倍左右。调节Bi³⁺/Eu³⁺离子掺杂比,色坐标呈现了从蓝、白光到红光的变化,表明该荧光粉可分别作为蓝或红色荧光粉使用,甚至可实现从蓝、白光到红光的自由调控,这为白光LED荧光粉的发展提供了参考。     

Vacancy Contents in MnZn Ferrites From TG Curves

Expressions for calculating the cation vacancy contents of MnZn ferrites from thermogravimetric curves are presented together with some experimental data. In a single-phase MnZn ferrite synthesized by conventional ceramic procedures, the O₂ evolution accompanying ferrite formation follows the formal equation. Mn²⁺ _σα Zn_σβ Fe³⁺ _2σ(1–γ) [V ]_{σ/4(1–2γ)} O₄ =σ'/σ Mn²⁺ _σ(α–2ϕ) Zn_σβ Fe²⁺ _2σθ Mn³⁺ _2σϕ Fe³⁺ _{2σ(1–γ–θ)} [V ]_{σ/4(1–2γ–3ϕ)} O₄ +σ'φ/2O₂ (g) where α and β denote the MnO and ZnO mole fractions in the primary mixture γ=α+β, θ and ϕ depend on the quantities of Fe²⁺ and Mn³⁺ formed, respectively, φ=θ–ϕ and σ'/σ is a function of the former parameters. Even though the relative amounts of Fe²⁺ /Fe³⁺ and Mn²⁺ /Mn³⁺ remain uncertain, the vacancy content [V ] of the ferrite can be determined because it depends on φ alone, which is related to the change in mass of the sample as the synthesis takes place through the equation φ=(1.5–γ) μ_β /μ_O2 (1–m _f /m _i ) Here, m _i and m _f are the masses of the sample before and after O₂ evolution, μ_B is the formula mass of the ferrite and μ_O2 is the O₂ molar mass. Practically vacancy-free single-phase MnZn ferrite samples were obtained by sintering in air at 1250°C and cooling in pure N₂ . This revised version was published online in July 2006 with corrections to the Cover Date.     

A Binuclear Copper(II) Complex with Two Symmetric End-on Azido Bridges. Synthesis, Spectroscopy, Crystal Structure and Magnetism

A binuclear copper(II) complex with two symmetric end-on azido bridges: [Cu₂(tacn)₂(μ-N₃)₂](ClO₄)² · CH₃OH (1), where tacn = 1,4,7-triazacyclononane, has been synthesized and structurally as well as magnetically characterized. Compound (1) has the discrete binuclear structure, bridged by two end-on N₃⁻ anions. The macrocyclic ligand tacn functions as a terminal ligand. The magnetic data of compound (1) were analyzed by means of Ĥ = −2JŜ₁Ŝ₂ − DŜ_z, leading to J = 2.49 cm⁻¹, g = 2.08, D = ±0.97 cm⁻¹, zJ′ = −0.47 cm⁻¹. The ferromagnetic interaction is discussed on the basis of the structural features and is compared with the model structure of Ruiz.     

Ce3+掺杂La2O3的17O固体核磁共振研究

本文用水热共沉淀法制备Ce³⁺掺杂La₂O₃的前驱体,随后在H₂/N₂气氛下用高温煅烧法合成了不同Ce³⁺浓度的掺杂La₂O₃。由于Ce³⁺的掺杂,¹⁷O固体核磁共振谱图中在698、650和558处出现了新的共振峰;随着Ce³⁺掺杂浓度的增加,这些峰的强度也随之增强。根据谱峰位置和强度,对谱图进行了归属：698、650处的共振峰应源自与Ce³⁺相连的四配位O(OCeLa₃),558处的信号则来自于与Ce³⁺相连的六配位O(OCeLa₅)。通过¹⁷O固体核磁共振能够直接观测与Ce³⁺直接相连的O显示该方法将可能用于研究稀土掺杂氧化物功能材料。     

酚氧桥联多核铜(Ⅱ)配合物的合成、结构和磁性

利用柔性酚胺类配体N,N'-二甲基-N,N'-(2-羟基-4,5-二甲基苄基)乙二胺(H₂L)与Cu(Ⅱ)反应,合成了2个新的酚氧桥联多核Cu(Ⅱ)配合物[Cu₃^II(L)₂(CH₃OH)₂](ClO₄)₂(1),[Cu₃^II(L)₂(Cu^ICl₂)₂](2)。配合物1~2中,3个Cu²⁺之间通过2个酚氧桥连接,形成线性三核结构。两边的铜离子分别被配体L^2-上的N₂O₂螯合配位,轴向与甲醇分子的氧(配合物1)或[CuCl₂]^-的氯(配合物2)配位,形成四方锥配位构型。中间铜离子与两侧L^2-上的4个酚氧原子以平面四边形配位。Cu^II-O-Cu^II键角为100.14°~101.79°。对配合物1~2进行变温磁化率测量表明,铜离子之间通过酚氧桥存在强的反铁磁耦合,磁耦合常数J分别为-277(9)cm^-1(配合物1)和-299(3)cm^-1(配合物2)(基于自旋哈密顿算符Ĥ=-2J(Ŝ₁·Ŝ₂+Ŝ₂·Ŝ₃)。J值与酚氧桥桥联键角有一定相关性,即Cu-O-Cu桥联键角越大,反铁磁耦合越强。     

Ce3+掺杂La2O3的17O固体核磁共振研究

本文用水热共沉淀法制备Ce³⁺掺杂La₂O₃的前驱体,随后在H₂/N₂气氛下用高温煅烧法合成了不同Ce³⁺浓度的掺杂La₂O₃。由于Ce³⁺的掺杂,¹⁷O固体核磁共振谱图中在698、650和558处出现了新的共振峰;随着Ce³⁺掺杂浓度的增加,这些峰的强度也随之增强。根据谱峰位置和强度,对谱图进行了归属:698、650处的共振峰应源自与Ce³⁺相连的四配位O(OCeLa₃),558处的信号则来自于与Ce³⁺相连的六配位O(OCeLa₅)。通过¹⁷O固体核磁共振能够直接观测与Ce³⁺直接相连的O显示该方法将可能用于研究稀土掺杂氧化物功能材料。     

GdPO4:Sm3+荧光粉的焙烧温度和掺杂浓度的优化及发光和磁性能

以GdPO₄为基质,Sm³⁺为激活剂,采用水热法合成了纳米荧光粉前驱体,分别在800、900、1 000、1 100和1 200℃下焙烧,得到一系列GdPO₄:Sm³⁺荧光粉。首先探究了GdPO₄:Sm³⁺的最佳焙烧温度;其次研究了Sm³⁺掺杂浓度对GdPO₄:Sm³⁺荧光性能的影响;最后研究了GdPO₄:2% Sm³⁺的高温荧光性能和磁性能。使用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、磁强计和荧光分光光度计(FL)对荧光粉的晶体结构、形貌、发光和磁性能进行了表征。结果表明:荧光粉的晶体结构由前驱体六方晶系GdPO₄·H₂O:Sm³⁺变为单斜晶系的GdPO₄:Sm³⁺,形貌由纳米棒变为无规则块体。当焙烧温度为1 000℃,Sm³⁺掺杂浓度为2%时,荧光粉的发光强度和荧光寿命达到最大值。GdPO₄:2% Sm³⁺中Sm³⁺之间能量传递类型为电偶极-电偶极相互作用,能量传递的临界距离为1.646~1.884 nm。最佳样品GdPO₄:2% Sm³⁺有优异的热稳定性,热猝灭活化能为-0.157 eV,且具有良好的顺磁性,质量磁化率为1.22×10^-4 emu·g^-1·Oe^-1。     

Rubber networks containing unattached macromolecules. II. Viscoelastic properties in small strains of the system ethylene–propylene terpolymer with ethylene–propylene copolymer

Mixtures of crosslinkable ethylene–propylene terpolymer with saturated ethylene–propylene copolymer (molecular weights 3.6, 16.7, and 45 × 10⁴) containing up to 50% by weight of copolymer were crosslinked by sulfur, leaving the saturated copolymer unattached and free to reptate in the terpolymer network. Stress relaxation in small simple elongations (stretch ratio about 1.15) and dynamic Young's modulus at frequencies from 3.5 to 110 Hz were measured at temperatures from 10 to 50°C. Comparison with the properties of the terpolymer crosslinked without added copolymer showed contributions to stress relaxation and mechanical loss attributable to the unattached species. The time required in stress relaxation for the portion of the modulus attributable to the unattached species to decay to half its plateau value, t_1/2, is approximately proportional to the 3.5 power of the molecular weight; t_1/2 appears to be slightly smaller for networks containing 50% than for those containing 25% unattached component.     

A Bis(phenoxy‐imine)Zr Complex for Ultrahigh‐Molecular‐Weight Amorphous Ethylene/Propylene Copolymer

A new bis(phenoxy‐imine)Zr complex has been developed. This complex in conjunction with ⁱBu₃Al/Ph₃CB(C₆F₅)₄ at 70°C produces ultrahigh‐molecular‐weight amorphous ethylene/propylene copolymer with a weight‐average molecular weight of 10 200 000 g/mol versus polystyrene standards, which represents the highest molecular weight known for linear, synthetic copolymers to date.     

Synthesis of amphiphilic poly(methyl methacrylate‐ b‐ethylene oxide) copolymers from monohydroxy telechelic poly(methyl methacrylate) as macroinitiator

The synthesis of well‐defined poly(methyl methacrylate)‐block‐poly(ethylene oxide) (PMMA‐b‐PEO) dibock copolymer through anionic polymerization using monohydroxy telechelic PMMA as macroinitiator is described. Living anionic polymerization of methyl methacrylate was performed using initiators derived from the adduct of diphenylethylene and a suitable alkyllithium, either of which contains a hydroxyl group protected with tert‐butyldimethylsilyl moiety in tetrahydrofuran (THF) at ?78 °C in the presence of LiClO₄. The synthesized telechelic PMMAs had good control of molecular weight with narrow molecular weight distribution (MWD). The ¹H NMR and MALDI‐TOF MS analysis confirmed quantitative functionalization of chain‐ends. Block copolymerization of ethylene oxide was carried out using the terminal hydroxyl group of PMMA as initiator in the presence of potassium counter ion in THF at 35 °C. The PMMA‐b‐PEO diblock copolymers had moderate control of molecular weight with narrow MWD. The ¹H NMR results confirm the absence of trans‐esterification reaction of propagating PEO anions onto the ester pendants of PMMA. The micellation behavior of PMMA‐b‐PEO diblock copolymer was examined in water using ¹H NMR and dynamic light scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2132–2144, 2008     

Unimodal molecular weight distribution of commercial polymers from viscoelastic data

This article presents a method that provides the molecular weight distribution (MWD) of polymeric material from rheological data. The technique has been developed to deal with linear polymers with a log‐normal molecular weight distribution. The rheological data must include the shear storage modulus, G′(ω), and the shear loss modulus, G″ (ω), ranging from the terminal zone to the rubberlike zone. It was not necessary to achieve the relaxation spectrums via the extremely unstable problem of inverting integral equations. The method has been tested with different polymers (polydimethylsiloxane, polyisoprene, random copolymer of ethylene and propylene, and polystyrene) and the calculated MWDs were in good agreement with experimental data. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1539–1546, 2000     

Copolymerization of ethylene with 1‐hexene promoted by novel multi‐chelated non‐metallocene complexes with imine bridged imidazole ligand

A series of novel bridged multi‐chelated non‐metallocene catalysts is synthesized by the treatment of N,N‐imidazole, N,N‐dimethylimidazole, and N,N‐benzimidazole with n‐BuLi, 2,6‐dimethylaniline, and MCl₄ (M = Ti, Zr) in THF. These catalysts are used for copolymerization of ethylene with 1‐hexene after activated by methylaluminoxane (MAO). The effects of polymerization temperature, Al/M molar ratio, and pressure of monomer on ethylene copolymerization behaviors are investigated in detail. These results reveal that these catalysts are favorable for copolymerization of ethylene with 1‐hexene featured high catalytic activity and high comonomer incorporation. The copolymer is characterized by ¹³C NMR, WAXD, GPC, and DSC. The results confirm that the obtained copolymer features broad molecular weight distribution (MWD) about 33–35 and high 1‐hexene incorporation up to 9.2 mol %, melting temperature of the copolymer depends on the content of 1‐hexene incorporation within the copolymer chain and 1‐hexene unit in the copolymer chain isolates by ethylene units. The homopolymer of ethylene has broader MWD with 42–46. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 417–424, 2010     

Molecular‐Weight‐Dependence on Domain Formation of Grafted Poly(ethylene‐co‐propylene) in a Poly(propylene) Matrix

Several novel poly(propylene)‐graft‐poly(ethylene‐co‐propylene) copolymers with isotactic poly(propylene) (PP) backbones and ethylene/propylene rubber (EPR) branches were synthesized. The thermomechanical properties of these samples were investigated using a dynamic mechanical analyzer. There appeared to be a critical EPR molecular weight above which a two‐phase system developed with EPR domains dispersed in a PP matrix. This domain formation gave an enhanced loss modulus compared to a commercial high impact PP product below 40°C.     

Synthesis of ultra‐high‐molecular‐weight ethylene‐propylene copolymer via quasi‐living copolymerization with N‐heterocyclic carbene ligated vanadium complexes

The quasi‐living copolymerization of ethylene with propylene was achieved by using N‐heterocyclic carbene (NHC) ligated vanadium complex ( V3 , VOCl₃[1,3‐(2,6‐ⁱPr₂C₆H₃)₂(NCH?)₂C:]) due to the stabilization of active center by the introduction of bulky and electron rich NHC ligand with bulky isopropyl substituents at the ortho positions of the phenyl rings. The weight‐average molecular weight (M_w) of the resulting copolymer increases linearly with its weight in 20 min. The ultra‐high‐molecular‐weight (UHMW) ethylene‐propylene copolymer (M_w = 1612 kg mol^?1) can be synthesized with V3 /Et₃Al₂Cl₃ catalytic system. The novel complex V4′ (VCl₃[1,3‐(2,4,6‐Me₃C₆H₂)₂(NCH?)₂C:]·2THF) was constructed by the introduction of two coordinated tetrahydrofuran molecules and decrease in steric hindrance at the ortho positions of phenyl rings. The UHMW ethylene‐propylene copolymer (M_w = 1167 kg mol^?1) can also be synthesized by using V4′ /Et₃Al₂Cl₃ catalytic system. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 553–561     

Synthesis of new amphiphilic diblock copolymers containing poly(ethylene oxide) and poly(α‐olefin)

This article discusses an effective route to prepare amphiphilic diblock copolymers containing a poly(ethylene oxide) block and a polyolefin block that includes semicrystalline thermoplastics, such as polyethylene and syndiotactic polystyrene (s‐PS), and elastomers, such as poly(ethylene‐co‐1‐octene) and poly(ethylene‐co‐styrene) random copolymers. The broad choice of polyolefin blocks provides the amphiphilic copolymers with a wide range of thermal properties from high melting temperature ～270 °C to low glass‐transition temperature ～?60 °C. The chemistry involves two reaction steps, including the preparation of a borane group‐terminated polyolefin by the combination of a metallocene catalyst and a borane chain‐transfer agent as well as the interconversion of a borane terminal group to an anionic (? O^?K⁺) terminal group for the subsequent ring‐opening polymerization of ethylene oxide. The overall reaction process resembles a transformation from the metallocene polymerization of α‐olefins to the ring‐opening polymerization of ethylene oxide. The well‐defined reaction mechanisms in both steps provide the diblock copolymer with controlled molecular structure in terms of composition, molecular weight, moderate molecular weight distribution (M_w/M_n < 2.5), and absence of homopolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3416–3425, 2002     

Rubber networks containing unattached macromolecules. III. Nonlinear stress relaxation in the system ethylene–propylene terpolymer with ethylene–propylene copolymer and behavior of extracted networks

Further stress relaxation experiments, mostly at 50°C, are reported on mixtures of crosslinkable ethylene–propylene terpolymer with saturated ethylene–propylene copolymer (molecular weights 3.6 and 45 × 10⁴) containing up to 50% by weight of copolymer, crosslinked by sulfur to leave the saturated copolymer unattached and free to reptate in the copolymer network. Stress relaxation was measured in small simple elongations (stretch ratio about 1.15) on samples which had been extracted to remove a large part of the unattached copolymer and dried. The relative increase in modulus at long times (10⁴ sec) increased with the proportion extracted; at short times (1 sec), extraction of the lower molecular weight copolymer increased the modulus to about the same extent but extraction of the higher molecular weight copolymer affected it very little. The relaxation modulus of the copolymer extracted from sample 50H (50% copolymer of high molecular weight), obtained by difference, agreed with that for the total copolymer except for a small difference probably attributable to molecular weight selectivity in the extraction. Stress relaxation was measured on sample 50H at six higher elongations up to a stretch ratio of 3. The dependence of stress on time and strain was consistent with an analysis based on the following assumptions: (a) linear additivity of the network and unattached copolymer contributions, (b) strain–time factorization of the stress contributions from the individual components, (c) a strain dependence for the unattached component corresponding to the presence of a Mooney–Rivlin C₂ term only, (d) a strain dependence for the network component which does not follow the Mooney–Rivlin equation but is dominated by a simple neo-Hookean term.     

Copolymerization of ethylene or propylene with α‐olefins containing hydroxyl groups with zirconocene/methylaluminoxane catalyst

Copolymerization of olefins (ethylene and propylene) and 5‐hexen‐1‐ol pretreated with alkylaluminum was performed using [dimethysilylbis(9‐fluorenyl)]zirconium dichloride/methylaluminoxane as the catalyst. The copolymerization required extra addition of alkylaluminum to prevent deactivation of the catalyst when 5‐hexen‐1‐ol was pretreated with trimethylaluminum, whereas the triisobutylaluminum‐treated system did not require any addition of alkylaluminum. The molecular weight of the copolymer depended on the kind of alkylaluminum compound (masking reagent, additive, and cocatalyst). ¹³C NMR analysis proved that poly(ethylene‐co‐5‐hexen‐1‐ol) containing 50 mol % of 5‐hexen‐1‐ol acted as an alternating copolymer, whereas the poly(propylene‐co‐5‐hexen‐1‐ol) acted as a random copolymer. The surface property of the copolymers was simply evaluated by means of water drop contact angle measurement. It was found that the copolymers containing large amounts of 5‐hexen‐1‐ol units showed good hydrophilic properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 52–58, 2004