Photosensitization of vinyl polymerization by uranyl ions

Monomer acrylamide was used as quencher of uranyl ion fluorescence and Stern-Volmer plots were constructed at three monochromatic wavelengths of exciting radiation. The results indicated that the reaction between excited uranyl ion and monomer is one of energy transfer. The rate parameters k_p/k_p^½ and k_d′/k_i were calculated from the polymerization kinetics at high monomer concentrations. A general mechanism for the photopolymerization of vinyl monomers sensitized by uranyl ions is proposed and discussed.     

Photopolymerization of vinyl monomers in the presence of chlorosilane compounds

The photopolymerization of vinyl monomers (methyl methacrylate and styrene) was investigated in the presence of chlorosilane compounds. It was found that these additives acted as photosensitizers. In the case of the photopolymerization of methyl methacrylate, the rate of polymerization was found to be proportional to the concentration of methyl methacrylate and to the square root of the chlorosilane concentration. The chain-transfer constants of these photosensitizers, SiCl₄, CH₃SiCl₃, (CH₃)₂SiCl₂, (CH₃)₃-SiCl, and (CH₃)₄Si, with ultraviolet irradiation were 25.6 × 10^?3, 18.4 × 10^?3, 17.5 × 10^?3, 14.4 × 10^?3 and 0.5 × 10^?3, respectively, for methyl methacrylate.     

Photopolymerization with the use of titanocene dichoride as sensitizer

Titanocene dichloride sensitized photopolymerization of vinyl ethers and styrene but did not polymerize methyl methacrylate and vinyl acetate. In the case of 2-chloroethyl vinyl ether, polymerization started rapidly some time after the color of the liquid had changed from orange to green. Polymerization was also achieved by heating the monomer at 60°C after stopping the irradiation at the end of the induction period. On the basis of the reactivity of the monomers and the effect of additives, polymerization is considered to proceed cationically. In case of the polymerization of styrene, conversion increased linearly with time. The k/k_t value of 6.3 × 10^?5l./mole-sec obtained for the polymerization of styrene agrees well with the value reported for radical polymerization. The agreement of the value and ineffective inhibition of polymerization in the presence of pyridine indicates the polymerization follows a radical mechanism. Copolymerization of styrene (M₁) and 2-chloroethyl vinyl ether (M₂) proceeded radically, and the reactivity ratios were r₁ = 2.5 and r₂ = 0.6.     

Vinyl polymerization. Part 268. Polymerization of acrylonitrile initiated by the system of tetramethyl tetrazene and bromoacetic acid

The polymerization of acrylonitrile (AN) initiated by the system of tetramethyl tetrazene (TMT) and bromoacetic acid (BA) in dimethylformamide (DMF) was studied. The TMT–BA system could initiate the polymerization of AN more easily than TMT alone. The polymerization was confirmed to proceed through a radical mechanism. The initial rate of polymerization R_p was expressed by the equation: R_p = [TMT]^0.62-[BA]^0.5[AN]^1.5. The overall activation energy for the polymerization was estimated as 9.4 kcal/mole. In the absence of monomer, the reaction of TMT with BA in DMF was also studied kinetically by measuring the evolution of nitrogen gas. The reaction was first-order in TMT and first-order in BA; the rate data at 49°C were k₂ = 9.1 × 10^?2l./mole-sec., ΔH? = 17.0 kcal/mole, and ΔS? = ? 6.6 eu. In addition, the treatment of TMT with BA in benzene led to the formation of tetramethylhydrazine radical cation, which was identified by its ESR spectrum. On the other hand, the relatively strong interaction between TMT and DMF was observed by absorption spectrophotometry.     

Vinyl monomers bearing chromophore moieties and their polymers. IV. Fluorescence and photosensitizing behavior of 8-acryloyloxyquinoline and its polymer

Acrylic monomers bearing electron-donating quinolyl moiety, i.e., 8-acryloyloxyquinoline (AQ) was prepared and polymerized. It was found that the fluorescence intensity of AQ was much lower than that of P(AQ) at the same chromophore concentration. The fluorescence of P(AQ) could be quenched by electron-deficient vinyl monomers, such as acrylonitrile (AN) and methyl methacrylate (MMA). This is another example of the “fluorescence structural self-quenching effect” termed by us previously, and demonstrates again that this phenomenon is not an accidental but a general one for acrylic monomers bearing electron-donating chromophores. The photopolymerization of acrylonitrile (AN) sensitized by AQ and P(AQ) as well as combining with carbon tetrabromide (CBr₄) was studied kinetically. From the rates of the polymerization (R_p) and overall activation energies obtained for these four systems, it was found that R_p sensitized by the binary systems was much higher than by AQ or P(AQ) alone, while the molecular weights of the resulting P(AN) were lower. The fluorescent analysis of the resulting P(AN) in solution showed that the sensitizers also entered into the P(AN) chains. A mechanism of charge transfer complex (CTC) formation was tentatively suggested for the photopolymerization of AN initiated by these four systems. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1087–1093, 1997     

Fluorinated vinyl ethers as new surface agents in the photocationic polymerization of vinyl ether resins

The syntheses of fluorinated vinyl ethers (H₂C?CHOCH₂CH₂C_nF_2n+1, n = 6 or 8) and their copolymerizations with bis(4‐vinyloxybutyl) isophthalate are reported. The fluorinated monomers were prepared by the transetherification of ethyl vinyl ether and fluorinated alcohols in a 75% yield. Added in low concentrations (0.1–3.0 wt %) to formulations containing bis(4‐vinyloxybutyl) isophthalate, they did not affect the kinetics of the cationic photopolymerization. The cured films were transparent and showed interesting properties in terms of wettability, hardness, cross‐cut adhesion, and chemical inertness. The fluoromonomers increased the hydrophobicity of the film surface, whereas the adhesion on various substrates such as glass and wood was unchanged. An increase in the methyl ethyl ketone resistance was also observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2890–2897, 2003     

STRUCTURAL EFFECT ON VINYL POLYMERIZATION INITIATED WITH AROMATIC TERTIARY AMINE

The polymerization mechanism of various vinyl monomers in the presence of aromatic tertiary amines has been studied. It was found that the mechanisms of different monomers are varied with the structures of monomers. Those monomers, such as methacrylic esters containing α-CH_3 group on the double bond could be polymerized with aromatic tertiary amine in the absence of light, while the monomers without α-CH_3 group, such as methyl acrylate, acrylonitrile etc. would polymerize only under light.The structural effects, both of the monomer and the amine, on the rate of photopolymerization were studied. The activities of monomers and amines may be arranged in the following orderMonomer: AN>MA>VA>St Amine: DMT>DMA>DMB>DNAIt is revealed that both the electro-negative group on the double bond of monomer which acts as an acceptor and the electro-positive group on the nitrogen atom of amine which acts as a donor would effectively increase the rate of photopolymerization.     

Vinyl polymerization photosensitized by anthraquinone sulfonates in aqueous solutions

The kinetics of the photopolymerization of the vinyl monomers MMA and MA sensitized by anthraquinone sulfonate-NaCl-HClO₄ systems have been studied systematically. The wavelength 365 mμ was used for irradiation. Sodium anthraquinone-2-sulfonate and disodium anthraquinone-2,6-disulfonate were used as sensitizers, and all experiments were conducted in deaerated conditions. The polymerization was followed by the measurement of monomer disappearance (gravimetrically), rate of sensitizer disappearance (spectrophotometrically) and the chainlength of the polymer formed (viscometrically). Monomer concentration, k_ε, [NaCl], and I were varied. In the light of the experimental results a prima facie kinetic scheme was proposed. The specific rate constants for the various steps have been evaluated.     

Graft polymers: Chain transfer and branching

The vinyl monomers, methyl methacrylate, ethyl methacrylate, and methyl acrylate were polymerized in the presence of chlorinated rubber or poly(vinyl chloride) in homogeneous solution with benzoyl peroxide as catalyst. A graft polymer was formed by a chain-transfer reaction involving the growing polymer radicals to the backbone of chlorinated rubber or poly(vinyl chloride), in addition to homopolymer from the monomer. The homopolymer was isolated from the polymer mixture by fractional precipitation from methyl ethyl ketone solution with methanol as precipitant. The chain-transfer constants for the branching reactions were evaluated. The ratios k_p/(k_t)^1/2 for the grafting reactions were obtained by a correlation of chain-transfer constants with the extent of branching. The chain-transfer data were correlated on the basis of an extension of the Q–e scheme of Alfrey and Price to polymer–polymer transfer reactions. Specific effects due to the backbone are found to have considerable influence on the course of the chaintransfer reactions and k_p/(k_t)^1/2 of the grafting reactions.     

Radical copolymerization of 2‐trifluoromethylacrylic monomers. II. Kinetics,monomer reactivities,and penultimate effect in their copolymerization with norbornenes and vinyl ethers

Radical copolymerizations of electron‐deficient 2‐trifluoromethylacrylic (TFMA) monomers, such as 2‐trifluoromethylacrylic acid and t‐butyl 2‐trifluoromethylacrylate (TBTFMA), with electron‐rich norbornene derivatives and vinyl ethers with 2,2′‐azobisisobutyronitrile as the initiator were investigated in detail through the analysis of the kinetics in situ with ¹H NMR and through the determination of the monomer reactivity ratios. The norbornene derivatives used in this study included bicyclo[2.2.1]hept‐2‐ene (norbornene) and 5‐(2‐trifluoromethyl‐1,1,1‐trifluoro‐2‐hydroxylpropyl)‐2‐norbornene. The vinyl ether monomers were ethyl vinyl ether, t‐butyl vinyl ether, and 3,4‐dihydro‐2‐H‐pyran. Vinylene carbonate was found to copolymerize with TBTFMA. Although none of the monomers underwent radical homopolymerization under normal conditions, they copolymerized readily, producing a copolymer containing 60–70 mol % TFMA. The copolymerization of the TFMA monomer with norbornenes and vinyl ethers deviated from the terminal model and could be described by the penultimate model. The copolymers of TFMA reported in this article were evaluated as chemical amplification resist polymers for the emerging field of 157‐nm lithography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1478–1505, 2004     

Chain transfer for vinyl monomers polymerized in N-allylstearamide

Apparent transfer constants have been determined for styrene, methyl methacrylate vinyl acetate, and diethyl maleate polymerized in N-allylstearamide at 90°C. Regression coefficients for transfer were: methyl methacrylate, 0.301 × 10^?3; styrene, with no added initiator, 0.582 × 10^?3; styrene, initiated with benzoyl peroxide, 0.830 × 10^?3; vinyl acetate, 62.01 × 10^?3; and diethyl maleate, 2.24 × 10^?3. Rates of polymerization were retarded for both styrene and methyl methacrylate. Vinyl monomer and comonomer disappearance followed an increasing exponential dependence on both initiator and monomer concentration. Although degradative chain transfer probably caused most of the retardation, the cross-termination effect was not eliminated as a contribution factor. Rates for the vinyl acetate copolymerization were somewhat retarded, even though initiator consumption was large because of induced decomposition. The kinetic and transfer data indicated that the reactive monomers added radicals readily, but that rates were lowered by degradative chain transfer. Growing chains were terminated at only moderate rates of transfer. Unreactive monomers added radicals less easily, producing reactive radicals, which transferred rapidly, so that molecular weights were lowered precipitously. Although induced initiator decomposition occurred, rates were still retarded by degradative chain transfer. A simple empirical relation was found between the reciprocal number-average degree of polymerization, 1/X?_n1 and the mole fraction of allylic comonomer entering the copolymer F₂, which permitted estimation of the molecular weight of copolymers of vinyl monomers with allylic comonomers. This equation should be applicable when monomer transfer constants for each homopolymer are known and when osmometric molecular weights of one or two copolymers of low allylic content have been determined.     

Oxygen‐Triggered Switchable Polymerization for the One‐Pot Synthesis of CO2‐Based Block Copolymers from Monomer Mixtures

Switchable polymerization provides the opportunity to regulate polymer sequence and structure in a one‐pot process from mixtures of monomers. Herein we report the use of O₂ as an external stimulus to switch the polymerization mechanism from the radical polymerization of vinyl monomers mediated by (Salen)Co^III?R [Salen=N,N′‐bis(3,5‐di‐tert‐butylsalicylidene)‐1,2‐cyclohexanediamine; R=alkyl] to the ring‐opening copolymerization (ROCOP) of CO₂/epoxides. Critical to this process is unprecedented monooxygen insertion into the Co?C bond, as rationalized by DFT calculations, leading to the formation of (Salen)Co^III?O?R as an active species to initiate ROCOP. Diblock poly(vinyl acetate)‐b‐polycarbonate could be obtained by ROCOP of CO₂/epoxides with preactivation of (Salen)Co end‐capped poly(vinyl acetate). Furthermore, a poly(vinyl acetate)‐b‐poly(methyl acrylate)‐b‐polycarbonate triblock copolymer was successfully synthesized by a (Salen)cobalt‐mediated sequential polymerization with an O₂‐triggered switch in a one‐pot process.     

Design and synthesis of highly photopolymerizable styrenyl compounds in solid‐state photoinitiated polymerization

We designed a new type of styrenyl compound applicable to conventional photopolymerization systems, aiming at the production of polymers with improved mechanical properties, resistance to chemicals, and elevated glass‐transition temperatures (T_g's). A series of styrenyl monomers bearing 2,5‐dithio‐1,3,4‐thiadiazole groups were prepared, and their reactivity was studied in solid‐state photopolymerization initiated by 2‐(4′‐methoxystyryl)‐4,6‐bis(trichloromethyl)‐1,3,5‐triazine. These monomers exhibited much higher polymerization rates than usual, and the final conversion nearly reached completion, despite the relatively high T_g of the solid‐state photopolymerization system. Even at temperatures below T_g, the polymerization proceeded without a ceiling phenomenon. These features were explained by intermolecular interactions between the monomers that induced monomer alignments effective for solid‐state polymerization, large excess free volumes arising from rotation around the methylthio groups, and intramatrix radical migration leading to encounters with the remaining monomers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3227–3242, 2003     

Free-radical polymerization of vinyl ferrocene

The results of quantitative studies of the rates of free-radical polymerization of vinyl ferrocene indicate that the latter has polymerization characteristics similar to those of styrene. The rates of homopolymerization of these two monomers in benzene at 70°C. were measured with the use of azobisisobutyronitrile as catalyst. The rate constants (k = R_p/[M][I]^1/2) are k_VF = (1.1 ? 1.8) × 10^?4, k_STY = 1.65 × 10^?4. Small amounts of vinyl ferrocene and styrene have similar effects on the rates of polymerizations of methyl methacrylate and ethyl acrylate and on the molecular weights of the resulting polymer. Polystyrene and poly(vinyl ferrocene) with similar molecular weights are isolated from polymerizations carried out under identical conditions. The rates of copolymerization of vinyl ferrocene—methyl methacrylate, vinyl ferrocene—styrene, and styrene—methyl methacrylate were determined by following the disappearance of monomers by means of gas chromatographic analyses. The relative reactivity for vinyl ferrocene is slightly lower than that for styrene.     

Bisphosphonate units in the main polymer chain: The first synthesis

Radical copolymerization of tetraethyl vinylidene phosphonate ( B ) with vinyl monomers has been described for the first time. In copolymerization with vinyl acetate ( V ) strictly alternating copolymer was formed even when [ V ]₀/[ B ]₀ was equal to 80. In copolymerization with acrylic acid ( A ) copolymers of the general structure ‐[( B )₁ A _x)]_n‐ were formed. The number of A units (x) was shown to depend on the [ A ]₀/[ B ]₀ ratio in the monomers feed. The reactivity ratio r_A was determined as equal to 2.1 and on this basis, the distribution of x as a function of [ A ]₀/[ B ]₀ was found. Bisphosphonic units were deblocked and the corresponding polyacids were analyzed by NMR spectra. M_n > 0.5 × 10⁶ were measured by SEC for copolymers of B with A . © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Adding magnetic ionic liquid monomers to the emulsion polymerization tool‐box: Towards polymer latexes and coatings with new properties

Magnetic ionic liquid monomers were synthesized and then polymerized to get magnetic polymer latexes and films. First, a series of 1‐vinyl‐3‐dodecyl‐imidazolium monomers having metal halides counter‐anions such as FeCl₃Br^?, CoCl₂Br^?, and MnCl₂Br^? were synthesized. These ionic liquid monomers were first homopolymerized to lead to magnetic poly(ionic liquids) and characterized. Secondly, magnetic latexes were synthesized by using the magnetic ionic liquids as surfmers (surfactant + monomer) in the emulsion polymerization of methyl methacrylate/n‐butyl acrylate. It was found that the powders obtained by freeze‐drying the latexes presented a paramagnetic behavior with weak antiferromagnetic interactions between the adjacent metal ions. Although the ratio of magnetic ionic liquid/monomer was only 2% these poly(methyl methacrylate‐co‐butyl acrylate) powders and latexes responded to a magnetic field due to the surfmer paramagnetic nature. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1145–1152     

Chain transfer constants for vinyl monomers polymerized in methyl oleate and methyl stearate

Chain transfer constants were obtained for styrene, methyl methacrylate, methyl acrylate and vinyl acetate, polymerized in methyl oleate and methyl stearate at 60°C. Transfer constants increased in the order: methyl methacrylate < styrene < methyl acrylate ? vinyl acetate in both solvents. Average values of the transfer parameters were: for methyl oleate, Q_tr = 2.04 × 10^?4, e_tr = 1.08; for methyl stearate, Q_tr = 0.373 × 10^?4, e_tr = 1.01. Indication that polar species predominate in the transition state is supported by the observed order of reactivity. The usual rate dependence appeared to be followed by all of the monomers except vinyl acetate, which was retarded, severely in methyl oleate. Transfer in methyl oleate was about 5.8 times greater than that found in methyl stearate for these four monomers. The internal allylic double bond of methyl oleate had about the same reactivity in transfer as had the terminal unsaturation in N-allylstearamide at 90°C. Rough estimates were obtained of the monomer transfer constants for the long side-chain homologs of these four monomers from the respective monomer transfer constants and the experimental transfer constants, corrected for transfer to the labile groups of the solvent. It was concluded that the rate of polymerization would determine in large measure the degree of polymerization for the reactive 18-carbon homologs but that the molecular weight of poly(vinyl stearate) and (oleate) will be regulated primarily by transfer to monomer.     

Vinyl polymerization. 178. Copolymerizations of p-substituted phenyl vinyl sulfides

The copolymerizations of p-substituted phenyl vinyl sulfides (M₂) having OCH₃, CH₃, H, Cl, and Br substituents with styrene and methyl methacrylate (M₁) and their intercopolymerizations at 60°C. were studied. From the results of copolymerizations with styrene and methyl methacrylate, the monomer reactivity ratios and the Q₂e₂ values were determined. For example, the Q and e values for unsubstituted phenyl vinyl sulfide were 0.45 and ?1.26 in the copolymerization with methyl methacrylate. This result indicated the importance of the 3d orbital resonance between the sulfur atom and the adjacent carbon atom in the transition state of copolymerizations. The relative reactivities of these monomers toward the polymer radicals were found to be correlated with the Hammett σ constants of the substituents. In the intercopolymerizations of these monomers, it was also found that the relative reactivities followed the Hammett equation approximately.     

Cationic polymerization of vinyl monomers initiated by 10-methylphenothiazine cation radicals

A small quantity of 10-methylphenothiazine cation radical (MPT^.+), electrochemically prepared and stocked in acetonitrile solution, initiated cationic polymerizations of n-butyl, t-butyl, and 2-methoxyethyl vinyl ethers and p-methoxystyrene, while no initiation occurred for phenyl vinyl ether, styrene, methyl methacrylate, and phenyl glycidyl ether. ¹H-NMR studies of oligomers and low molecular weight compounds isolated from the reaction mixture for the polymerization of t-butyl vinyl ether in the presence of a small amount of D₂O indicated that electron transfer from the monomer to MPT^.+ was involved in the initiation step. ¹H- and ¹³C-NMR and MO calculation implied that monomers with higher electron densities on the vinyl groups and with lower ionization potentials were more susceptible to the initiation of MPT^.+. © 1994 John Wiley & Sons, Inc.