Separation of fluoroquinolones in acidic buffer by capillary electrophoresis with contactless conductivity detection

A method to determine five fluoroquinolones (FQs), namely, rufloxacin (RUF), ciprofloxacin (CIP), enrofloxacin (ENO), gatifloxacin (GAT) and moxifloxacin (MOX), in acidic buffer by capillary electrophoresis (CE)-capacitively coupled contactless conductivity detection (C⁴D) technique is presented. Separation was carried out in a fused-silica capillary (42 cm × 50 μm) using a buffer composed of 10 mM tartaric acid, 14 mM sodium acetate and 15% (v/v) methanol at pH 3.8. The RSDs of the migration times and peak areas were 0.65% and 12.3% (intraday), 1.28% and 8.8% (interday), respectively. CE-C⁴D in combination with liquid–liquid extraction (LLE) as clean-up and preconcentration procedure, allows detection of the FQs in fortified chicken muscle samples with detection limits of 6.8–11.7 ng/g. This method shows potential in rapid determination of FQs in samples with complex matrix.     

Rapid electrophoretic monitoring of the anaesthetic ketamine and its metabolite norketamine in rat blood using a contactless conductivity detector to study the pharmacokinetics

A method of capillary electrophoresis with contactless conductivity detection has been developed for non‐enantioselective monitoring the anaesthetic ketamine and its main metabolite norketamine. The separation is performed in a 15 μm capillary with an overall length of 31.5 cm and length to detector of 18 cm; inner surface of the capillary is covered with a commercial coating solution to reduce the electroosmotic flow. In an optimised background electrolyte with composition 2 M acetic acid + 1% v/v coating solution under application of a high voltage of 30 kV, the migration time is 97.1 s for ketamine and 95.8 s for norketamine, with an electrophoretic resolution of 1.2. The attained detection limit was 83 ng/mL (0.3 μmol/L) for ketamine and 75 ng/mL (0.3 μmol/L) for norketamine; the number of theoretic plates for separation of an equimolar model mixture with a concentration of 2 μg/mL was 683 500 plates/m for ketamine and 695 400 plates/m for norketamine. Laboratory preparation of rat blood plasma is based on mixing 10 μL of plasma with 30 μL of acidified acetonitrile, followed by centrifugation. A pharmacokinetic study demonstrated an exponential decrease in the plasma concentration of ketamine after intravenous application and much slower kinetics for intraperitoneal application.     

Monitoring of circulating amino acids in patients with pancreatic cancer and cancer cachexia using capillary electrophoresis and contactless conductivity detection

Branched chain amino acids (BCAAs), alanine and glutamine are determined in human plasma by capillary electrophoresis with contactless conductivity detection (CE/C⁴D). The baseline separation of five amino acids from other plasma components is achieved on the short capillary effective length of 18 cm in 3.2 mol/L acetic acid with addition of 13% v/v methanol as background electrolyte. Migration times range from 2.01 min for valine to 2.84 min for glutamine, and LODs for untreated plasma are in the interval 0.7–0.9 μmol/L. Sample treatment is based on the addition of acetonitrile to only 15 μL of plasma and supernatant is directly subjected to CE/C⁴D. Circulating amino acids are measured in patients with pancreatic cancer and cancer cachexia during oral glucose tolerance test. It is shown that patients with pancreatic cancer and cancer cachexia syndrome exhibit low basal circulating BCAAs and glutamine levels and loss of their insulin-dependent suppression.     

Low-cost and versatile analytical tool with purpose-made capillary electrophoresis coupled to contactless conductivity detection: Application to antibiotics quality control in Vietnam

In this study, the development of our purpose-made capacitively coupled contactless conductivity detection (C⁴D) for CE is reported. These systems have been employed as a simple, versatile, and cost-effective analytical tool. CE-C⁴D devices, whose principle is based on the control of the ion movements under an electrical field, can be constructed even with a modest financial budget and limited infrastructure. A featured application was developed for quality control of antimicrobial drugs using CE-C⁴D, with most recent work on determination of aminoglycoside and glycopeptide antibiotics being communicated. For aminoglycosides, the development of CE-C⁴D methods was adapted to two categories. The first one includes drugs (liquid or powder form) for intravenous injection, containing either amikacin, streptomycin, kanamycin A, or kanamycin B. The second one covers drugs for eye drops (liquid or ointment form), containing either neomycin, tobramycin, or polymyxin. The CE-C⁴D method development was also made for determination of some popular glycopeptide antibiotics in Vietnam, including vancomycin and teicoplanin. The best detection limit achieved using the developed CE-C⁴D methods was 0.5 mg/L. Good agreement between results from CE-C⁴D and the confirmation method (HPLC- Photometric Diode Array ) was achieved, with their result deviations less than 8% and 13% for aminoglycoside and glycopeptide antibiotics, respectively.     

Rapid determination of rifaximin in rat serum and urine by direct injection on to a shielded hydrophobic stationary phase by HPLC

A simple and rapid reversed‐phase HPLC method for determination of rifaximin in rat serum and urine was developed. Separation of rifaximin from biological matrix was achieved by direct injection of rat serum and urine onto a restricted‐access medium, Supelco LC‐Hisep, a shielded hydrophobic stationary phase, using acetonitrile:water:acetic acid (18:82:0.1 v/v/v) as a mobile phase. The linear range was 0.10–20 µg/mL (r² > 0.999, n = 6), intraday and interday variation was <6.10%. The limits of detection and quantification were 0.03 (signal‐to‐noise ratio >3) and 0.10 µg/mL (signal‐to‐noise ratio >10), respectively. The method was successfully applied to pharmacokinetic studies of rifaximin after an oral administration to rats. Copyright © 2008 John Wiley & Sons, Ltd.     

Mass Spectrometric and Contactless Conductivity Detection Approaches in the Determination of Muscle Relaxants by Capillary Electrophoresis

Novel and rapid capillary electrophoresis-coupled tandem mass spectrometry (CE-MS/MS) and capillary electrophoresis with capacitively coupled contactless conductivity detection (CE-C⁴D) methods have been developed for the separation and determination of three neuromuscular blocking agents: pancuronium, vecuronium, and rocuronium. In both cases, the separation was conducted in background electrolytes based on acidic acetate-ammonium buffers to avoid possible decomposition of the analytes that are known to be unstable in alkaline media. Baseline resolution of the analytes was achieved in the presence of modified γ-cyclodextrin by CE with C⁴D detection. The two detection techniques were compared with regard to analytical figures of merit including linear dynamic range, limit of detection, limit of quantification, precision, and accuracy. The calibration curves showed good linearity for both detection methods examined (characterized by r² ≥ 0.9908). The LODs of the CE-MS/MS and the CE-C⁴D methods differed at least by two orders of magnitude considering all analytes. The differences in precision and accuracy of these methods were evaluated and discussed. The assays of pancuronium, vecuronium, and rocuronium in commercial injection solutions by CE-MS/MS and CE-C⁴D were performed and the results compared.     

Sub-Minute Analysis of Lactate from a Single Blood Drop Using Capillary Electrophoresis with Contactless Conductivity Detection in Monitoring of Athlete Performance

A simple and fast method for the analysis of lactate from a single drop of blood was developed. The finger-prick whole blood sample (10 µL) was diluted (1:20) with a 7% (w/v) solution of [tris(hydroxymethyl)methylamino] propanesulfonic acid and applied to a blood plasma separation device. The device accommodates a membrane sandwich composed of an asymmetric polysulfone membrane and a supporting textile membrane that allows the collection of blood plasma into a narrow glass capillary in less than 20 s. Separated and simultaneously diluted blood plasma was directly injected into a capillary electrophoresis instrument with a contactless conductivity detector (CE-C⁴D) and analyzed in less than one minute. A separation electrolyte consisted of 10 mmol/L l-histidine, 15 mmol/L dl-glutamic acid, and 30 µmol/L cetyltrimethylammonium bromide. The whole procedure starting from the finger-prick sampling until the CE-C⁴D analysis was finished, took less than 5 min and was suitable for monitoring lactate increase in blood plasma during incremental cycling exercise. The observed lactate increase during the experiments measured by the developed CE-C⁴D method correlated well with the results from a hand-held lactate analyzer (R = 0.9882). The advantage of the developed CE method is the speed, significant savings per analysis, and the possibility to analyze other compounds from blood plasma.     

HPLC quantification of 5‐hydroxyeicosatetraenoic acid in human lung cancer tissues

A simple and cost‐effective HPLC method was established for quantification of 5‐hydroxyeicosatetraenoic acid (5‐HETE) in human lung cancer tissues. 5‐HETE from 27 patients' lung cancer tissues were extracted by solid‐phase extraction and analyzed on a Waters Symmetry C₁₈ column (4.6 × 250 mm, 5 µm) with a mobile phase consisting of methanol, 10 mm ammonium acetate, and 1 m acetic acid (70:30:0.1, v:v:v) at a flow rate of 1.0 mL/min. The UV detection wavelength was set at 240 nm. The calibration curve was linear within the concentration range from 10 to 1000 ng/mL (r² > 0.999, n = 7), the limit of detection was 1.0 ng/mL and the limit of quantitation was 10.0 ng/mL for a 100 µL injection. The relative error (%) for intra‐day accuracy was from 93.14 to 112.50% and the RSD (%) for intra‐day precision was from 0.21 to 2.60% over the concentration range 10–1000 ng/mL. By applying this method, amounts of 5‐HETE were quantitated in human lung cancer tissues from 27 human subjects. The established HPLC method was validated to be a simple, reliable and cost‐effective procedure that can be applied to conduct translational characterization of 5‐HETE in human lung cancer tissues. Copyright © 2009 John Wiley & Sons, Ltd.     

Analysis of bicarbonate,phosphate and other anions in saliva by capillary electrophoresis with capacitively coupled contactless conductivity detection in diagnostics of gastroesophageal reflux disease

Bicarbonate and phosphate constitute major salivary buffering components, and their importance consists in the neutralization of acidic gastric contents during reflux episodes. In this work, capillary electrophoresis with capacitively coupled contactless conductivity detector was applied for the analysis of bicarbonate, phosphate, and another inorganic (chloride, nitrite, nitrate, sulfate, thiocyanate) and organic anions (acetate, butyrate) to evaluate their levels in saliva. The background electrolytes of different composition and pH between 6.02–9.41 were assessed for the bicarbonate and phosphate determination by comparison of the real analyses of a model solution with the simulation by PeakMaster software. The optimized background electrolyte was composed of 10 mM 2-(N-morpholino)ethanesulfonic acid, 20 mM arginine, and 30 µM cetyltrimethylammonium bromide, pH 8.95. Using this BGE, the anion levels were compared in saliva from 20 patients suffering from gastroesophageal reflux disease (GERD) and saliva from 12 healthy subjects. Bicarbonate levels were significantly elevated in saliva from GERD patients suggesting the possible applicability of bicarbonate as a biomarker in non-invasive diagnostics of GERD by CE-C⁴D.     

HPLC‐UV method for quantifying etoposide in plasma and tumor interstitial fluid by microdialysis: application to pharmacokinetic studies

A simple and sensitive bioanalytical method was developed and validated for determination of etoposide in plasma and microdialysis samples of Walker‐256 tumor‐bearing rats. A microdialysis probe was implanted in the center of a subcutaneous tumor and Ringer's solution was used as perfusion medium. Chromatographic separation was conducted on a Shimadzu CLC‐C₈ column using a mobile phase consisting of water–acetonitrile (70:30; v/v) adjusted to pH 4.0 ± 0.1 with formic acid at a gradient flow rate of 1.0–0.6 mL/min, an injection volume of 30 μL and UV detection at 210 nm. Microdialysate samples were analyzed without processing and plasma samples (100 μL) were spiked with phenytoin as internal standard (IS) (1 µg/mL) followed by extraction with tert‐butyl methyl ether. The organic layer was evaporated and reconstituted with 100 μL of mobile phase before injection. The methods for plasma and microdialysate were linear in the ranges of 25–10,000 ng/mL and of 10–1500 ng/mL, respectively. All the validation parameters such as intra‐ and inter‐day precision and accuracy and stability were within the limits established by international guidelines. The present method was successfully applied in the investigation of etoposide pharmacokinetics in rat plasma and microdialysate tumor samples following a single 15 mg/kg intravenous dose. Copyright © 2014 John Wiley & Sons, Ltd.     

A rapid and simple HPLC method for the determination of curcumin in rat plasma: assay development,validation and application to a pharmacokinetic study of curcumin liposome

This paper describes a sensitive, specific and rapid high‐performance liquid chromatography (HPLC) method for the determination of curcumin in rat plasma. After a simple step of protein precipitation in 96‐well format using acetonitrile containing the internal standard (IS), emodin, plasma samples were analyzed by reverse‐phase HPLC. Curcumin and the IS emodin were separated on a Diamonsil C₁₈ analytical column (4.6 × 100 mm, 5 µm) using acetonitrile–5% acetic acid (75:25, v/v) as mobile phase at a flow rate of 1.0 mL/min. The method was sensitive with a lower limit of quantitation of 1 ng/mL, with good linearity (r² ≥ 0.999) over the linear range 1–500 ng/mL. All the validation data, such as accuracy and precision, were within the required limits. A run time of 3.0 min for each sample made high‐throughput bioanalysis possible. The assay method was successfully applied to the study of the pharmacokinetics of curcumin liposome in rats. Copyright © 2009 John Wiley & Sons, Ltd.     

Development of CE-C4D Method for Determination Tropane Alkaloids

A fast method for the determination of tropane alkaloids, using a portable CE instrument with a capacitively coupled contactless conductivity detector (CE-C⁴D) was developed and validated for determination of atropine and scopolamine in seeds from Solanaceae family plants. Separation was obtained within 5 min, using an optimized background electrolyte consisting of 0.5 M acetic acid with 0.25% (w/v) β-CD. The limit of detection and quantification was 0.5 µg/mL and 1.5 µg/mL, respectively, for both atropine and scopolamine. The developed method was validated with the following parameters—precision (CV): 1.07–2.08%, accuracy of the assay (recovery, RE): 101.0–102.7% and matrix effect (ME): 92.99–94.23%. Moreover, the optimized CE-C⁴D method was applied to the analysis of plant extracts and pharmaceuticals, proving its applicability and accuracy.     

Separation and determination of alkyl sulfate surfactants in wastewater by capillary electrophoresis coupled with contactless conductivity detection after preconcentration by simultaneous adsorption using alumina beads

The aim of the present study is to determine four anionic alkyl sulfate (AS) surfactants with different alkyl chains, namely, C8, C10, C12, and C14, in wastewater by CE with capacitively coupled contactless conductivity detection (CE-C⁴D). The conditions effective for the separation of the four AS surfactants were systematically optimized and found to be in a Tris-His (50 mM/20 mM) BGE solution at a pH of 8.95, using a separation voltage of +15 kV, hydrodynamic injection by siphoning using a 20 cm injection height and an injection time of 20 s. The LODs for C8, C10, C12, and C14 were 2.58, 2.30, 2.08, and 3.16 mg/L, respectively. The conditions used to achieve the simultaneous adsorption and preconcentration of the AS surfactants using Al₂O₃ beads were pH of 3 and 0.1 mM NaCl. The adsorption efficiencies were found to be 45.6, 50.8, 81.7, and 99.9%, while the desorption efficiencies reached 66.1, 70.4, 83.9, and 100.0% for C8, C10, C12, and C14, respectively. The concentrations of the AS surfactants in wastewater samples were quantified by CE-C⁴D after preconcentration by simultaneous adsorption using Al₂O₃ beads. The results obtained from the proposed method were consistent with those obtained by HPLC-MS/MS, with a deviation of less than 15%. Our results indicate that the CE-C⁴D performed after preconcentration by an adsorption technique using Al₂O₃ beads is a new, inexpensive, and suitable method for quantifying AS surfactants in wastewater samples.     

Analysis of amino acids in cell culture supernatant using capillary electrophoresis with contactless conductivity detection

CE-C⁴D methods for the analysis of amino acids (AAs) are presented. Combining the results from two methods with acetic acid and cyclodextrin-based BGEs, 20 proteinogenic AAs could be analyzed using CE. CE-C⁴D was also, for the first time, applied to analyze free AAs in samples of mammalian cell culture supernatant. After dilution as only sample preparation, combining the results of the two CE methods allowed monitoring the concentration changes of 17 AAs in samples taken during the cultivation of CHO cells.     

A voltage trade study for the design of capillary electrophoresis instruments for spaceflight

Capillary electrophoresis (CE) systems have undergone extensive development for spaceflight applications. A flight-compatible high voltage power supply and the necessary voltage isolation for other energized components can be large contributors to both the volume and mass of a CE system, especially if typical high voltage levels of 25–30 kV are used. Here, we took advantage of our custom CE hardware to perform a trade study for simultaneous optimization of capillary length, high voltage level, and separation time, without sacrificing method performance. A capillary electrophoresis with capacitively coupled contactless conductivity detection (CE-C⁴D) method recently developed by our group to target inorganic cations and amino acids relevant to astrobiology was used as a test case. The results indicate that a 50 cm long capillary with 15 kV applied voltage (half of that used in the original method) can be used to achieve measurement goals while minimizing instrument size.     

Liquid chromatographic determination of cis-platin as platinum(II) in pharmaceutical preparation, serum and urine samples of cancer patients

Spectrophotometric and high performance liquid chromatographic (HPLC) methods have been developed for the determination of cis-platin and carboplatin based on the pre-column derivatization of platinum(II) with 2-acetylpyridine-4-phenyl-3-thiosemicarbazone. The complex was extracted in chloroform with molar absorptivity of 2.2 × 10⁴ L mol⁻¹ cm⁻¹ at 380 nm. The complex eluted from a Phenomenex C-18 (150 mm × 4.6 mm i.d.) column with methanol:water:acetonitrile:tetrabutyl ammonium bromide (1 mM) (44:30:25:1, v/v/v/v) with a flow rate of 1 ml/min and UV detection at 260 nm. Ruthenium(IV) and selenium(IV) also separated completely. The linear calibration curve was with 0.5-12.5 μg/ml and detection limit of 10 ng/ml platinum(II).The analysis of cis-platin and carboplatin injections by spectrophotometric and HPLC methods indicated relative standard deviation (R.S.D.) of 0.66-2.1%. The method was used for the determinations of cis-platin in serum and urine of cancer patients after chemotherapy and platinum contents were found 148-444 and 50-90 ng/ml with R.S.D. of 0.3-3.0 and 0.6-2.4% for the serum and urine, respectively. The recovery of platinum(II) from serum was 97% with R.S.D. 2.2%.     

Chiral stability-indicating HPLC method for analysis of arotinolol in pharmaceutical formulation and human plasma

An enantioselective stability-indicating high performance liquid chromatographic method was developed for the analysis of arotinolol in standard solution. The degradation behaviour of arotinolol was investigated under different stress conditions recommended by International Conference on Harmonization (ICH). Resolution of the drug and complete separation from its degradation products were successfully achieved on a Chirobiotic V column, using UV detector set at 315 nm, polar organic mobile phase (POM) consisting of methanol:glacial acetic acid:triethylamine, 100:0.02:0.03, (v/v/v), and a flow rate of 1 ml/min. The drug was subjected to oxidation, hydrolysis, photolysis, and heat to apply stress conditions. The drug was found to degrade in alkaline, acidic, oxidative conditions and when exposed to heat. The drug was stable to sunlight. The method reported here has also been successfully applied to pharmaceutical formulation and to human plasma that spiked with stock solutions of arotinolol enantiomers.Arotinolol enaniomers were recovered from plasma by using liquid–liquid extraction procedure with ethyl ether. The method was highly specific, where degradation products and coformulated compounds did not interfere, and was sensitive with good precision and accuracy and was linear over the range of 50–400 ng/ml (R² > 0.9981) with a detection limit of 20 ng/ml for each enantiomer. The mean extraction efficiency for arotinolol was in the ranges 96–104% for each enantiomer. The mean relative standard deviation (RSD) of the results of within-day precision and accuracy of the drug were ?7.1%. There was no significant difference between inter- and intra-day studies for each enantiomers which confirmed the reproducibility of the assay. The overall recoveries of arotinolol enantiomers from pharmaceutical formulations were in the ranges 97.6–101.8%.     

Determination of chlorine species by capillary electrophoresis – mass spectrometry

The applicability of CZE with mass spectrometric detection for the determination of four chlorine species, namely chloride and three stable chlorine oxyanions, was studied. The main aspects of the proper selection of BGE and sheath liquid for the CE‐MS determinations of anions with high mobility were demonstrated, pointing out the importance of pH and the mobility of the anion in the BGE. The possibility of using uncoated fused silica capillary and common electrolytes for the separation was shown and the advantage of using extra pressure at the inlet capillary end was also presented. The linear range was found to be 1–100 µg/mL for ClO₃^? and ClO₄^?, 5–500 µg/mL for ClO₂^?, and 25–500 µg/mL for Cl^?, but the sensitivity can be greatly improved if larger sample volume is injected and electrostacking effect is utilized. The LOD for ClO₃^? in drinking water was 6 ng/mL, when very large sample volume was injected (10 000 mbar·s was applied).     

Determination of Matrine and Oxymatrine in Sophora Flavescens by Nonaqueous Capillary Electrophoresis-Electrospray Ionization-Ion Trap-Mass Spectrometry

A simple, rapid, and sensitive nonaqueous capillary electrophoresis-electrospray ionization-ion trap-mass spectrometry (NACE-ESI-IT-MS) method was developed for determination of matrine and oxymatrine in Sophora Flavescens and medicinal preparations. The conditions for NACE separation and MS detection were systematically optimized. The optimum NACE buffer contained 30 mM ammonium acetate, 1% acetic acid, and 15% acetonitrile in methanol and the applied voltage on separation capillary was set at 25 kV. Berberine was selected as internal standard. In order to generate a stable electrospray, a sheath liquid (isopropanol/H₂O, 2/1, v/v) was used, which could also boost the flow through the ESI needle. The matrine and oxymatrine solutions were introduced into MS detection by a syringe pump for collecting the MSⁿ spectra to investigate the main fragment ions and its possible cleavage pathways. Both matrine and oxymatrine showed good linearity in the concentration ranges from 0.5 to 400 µg/mL, with linear correlation coefficient R > 0.99 and the limit of detections were 37.5 ng/mL for matrine and 50.0 ng/mL for oxymatrine, respectively. The recoveries at different content of Sophora Flavescens were 98.3%–102.9% for MT and 95.3%–100.6% for OMT, which indicates the reliability of this method.     

Analysis of meloxicam by high-performance liquid chromatography with cloud-point extraction

A simple cloud-point extraction method for the determination of meloxicam in human serum was developed. Meloxicam was extracted from serum sample after adding 1 mL of 3% (v/v) Triton X-114 aqueous solution in the presence of 1M HCl and 60 mg NaCl. The meloxicam, present in the surfactant-rich phase, was enriched again with acetonitrile. Tenoxicam was used as the external standard. The separation was achieved on a C18 analytical column with a mobile phase consisting of aqueous acetic acid (1%, v/v) and acetonitrile (54:46, v/v). UV detection was performed at 360 nm. The response was linear over the range 45–2000 ng mL⁻¹ in human serum, and intra- and interday precisions of less than 15.0% were obtained. The relative error was within ±3.0%. The recoveries of meloxicam were larger than 92.0%. The method was compared with liquid–liquid extraction. The results showed that the new method has a considerable LOQ and higher recoveries but poorer precision than liquid–liquid extraction, which exhibited poor recoveries of less than 86.0%, precisions of less than 5.0% and relative errors of less than 7.0%. The method was used for the determination of meloxicam in healthy human volunteers.