A fused silica micro-electrospray tip with an electrically floating metal wire insert to achieve more stable electrospray ionization

A new electrospray tip with a wire insert was tested and compared with the conventional bare fused silica capillary tip. The new tip combined the approach of conventional fused silica spray tips with those containing metal wires. Here, we used a floating wire so that the tips could be prepared and replaced more easily. With the conventional tip, the electrospray process became unstable and the spray current fluctuated significantly in the presence of an air bubble. When the wire-inserted tip was used under the same conditions, much less signal deterioration occurred. The superior performance of this tip over the conventional tip was attributable to its enhanced electric conduction. The new tip has great potential for improving signal stability in LC mass spectrometry.     

A Combined Desorption Ionization by Charge Exchange (DICE) and Desorption Electrospray Ionization (DESI) Source for Mass Spectrometry

A source that couples the desorption ionization by charge exchange (DICE) and desorption electrospray ionization (DESI) techniques together was demonstrated to broaden the range of compounds that can be analyzed in a single mass spectrometric experiment under ambient conditions. A tee union was used to mix the spray reagents into a partially immiscible blend before this mixture was passed through a conventional electrospray (ES) probe capillary. Using this technique, compounds that are ionized more efficiently by the DICE method and those that are ionized better with the DESI procedure could be analyzed simultaneously. For example, hydroquinone, which is not detected when subjected to DESI-MS in the positive-ion generation mode, or the sodium adduct of guaifenesin, which is not detected when examined by DICE-MS, could both be detected in one experiment when the two techniques were combined. The combined technique was able to generate the molecular ion, proton and metal adduct from the same compound. When coupled to a tandem mass spectrometer, the combined source enabled the generation of product ion spectra from the molecular ion and the [M + H]⁺ or [M + metal]⁺ ions of the same compound without the need to physically change the source from DICE to DESI. The ability to record CID spectra of both the molecular ion and adduct ions in a single mass spectrometric experiment adds a new dimension to the array of mass spectrometric methods available for structural studies.     

Characteristics of probe electrospray generated from a solid needle

Probe electrospray ionization (PESI) has recently been developed, in which the electrospray was generated from a solid needle instead of by using a capillary. In this paper, the characteristics of probe electrospray ionization were studied based on the measurement of spray current, optical microscopy, and PESI mass spectrometry. In the experiment, the solid needle was moved up and down a vertical axis, and a small amount of sample was repeatedly loaded to the needle when the tip of the needle touched the surface of the liquid sample at the lowest position. After the application of high voltage, a liquid droplet was formed on the tip of the solid needle probe, with its size was determined by the size of the needle tip. The liquid flow rate to the tip, as indicated by the spray current, depends on the voltage applied to the needle as well as the loaded liquid amount. Stable electrospray can be maintained until the total consumption of liquid sample. The kilohertz current pulsation takes place in the case of overloading the sample to the needle. The influences of the applied voltage and the liquid flow rate on the PESI mass spectra were also examined.     

Generation of electrospray from a solution predeposited on optical fibers coiled with a platinum wire

This study examines the feasibility of generating electrospray directly from the tip of two optical fibers bound together with Teflon tape. This approach does not require a capillary and syringe pump. The electrospray source is simply constructed by coiling the two optical fibers with a platinum (Pt) wire. The optical fibers extend beyond the Pt coil for approximately 1 cm. The sample solution is predeposited on the Pt coil by a micropipette. As the high voltage required for electrospray is applied to the coil, the sample solution moves along the grooves between the two optical fibers. A stable electrospray is subsequently generated at the tip of the fibers. The mass spectra of insulin, lysozyme, and ubiquitin are exactly the same as those obtained by conventional electrospray using a capillary and syringe pump. Rapid determination of the active ingredient in a tablet by this technique is demonstrated.     

Current measurements within the electrospray emitter

A movable disc-like wire probe electrode placed inside the electrospray (ES) capillary was used to measure currents flowing within the ES device for the first time. Currents were measured between the wire probe and the ES capillary. Current maps revealing measured current versus wire probe position were generated for a variety of solution conditions in the positive and negative ion modes and are compared to potential maps. The electrospray device was found to subsist on highly stable total currents; this current regulator aspect of the ES device showed remarkable resiliency regardless of the proportion of current produced at the wire probe electrode versus the ES capillary. However, kinks observed in the current and potential maps are attributed to adsorbed air participating in electrochemical reactions, and turbulence in solution flow in the region of the Taylor cone. From differential electrospray emitter potential (DEEP) maps, current maps, and cyclic voltammetry experiments performed at different wire probe locations, evidence is provided for separate regimes of current flow in the bulk solution and in the thin "skin" of highly conductive electrolyte constituting the outer surface (air interface) of the Taylor cone. Current maps reveal that current is drawn more evenly along the length of the ES capillary when solutions are highly conductive, in agreement with previous results for DEEP maps. In less conductive solutions, the area close to the capillary exit contributes more heavily to current production. Evidence that contaminant participation in electrochemical processes occurring within the electrospray device can be largely responsible for production of the excess charge in ES droplets is also provided. These investigations complement previous DEEP mapping studies to further elucidate the details of the electrochemical processes occurring within the electrospray device.     

A new mass spectrometry electrospray tip obtained via precise mechanical micromachining

A new electrospray tip incorporating a beveled edge has been designed for use in plastic electrophoresis chip/electrospray mass spectrometry. Theoretical hydrodynamic analysis has been conducted to model the analytical sensitivity of the spray tip shape. A larger sample wall, that provides increased hydraulic pressure, is recommended in order to preserve the fluid stability at the tip outlet. A polymer with better hydrophobic characteristics than glass was used for the spray tip in order to restrict moisture accumulation at the spray tip outlet. Experimental results demonstrate that the analytical sensitivity of the proposed scheme is better than that obtained using the flat-head tip. Although a tapered capillary tip is commonly used in electrophoresis chip/electrospray mass spectrometry, the proposed tip offers a similar sensitivity while being more rugged and durable than the conventional tapered capillary tip. The cost of our design is also much lower than conventional spray tips.     

Ultrasonication-assisted spray ionization mass spectrometry for the analysis of biomolecules in solution

In this paper, we describe a novel technique—ultrasonication-assisted spray ionization (UASI)—for the generation of singly charged and multiply charged gas-phase ions of biomolecules (e.g., amino acids, peptides, and proteins) from solution; this method employs a low-frequency ultrasonicator (ca. 40 kHz) in place of the high electric field required for electrospray ionization. When a capillary inlet is immersed into a sample solution within a vial subjected to ultrasonication, the solution is continually directed to the capillary outlet as a result of ultrasonication-assisted capillary action; an ultrasonic spray of the sample solution is emitted at the outlet of the tapered capillary, leading to the ready generation of gas-phase ions. Using an ion trap mass spectrometer, we found that singly charged amino acid and multiply charged peptides/proteins ions were generated through this single-step operation, which is both straightforward and extremely simple to perform. The setup is uncomplicated: only a low-frequency ultrasonicator and a tapered capillary are required to perform UASI. The mass spectra of the multiply charged peptides and proteins obtained from sample solutions subjected to UASI resemble those observed in ESI mass spectra.     

The potential and challenges of elemental speciation by capillary electrophoresis-inductively coupled plasma mass spectrometry and electrospray or ion spray mass spectrometry

Capillary electrophoresis-inductively coupled plasma mass spectrometry (CE-ICP-MS) and electrospray (ES) or ion spray (IS) mass spectrometry (MS) are recently introduced techniques for elemental speciation. Both techniques have the potential for rapid elemental speciation with low detection limits. Examples of the use of CE-ICP-MS for elemental speciation of positive, neutral and negative species are discussed. Issues in interfacing CE and ICP-MS are considered briefly. The potential advantages and disadvantages of laminar flow in CE-ICP-MS are examined. Potential difficulties in CE-ICP-MS including loss of sample, chemical matrix effects and changes in speciation during separation are discussed. The interpretation of ES or IS-MS spectra and analysis of complex mixtures are considered. Calibration and chemical matrix effects are assessed. Potential pitfalls of interpreting bare metal ion spectra as elemental analysis are discussed. The need for fundamental understanding of the processes that control ES and IS-MS signals is examined. High conductivity samples currently present difficulties for CE-ICP-MS or ES and IS-MS.     

Minimizing analyte electrolysis in an electrospray emitter

The electrospray (ES) ion source is a controlled-current electrolytic flow cell. Electrolytic reactions in the ES emitter capillary are continually ongoing to sustain the production of charged droplets and ultimately gas-phase ions from this device. Under certain circumstances, the analytes under study may be directly involved in these electrolytic processes. It is demonstrated that a simple means to minimize analyte electrolysis is to exchange the normal metal emitter capillary of commercial ES sources with one made of fused silica. This change is shown to provide an ES mass spectrometric system of similar performance in terms of gas-phase ion signal generated for non-electroactive analytes and also assures minimal oxidation of electroactive analytes even at low (2.0 microl x min(-1)) solution flow-rates and high (millimolar) solution electrolyte concentrations.     

Denaturation of lysozyme and myoglobin in laser spray

In laser spray, the tip of an electrospray capillary is irradiated with a continuous CO(2) laser beam. Here, we report results from a modified laser spray method that employs a relatively low laser irradiance level. With a laser power of approximately 2 W and a focal spot size ( approximately 0.3 mm), which covered the entire front surface of the electrospray capillary, the irradiance was approximately 3 x 10(3) W/cm(2). This resulted in a quiescent and smooth vaporization of aqueous solutions. This "evaporation-mode" laser spray method yielded the best results so far obtained in our laboratory with laser-irradiated electrospray, producing higher and more stable signals. The method was applied to the analysis of aqueous solutions of lysozyme and myoglobin. Mass spectra were obtained as a function of laser power from 0 W (electrospray) to approximately 2 W. The spray generated at the tip of the stainless steel capillary was observed with a CCD camera. With increase of laser power, the droplets in the spray became finer and the Taylor cone became progressively smaller. The strongest ion signals were recorded when the sample solution protruded only slightly from the tip of the capillary. A broadening of the lysozyme charge-state distribution, attributable to protein unfolding, was observed with a laser power of 2 W. No denaturation of myoglobin took place up to a laser power of 1.6 W. However, a sudden onset of denaturation was observed at 1.8 W as a broadening of the myoglobin charge distribution and the appearance of apo-myoglobin peaks. These findings demonstrate that laser spray is capable of dissociating the noncovalent complexes selectively without breaking covalent bonds.     

Direct analysis of oligosaccharides and alpha hydroxy acids in fruits using electrosonic spray ionization mass spectrometry

Electrosonic spray ionization (ESSI) is a derivative technique of electrospray ionization (ESI) for mass spectrometry (MS) in which droplets are charged in the course of sonic spray. In this study, we applied ESSI MS to direct analysis of oligosaccharides and alpha hydroxy acids (AHAs) in fruits. The components were extracted from fruit fleshes by a feasible method prior to ESSI MS analysis, but the fruit juices were analyzed without further pretreatment. The results demonstrate that mainly alkali metal adducts of oligosaccharides are favorably produced in positive ion mode, while deprotonated AHAs and oligosaccharides are produced in negative ion mode. Compared with mass spectra obtained using electrospray droplet impact/secondary ion mass spectrometry (EDI/SIMS), mass spectra using ESSI make the identification of oligosaccharides more straightforward in positive ion mode than in negative ion mode.     

Novel microfabricated device for electrokinetically induced pressure flow and electrospray ionization mass spectrometry

A novel microchip device for electrospray ionization has been fabricated and interfaced to a time-of-flight mass spectrometer. Fluid is electrokinetically transported through the chip to a fine fused-silica capillary inserted directly into a channel at the edge of the device. Electrospray is established at the tip of the capillary, which assures a stable, efficient spray. The electric potential necessary for electrospray generation and the voltage drop for electroosmotic pumping are supplied through an electrically permeable glass membrane contacting the fluidic channel holding the capillary. The membrane is fabricated on the microchip using standard photolithographic and wet chemical etching techniques. Performance relative to other microchip electrospray sources has been evaluated and the device tested for potential use as a platform for on-line electrophoretic detection. Sensitivity was found to be approximately three orders of magnitude better than spraying from the flat edge of the chip. The effect of the capillary on electroosmotic flow was examined both experimentally and theoretically.     

Formation of iron complexes from trifluoroacetic acid based liquid chromatography mobile phases as interference ions in liquid chromatography/electrospray ionization mass spectrometric analysis

Two unexpected singly charged ions at m/z 1103 and 944 have been observed in mass spectra obtained from electrospray ionization mass spectrometric analysis of liquid chromatography effluents with mobile phases containing trifluoroacetic acid (TFA) that severely interfered with sample analysis. Accurate mass measurement and tandem mass spectrometry studies revealed that these two ions are composed of three components; clusters of trifluoroacetic acid, clusters of mass 159 and iron. Formation of these ions is inhibited by removing TFA from the mobile phases and using formic acid in its place, replacing the stainless steel union with a titanium union or by adding a small blank fused-silica capillary column between the chromatography column and the electrospray tip via a stainless steel union without any adverse effects to chromatographic separation, peak broadening or peptide identifications.     

An electrospray-ionization mass spectrometer with new features

The construction and performance of an electrospray-ionization mass spectrometer with new features are described. The mass spectrometer consists of a newly designed electrospray ion-source that is plugged directly into a modified commercial quadrupole mass spectrometer with the ions entering the mass analyzer through a long metal capillary tube and three stages of differential pumping. The present ion source differs from previous designs in the combination of techniques employed in the transportation and desolvation of solvated biomolecule ions, prior to mass analysis. Transport of ionized entities between atmospheric pressure and vacuum is carried out through a 203 mm long stainless steel capillary tube with a 0.5 mm bore. Desolvation is effected by the use of controlled heat transfer through the long capillary tube and collisional activation in a region of reduced pressure between the capillary tube exit and the skimmer. Desolvation with this system is convenient and effective and does not involve the strong countercurrent flows of gases that have been used by all previous workers. The effects on the spectra of peptides of capillary tube temperature and desolvation collision energy are investigated. Electrospray-ionization mass spectrometric results are described for thirteen proteins with molecular masses ranging from 5000 to 77,000 Da. The performance of the present instrument, with respect to mass accuracy and sensitivity, is comparable with previously reported systems. The effect of protein concentration in solution on the electrospray mass spectrometric response and charge-state distribution is discussed.     

Laser spray: electric field-assisted matrix-assisted laser desorption/ionization

A new liquid chromatography/mass spectrometry interface, the laser spray, has been developed. Explosive vaporization and mist formation occur when an aqueous solution effusing out from the tip of the stainless-steel capillary is irradiated from the opposite side of the capillary by a 10.6 microm infrared laser. Weak ion signals could be detected when the plume was sampled through the ion sampling orifice. When a high voltage (3-4 kV) was applied to the stainless-steel capillary, strong ion signals appeared. The ion abundances were found to be orders of magnitude greater than those obtained by conventional electrospray ionization in the case of aqueous solutions. The present method is regarded as an electric-field assisted form of matrix-assisted laser desorption/ionization in which the liquid chromatographic solvent (water, etc.) acts as a liquid matrix. Laser spray ionization is expected to become a versatile method for biological mass spectrometry because this method is compatible with the natural solvent, water.     

Negative ion formation in electrospray mass spectrometry

Analytical and Chemical Sciences, Research Triangle Institute, Research Triangle Park, North Carolina, USA Negative ion electrospray (ES) operating on a single quadrupole mass spectrometer for the detection of low-molecular-weight molecules is discussed. The ES interface was operated at a positive cylindrical electrode potential to produce negative ions, and the results obtained were compared to the positive ion mode. As in the case of operation in the more common positive mode, negative ions with varying degrees of solvation and structurally relevant fragments can be obtained from a variety of solute species, including β-lactam antibiotics, aminoglycosides, aminocyclitols, tetracyclines, sulfonamides, nucleotides, peptides, and explosives. No fragmentation of parent species, except those from some labile explosives, was provided because low potential differences are applied between the capillary and the first skimmer, and electrical discharge is avoided in the gas phase. An increase in the capillary voltage resulted in collision-induced decomposition to produce structurally relevant fragment ions in both operation modes. An evaluation of representative chromatographic solvents indicated that 2-propanol added with oxygen in the ES bath gas is best suited to suppress electrical (corona) discharge phenomena in negative ion operation, whereas it aids in solution nebulization, desolvation, and transfer of ions in solution to the gas phase. For positive ion mode, no such precaution was necessary. Conditions that promote the formation of ions in solution usually improve ES response. Therefore, an increase in the solvent pH can increase the sensitivity in negative ion ES ionization. Negative ion ES offers the advantage of providing complementary structural information to help in the characterization of an unknown compound or to confirm a certain tentatively proposed structure. Nucleotides and explosives were best characterized in negative ion mode owing to the ease with which they form anions in solution, and they could be detected down to the l-pg /gML level.     

Influence of droplet size, capillary-cone distance and selected instrumental parameters for the analysis of noncovalent protein-ligand complexes by nano-electrospray ionization mass spectrometry

It has been suggested in the literature that nano-electrospray ionization (nano-ESI) mass spectrometry better reflects the equilibrium between complex and free protein in solution than pneumatically assisted electrospray ionization (ESI) in noncovalent interaction studies. However, no systematic studies of the effects of ionization conditions have been performed to support this statement. In the present work, different instrumental and sample-derived parameters affecting the stability of noncovalent complexes during analysis by nano-ESI were investigated. In general, increased values of parameters such as drying gas flow-rate, ion-source temperature, capillary tip voltage and buffer concentration lead to a dissociation of ribonuclease A (RNAse)-cytidine 2'-monophosphate (CMP) and cytidine 5'-triphosphate (CTP) complexes. The size of the electrosprayed droplets was shown to be an important issue. Increasing the capillary to cone distance yielded an increased complex to free protein ratio when a hydrophilic ligand was present and the reverse effect was obtained with a hydrophobic ligand. Important in this regard is the degree of sampling of ions originating from late-generation residue droplets, that is, ions present in the droplet bulk. Sampling of these ions increases with longer capillary-cone distance (flight time). Furthermore, when the sample flow-rate was increased by increasing the capillary internal tip i.d. from 4 to 30 microm, a decreased complex to free protein ratio for the RNAse-CTP system was observed. This behavior was consistent with the change in surface to volume ratio for flow-rates between 2 and 100 nl min(-1). Finally, polarity switching between positive and negative ion modes gave a higher complex to free protein ratio when the ligand and the protein had the same polarity.     

A novel nanoflow interface for atmospheric pressure ionization mass spectrometry

A novel spray-ionization technique for nanoflow liquid chromatography/mass spectrometry (nLC/MS) has been developed by modifying the sonic spray ionization (SSI) technique. A solution from a tapered fused-silica capillary is sprayed by a gas flow coaxial to the capillary, and ions produced are analyzed with an ion-trap mass spectrometer. The ion intensity is shown to have a steep threshold at a low gas velocity and to be much less dependent on the gas velocity than that of conventional SSI, in which the ion intensity is strongly dependent on the gas velocity and reaches its maximum at sonic velocity. Thus, we conclude that the concentration of charge in the solution at the tapered capillary tip with an inner diameter of 15 microm is almost at saturation so that charged droplets are produced from the solution by electrical force, rather than by sheer stress due to the gas flow. The ions are readily produced from these charged droplets. Preliminary results are compared with results obtained with a miniaturized electrospray unit.     

Effect of substituents and protonation on the mechanism of 1,3-dipolar retro-cycloaddition reaction of pyrrolidino[60]- and [70]fullerenes

The mass spectra of new substituted pyrrolidino[60]- and [70]fullerenes have been obtained using electrospray ionization conditions in the positive and negative mode of detection with two different mass spectrometers, a quadrupole ion trap and a Fourier transform ion cyclotron resonance. Radical anions M(●-) and deprotonated molecules [M-H](-) are formed under negative electrospray ionization mass spectrometry conditions, and the collision-induced dissociations of both ionic species have been studied. Either negative odd-electron ions or negative even-electron ions undergo a retro-cycloaddition process forming the corresponding fullerene product ions C(60)(●-) and C(70)(●-). The generation of fullerene radical anions from deprotonated molecules is a new exception of the "even-electron rule." In contrast, the protonated molecules [M + H](+) obtained from the positive mode of detection do not undergo this cycloreversion reaction, and the MS(n) experiment reveals a variety of eliminations of neutral molecules involving different hydrogen shifts and multiple bond cleavages that lead eventually to substituted methanofullerene fragment ions. The observed fragmentations can be correlated with the electronic character of the substituents attached to the heterocyclic moiety. The results obtained from the thermal reactions of these compounds, carried out under different pH conditions, correlate well with those obtained in gas phase. The different behaviors between protonated and unprotonated molecules and ions can be explained assuming that the retro-cycloaddition reaction takes place only when the nitrogen atom of the pyrrolidine ring (the basic center of the molecule) is unprotonated both in gas and condensed phase. The protonation of the NH group inhibits the cycloreversion process, and therefore different fragmentations take place. The detailed mechanisms of the formation and evolution of the intermediate fragments are described.     

Electrospray ionization tandem mass spectrometric study of salt cluster ions. Part 1--investigations of alkali metal chloride and sodium salt cluster ions

Salt cluster ions of alkali metal chlorides ACl (A = Li(+), Na(+), K(+), Rb(+) and Cs(+)) and sodium salts NaB (B = I(-), HCOO(-), CH(3)COO(-), NO(2)(-), and NO(3)(-)), formed by electrospray ionization, were studied systematically by mass spectrometry. The influences on the total positive ion and negative ion currents of variation of solvent, solution concentration, desolvation temperature, solution flow-rate, capillary voltage and cone voltage were investigated. Only cone voltage was found to influence dramatically the distribution of salt cluster ions in the mass spectra observed. Under conditions of normal cone voltage of approximately 70 V, cluster ions having magic numbers of molecules are detected with high relative signal intensity. Under conditions of low cone voltage of approximately 10 V, the distribution of cluster ions detected is characterized by a relatively low average mass/charge ratio due to the presence of multiply charged cluster ions; in addition, there is a marked reduction in cluster ions having a magic number of molecules. Product ion mass spectra obtained by tandem mass spectrometry of cluster ions are characterized by a base peak having a magic number of molecules that is less than and closest to the number of molecules in the precursor ion. Structures have been proposed for some dications and some quadruply charged ions. At pH 3 and 11, the mass spectra of NaCl clusters show the presence of mixed clusters of NaCl with HCl and NaOH, respectively. The effects of ionic radius on 20 distributions of cluster ions for 10 salts were investigated; however, the fine structure of these effects is not readily discerned.