Dynamic pH barrage junction focusing of amino acids,peptides, and digested monoclonal antibodies in capillary electrophoresis–mass spectrometry

Dynamic pH barrage junction focusing in CE enables effective signal enhancement, quantitative capture efficiencies, and straightforward optimization. The method is a technical variant of dynamic pH junction focusing. CE separation with dynamic pH barrage junction focusing is compatible with both optical and mass spectrometric detection. We developed a CE–MS/MS method using hydrophilic polyethyleneimine-coated capillaries and validated it for the qualitative analysis of amino acids, peptides, and tryptic peptides of digested monoclonal antibodies. The S/N of extracted ion electropherograms of zwitterionic analytes were enhanced by approximately two orders of magnitude with a tradeoff of a shortened separation window. Online focusing improved the MS signal intensity of a diluted antibody digest, enabling more precursor ions to be analyzed with subsequent tandem mass spectrometric identification. It also broadened the concentration range of protein digest samples for which adequate sequence coverage data can be obtained. With only 0.9 ng of digested infliximab sample loaded into the capillary, 76% and 100% sequence coverage was realized for antibody heavy and light chains, respectively, after online focusing. Full coverage was achieved with 9 ng of injected digest.     

Trimethylsilyldiazomethane derivatization coupled with solid-phase extraction for the determination of alendronate in human plasma by LC-MS/MS

Alendronate is an important representative of bisphosphonates, strongly polar compounds that lack chromophores. With rare exceptions, derivatization of the analytes is necessary for bioanalysis. In this study, a rapid liquid chromatography–tandem mass spectrometry method employing pre-column derivatization was developed and validated for the determination of alendronate concentrations in human plasma. The procedure was based on derivatization with trimethylsilyldiazomethane during solid-phase extraction on a weak anion-exchange solid-phase cartridge, which integrated sample purification and derivatization into one step. The alendronate derivative was eluted with methanol. Chromatographic separation was performed on a Capcell PAK-C18 column. The total run time was 6.5 min. The calibration curve was linear in the range 1.00–1,000 ng/mL using d6-alendronate as the internal standard. The lower limit of quantification was 1.00 ng/mL. The intra- and inter-assay precision (in RSD) calculated from quality control samples was less than 15%, and the accuracy was between 98.1% and 100.2%. The validated method was successfully applied to characterize the pharmacokinetic profiles of alendronate following the intravenous infusion of 5 or 10 mg alendronate sodium to healthy volunteers.     

Quantification of imatinib and related compounds using capillary electrophoresis-tandem mass spectrometry with field-amplified sample stacking

A quantification method for imatinib (IM), its major metabolite N-desmethyl imatinib (NDI), and a degradation by-product was developed using CE–MS combined with an online concentration technique. The use of multiple reaction monitoring (MRM)–MS/MS further improved the sensitivity of this technology. Liquid–liquid extraction (LLE) using tertiary butyl methyl ether yielded high recovery and reproducibility for the pretreatment of serum samples. The recovery rate exceeded 83% for all three analytes, and was 90% for IM. To improve quantification results, a conductivity-induced online analyte concentration technique, field-amplified sample stacking (FASS), was used. The S/N ratios were improved at least 10-fold when compared with conventional capillary zone electrophoresis. The detection limits were 0.2 ng/mL for IM, 0.4 ng/mL for NDI, and 4 ng/mL for the degradation by-product. These results are superior to those previously obtained by other reported methods. The new method was validated in terms of its selectivity, intra- and interday repeatability and accuracy, and sample storage stability, following the guidelines issued by the European Medicines Agency. Considering the convenient pretreatment procedure (LLE), superior sensitivity, and fast analysis speed (<15 min), this method can be useful in the determination of imatinib levels in blood.     

Development and validation of a novel sensitive UV‐direct capillary electrophoresis method for quantification of alendronate in release studies from biomaterials

A simple, highly sensitive, and robust CE method applied to the determination of alendronate (ALN) was developed from matrices for tissue engineering, characterized by being highly complex systems. The novel method was based on the ALN derivatization with o‐phthalaldehyde and 2‐mercaptoethanol for direct ultraviolet detection at 254 nm. The BGE consisted of 20 mM sodium borate buffer at pH 10, and the electrophoretic parameters were optimized.The method was validated in terms of specificity, linearity, LOD, LOQ, precision, accuracy, and robustness. The LOD and LOQ obtained were 0.8 and 2.7 μg/mL, respectively. In addition, the method offers higher sensitivity and specificity compared to other CE and HPLC methods using UV‐detectors, as well as low cost and simplicity that allowed the rapid and simple quantitation of ALN from bone regeneration matrices.     

Graphene quantum dots for enhancement of fluorimetric detection coupled to capillary electrophoresis for detection of ofloxacin

A new CE method with fluorescence detection is reported on the determination of ofloxacin in milk samples using graphene quantum dots (GQDs) for sensitivity enhancement. Injection of GQDs prior the standards/sample is crucial to increase the antibiotic fluorescence response. Clean‐up and preconcentration steps allowed for a good linear correlation in a concentration range between 50 and 1000 ng/mL for the ofloxacin, detection and quantification limits being 10.7 and 35.5 ng/mL, respectively. Optimal CE conditions for the seven‐fluoroquinolone separation method were assessed in terms of buffer type, pH, and voltage. The selective interaction of GQDs with ofloxacin as model analyte was subsequently studied finding a significant sensitivity improvement; therefore, the analytes would be detected at low concentrations by means of a commercial CE device equipped with a multi‐wavelength photoluminescence detector. Due to the different maximum emission wavelengths of the target compounds and the limitations shown by the single‐wavelength photoluminescence detector coupled to the CE system, we demonstrated the usefulness of the GQD‐assisted sensitivity‐enhanced CE method to determine ofloxacin in milk samples. This work opens an interesting possibility of using GQDs in separation techniques combined with photoluminescence detectors for lowering sensitivity levels typically provided by the mere device.     

Quantitative analysis of microcystin variants by capillary electrophoresis mass spectrometry with dynamic pH barrage junction focusing

Dynamic pH junction is an online focusing method in CE based on the electrophoretic mobility difference of analytes in the sample matrix and the background electrolyte. An advantage of this method over the conventional CE is that the sensitivity can be significantly improved. By injecting a long sample plug in the capillary and focusing the analytes at the pH boundary between the background electrolyte and sample matrix, the LOD can be improved by 10–100 folds. The dynamic pH junction method can be easily coupled with ESI‐MS. In this work, we used this method for the analysis of microcystins (MCs). The detection limits and dynamic ranges were studied. The separation was optimized by adjusting the injection time, and concentrations and pH values of the background electrolyte. The optimization of analyte focusing leads to enhanced detection response compared to conventional injections, achieving 200–400 fold higher averaged peak heights for four microcystin (MC) variants. More importantly, this method was successfully used for the quantitative analysis of microcystins (MCs) in crude algae samples from natural water bodies, making it promising for practical applications.     

Analysis of alendronate in human urine and plasma by magnetic solid-phase extraction and capillary electrophoresis with fluorescence detection

A simple, rapid and sensitive CE-fluorescence (FL) detection method for the analysis of alendronate (ALEN), a bisphosphonate drug, has been developed. Using a buffer solution of 20 mM sodium phosphate (pH 10.0) and a voltage of 24 kV, separation of ALEN in a 55-cm length (35-cm effective length) capillary was achieved in 5 min. FL detection of ALEN was performed via pre-column derivatization with 2,3-naphthalene dicarbox-yaldehyde (NDA). Linear correlation (r=0.9981, n=6) between FL intensity and analyte concentration was obtained in the range of 7-200 ng/mL ALEN. The developed CE-FL method was applied to the analysis of ALEN in human urine and plasma samples. In order to eliminate the interfering matrix components, SPE using magnetic Fe(3) O(4) @Al(2) O(3) nanoparticles as solid sorbents was employed to clean the biological fluids before CE-FL analysis. The linear ranges of ALEN in urine and plasma were 5-100 ng/mL (r = 0.9982, n = 7) and 5-70 ng/mL (r = 0.9954, n = 7), respectively. The LOD and LOQ in both urine and plasma samples were 1.5 and 5 ng/mL ALEN, respectively. Total analysis time including sample pre-treatment and CE separation was less than 1.5 h.     

Quantification of 5‐aminolevulinic acid by CE using dynamic pH junction technique

An online dynamic pH junction preconcentration method was developed for quantification of 5‐aminolevulinic acid (ALA) by CE with the separation time less than 6 min. The optimal dynamic pH junction of ALA was carried out between pH 9.3 borate buffer (BGE, 40 mM) and pH 2.5 phosphate buffer (sample matrix, 40 mM) when 4.1 cm of sample plug was hydrodynamically injected into an uncoated fused‐silica capillary (48.5 cm in length, id of 50 μm). If a 24 kV separation voltage was applied, the calibration curve of ALA peak area (200 nm) showed good linearity (R² = 0.9991) ranging from 0.01 to 6.5 mg/mL. The reproducibility of this system was excellent with RSDs (n = 10) of 2.5% for peak area response and 0.6% for migration time at ALA concentration of 0.5 mg/mL. The LOD was evaluated as 1.0 μg/mL (S/N > 3). Compared to conventional CE procedure, the sensitivity was successfully improved over 50‐fold. The analytical results of pharmaceutical formulations show a good agreement with those by HPLC (r = 0.94).     

Single-step analysis of low abundance phosphoamino acids via on-line sample preconcentration with chemical derivatization by capillary electrophoresis

New strategies for rapid, sensitive and high-throughput analysis of low abundance metabolites in biological samples are required for future metabolomic research. In this report, a direct method for sub-micromolar analyses of phosphoamino acids was developed using on-line sample preconcentration with 9-fluorenylmethyloxycarbonyl chloride (FMOC) derivatization by capillary electrophoresis (CE) and UV detection. Analyte focusing by dynamic pH junction and FMOC labeling efficiency were influenced by several experimental factors including buffer pH, ionic strength, sample injection length and FMOC concentration. About a 200-fold enhancement in concentration sensitivity was achieved under optimal conditions relative to conventional off-line derivatization, as reflected by a detection limit (S/N approximately 3) of 0.1 microM. In-capillary sample preconcentration with chemical labeling by CE offers a unique single-step analytical platform for high-throughput screening of low abundance metabolites without intrinsic chromophores.     

Ultratrace-level determination of glyphosate,aminomethylphosphonic acid and glufosinate in natural waters by solid-phase extraction followed by liquid chromatography–tandem mass spectrometry: performance tuning of derivatization,enrichment and detection

A sensitive and robust analytical method for the quantification of glyphosate, aminomethylphosphonic acid (AMPA) and glufosinate in natural water has been developed on the basis of a derivatization with 9-fluorenylmethylchloroformate (FMOC-Cl), solid-phase extraction (SPE) and liquid chromatography followed by electrospray tandem mass spectrometry (LC-ESI-MS/MS). In order to maximize sensitivity, the derivatization was optimized regarding organic solvent content, amount of FMOC-Cl and reaction time. At an acetonitrile content of 10% a derivatization yield of 100% was reached within two hours in groundwater and surface water samples. After a twofold dilution the low acetonitrile content allowed solid-phase extraction of a sample of originally 80 mL over 200 mg Strata-X cartridges. In order to decrease the load of the LC column and mass spectrometer with derivatization by-products (e.g., 9-fluorenylmethanol FMOC-OH), a rinsing step was performed for the SPE cartridge with dichloromethane. Acidification of the sample and addition of EDTA was used to minimize complexation of the target compounds with metal ions in environmental samples. Due to the large sample volume and the complete FMOC-OH removal, limits of quantification of 0.7 ng/L, 0.8 ng/L and 2.3 ng/L were achieved in surface water for glyphosate, AMPA and glufosinate, respectively. The limits of detection were as low as 0.2 ng/L, 0.2 ng/L and 0.6 ng/L for glyphosate, AMPA and glufosinate, respectively. Surface water and ground water samples spiked at 2 ng/L showed recoveries of 91–107%. Figure LC-MS/MS chromatogram of a water sample from a remote alpine region spiked at 1 ng/L     

芳香胺的碱坝聚焦-毛细管电泳分析

建立了碱坝聚焦-毛细管电泳方法, 实现了一些芳香胺的高灵敏检测. 该方法操作简单, 只需在大体积进样前先泵入一段NaOH溶液. 当进样5 cm长时, 间苯二胺、邻苯二胺及三聚氰胺的检出限可分别降至0.1, 0.05和0.05 μmol/L, 灵敏度比常规进样提高了100倍. 在2个量级浓度范围内, 各分析物峰面积与浓度具有良好的线性关系, 线性相关系数大于0.999. 该法可用于分析染发剂样品.     

Use of high‐conductivity sample solution with sweeping‐micellar electrokinetic capillary chromatography for trace‐level quantification of paliperidone in human plasma

Paliperidone is a new antipsychotic drug with a relatively low therapeutic concentration of 20–60 ng/mL. We established an accurate and sensitive CE method for the determination of paliperidone concentrations in human plasma in this study. To minimize matrix effect caused by quantification errors, paliperidone was extracted from human plasma using Oasis HLB SPE cartridges with three‐step washing procedure. To achieve sensitive quantification of paliperidone in human plasma, a high‐conductivity sample solution with sweeping‐MEKC method was applied for analysis. The separation is performed in a BGE composed of 75 mM phosphoric acid, 100 mM SDS, 12% acetonitrile, and 15% tetrahydrofuran. Sample solution consisted of 10% methanol in 250 mM phosphoric acid and the conductivity ratio between sample matrix and BGE was 2.0 (γ, sample/BGE). The results showed it able to detect paliperidone in plasma samples at concentration as low as 10 ng/mL (S/N = 3) with a linear range between 20 and 200 ng/mL. Compared to the conventional MEKC method, the sensitivity enhancement factor of the developed sweeping‐MEKC method was 100. Intra‐ and interday precision of peak area ratios were less than 6.03%; the method accuracy was between 93.4 and 97.9%. This method was successfully applied to the analysis of plasma samples of patients undergoing paliperidone treatment.     

Determination of urinary androgen glucuronides by capillary electrophoresis with electrospray tandem mass spectrometry

Capillary electrophoresis–electrospray tandem mass spectrometry (CE‐ESI/MS/MS) is a simple and highly sensitive method for quantifying seven urinary androgen glucuronides. The urine samples were diluted and filtered through a membrane filter, and the filtrate was injected into a CE‐MS/MS system without further sample preparation steps such as extraction and derivatization. The calibration ranges were 0.01–5 µg/mL for glucuronides of androsterone and 11β‐OHAn‐3G, and 5–500 ng/mL for glucuronides of 11‐ketoAn, DHEA, testosterone, epitestosterone and DHT. The linearity of the method was 0.992–0.998, and the limits‐of‐detection at a signal‐to‐noise ratio of 3 were 5–10 ng/mL. The coefficients of variation were in the range of 4.0–9.0% for intra‐day assay and 4.1–9.8% for inter‐day assay. The proposed method may be applicable to metabolic profiling in both quantitative and qualitative analysis. Copyright © 2008 John Wiley & Sons, Ltd.     

Analysis of brazilin and protosappanin B in sappan lignum by capillary zone electrophoresis with acid barrage stacking

A method was developed to determine brazilin and protosappanin B in natural products by CE after acid barrage stacking. The optimum conditions were as follows: a BGE of 20 mM sodium tetraborate (pH 9.2) containing 6% v/v of methanol, hydrodynamic injection (0.5 psi, 65 s) followed by hydrodynamic injection of 150 mM citric acid (pH 2.3; 0.5 psi, 22 s), and separated with +25 kV. Under these conditions, brazilin and protosappanin B were separated with a sample‐to‐sample time less than 13 min and detection limits of 0.28 μg/mL and 0.15 μg/mL, respectively. The applicability of the developed method was demonstrated by the detection of brazilin and protosappanin in methanol extract of sappan lignum.     

Quantitative determination of acidic hydrolysis products of Chemical Weapons Convention related chemicals from aqueous and soil samples using ion‐pair solid‐phase extraction and in situ butylation

Chemical warfare agents such as organophosphorus nerve agents, mustard agents, and psychotomimetic agent like 3‐quinuclidinylbenzilate degrade in the environment and form acidic degradation products, the analysis of which is difficult under normal analytical conditions. In the present work, a simultaneous extraction and derivatization method in which the analytes are butylated followed by gas chromatography and mass spectrometric identification of the analytes from aqueous and soil samples was carried out. The extraction was carried out using ion‐pair solid‐phase extraction with tetrabutylammonium hydroxide followed by gas chromatography with mass spectrometry in the electron ionization mode. Various parameters such as optimum concentration of the ion‐pair reagent, pH of the sample, extraction solvent, and type of ion‐pair reagent were optimized. The method was validated for various parameters such as linearity, accuracy, precision, and limit of detection and quantification. The method was observed to be linear from 1 to 1000 ng/mL range in selected ion monitoring mode. The extraction recoveries were in the range of 85–110% from the matrixes with the limit of quantification for alkyl phosphonic acids at 1 ng/mL, thiodiglycolic acid at 20 ng/mL, and benzilic acid at 50 ng/mL with intra‐ and interday precisions below 15%. The developed method was applied for the samples prepared in the scenario of challenging inspection.     

Steroselective determination of trihexyphenidyl using carboxylmethyl-β-cyclodextrin by capillary electrophoresis with field-amplified sample stacking

A simple, sensitive and low-cost method using capillary electrophoresis coupled with field-amplified sample stacking (FASS) technique has been developed for enantioselective separation and quantification of trihexyphenidyl (THP) enantiomers in human serum. In this work, three kinds of modified β-cyclodextrin were tested as chiral selectors in CE. Among the CDs studied, THP enantiomers could only be separated by carboxylmethyl-β-cyclodextrin (CM-β-CD). A systematic study of the parameters (CD concentration and pH value in CE buffer, separation voltage and temperature, composition of sample solvent, injection voltage and time) affecting chiral separation and on-line concentration of THP enantiomers were investigated and optimized. The optimum FASS method provided a sensitivity enhancement of about 490-fold compared with usual hydrodynamic injection. Limits of detection for each enantiomer were in the low ng ml^− 1 concentration range (0.92 ng ml^− 1 or 3.06 nM). The quantification of each THP enantiomer in human serum was performed after serum sample extraction. To validate this CE-FASS method, linear regression analysis, intra and inter-day precision and recovery were determined with satisfying results.     

Microemulsion electrokinetic chromatography: an application for the simultaneous determination of suspected fragrance allergens in rinse-off products

The feasibility of microwave-accelerated derivatization for capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection was evaluated. The derivatization reaction was performed in a domestic microwave oven. Histidine (His), 1-methylhistidine (1-MH) and 3-methylhistidine (3-MH) were selected as test analytes and fluorescein isothiocyanate (FITC) was chosen as a fluorescent derivatizing reagent. Parameters that may affect the derivatization reaction and/or subsequent CE separation were systematically investigated. Under optimized conditions, the microwave-accelerated derivatization reaction was successfully completed within 150 s, compared to 4-24 h in a conventional water-bath derivatization process. This will remarkably reduce the overall analysis time and increase sample throughput of CE-LIF. The detection limits of this method were found to be 0.023 ng/mL for His, 0.023 ng/mL for 1-MH, and 0.034 ng/mL for 3-MH, respectively, comparable to those obtained using traditional derivatization protocols. The proposed method was characterized in terms of precision, linearity, accuracy and successfully applied for rapid and sensitive determination of these analytes in human urine.     

Improved determination of the bisphosphonate alendronate in human plasma and urine by automated precolumn derivatization and high-performance liquid chromatography with fluorescence and electrochemical detection.

An improved method for the determination of 4-amino-1-hydroxybutane-1,1-bisphosphonic acid (alendronate) in human urine and an assay in human plasma are described. The methods are based on co-precipitation of the bisphosphonate with calcium phosphates, automated pre-column derivatization of the primary amino group of the bisphosphonic acid with 2,3-naphthalene dicarboxyaldehyde (NDA)-N-acetyl-D-penicillamine (NAP) or cyanide (CN-) reagents, and high-performance liquid chromatography (HPLC) with electrochemical (ED) or fluorescence detection (FD). The feasibility of ED of the NDA-CN- derivative of aldendronate has been demonstrated, and a HPLC-ED assay in human urine has been validated in the concentration range 2.5-50.0 ng/ml. In order to eliminate the cyanide ion from the assay procedure, several other nucleophiles in the NDA derivatization reaction were evaluated. An NDA-NAP reagent was found to produce highly fluorescent derivatives of alendronate. The assay in urine based on NDA-NAP derivatization and HPLC-FD has been developed and fully validated in the concentration range 1-25 ng/ml. Based on the same NDA-NAP derivatization, an assay in human plasma with a limit of quantification of 5 ng/ml has also been developed. Both HPLC-FD assays were utilized to support various human pharmacokinetic studies with alendronate.     

Electrokinetic supercharging preconcentration prior to CGE analysis of DNA: Sensitivity depends on buffer viscosity and electrode configuration

Aiming to high sensitivity DNA analysis by CGE, electrokinetic supercharging (EKS) approach was adopted in this article. EKS is known as an online preconcentration technique that combines electrokinetic sample injection (EKI) with transient ITP (tITP). Herein, two factors of buffer viscosity and electrode configuration were studied to further improve EKS performance. An ultralow‐viscosity Tris‐Boric acid‐EDTA (TBE) buffer solution, consisted of 2% low‐molecular‐weight hydroxypropyl methyl cellulose (HPMC) and 6% mannitol and with pH 8.0 adjusted by boric acid, was applied. The boric acid would make a complex with mannitol and generates borate polyanion, which acts as the leading ion for tITP process. The new electrode configuration, a Pt ring around capillary, was modified on Agilent CE system to lead large amount sample introduction during EKS. The standard DNA sample of φX174/HaeIII digest was used to evaluate the qualitative and quantitative abilities of the proposed strategy. The 170 000‐fold highly diluted sample at concentration of 3.0 ng/mL was enriched by EKS and detected by normal UV detection method. The obtained LOD of the weakest peak of 72 bp fragment was around 7.7 pg/mL, apparently improved more than 10 000‐fold in comparison with conventional CGE with UV detection.     

Online preconcentration of arsenic compounds by dynamic pH junction-capillary electrophoresis

An online preconcentration technique by dynamic pH junction was studied to improve the detection limit for anionic arsenic compounds by CE. The main target compound is roxarsone, or 3-nitro-4-hydroxyphenylarsonic acid, which is being used as an animal feed additive. The other inorganic and organoarsenic compounds studied are the possible biotransformation products of roxarsone. The arsenic species were separated by a dynamic pH junction in a fused-silica capillary using 15 mM phosphate buffer (pH 10.6) as the BGE and 15 mM acetic acid as the sample matrix. CE with UV detection was monitored at a wavelength of 192 nm. The influence of buffer pH and concentration on dynamic pH junction were investigated. The arsenic species focusing resulted in LOD improvement by a factor of 100-800. The combined use of C18 and anion exchange SPE and dynamic pH junction to CE analysis of chicken litter and soils helps to increase the detection sensitivity. Recoveries of spiked samples ranged between 70 and 72%.