Evaluation of the fuel cell performances of TiO2/PAN electrospun carbon-based electrodes

Electrocatalytic effect of the untreated and TiO₂+polyacrylonitrile (PAN) modified discarded battery coal (DBC) and pencil graphite electrodes (PGE) were evaluated in fuel cell (FC) applications. TiO₂+PAN solution is coated on PGE and DBC electrodes by electrospinning. According to the FESEM and EDS characterizations, TiO₂ and PAN nanofibers are found to be approximately 40 and 240 nm in size. TiO₂+PAN/PGE showed the best FC performances with 2.00 A cm^–2 current density and 5.05 W cm^–2 power density values, whereas TiO₂+PAN/DBC showed 0.68 A cm^–2 current density and 0.62 W cm^–2 power density values. Electrochemical characterizations of PGE and TiO₂+PAN/PGE electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Finally, long-term FC measurement results of developed electrodes exhibited very reasonable recovery values. Along with the comparison of the electrode performances, the recovery of DBCs as electrodes for renewable energy production has been achieved.     

Dramatically Enhanced Li-Ion Storage of ZnO@C Anodes through TiO2 Homogeneous Hybridization

Amorphous nanoparticles of ZnO and TiO₂ embedded in carbon nanocages (AZT⊂CNCs) were successfully synthesized through a simple annealing process of TiO₂-coated zeolitic imidazolate framework-8 (ZIF-8). In the current anode of AZT⊂CNCs, tiny ZnO and TiO₂ nanoparticles were uniformly distributed in the carbon matrix (carbon nanocages), which could effectively buffer the volume expansion of electroactive ZnO and provide excellent electric conductivity. After fully investigating the electrochemical performance of the AZT⊂CNCs samples obtained with different additive amounts of tetrabutyl orthotitanate (TBOT) for TiO₂ coating, it has been found that AZT-30 (0.1 g ZIF-8 with 30 mL TBOT) shows the best cycle stability (510 mA h g⁻¹ after 350 cycles at 200 mA g⁻¹) and a superior rate capability (610 mA h g⁻¹ after 3500 cycles at 2 A g⁻¹). The greatly enhanced Li-ion storage performance could be ascribed to the fact that the introduction of amorphous TiO₂ could activate the reversible lithiation/delithiation reaction of ZnO during the charge/discharge process.     

Enhanced electrochemical performance of carbon-coated TiO2 nanobarbed fibers as anode material for lithium-ion batteries

We report the electrochemical performance of carbon-coated TiO₂ nanobarbed fibers (TiO₂@C NBFs) as anode material for lithium-ion batteries. The TiO₂@C NBFs are composed of TiO₂ nanorods grown on TiO₂ nanofibers as a core, coated with a carbon shell. These nanostructures form a conductive network showing high capacity and C-rate performance due to fast lithium-ion diffusion and effective electron transfer. The TiO₂@C NBFs show a specific reversible capacity of approximately 170 mAh g^− 1 after 200 cycles at a 0.5 A g^− 1 current density, and exhibit a discharge rate capability of 4 A g^− 1 while retaining a capacity of about 70 mAh g^− 1. The uniformly coated amorphous carbon layer plays an important role to improve the electrical conductivity during the lithiation–delithiation process.     

Co9S8@CN Composites Obtained from Thiacalix[4]arene-Based Coordination Polymers for Supercapacitor Applications

Metal sulfides have been recognized as promising electrodes for electrochemical energy storage owing to their remarkable electrochemical properties. Here, we demonstrate the preparation of Co₉S₈ nanoparticles anchored on a carbon matrix (denoted as Co₉S₈-X@CN (X=1, 2)) from precursor sources, two 1D infinite coordination polymers 1 and 2 . The two polymers were assembled by linking Co₄-TC4A secondary building blocks (SBUs) with ligands L₁ and L₂, respectively (H₄TC4A=p-tert-butylthiacalix[4]arene, L₁=1,4-bis(2H-tetrazol-5-yl)benzene, L₂=1,3-bis(2H-tetrazol-5-yl)benzene). The composites obtained from 1D polymers showed different morphologies, that is, the Co₉S₈ nanoparticles of Co₉S₈-1@CN are octahedral with a size of ca. 140 nm, while the lamellar Co₉S₈ nanoparticles in Co₉S₈-2@CN possess different sizes (50–150 nm). The Co₉S₈-2@CN immobilized on nickel foam (Co₉S₈-2@CN/NF) show better supercapacitive performance than that of Co₉S₈-1@CN. Co₉S₈-2@CN showed exceptionally high activities, combining higher specific capacitances (445.2 F g⁻¹ at 2 A g⁻¹ and 393.9 F g⁻¹ and 5 A g⁻¹), rate capacity (94.5% retention at 2 A g⁻¹), and long-term stability (79.2% retention at 5 A g⁻¹ over 1000 cycles). The smaller size and larger BET surface area of Co₉S₈-2@CN nanoparticles can improve the electrical conductivity and provide facile pathways for charge transport, thus leading to conspicuous electrochemical performance of Co₉S₈-2@CN compared with its Co₉S₈-1@CN counterpart.     

Cobalt ion-doped polyaniline,poly(N-methylaniline), and poly(N-ethylaniline): electrosynthesis and characterisation using electrochemical methods in acidic solutions

Cobalt ion (Co²⁺)-doped polyaniline (PANI-Co), poly(N-methylaniline) (PNMA-Co), and poly(N-ethylaniline) (PNEA-Co) films were synthesised electrochemically on a pencil graphite electrode (PGE) and their electrochemical properties were investigated for supercapacitor applications. The polymer film-coated electrodes (PGE/PANI-Co, PGE/PNMA-Co, and PGE/PNEA-Co) thus obtained were characterised by scanning electron microscopy (SEM) and different electrochemical methods. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements were employed in 0.1 M H₂SO₄ solution to calculate the specific capacitance (C _S) values of the electrodes. The maximum C _S of 192.94 F g^?1, 139.83 F g^?1, and 47.12 F g^?1 were achieved for PGE/PANI-Co, PGE/PNMA-Co, and PGE/PNEA-Co at 1 mV s^?1, respectively. On the other hand, the charge/discharge stability of the electrodes was analysed using the repeating chronopotentiometry (RCP) method. The RCP measurements indicate that the electrodes could be used as an electrode active material for low voltage supercapacitor applications.     

Nb-doped rutile titanium dioxide nanorods for lithium-ion batteries

Rutile titanium dioxide is a promising negative electrode material for lithium-ion batteries due to low volume change on lithium-ion insertion, fast ion diffusion, and large surface area. However, the low theoretical capacity and conductivity of titanium dioxide has limited its application. In this work, rutile TiO₂ was synthesized using a batch hydrothermal method, and doped with Nb⁵⁺ (3.5 at%). <Potentiodynamic/galvanostatic > cycling in the range 1.0–3.0 V vs Li/Li⁺ was used to determine the Li-ion capacity of the doped and pristine TiO₂ material, and electrochemical cycling was used to measure the extent of conversion from the lithiated to de-lithiated state. The nanoscale structures of the pristine and doped materials were determined by powder X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy and Brunauer-Emmett-Teller surface area measurements. Cycling in the range 1.0–3.0 V vs Li/Li⁺ showed that Nb⁵⁺ doping into the structure resulted in higher charge capacities. After 100 cycles at 100 mA g⁻¹, the Nb-doped rutile TiO₂ maintained a capacity of ca. 390 mAh g⁻¹, 64% higher than undoped TiO₂. For electrochemical cycling in the range 0.05–3.0 V vs Li/Li⁺, the introduction of Nb⁵⁺ resulted in a higher conversion of rutile TiO₂ from the lithiated to de-lithiated state. The higher capacity of the doped TiO₂ is shown to be mainly due to the smaller particle size, optimized surface area, and orientation of the nanorods.     

Coordination polymer template synthesis of hierarchical MnCo2O4.5 and MnNi6O8 nanoparticles for electrochemical capacitors electrode

Two types of ternary metal oxides, MnCo₂O_4.5 and MnNi₆O₈ nanoparticles have been separately synthesized through chemical transformation from the corresponding bimetallic coordination polymer particles precursor under high-heating conditions. Series of electrochemical measurements are performed to examine the MnCo₂O_4.5 and MnNi₆O₈ electrodes, and the result shows that MnCo₂O_4.5 structure, especially for Mn/Co-600, has much higher capacitance than that of MnNi₆O₈ nanoparticles, indicating MnCo₂O_4.5 electrode is more suitable for applying in neutral electrolyte system. The Mn/Co-600 electrode exhibits a specific capacitance of 158 F g⁻¹ at 5 mV s⁻¹, good rate capability of 53.8% with a 20 times current density increase, good cycle performance (92.9% capacitance retention after 1000 cycles) and high power density (a specific power of 5760 W kg⁻¹ at 4.0 A g⁻¹) with low charge transfer resistance value of 1.8 Ω.     

Electrodeposition of MnO2 nanowires on carbon nanotube paper as free-standing,flexible electrode for supercapacitors

MnO₂ nanowires were electrodeposited onto carbon nanotube (CNT) paper by a cyclic voltammetric technique. The as-prepared MnO₂ nanowire/CNT composite paper (MNCCP) can be used as a flexible electrode for electrochemical supercapacitors. Electrochemical measurements showed that the MNCCP electrode displayed specific capacitances as high as 167.5 F g⁻¹ at a current density of 77 mA g⁻¹. After 3000 cycles, the composite paper can retain more than 88% of initial capacitance, showing good cyclability. The CNT paper in the composite acted as a good conductive and active substrate for flexible electrodes in supercapacitors, and the nanowire structure of the MnO₂ could facilitate the contact of the electrolyte with the active materials, and thus increase the capacitance.     

Facile synthesis of polyaniline/TiO2/graphene oxide composite for high performance supercapacitors

The polyaniline/TiO₂/graphene oxide (PANI/TiO₂/GO) composite, as a novel supercapacitor material, is synthesized by in situ hydrolyzation of tetrabutyl titanate and polymerization of aniline monomer in the presence of graphene oxide. The morphology, composition and structure of the composites as-obtained are characterized by SEM, TEM, XRD and TGA. The electrochemical property and impedance of the composites are studied by cyclic voltammetry and Nyquist plot, respectively. The results show that the introduction of the GO and TiO₂ enhanced the electrode conductivity and stability, and then improved the supercapacitive behavior of PANI/TiO₂/GO composite. Significantly, the electrochemical measurement results show that the PANI/TiO₂/GO composite has a high specific capacitance (1020 F g⁻¹ at 2 mV s⁻¹, 430 F g⁻¹ at 1 A g⁻¹) and long cycle life (over 1000 times).     

Multi-stage Ordered Mesoporous Carbon-graphene Aerogel-Ni3S2/Co4S3 for Supercapacitor Electrode

Transition metal sulfides have emerged as promising materials in supercapacitor. In this work, we firstly developed an interface-induced superassembly approach to fabricate NiS_x and CoS_x nanoparticles, which based on ordered mesoporous carbon-graphene aerogel composites for supercapacitor electrodes. The obtained multi-component superassembled nanoparticles-carbon matrix composites have controllable 3D porous structure of multi-stage composite. The two-dimensional graphene interlaced to form a 3D framework with large sponge-like pores, and then the graphene surface was loaded with mesoporous carbon with mesoporous pore size and vertical orientation. The composites display high specific capacitance of 958.1 F g⁻¹ at 0.1 A g⁻¹. The capacitance retains about 97.3 % after 3000 charging-discharging cycles at 2 A g⁻¹. These results indicate that the obtained OMC−GA−Ni₃S₂/Co₄S₃ is a promising material for electrochemical capacitors, which providing new technical methods and ideas for the research of new energy and analytical sensor materials in the fields of energy storage, photocatalysis, point-of-care testing devices and other fields.     

Disclosing Support-Size-Dependent Effect on Ambient Light-Driven Photothermal CO2 Hydrogenation over Nickel/Titanium Dioxide

The size of support in heterogeneous catalysts can strongly affect the catalytic property but is rarely explored in light-driven catalysis. Herein, we demonstrate the size of TiO₂ support governs the selectivity in photothermal CO₂ hydrogenation by tuning the metal-support interactions (MSI). Small-size TiO₂ loading nickel (Ni/TiO₂-25) with enhanced MSI promotes photo-induced electrons of TiO₂ migrating to Ni nanoparticles, thus favoring the H₂ cleavage and accelerating the CH₄ formation (227.7 mmol g⁻¹ h⁻¹) under xenon light-induced temperature of 360 °C. Conversely, Ni/TiO₂-100 with large TiO₂ prefers yielding CO (94.2 mmol g⁻¹ h⁻¹) due to weak MSI, inefficient charge separation, and inadequate supply of activated hydrogen. Under ambient solar irradiation, Ni/TiO₂-25 achieves the optimized CH₄ rate (63.0 mmol g⁻¹ h⁻¹) with selectivity of 99.8 %, while Ni/TiO₂-100 exhibits the CO selectivity of 90.0 % with rate of 30.0 mmol g⁻¹ h⁻¹. This work offers a novel approach to tailoring light-driven catalytic properties by support size effect.     

Nano-p–n junction heterostructures enhanced TiO2 nanobelts biosensing electrode

6-Phosphate aminopurine (⁶PA), a purine analog, is usually used in clinical anticancer treatment and biochemical research. Up to now, to the best of our knowledge, no literature about the electrochemical behaviors of ⁶PA has been reported. In this study, nano-p–n junction heterostructures based on TiO₂ nanobelts were produced by the assembly of p-type semiconducting NiO nanoparticles onto the n-type surface-coarsened TiO₂ nanobelts. The electrochemical behaviors of ⁶PA were investigated by different voltammetric techniques in a phosphate buffer solution of pH 7.4 using the heterostructures as the sensing electrode. Compared with single-phase TiO₂ nanobelt electrodes, the resulting chemically modified electrodes exhibited higher surface accumulation ability and enhanced electrocatalytic activities in the oxidation for ⁶PA, with an irreversible oxidation peak at +0.91 V. It is proposed that the nano-p–n junction heterostructures played an important role in the enhancement of charge transport in the sensing electrodes. The results suggest that the nanoengineered TiO₂ nanobelts might be a promising candidate for biosensing applications of nucleic acid drugs that will be of significance to diagnostic medicine and molecular biology research.     

Optimizing carbon coating parameters for obtaining SiO2/C anodes with improved electrochemical performance

In this work, we present a comprehensive and systematic study on the use of low-cost and highly abundant carbon precursors to obtain SiO₂/C anodes with superior electrochemical performance towards Li-ions. Different SiO₂/C composites are prepared by soaking silica nanoparticles in solutions containing 20 wt%, 40 wt%, or 60 wt% of glucose, sucrose, or cornstarch, followed by thermal decomposition of the carbohydrates at 850 °C or 1200 °C. Structural, microstructural, and textural differences on the composites derived from the different carbon coating treatments are related to the electrochemical performance of the anodes. Composites containing final carbon contents close to 15 wt% show a complete coverage of the SiO₂ particles with a nanometric carbon layer and exhibit the best electrochemical results. The increase in the annealing temperature from 850 to 1200 °C reduces the porosity of the carbon layer and increases its level of ordering, both having positive effects on the overall electrochemical performance of the electrodes. SiO₂/C composites coated with 40 wt% sucrose and heat treated at 1200 °C display the best electrochemical performance, delivering a reversible specific capacity of 723 mAhg⁻¹ at 50 mAg⁻¹ after 100 cycles, which is considerably higher than the reversible capacity of 233 mAhg⁻¹ obtained with the uncoated material cycled under the same conditions.

     

One-pot hydrothermal synthesis of porous anatase TiO2 nanotube formed bundles for lithium ion battery anodes

Anatase phase of TiO₂ nanomaterial has been deemed a potential anode material for lithium ion battery (LIB) applications because of its remarkable electrochemical properties. However, TiO₂ anodes always suffer from intrinsic poor electrical conductivity and slow ion kinetics, which would restrict their practical usage. To address this issue, efficient control and design of the anatase crystal structure of TiO₂ material with desirable morphology is one of the critical approaches. In this work, a good lithium storage capability of 181 mA hr g⁻¹ at rate of 0.2C, high rate performance of 70 mA hr g⁻¹ at 20C, and excellent cyclability of 117 mA hr g⁻¹ with a capacity retention of 93% at 1C after 100 cycles and 84 mA hr g⁻¹ at 10C after 1,000 cycles are observed in an optimized porous anatase TiO₂ one-dimensional nanotube bundle nanomaterial fabricated through a simple hydrothermal process with post calcination treatment. These excellent electrochemical properties of the product can be ascribed to its anatase crystal phase, 1D nanostructure, and porous framework with a large surface area, which provide it with an efficient electrode/electrolyte contact area and a faster ion/electron diffusion pathway.     

The preparation,characterization, photoelectrochemical and photocatalytic properties of lanthanide metal-ion-doped TiO2 nanoparticles

Lanthanide metal-ion-doped TiO₂ nanoparticles were prepared with hydrothermal method and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), inductively coupled plasma (ICP) and fluorescence spectrum. The results showed that a small part of metal ions entered into the lattice of TiO₂ and others adsorbed on the surface of TiO₂. The photoelectrochemical and photocatalytic properties of these lanthanide metal-ion-doped TiO₂ nanoparticles were investigated and the results showed that the photoresponse of Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ electrodes were much larger and that of Sm³⁺-doped TiO₂ electrode was a little larger than that of undoped TiO₂ electrode, indicating that the photogenerated carriers were separated more efficiently in Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ nanoparticles than in undoped TiO₂ nanoparticles. The photocatalytic degradation of rhodamine B (RB) was conducted in the suspension of lanthanide metal-ion-doped TiO₂ nanoparticles, and its first-order reaction rate constant (k) and average initial rate (r_ini) were significantly higher in the presence of Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ nanoparticles than those in the presence of undoped TiO₂ nanoparticles. The enhanced photocatalytic degradation rate of RB in the presence of Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ nanoparticles is attributed to increased charge separation in these systems. The effect of the content of La³⁺ on the reaction parameters (k and r_ini) was also investigated and the result showed that there was an optimal value (ca. 0.5%) of the content of La³⁺ to make the rate constant (k) and average initial rate (r_ini) reach the maxima.     

Electrochemical Biosensing for Cancer Cells Based on TiO2/CNT Nanocomposites Modified Electrodes

Both TiO₂ nanoparticles and carbon nanotubes have been usually utilized to modify the electrodes to enhance the detection sensitivity of biomolecular recognition. In this research, novel TiO₂/CNT nanocomposites have been prepared and doped on the carbon paper as the modified electrodes. Subsequently, the redox behavior of the ferricyanide probe and the surface properties of the cancer cells coated on the modified electrodes have been investigated by using electrochemical and contact angle measurements. Compared with electrochemical signals on bare carbon paper and nanocomposite modified substrates, the significantly enhanced electrochemical signals on the modified electrodes covered with cancer cells have been observed. Meanwhile, different leukemia cells (i.e., K562/ADM cells and K562/B.W. cells) could be also recognized because of their different electrochemical behavior and hydrophilic/hydrophobic features on the modified electrodes due to the specific components on the plasma membranes of the target cells. This new strategy may have potential application in the development of the biocompatible and multi‐signal responsive biosensors for the early diagnosis of cancers.     

银负载量对网状TiO2柔性薄膜电极储锂性能的影响

本工作采用水热法结合银镜反应制备出一系列不同Ag负载量（2.2%、4.0%、6.4%,w/w）改性的3D纳米网状结构Ag@TiO₂薄膜电极。利用电感耦合等离子体技术（ICP）、X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）和X射线能谱（EDX）等表征手段测试所合成材料的形貌及成分,实验结果表明Ag纳米颗粒可以成功沉积在TiO₂纳米线表面。电化学测试数据则表明,4.0%（w/w）负载量的Ag@TiO₂相比于未改性和其他负载量的TiO₂纳米线具有更好的倍率性能和更稳定的可逆容量。在50,100,200,400,800和1 200 mA·g^-1的电流密度条件下,该改性电极的放电容量可分别达到261.4,253.7,239.5,216.5,193.1和185.1 mAh·g^-1,在200 mA·g^-1下循环80次后容量保持率仍能达到99.8%。     

Consecutive Charging of a Perylene Bisimide Dye by Multistep Low-Energy Solar-Light-Induced Electron Transfer Towards H2 Evolution

A photocatalytic system containing a perylene bisimide (PBI) dye as a photosensitizer anchored to titanium dioxide (TiO₂) nanoparticles through carboxyl groups was constructed. Under solar-light irradiation in the presence of sacrificial triethanolamine (TEOA) in neutral and basic conditions (pH 8.5), a reaction cascade is initiated in which the PBI molecule first absorbs green light, giving the formation of a stable radical anion (PBI^.−), which in a second step absorbs near-infrared light, forming a stable PBI dianion (PBI²⁻). Finally, the dianion absorbs red light and injects an electron into the TiO₂ nanoparticle that is coated with platinum co-catalyst for hydrogen evolution. The hydrogen evolution rates (HERs) are as high as 1216 and 1022 μmol h⁻¹ g⁻¹ with simulated sunlight irradiation in neutral and basic conditions, respectively.     

银负载量对网状TiO_2柔性薄膜电极储锂性能的影响

采用水热法结合银镜反应制备出一系列不同Ag负载量(2.2%、4.0%、6.4%,w/w)改性的3D纳米网状结构Ag@Ti O2薄膜电极。利用电感耦合等离子体技术(ICP)、X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和X射线能谱(EDX)等表征手段测试所合成材料的形貌及成分,实验结果表明Ag纳米颗粒可以成功沉积在Ti O2纳米线表面。电化学测试数据则表明,4.0%(w/w)负载量的Ag@Ti O2相比于未改性和其他负载量的Ti O2纳米线具有更好的倍率性能和更稳定的可逆容量。在50,100,200,400,800和1 200 m A·g~(-1)的电流密度条件下,该改性电极的放电容量可分别达到261.4,253.7,239.5,216.5,193.1和185.1 m Ah·g~(-1),在200 m A·g~(-1)下循环80次后容量保持率仍能达到99.8%。     

Hierarchical FeCo2S4@FeNi2S4 Core/Shell Nanostructures on Ni Foam for High-Performance Supercapacitors

The design of electrode materials with rational core/shell structures is promising for improving the electrochemical properties of supercapacitors. Hence, hierarchical FeCo₂S₄@FeNi₂S₄ core/shell nanostructures on Ni foam were fabricated by a simple hydrothermal method. Owing to their structure and synergistic effect, they deliver an excellent specific capacitance of 2393 F g⁻¹ at 1 A g⁻¹ and long cycle lifespan as positive electrode materials. An asymmetric supercapacitor device with FeCo₂S₄@FeNi₂S₄ as positive electrode and graphene as negative electrode exhibited a specific capacitance of 133.2 F g⁻¹ at 1 A g⁻¹ and a high energy density of 47.37 W h kg⁻¹ at a power density of 800 W kg⁻¹. Moreover, the device showed remarkable cycling stability with 87.0 % specific-capacitance retention after 5000 cycles at 2 A g⁻¹. These results demonstrate that the hierarchical FeCo₂S₄@FeNi₂S₄ core/shell structures have great potential in the field of electrochemical energy storage.