High-flux nanofiltration membranes prepared by adsorption of multilayer polyelectrolyte membranes on polymeric supports

Layer-by-layer deposition of anionic and cationic polyelectrolytes readily converts polymeric ultrafiltration membranes into materials capable of nanofiltration. ATR-FTIR spectra confirm that layer-by-layer deposition occurs on the ultrafiltration substrates, and adsorption of as few as 2.5 bilayers of poly(styrenesulfonate) (PSS)/protonated poly(allylamine) (PAH) or 3.5 bilayers of PSS/poly(diallyldimethylammonium chloride) (PDADMAC) reduces the molecular weight cutoff of polyethersulfone ultrafiltration supports from 50 kDa to <500 Da. Deposition of multilayer polyelectrolyte films on 300 and 500 kDa membranes also decreases molecular weight cutoffs, but solute rejections are significantly lower when using these supports, suggesting that the polyelectrolyte films do not completely cover large (0.2-0.4 microm in diameter) pores. On the 50 kDa substrates, PSS/PDADMAC films containing 3.5 bilayers exhibit a 95% rejection of SO(4)(2-) and a chloride/sulfate selectivity of 27, whereas 4.5-bilayer PSS/PAH coatings show a glucose/raffinose selectivity of 100. Pure water flux for [PSS/PAH](3)PSS-coated membranes at 4.8 bar is 1.6 m(3)/(m(2)day), which is more than 2-fold higher than that through a commercial 500 Da membrane.     

Polyelectrolyte blend multilayer films: surface morphology, wettability, and protein adsorption characteristics

We report the influence of polyelectrolyte (PE) multilayer films prepared from poly(styrene sulfonate)-poly(acrylic acid) (PSS-PAA) blends, deposited in alternation with poly(allylamine hydrochloride) (PAH), on film wettability and the adsorption behavior of the protein immunoglobulin G (IgG). Variations in the chemical composition of the PAH/(PSS-PAA) multilayer films, controlled by the PSS/PAA blend ratio in the dipping solutions, were used to systematically control film thickness, surface morphology, surface wettability, and IgG adsorption. Spectroscopic ellipsometry measurements indicate that increasing the PSS content in the blend solutions results in a systematic decrease in film thickness. Increasing the PSS content in the blend solutions also leads to a reduction in film surface roughness (as measured by atomic force microscopy), with a corresponding increase in surface hydrophobicity. Advancing contact angles (theta) range from 7 degrees for PAH/PAA films through to 53 degrees for PAH/PSS films. X-ray photoelectron spectroscopy measurements indicate that the increase in film hydrophobicity is due to an increase in PSS concentration at the film surface. In addition, the influence of added electrolyte in the PE solutions was investigated. Adsorption from PE solutions containing added salt favors PSS adsorption and results in more hydrophobic films. The amount of IgG adsorbed on the multilayer films systematically increased on films assembled from blends with increasing PSS content, suggesting strong interactions between PSS in the multilayer films and IgG. Hence, multilayer films prepared from blended PE solutions can be used to tune film thickness and composition, as well as wetting and protein adsorption characteristics.     

Modulation of hemocompatibility of polysulfone by polyelectrolyte multilayer films

Polyelectrolyte multilayer (PEM) films have been recently applied to surface modification of biomaterials. Cellular interactions with PEM films consisted of weak polyelectrolytes are greatly affected by the conditions of polyelectrolyte deposition, such as pH of polyelectrolyte solution. Previous studies indicated that the adhesion of several types of mammalian cells to PAH/PAA multilayer films was hindered by low pH and high layer numbers. The objective of this study is to evaluate whether the hemocompatibility of polysulfone can be modulated by deposition of poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) multilayer films. PAH/PAA multilayer films with different layer numbers were assembled onto polysulfone at either pH 2.0 or pH 6.5. The number of platelet adhesion and the morphology of adherent platelets were determined to evaluate hemocompatibility of modified substrates. Compared to non-treat polysulfone, the PEM films developed at pH 2.0 decreased platelet adhesion, while those built at pH 6.5 enhanced platelet deposition. Platelet adhesion was found positively correlated to polyclonal antibodies binding to surface-bound fibrinogen. The extent of platelet spreading was increased with layer numbers of PEM films, suggesting that the adherent platelets on thick PEM films were prone to activation. In conclusion, PAH/PAA films with few layers developed at pH 2.0 possessed better hemocompatibility compared to other substrates.     

Fabrication of polyelectrolyte multilayer films comprising nanoblended layers

Polyelectrolyte multilayer thin films were prepared via the alternate deposition of poly(allylamine hydrochloride) (PAH) and a blend of poly(acrylic acid) (PAA) and poly(styrenesulfonate) (PSS). When the pH of the blend solution was 3.5, the presence of PAA in this solution significantly increased the total film thickness. With only 10 wt % PAA in the blend adsorption solution, a large increase in film thickness was observed (92 nm cf. 18 nm). It was also demonstrated that the total amount of PSS adsorbed was enhanced by the presence of PAA in the blend solution, showing that the blend solution composition influenced that of the multilayer films. Thin films prepared with nanoblended layers also showed improved pH stability, because they exhibited reduced film rearrangement upon exposure to acidic conditions (pH = 2.5).     

Modulation of the functions of osteoblast-like cells on poly(allylamine hydrochloride) and poly(acrylic acid) multilayer films

Deposition of layer-by-layer polyelectrolyte multilayer (PEM) films has been a widely applied surface modification technique to improve the biocompatibility of biomaterials. The objective of this study was to investigate the impact of the deposition of poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) multilayer films on adhesion, growth and differentiation of osteoblasts-like MG63 cells. PAH and PAA were deposited sequentially onto tissue culture polystyrene at either pH 2.0 or pH 6.5 with 4-21 layers. While the MG63 cells attached poorly on the PAH/PAA multilayer films deposited at pH 2.0, while the cells adhered to the PEM films deposited at pH 6.5, depending on layer numbers. Cell adhesion, proliferation and osteogenic activities (alkaline phosphatase activity, expression of osteogenic marker genes and mineralization) were highest on the 4-layer PAH/PAA film and decreased with increasing layer numbers. On the other hand, the behavior of MG63 cells did not show any difference on the adjacent even and odd layers, except PEM4 and PEM5, i.e. the surface charges of the PAH/PAA multilayer films with over ten layers seem indifferent to osteoblastic functions. The results in this study suggested that the mechanical properties of PEM films may play a critical role in modulating the behavior of osteoblasts, providing guidance for application of PEM films to osteopaedic implants.     

Formation of polyelectrolyte multilayers on fibres: influence on wettability and fibre/fibre interaction

Polydimethyldiallylammonium chloride (PDADMAC) and polystyrene sulfonate (PSS) have been used to build-up polyelectrolyte multilayers (PEMs) on chemical soft wood fibres and on SiO2 at various electrolyte concentrations. Adsorption onto SiO2 was studied using a stagnation point adsorption reflectometer (SPAR), and the adsorbed amount of PDADMAC and PSS on the fibres was determined using nitrogen analysis and Sch?niger burning, respectively. The adsorption onto the two substrates was then compared. Paper testing showed that the tensile index (TI) increased by about 90% when 11 layers had been adsorbed, and that there was a correlation between the adsorbed amount and the increase in TI. It was also shown that the particular polymer present in the outermost layer significantly influenced the TI, and that PDADMAC produced a higher TI. A correlation between the adsorbed amount and the TI was also found. Individual fibres were partly treated with a PEM and analysed using a dynamic contact angle analyser (DCA) and environmental scanning electron microscopy (ESEM).     

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.     

Multilayer polyelectrolyte films as nanofiltration membranes for separating monovalent and divalent cations

Alternating adsorption of polyanions and polycations on porous supports provides a convenient way to prepare ion-selective nanofiltration membranes. This work examines optimization of ultrathin, multilayer polyelectrolyte films for monovalent/divalent cation separations relevant to water softening. Membranes composed of five bilayers of poly(styrene sulfonate)/poly(allylamine hydrochloride) (PSS/PAH) on porous alumina supports allow a solution flux of 0.85 m³/(m² day) at 4.8 bar, and exhibit 95% rejection of MgCl₂ along with a Na⁺/Mg²⁺ selectivity of 22. Similar results were obtained in Na⁺/Ca²⁺ separations. PSS/poly(diallyl-dimethylammonium chloride) (PDADMAC) films permit higher fluxes than PSS/PAH systems due to the higher swelling of films containing PDADMAC, but the Mg²⁺ rejection by PSS/PDADMAC membranes is less than 45%. However, capping PSS/PDADMAC films with a bilayer of PSS/PAH yields Mg²⁺ rejections and Na⁺/Mg²⁺ selectivities that are typical of pure PSS/PAH membranes. Separation performance can be optimized through control over deposition conditions (pH and supporting electrolyte concentration) and the charge of the outer layer since Donnan exclusion is a major factor in monovalent/divalent cation selectivity. Streaming potential measurements demonstrate that the magnitude of positive surface charge increases with increasing concentrations of Mg²⁺ in solution or when the outer polycation layer is deposited from a solution of high ionic strength.     

Modulating the structure and properties of poly(sodium 4-styrenesulfonate)/poly(diallyldimethylammonium chloride) multilayers with concentrated salt solutions

Poly(sodium 4-styrenesulfonate) (PSS)/poly(diallyldimethylammonium chloride) (PDADMAC) multilayers were treated with 1-5 M NaCl solutions, resulting in continuous changes in the physicochemical properties of the multilayers. Significant mass loss was observed when the salt concentration was higher than 2 M and reached as high as 72% in a 5 M NaCl solution. The disassembly occurred initially in the superficial layers and then developed in the bulk multilayers. For the multilayers with PDADMAC as the outmost layer, the molar ratio of PSS/PDADMAC was increased and the surface chemistry was changed from PDADMAC domination below 2 M NaCl to PSS domination above 3 M NaCl. Owing to the higher concentrations of uncompensated for polyelectrolytes at both lower and higher salt concentrations, the swelling ratio of the multilayers was decreased until reaching 3 M NaCl and then was increased significantly again. The salt-treated PSS/PDADMAC thin films are expected to show different behaviors in terms of the physical adsorption of various functional substances, cell adhesion and proliferation, and chemical reaction activity.     

Preparation of electrically conducting cellulose fibres utilizing polyelectrolyte multilayers of poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) and poly(allyl amine)

The primary goal with this work is to create electrically conductive cellulose fibres, this has been done to explore possible new applications for fibre based material. This research uses various methods to create polyelectrolyte multilayers (PEMs) on bleached softwood fibres and on SiO₂ model surfaces, by sequentially treating these materials with poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) (PEDOT:PSS) and poly(allyl amine) (PAH). Paper sheets were then produced from the PEM-modified pulp and evaluated in terms of tensile strength, adsorbed amount of polymer, and electrical conductivity. To evaluate the influence of fibre charge on the measured paper properties, pulps of two different initial fibre charge densities were prepared via carboxymethylation. Because of the bluish colour of PEDOT:PSS, the build-up of PEM could be easily followed, since the fibres grew increasingly darker blue throughout the modification sequence. The conductivity of the fibre network increased by 2−3 orders of magnitude when the pulp of a higher fibre charge density was used. This suggests that it is more important to create a fibrous network with a high fibre-fibre joint strength and a large total joined area in the sheet rather than to maximize the adsorbed amount of PEDOT:PSS. A difference in conductivity could also be noted depending on the polyelectrolyte adsorbed in the outer layer, PAH lowered the conductivity compared to PEDOT:PSS. Evaluating the mechanical properties revealed that the use of PEDOT:PSS reduces the tensile strength of the paper. When five double layers had been adsorbed onto the carboxymethylated sample in which PEDOT:PSS formed the outer layer, calculations indicated a 25% decrease in tensile strength compared to that of reference material without PEMs. ESEM studies indicate that PEM treatment produces a significantly changed and somewhat smoother fibre surface.     

Fabrication of ultrathin polyelectrolyte fibers and their controlled release properties

Ultrathin fibers comprising 2-weak polyelectrolytes, poly(acrylic acid) (PAA) and poly(allylamine hydrochloride) (PAH) were fabricated using the electrospinning technique. Methylene blue (MB) was used as a model drug to evaluate the potential application of the fibers for drug delivery. The release of MB was controlled in a nonbuffered medium by changing the pH of the solution. The sustained release of MB in a phosphate buffered saline (PBS) solution was achieved by constructing perfluorosilane networks on the fiber surfaces as capping layers. Temperature controlled release of MB was obtained by depositing temperature sensitive PAA/poly(N-isopropylacrylamide) (PNIPAAM) multilayers onto the fiber surfaces. The controlled release of drugs from electrospun fibers have potential applications as drug carriers in biomedical science.     

Cell adhesion properties of patterned poly(acrylic acid)/poly(allylamine hydrochloride) multilayer films created by room-temperature imprinting technique

Patterned poly(acrylic acid) (PAA)/poly(allylamine hydrochloride) (PAH) multilayer films with line structures of different lateral size and vertical height were fabricated by a room-temperature imprinting technique, and their cell adhesion properties were investigated. The nonimprinted PAA/PAH multilayer films are cytophilic toward NIH/3T3 fibroblasts and HeLa cells whether PAA or PAH is the outer most layer. In contrast, the PAA/PAH multilayer films with a 6.5-microm-line/3.5-microm-space pattern structure are cytophobic toward NIH/3T3 fibroblasts and HeLa cells when the height of the lines is 1.29 microm. By either increasing the lateral size of the patters to 69-microm-line/43-mum-space or decreasing the height of the imprinted lines to approximately 107 nm, imprinted PAA/PAH multilayer films become cytophilic. This kind of transition of cell adhesion behavior derives from the change of the physical pattern size of the PAA/PAH multilayer films and is independent of the chemical composition of the films. The easy patterning of layer-by-layer assembled polymeric multilayer films with the room-temperature imprinting technique provides a facile way to tailor the cellular behavior of the layered polymeric films by simply changing the pattern dimensions.     

Spontaneous wrinkling of layer-by-layer assembled polyelectrolyte films for humidity-responsive superhydrophobicity

The fabrication of smart films with reversible wettability enabled by the stimulus-induced morphology changes has attracted growing interest but remains a challenge. Here we report a smart film that can reversibly changes its wettability between transparent hydrophobicity to translucent superhydrophobicity through the humidity-induced wrinkling/de-wrinkling process. The film was fabricated by depositing hydrophobic SiO₂ nanoparticles (NPs) on poly(acrylic acid) (PAA)/poly(allylamine hydrochloride) (PAH) films, followed by partially exfoliating the films from the underlying substrates. The partially exfoliated PAA/PAH film can reversibly wrinkle and de-wrinkle when being alternately subjected to humid and dry environments. The deposition of hydrophobic SiO₂ NPs on the wrinkling PAA/PAH film does not hinder the humidity-enabled wrin-kling/de-wrinkling ability of the composite film. The hydrophobic SiO₂ NPs and the underlying humidity-wrinkling PAA/PAH film enable the composite film to spontaneously change from hydrophobic and transparent to superhydrophobic and translucent with the rise of environmental humidity.     

Exploring the heteroatom effect on polyelectrolyte multilayer assembly: the neglected polyoniums

Different positive polyelectrolytes having the same charge density, molecular weight, and molecular weight distribution were employed for polyelectrolyte multilayer (PEMU) assembly. The polycations differed only in the heteroatom on which the positive charge resided: poly(vinyl benzyl trimethyl ammonium) chloride, poly(vinyl benzyl trimethyl phosphonium) chloride, and poly(vinyl benzyl dimethyl sulfonium) chloride. While the ammonium repeat unit has been employed on numerous occasions for PEMU assembly, the phosphonium and sulfonium units are relatively neglected. The polyanions, poly(styrene sulfonate), PSS, or poly(acrylic acid), PAA, were typical pH-independent or pH-dependent polymers, respectively. All three polyoniums were quite similar in showing linear layer-by-layer buildup with PSS and exponential growth with PAA, under the conditions employed. Hydration and wettability were also similar between polyoniums.     

Effect of layer integrity of spin self-assembled multilayer films on surface wettability

We investigated the correlation between surface wettability and internal structure of polyelectrolyte (PE)/PE and PE/inorganic multilayer films prepared by the spin self-assembly (SA) method. Spin self-assembled poly(allylamine hydrochloride) (PAH)/poly(sodium 4-styrenesulfonate) (PSS) multilayer films deposited from PE solutions of 10 mM show the distinct oscillation in contact angles with variation of the outermost PE layer, representing the saturated values in contact angles of individual PAH and PSS layers. These contact angles are also well consistent with the angles measured from respective PE layers (i.e., PAH and PSS) of the spin SA (PAH/CdS-COO-) and (CdS-NH3+/PSS) films carrying the flat interface between PE and inorganic CdS nanoparticle layers as confirmed by X-ray reflectivity. Furthermore, based on the contact angle of CdS-NH3+ layer in the ordered (CdS-NH3+/PSS) films, the change in surface wettability of CdS-NH3+ layers of two different spin SA (CdS-NH3+/poly(methacrylic acid) (PMAA)) multilayer films with ordered and disordered internal structure is also investigated. The films with ordered and disordered internal structure were fabricated by the pH adjustment of PMAA. The CdS-NH3+ layer in both CdS-NH3+/PSS and CdS-NH3+/PMAA multilayer films with the ordered internal structure has the contact angle of about 25 +/- 2 degrees irrespective of the PSS or PMAA sublayer. As a result, the same surface wettability of PE or inorganic layers, despite different sublayers, strongly indicates that the spin SA method in optimum condition allows the top surface to be completely covered with a low level ofinterdigitation with a sublayer at each deposition step, and this leads to the conclusion that physical and chemical characteristics of the sublayers have no significant influence on those of the outermost layer.     

Controlling the nanofiltration properties of multilayer polyelectrolyte membranes through variation of film composition

We report the use of a variety of polyelectrolyte multilayers (PEMs) as selective skins in composite membranes for nanofiltration (NF) and diffusion dialysis. Deposition of PEMs occurs through simple alternating adsorption of polycations and polyanions, and separations can be optimized by varying the constituent polyelectrolytes as well as deposition conditions. In general, the use of polycations and polyanions with lower charge densities allows separation of larger analytes. Depending on the polyelectrolytes employed, PEM membranes can remove salt from sugar solutions, separate proteins, or allow size-selective passage of specific sugars. Additionally, because of the minimal thickness of PEMs, NF pure water fluxes through these membranes typically range from 1.5 to 3 m3/(m2 day) at 4.8 bar. Specifically, to separate sugars, we employed poly(styrene sulfonate) (PSS)/poly(diallyldimethylammonium chloride) (PDADMAC) films, which allow 42% passage of glucose along with a 98% rejection of raffinose and a pure water flux of 2.4 m3/(m2 day). PSS/PDADMAC membranes are also capable of separating NaCl and sucrose (selectivity of approximately 10), while high-flux chitosan/hyaluronic acid membranes [pure water flux of 5 m3/(m2 day) at 4.8 bar] may prove useful in protein separations.     

Influence of polyelectrolyte multilayer adsorption on the temperature sensitivity of poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) (PNiPAM) microgels

The electrophoretic mobility and temperature-dependent particle size of poly(N-isopropylacrylamide) (PNiPAM) microgels after alternating adsorption of poly(diallyldimethylammonium chloride) (PDADMAC) and poly(sodium 4-styrenesulfonate) (PSS) have been determined. First a PNiPAM-co-acrylic acid (AAc) shell was added to the PNiPAM microgel, then PDADMAC and PSS were adsorbed alternately. The studies of the electrophoretic mobility revealed charge reversal when a polyelectrolyte (PE) layer was adsorbed. Particle size measurements revealed a strong influence of polyelectrolyte adsorption on the temperature-dependent particle swelling. The strong influence of the adsorbed polyelectrolyte on the particle size is in contrast to polyelectrolyte multilayer adsorption on rigid particles.     

Fibronectin adsorption onto polyelectrolyte multilayer films

The Layer-by-layer deposition of positively and negatively charged macromolecular species is an ideal method for constructing thin films incorporating biological molecules. We investigate the adsorption of fibronectin onto polyelectrolyte multilayer (PEM) films using optical waveguide lightmode spectroscopy (OWLS) and atomic force microscopy (AFM). PEM films are formed by adsorption onto Si(Ti)O2 from alternately introduced flowing solutions of anionic poly(sodium 4-styrenesulfonate) (PSS) and cationic poly(allylamine hydrochloride) (PAH). Using OWLS, we find the initial rate and overall extent offibronectin adsorption to be greatest on PEM films terminated with a PAH layer. The polarizability density of the adsorbed protein layer, as measured by its refractive index, is virtually identical on both PAH- and PSS-terminated films; the higher adsorbed density on the PAH-terminated film is due to an adsorbed layer of roughly twice the thickness. The binding of monoclonal antibodies specific to the protein's cell binding site is considerably enhanced to fibronectin adsorbed to the PSS layer, indicating a more accessible adsorbed layer. With increased salt concentration, we find thicker PEM films but considerably thinner adsorbed fibronectin layers, owing to increased electrostatic screening. Using AFM, we find adsorbed fibronectin layers to contain clusters; these are more numerous and symmetric on the PSS-terminated film. By considering the electrostatic binding of a segmental model fibronectin molecule, we propose a picture of fibronectin adsorbed primarily in an end-on-oriented monolayer on a PAH-terminated film and as clusters plus side-on-oriented isolated molecules onto a PSS-terminated film.     

Preparation and characterization of polyelectrolyte-coated gold nanoparticles

Gold nanoparticles of 5 nm diameter, stabilized by 4-(dimethylamino)pyridine (DMAP), were coated with poly(sodium 4-styrene sulfonate) (PSS) via electrostatic self-assembly. The suspension stability, monitored by the gold surface plasmon band (SPB), was studied by varying the pH, the PSS chain length, and PSS concentration. Enhanced stability is obtained at pH 10 (above the pKa of DMAP) when the polymer chain length matches or exceeds the particle circumference. Solid state 13C NMR was used to determine the presence of DMAP and polymers after subsequent deposition of weak and strong polycations: poly(allylamine hydrochloride) (PAH) and poly(diallyldimethylammonium chloride) (PDADMAC). At pH 10, DMAP remains associated with the nanoparticle after the first PSS layer has been formed. When PAH or PDADMAC are subsequently added at pH 4.5, DMAP is expelled, the suspensions remain stable, and zeta potential values indicate complete charge reversal. In the case of PDADMAC, however, the first layer of PSS is not fully retained. When PDADMAC is added at pH 10, DMAP and the first PSS layer are retained but lower zeta potentials and a higher SPB shift indicate a degraded stability. For PAH addition at pH 9.5, both DMAP and PSS are expelled and the suspension becomes unstable. These differences in stability of the multilayer components and the nanoparticle suspension are rationalized in terms of chain flexibility, polymer charge density, and the ability of the polymer functional groups to directly interact with the gold surface.