Measurement of elastic nonlinearity using remote laser ultrasonics and CHeap Optical Transducers and dual frequency surface acoustic waves

A nonlinear ultrasonic technique for evaluating material elastic nonlinearity has been developed. It measures the phase modulation of a high frequency (82MHz) surface acoustic wave interacting with a low frequency (1MHz) high amplitude stress inducing surface acoustic wave. A new breed of optical transducers has been developed and used for the generation and detection of the high frequency wave. The CHeap Optical Transducer (CHOT) is an ultrasonic transducer system, optically activated and read by a laser. We show that CHOTs offer advantages over alternative transducers. CHOTs and nonlinear ultrasonics have great potential for aerospace applications. Results measuring changes in ultrasonic velocity corresponding to different stress states of the sample are presented on fused silica and aluminium.     

水下声辐射激励水表面声波的特征参数测量

采用激光干涉方法对水下声辐射激励水表面声波的特征参数频率和振幅进行了测量研究。从理论上对水表面声波激光相干测量信号的频谱构成进行了分析,在此基础上提出了水表面声波两个重要声学参数频率和振幅的解算方法,并通过数值仿真进行了验证。搭建了一套简单的激光干涉测量实验系统,对不同频率和声压激励的水表面声波进行了测量实验,验证了水表面声波频率和振幅解调方法的准确性。对水表面声波横向传播的振幅衰减现象进行了初步的实验研究,结果表明水表面声波的频率越高,振幅的横向衰减越快。研究表明激光相干检测方法能够准确地实现水表面声波振幅和频率的测量。      

基于AlN声表面波滤波传感器器件的有限元仿真

声表面波器件是一种利用压电材料的压电效应与逆压电效应工作电子器件, 文章首先详细描述了声表面波器件的设计与仿真过程,运用有限元分析的方法分别计算了利用声表面波的 SAW 器件与利用体波的 BAW 器件的性能与各项参数,对相关的器件进行了计算分析,分别用上述方法研究了基于 AlN 薄膜的声表面波器件和悬臂梁结构的体波器件,推导得出了器件的电学导纳与频率之间的关系, 通过分析器件的导纳-频率曲线,推导出器件内部声波的模式以及合适的工作频率,最终得出在 IDT 周期为 8 微米的情况下,SAW 器件的理想工作频率是 0.7-1.95GHz,BAW 器件的理想工作频率在 0.6-3.2GHz 的结果。     

基于密集波分复用技术的Bragg光栅水听器

论述了用Bragg光栅制作水听器的原理和意义,利用光纤通信的密集波分技术,实现声压信号动态解调.采用压力增敏材料对Bragg光栅封装来增加其响应灵敏度,为避免温度变化引起光栅交叉敏感,在室温23±1℃条件下进行试验,给出实验结果.实验表明:基元水听器的频率响应平坦度好,信号输出稳定.同时采用密集波分技术动态解调声信号方案是可行的.     

Acoustic properties of multiferroic BiFeO<Subscript>3</Subscript> over the temperature range 4.2–830 K

The longitudinal acoustic wave velocity and attenuation in BiFeO₃ ceramics have been measured by ultrasonic pulse-echo technique at a frequency of 10 MHz in the temperature range from 4.2 K to 830 K. The anomalies observed in the sound velocity and attenuation behavior versus temperature are attributed to the assumed relaxation in the temperature range 200–500 K and antiferromagnetic phase transition at higher temperatures. Order parameter fluctuations along with magnetostriction are discussed as the factors determining the acoustic wave velocity anomaly in the vicinity of the antiferromagnetic phase transition point.     

水声信号处理领域新进展

本文介绍近30年来水声信号处理领域理论研究的新进展和在声纳设计中的应用。包括水声信号建模、声场匹配、海洋波导和内波现象的探索和研究、声矢量场信息获取和处理,低频水声信道的时/空相关特性,水下目标辐射噪声的不变特征量提取和检测技术,水下语音、图像传输和抗干扰技术。同时概述,声纳设计的前沿领域:大孔径拖曳线列阵声纳、高分辨力合成孔径声纳、深海传呼机等的发展情况。     

Experimental study of propagation of instability waves in a submerged jet under transverse acoustic excitation

An experimental study was conducted on the specific features of instability wave propagation in the mixing layer of a turbulent jet when the jet is excited by an external acoustic wave. We used the technique of conditional phase averaging of data obtained by particle image velocimetry using the reference signal of a microphone placed near the jet. The influence of the excitation frequency on the characteristics of large-scale structures in the mixing layer was investigated. It is shown that the propagation patterns of the instability waves agree well with previously obtained data on the localization of acoustic sources in turbulent jets.     

Prediction of the sound field above a patchwork of absorbing materials

The aim of this paper is to investigate the acoustic performance of sound absorbing materials through a numerical wave based prediction technique. The final goal of this work is to get insight into the acoustic behavior of a combination of sound absorbing patches. In order to address a wide frequency range, a model based on the Trefftz approach is adopted. In this approach, the dynamic field variables are expressed in terms of global wave function expansions that satisfy the governing dynamic equations exactly. Therefore, approximation errors are associated only with the boundary conditions of the considered problem. This results in a computationally efficient technique. The main advantage of this method is the fact that the sound absorbing patches do not have to be locally reacting. In this article, the wave based method is described and experimentally validated for the case of normal incidence sound absorption identification in a standing wave tube. Afterwards, the method is applied to simulate some interesting setups of absorbing materials.     

Study of thermoviscous dissipation on axisymmetric wave propagating in a shear pipeline flow confined by rigid wall. Part II. Numerical study

Axisymmetric acoustic wave propagating in a shear pipeline flow confined by a rigid wall is studied in the two-part paper. The effects of viscous friction and thermal conduction on the acoustic wave propagating in the liquid and perfect gas are respectively analyzed under different configurations of acoustic frequency and shear mean flow. In Part 2 of this paper, comprehensive analysis of the effects of shear mean flow and acoustic frequency on the features (relative phase velocity and attenuation coefficient) of the acoustic wave are numerically addressed in cases of water and perfect gas respectively. Comparisons between the non-isentropic and isentropic models are provided in details. Meanwhile, discussions of the thermoviscous effects on the acoustic wave between water and perfect gas are given.     

Acoustooptic multiplication of the frequency shift of optical radiation on the basis of bragg polarization splitting

A technique for the acoustooptic multiplication of the frequency shift of an optical beam is proposed. The technique is based on the cascade diffraction of the beam by a single acoustic wave with the use of Bragg polarization splitting in a uniaxial crystal. The fundamental possibility of the practical realization of the technique is confirmed experimentally by using anisotropic acoustooptic diffraction in LiNbO₃.     

New visualization method of progressive acoustic wavefronts using a Köster prism

Visualization of a progressive acoustic wave is explained and verified experimentally. A Köster prism set in an image-forming system works so that the optical wave fields emerging from two points across the exit plane of an acoustic column may be superposed at a point in the image plane. The image intensity changes with a period of half the acoustic wavelength magnified suitably. The visibility of the image intensity takes values between 0 and 0.54 if the acoustic power is made to change. No practical frequency limitation is present in the lower frequency range of the acoustic wave.     

Acousto-optical spectrum analysis of ultra-high-frequency radio-wave analogue signals with an improved resolution exploiting the collinear acoustic wave heterodyning

This article is devoted to the problem of improving the frequency resolution inherent in a parallel acousto-optical spectrum analysis via involving an additional nonlinear phenomenon into the data processing. In so doing, we examine possible application of the wave heterodyning to the real-time scale acousto-optical analysis of the frequency spectrum belonging to ultra-high-frequency radio-wave signals peculiar, for example, for radio-astronomy. The nonlinear process of wave heterodyning is realized through providing a co-directional collinear interaction of the longitudinal acoustic waves of finite amplitudes. This process, which is beforehand studied theoretically and investigated experimentally via the acousto-optical technique as well, allows us either to improve the frequency resolution of spectrum analysis at a given frequency range or to increase by a few times the current frequencies of radio-wave signals under processing. The first step along this way is connected with the experimental modeling of the acoustic wave heterodyning in solids via exploitation of the specific acousto-optical cell based on a liquid, which allows the simplest realization of a cell with the needed properties. Then, these theoretical and practical findings are used in our experimental studies aimed at creating a new type of acousto-optical cells, which are able to improve the resolution inherent in acousto-optical spectrum analyzer operating over ultra-high-frequency radio-wave signals. In particular, the possibility of upgrading the frequency resolution through the acoustic wave heterodyning is experimentally demonstrated using the cell made of lead molybdate crystal. The obtained results demonstrate practical efficiency of the novel approach presented.     

大气风场和温度对无线电声波探测系统探测高度影响的数值研究

从声波扰动介质中的电波波动方程出发, 使用时域有限差分(FDTD)方法, 结合声波传播的FDTD 模型, 构建了描述声波和电波相互作用的数值模型, 并运用该模型分析风场和温度对无线电声波探测系统的探测高度的影响. 数值模拟结果表明: 温度与风场剖面的存在改变声波和电波散射回波的传播轨迹; 温度梯度剖面主要影响声波的传播速度, 风场剖面导致作为电波散射体的声波波阵面的偏移, 降低电波散射回波的强度并改变回波路径, 使得接收数据减少, 限制无线电声波探测系统的探测高度; 在强风背景下, 若降低声波散射体高度, 电波散射回波“聚束点”的偏移会有较大的改善, 但同时意味着探测高度的降低. 为了改善风场背景下无线电声波探测系统的探测高度, 可以使用双基地雷达或者增大接收天线面积等方法来实现.     

A semi-automatic processing technique for elastic-wave laboratory data

This paper addresses the problem of determining the onset of transient signals such as seismograms, acoustic emissions or ultrasonic signals. Usual manual techniques of onset-time picking are time consuming when numerous measurements are available. This may occur when dealing with (i) anisotropic rocks requiring many elastic wave velocities measurements in the laboratory, (ii) 4-D seismic field data or (iii) laboratory acoustic emissions data. We present a semi-automatic processing technique devoted to the study of case (i). It is based on ultrasonic signal analysis by wavelet transform and an onset-time picking procedure combining Akaike Information Criterion and cross-correlation method. The first step consists in extracting, from the whole experimentally recorded signal, the frequency component corresponding to the perturbation induced by a typical ultrasonic transducer in the laboratory. The second step is dedicated to the onset-time picking of the phase arrival in the extracted signal. The use of this processing technique based on mathematical arguments reduces human subjectivity. Main outcomes are: (i) increase of signal-to-noise ratio; (ii) measurement of elastic wave velocities at prescribed central frequency; (iii) drastic increase of efficiency in wave data processing; and (iv) increase in reliability (repeatability) of wave data acquisition.     

Acoustic Imaging Frequency Dynamics of Ferroelectric Domains by Atomic Force Microscopy

We report the acoustic imaging frequency dynamics of ferroelectric domains by low-frequency acoustic probe microscopy based on the commercial atomic force microscopy. It is found that ferroelectric domain could be firstly visualized at lower frequency down to 0.5 kHz by AFM-based acoustic microscopy. The frequency-dependent acoustic signal revealed a strong acoustic response in the frequency range from 7kHz to 10 kHz, and reached maximum at 8.1 kHz. The acoustic contrast mechanism can be ascribed to the different elastic response of ferroelectric microstructures to local elastic stress fields, which is induced by the acoustic wave transmitting in the sample when the piezoelectric transducer is vibrating and exciting acoustic wave under ac electric fields due to normal piezoelectric effects.     

Proper Generalized Decomposition applied to linear acoustic: A new tool for broad band calculation

The calculation of the acoustic response of systems in frequency bands is becoming increasingly important in simulation-based engineering design. This is particularly true in medium-frequency bands, where the response is very sensitive to the frequency. Some standard techniques for addressing these problems present a frequency dependent formulation and may involve fixed-frequency calculations at many different frequencies. In this paper, we propose a new technique which combines the Variational Theory of Complex Rays (VTCR) with Proper Generalized Decomposition (PGD) and does not require the resolution of acoustic problems at many frequencies. In this approach, the VTCR is used to find an approximate solution of a medium-frequency acoustic problem using only a few degrees of freedom (DOFs). Then, PGD is used to find a representation of the approximate solution which is separated between two variables, the wave propagation direction and the frequency. A relevant numerical example is used to present the strategy and illustrate its applicability for frequency band calculations.     

Laser generation of surface acoustic modes guided by copper lines of sub-micron width on silicon

Surface acoustic waves guided by a copper line embedded in a silica film on a silicon wafer were generated and detected optically using the laser-induced transient grating technique. Lines as narrow as ∼0.2 μm yield a good signal despite the much larger size of the laser spot. The phase velocity of the guided mode is slightly lower than the surface acoustic wave velocity in the thin film structure. Good correlation between the acoustic frequency and the electrical resistivity of the copper lines results from the dependence of both measurements on the line width.     

Combining Brillouin spectroscopy and laser-SAW technique for elastic property characterization of thick DLC films

Surface Brillouin spectroscopy (SBS) has been widely used for elastic property characterization of thin films. For films thicker than 500 nm, however, the wavelength of surface acoustic wave in the frequency range available for SBS is smaller than film thickness, and the SBS measures only the Rayleigh wave of the film. The laser-SAW technique, on the other hand, measures only the low-frequency portion of the surface acoustic wave dispersion and can estimate only one elastic modulus of the film (typically Young's modulus). In this work, we have combined the two methods to determine both Young's modulus and Poisson's ratio of a diamond-like carbon (DLC) film. It was found that reasonable estimates can be obtained for the longitudinal wave velocity, shear wave velocity, and Young's modulus of the film. The Poisson's ratio, however, still has a relatively large measurement error.     

Acoustic impulse response method as a source of undergraduate research projects and advanced laboratory experiments

A straightforward and inexpensive implementation of acoustic impulse response measurement is described utilizing the signal processing technique of coherent averaging. The technique is capable of high signal-to-noise measurements with personal computer data acquisition equipment, an amplifier/speaker, and a high quality microphone. When coupled with simple waveguide test systems fabricated from commercial PVC plumbing pipe, impulse response measurement has proven to be ideal for undergraduate research projects-often of publishable quality-or for advanced laboratory experiments. The technique provides important learning objectives for science or engineering students in areas such as interfacing and computer control of experiments; analog-to-digital conversion and sampling; time and frequency analysis using Fourier transforms; signal processing; and insight into a variety of current research areas such as acoustic bandgap materials, acoustic metamaterials, and fast and slow wave manipulation.     

Excitation of ion acoustic waves at the difference frequency of two microwave beams in a semiconductor

This letter presents an investigation of the resonant excitation of the electrostatic ion acoustic wave at the difference frequency of two microwave beams in a semiconductor, viz., n-type InSb. The ponderomotive force at the difference frequency on electrons drives the ion acoustic wave at the difference frequency. The resonance conditions are satisfied over a wide range of semiconductor parameters. For typical plasma parameters of n-InSb and microwave beams of power densities 1 MW cm^?2, the power density of the excited ion acoustic wave is ≈ 1.76 kW cm^?2.