含稀土钛系催化剂的苯乙烯高活性定向聚合研究

本文用新研制的含稀土钕化合物的钛系催化剂(SN-1催化剂)于苯乙烯在苯溶液中进行定向聚合,能同时使产率、等规度、催化效率与聚合速率四项指标得到提高并远超过文献值。研究了各种聚合条件,即催化剂浓度、苯乙烯单体浓度、助催化剂三乙基铝浓度和聚合温度各因素对于催化效率、聚苯乙烯产率、等规度和分子量的影响规律并作讨论。     

Ethylene polymerization with porous polystyrene spheres supported Cp2ZrCl2 catalyst

A catalyst with porous polystyrene beads supported Cp₂ZrCl₂ was prepared and tested for ethylene polymerization with methylaluminoxane as a cocatalyst. By comparison, the porous supported catalyst maintained higher activity and produced polyethylene with better morphology than its corresponding solid supported catalyst. The differences between activities of the catalysts and morphologies of the products were reasonably explained by the fragmentation processes of support as frequently observed with the inorganic supported Ziegler–Natta catalysts. Investigation into the distribution of polystyrene in the polyethylene revealed the fact that the porous polystyrene supported catalyst had undergone fragmentation during polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3313–3319, 2003     

Synthesis of isotactic polystyrene with a rare-earth catalyst

Polymerization of styrene with the neodymium phosphonate Nd(P₅₀₇)/H₂O/Al(i-Bu)₃ catalytic system has been examined. The polymer obtained was separated into a soluble and an insoluble fraction by 2-butanone extraction. ¹³C-NMR spectra indicate that the insoluble fraction is isotactic polystyrene and the soluble one is syndiotactic-rich atactic polystyrene. The polymerization features are described and discussed. The optimum conditions for the polymerization are as follows: [Nd] = (3.5–5.0) × 10⁻² mol/L; [styrene] = 5 mol/L; [Al]/[Nd] = 6–8 mol/mol; [H₂O]/[Al] = 0.05–0.08 mol/mol; polymerization temperature around 70°C. The percent yield of isotactic polystyrene (IY) is markedly affected by catalyst aging temperature. With increase of the aging temperature from 40 to 70°C, IY increases from 9% to 48%. Using AlEt₃ and Al(i-Bu)₂H instead of Al(i-Bu)₃ decreases the yield of isotactic polystyrene. Different neodymium compounds give the following activity order: Nd(P₅₀₇)₃ > Nd(P₂₀₄)₃ > Nd(OPrⁱ)₃ > NdCl₃ + C₂H₅OH > Nd(naph)₃. With Nd(naph)₃ as catalyst, only atactic polystyrene is obtained. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1773–1778, 1998     

Comparison of Syndiotactic Polystyrene Morphology Obtained Via Heterogeneous and Homogeneous Polymerization with Metallocene Catalyst

Summary: Supported catalyst system for the slurry phase polymerization of styrene in toluene was prepared by the immobilization of 2-methylindenyltrichlorotitanium(2-MeIndTiCl₃) on silica and activation of this catalyst was performed by methylaluminoxane(MAO) in polymerization media. Homogeneous polymerization of styrene with 2-methylindenyltrichlorotitanium activated by MAO was performed in toluene. The morphology of obtained syndiotactic polystyrene (sPS) via heterogeneous and homhgeneous catalyst system was compared. Polymerization of styrene by homogeneous catalyst lead to formation of gel and resultant polymers presented a compact and dense texture while the global gelation do not occur with silica supported catalyst at different Ti/SiO₂ mol ratios and sPS was obtained as separated particles. Unlike to the homogeneous catalyst, obtained polymers showed a porous texture. Highly porous texture of sPS was obtained with Ti/SiO₂ = 0.5% mol ratio.     

Homopolymerization of ω‐Styryl‐Polystyrene Macromonomers in the Presence of CpTiF3/MAO

Summary: ω‐Styryl‐polystyrene macromonomers were synthesized by anionic induced deactivation reactions. Their homopolymerization in the presence of a fluorinated half‐sandwich metallocene catalyst (CpTiF₃/MAO) was investigated. In spite of the intrinsic lower reactivity of these macromonomers with respect to the micromolecular monomer, coordination homopolymerization was possible. The influence of several experimental parameters on the polymerization yield and degree could be demonstrated. In most cases, under identical experimental conditions, higher polymerization yields and degrees were observed with respect to the CpTiCl₃/MAO catalyst.

The synthesis of p‐polystyryl‐substituted styrene derivatives by the homopolymerization of ω‐styryl‐polystyrene macromonomers in the presence of CpTiF₃.     

Polymer-supported Ziegler–Natta catalyst for the polymerization of isoprene

A polymer-supported Ziegler–Natta catalyst, polystyrene-TiCl₄AlEt₂Cl (PS–TiCl₄AlEt₂Cl), was synthesized by reaction of polystyrene–TiCl₄ complex (PS–TiCl₄) with AlEt₂Cl. This catalyst showed the same, or lightly greater catalytic activity to the unsupported Ziegler–Natta catalyst for polymerization of isoprene. It also has much greater storability, and can be reused and regenerated. Its overall catalytic yield for isoprene polymerization is ca. 20 kg polyisoprene/gTi. The polymerization rate depends on catalyst titanium concentration, mole ratio of Al/Ti, monomer concentration, and temperature. The kinetic equation of this polymerization is: R_p = k[M]^0.30[Ti]^0.41[Al]^1.28, and the apparent activation energy ΔE_act = 14.5 kJ/Mol, and the frequency factor A_p = 33 L/(mol s). The mechanism of the isoprene polymerization catalyzed by the polymer-supported catalyst is also described. © 1993 John Wiley & Sons, Inc.     

New Materials Designed by Coordination Polymerization of ω-undecenyl Macromonomers

The major part of the present paper discusses the ability of well-defined ω-undecenyl polystyrene, polyisoprene or poly(styrene-block-isoprene) macromonomers to undergo coordination homopolymerization in the presence of selected titanium catalysts. Special emphasis is given to the influence of the nature of the catalyst, the polymerization temperature and the macromonomer molar mass and concentration on homopolymerization yield and average degree of homopolymerization (DP_n). Titanium-based catalytic systems such as CpTiCl₃/MAO and Cp*TiCl₃/MAO only yielded dimers. The use of the homogeneous metallocene catalyst with constrained ligand geometry (CGC-Ti/MAO) having an open active site, significantly improved the degree of polymerization. Increasing macromonomer molar mass, causes only a slight decrease of DP_n whereas conversion increased moderately. The final section briefly discusses the copolymerization of ω-undecenyl polystyrene macromonomers with ethylene in the presence of Versipol™ catalysts.     

New neutral Ni(II)- and Pd(II)-based initiators for polymerization of styrene

Neutral nickel and palladium σ-acetylide complexes [Ni(CCPh)₂(PBu₃)₂] and [Pd(CCPh)₂(PBu₃)₂] are novel initiators for the polymerization of styrene in CHCl₃ over a range of polymerization temperature from 40 to 60 °C. Between them, the nickel catalyst exhibited much higher activity than the palladium catalyst. The polystyrene obtained with Ni(II) initiator was a syndio-rich atactic polymer and its weight-average molecular weight reached 279 000. The mechanism of the polymerization was discussed and a radical mechanism was proposed.     

Syntheses and properties of syndiotactic polystyrene

Syndiotactic polystyrene (SPS) is a new crystalline engineering thermoplastic. With a melting point of 270 °C and its crystalline nature, SPS has high heat resistance, excellent chemical resistance and water/steam resistance. Since SPS has excellent dielectric properties, it is useful as a capacitor insulation material. The rate of crystallization is very fast in comparison with isotactic polystyrene (IPS), thus, SPS can be used in a number of forming operations, including injection molding, extrusion and thermoforming. A system composed of a homogeneous titanium compound and methylaluminoxane (MAO) is an effective catalyst for syndiospecific polymerization of styrene. On the other hand heterogeneous titanium compounds containing halogen make a mixture of isotactic and syndiotactic components. The amount of syndiotactic polystyrene obtained is dependent on the mole ratio of Al to Ti. The result of ESR measurement suggests the Ti³⁺ species are important as a highly active site for producing syndiotactic polystyrene. A comparison of the stereoregularities of polypropylene and polystyrene formed by various metallocene catalysts is studied. The (C₆H₆)₂C(η₅-C₅H₄)(η₅-C₉H₆)TiCl₂/MAO system gives a homogeneous catalyst for the polymerization of propylene giving isotactic rich polypropylene and of styrene to give syndiotactic polystyrene.     

Synthesis of polystyrene with high melting temperature through BDE/CuCl catalyzed polymerization

No matter what the polymerization manner was, polystyrene with unique highT _m (T _m = 170–285°C) was obtained through polymerization of styrene if the amount of BDE/CuCl catalyst was highly increased (mol ratio: St:CuCl = 25:1-2.5:1). Partial crystallinity of the PSt was observed by characterizations of X-ray diffraction and DSC. Spectra of¹H-NMR and¹³C-NMR showed that syndiotactic structure contained in the obtained PSt was 5% more than that in aPSt (atactic polystyrene). According to the proposed “coordinated radical cage” mechanism, the coordinated state between radical and catalyst center metal Cu should be more closely packed with increasing the BDE/CuCl catalyst amount, which was induced to partial stereospecific polymerization in the coordinated radical polymerization of St.     

Study of the chain transfer reaction by hydrogen in the initial stage of propene polymerization

The chain transfer reaction by hydrogen in the initial stage of propene polymerization with MgCl₂-supported Ziegler catalyst was studied by means of the stopped-flow polymerization. The yield and molecular weight of polypropene produced in the initial stage were not affected by hydrogen. Thus, the method was successfully applied to find the region in which hydrogen does not act as a chain transfer reagent. On the other hand, a chain transfer reaction proceeded in the initial stage of polymerization by using Zn(C₂H₅)₂. Furthermore, when the catalyst was treated with Al(C₂H₅)₃ before polymerization, the molecular weight of the produced polymer was decreased by using hydrogen, indicating that it acted as a chain transfer agent for the catalyst modified by pre-treatment.     

Stereoregularity of polystyrene-β,β-d2

The 100-MHz methine proton spectra of polystyrene-β,β-d₂ obtained by radical and cationic initiators consisted of four peaks at 2.35, 2.25, 2.17, and 2.03 ppm, the proportion of which changed with polymerization conditions such as catalyst, solvent, and temperature. The spectrum was interpreted in terms of pentad sequences assuming Bernoullian statistics and the stereoregularity was determined. Polystyrene-β,β-d₂ prepared by radical initiators had a syndiotactic-rich configuration, independent of polymerization temperature. Polymers obtained by cationic initiators had lower racemic dyads. Cationic polymerization in toluene at 0°C gave a polymer of an almost random configuration. It was revealed that nondeuterated polystyrene of a random configuration can be distinguished from syndiotactic-rich polystyrene as well as the isotactic polymer by 100 MHz NMR spectroscopy.     

Syndiospecific polymerization of styrene. I. Tetrabenzyl titanium/methylaluminoxane catalyst

Syndiospecific polymerization of styrene (S) was catalyzed by Bz₄Ti/MAO (tetrabenzyltitanium/methylaluminoxane). The product was separated into syndiotactic polystyrene (s-PS) and atactic polystyrene (a-PS) by extraction of the latter with boiling 2-butanone. Over the broad range of catalyst concentrations, compositions, and polymerization temperatures, the catalytic activity is 150 ± 80kg PS (mol Ti mo S h)^?1 with 89 ± 5% yield of s-PS (SY). The concentration of active species has been determined by radiolabeling. Only about 1.7% of Bz₄Ti initiates syndiospecific polymerization at 60°C with values of rate constants for propagation and for chain transfer to MAO of 1.38 (M s)^?1 and 5.2 × 10^?4s^?1, respectively. Nonspecific polymerization was initiated by 16.8% of the Ti having values of 0.056 (M s)^?1 and 6.5 × 10^?4 s^?1 for the rate constants of propagation and transfer, respectively. The effect of solvent polarity on the polymerization was studied using toluene mixed with chlorobenzene of o-dichlorobenzene as solvents. An increase of effective dielectric constant from 2.43 to 5.92 reduces the polymerization activity by a factor of two and lowers SY to mere 39%. In 1 : 1 toluene/chlorobenzene solvent mixture, it was found that 1.3% and 26% of the Bz₄Ti initiate syndiospecific and nonspecific polymerizations of styrene, respectively. The Bz₄Ti/MAO catalyst is poor in both productivity and stereoselectivity.     

阻聚剂对MMA原子转移自由基聚合的影响

Effect of a series of inhibitors as additives on atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) with FeCl2/PPh3 as catalyst system was studied, including 2,4,6-trinitrophenol (TNP), 4-methoxyphenol (4-MP), hydroquinone (HQ) and nitrobenzene (NB). It was found that TNP was the only. efficient additive for ATRP among these inhibitors. In the presence of small amounts of TNP, the polymerization proceeded rapidly after induction period to yield the polymers with controlled molecular weights and narrow molecular weight distributions (MWD). The initiating efficiency of the modified catalyst system with TNP was increased. The mechanism was proposed and confirmed by the end group analysis of the polymer.     

Synthesis and characterization of comb-like polyphenylenes via Suzuki coupling of polystyrene macromonomers prepared by atom transfer radical polymerization

1,4-Dibromo-2,5-bis(bromomethyl)benzene was used as initiator in atom transfer radical polymerization of styrene in conjunction with CuBr/2,2^′-bipyridine as catalyst. The resulting macromonomer, with a central 2,5 dibromobenzene ring and the degree of polymerization of 16 at each side, was used in combination with 2,5-dihexylbenzene-1,4-diboronic acid, for a Suzuki coupling in the presence of Pd(PPh₃)₄ as catalyst. The obtained polyphenylene, with alternating polystyrene and hexyl side chains, has high solubility in common organic solvents at room temperature. The new polymer was characterized by GPC, 1H-NMR, 13C-NMR, IR and UV analysis. Thermal behavior of the precursor polystyrene macromonomer and the final polyphenylene was investigated by thermogravimetric analysis and differential scanning calorimeter/calorimetry analyses and compared.     

Preparation of two kinds of chloromethylated polystyrene particle using 1,4-bis (chloromethoxy) butane as chloromethylation reagent

By adopting “grafting from” manner, polystyrene was grafted onto the surface of silica gel particles with an average size of 125 μm in a solution polymerization system, and grafted particle PSt/SiO₂ was prepared. Using 1,4-bis (chloromethoxy) butane (BCMB, it is nontoxic.) as chloromethylation reagent, chloromethylation reaction for the grafted particle PSt/SiO₂ was performed in the presence of Lewis acid catalyst SnCl₄. At the same time, cross-linked styrene-divinylbenzene copolymer (CPS) microsphere also was chloromethylated with the same reagent as PSt/SiO₂, so that two kinds of chloromethylated polystyrene particles were obtained, and they are chloromethylated grafted particle (CMPS/SiO₂) and chloromethylated cross-linked polystyrene (CMCPS) microsphere, respectively. The chemical structures and compositions of the two particles were characterized using Fourier transform infrared and Volhard method. The effects of various factors on the chloromethylation reactions were mainly investigated. The experimental results show that the process to prepare the two kinds of chloromethylated polystyrene particles not only has the character of environment friendness and low cost but also is convenient to control via adjusting various reaction conditions. The main reaction conditions affecting the chloromethylation reactions are reaction time, the added amount of BCMB, and the used amount of solvent and catalyst. They influence the reaction in two respects: (1) the chloromethylation degrees of polystyrene are different under different conditions; (2) Friedel–Crafts cross-linking reaction between polystyrene macromolecules is accelerated or inhibited under different conditions (for CPS microsphere, this cross-linking reaction also is called the additional cross-linking). Under suitable conditions, the two kinds of chloromethylated polystyrene particles with a high chlorine content (about 17%, this chlorine content was calculated based on polystyrene weight) can be gained using SnCl₄ as catalyst and CH₂Cl₂ as solvent at room temperature for 10 h and basically without cross-linking or additional cross-linking.     

Ethene polymerization with modified-polypropene-supported highly stable Ziegler catalyst

A modified-polypropene-supported Ziegler catalyst was prepared using polypropene containing a small amount of poly(7-methyl-1,6-octadiene) as a starting polymer for bromination, lithiation, and reaction with TiCl₄. The polymerization of ethene was carried out using the catalyst with Al(C₂H₅)₃ in toluene at 60°C up to 100 h. The polymer yield increased linearly with polymerization time, which indicates that the active sites of the modified-polypropene-supported Ziegler catalyst are practically stable without deactivation even for 100 h and are able to propagate further polymerization of ethene.     

Anionic polymerization of methyl methacrylate with Cr(C5H7O2)3–Al(C2H5)3 catalyst system

A homogeneous catalyst system, Cr(C₅H₇O₂)₃–Al(C₂H₅)₃, was used for the polymerization of methyl methacrylate. The yield of polymer increased up to an Al/Cr ratio of 12 and thereafter remained almost constant with increasing Al/Cr. The rate of polymerization increased linearly with increasing catalyst and monomer concentrations at Al/Cr = 12. The molecular weight, however, decreased with increasing catalyst concentration and increased with increasing monomer concentration, indicating anionic polymerization reaction. NMR studies of the polymers indicated the presence of a stereoblock structure, which changed to heteroblock structure in presence of triethylamine and hydroquinone as additives in the catalyst. In the light of these observations, the mechanism of the polymerization is discussed.     

Synthesis and characterization of chemically modified polystyrene as processable carbon fiber precursors

In this study, the chemically modified polystyrene was studied for improvement of polystyrene which had low carbon yield, as a carbon fiber precursor. The polystyrene was synthesized with divinylbenzene which was used as a cross-linking agent by the solution polymerization method. Then the synthesized polystyrene was nitrated with sulfuric and nitric acids solution (H₂SO₄/HNO₃) followed by reduction to form nitrogen-functional groups. The surface properties of the modified polystyrene were investigated by Fourier transfer infrared spectroscopy to confirm the introduction of functional groups on the modified polystyrene surfaces. The thermal properties of the modified polystyrene were measured by thermogravimetric analysis and differential scanning calorimetry. The morphologies of the electrospun polystyrene fibers by a chemical modification were observed by scanning electron microscopy. From the results, the nitrogen-functional groups were introduced on the modified polystyrene surfaces which affected the quantity of functional groups. Also, the chemical treatment affected the carbon yield of the polystyrene owing to the introduction of nitrogen-functional groups on polystyrene surfaces. Consequently, it was concluded that the chemical treatment of polystyrene fibers enables it to be used as a possible carbon fiber precursor.     

CYCLOPOLYMERIZATION OF DIPROPARGYL DERIVATIVES BY Cp2MoCl2-EtAlCl2 CATALYST SYSTEM

ABSTRACT

A Cp₂MoCl₂-EtAlCl₂ catalyst system was used for the cyclopolymerization of various dipropargyl derivatives having different functionalities. These catalyst systems were found to be very effective for the polymerization of some dipropargyl monomers to give a relatively high yield of polymer. The polymerization behaviors were strongly dependent on the functionalities of dipropargyl monomers. The polymerization of such dipropargyl monomers as 1,6-heptadiyne, diphenyldipropargyl methane, diethyldipropargyl malonate, etc. proceeded well to give a quantitative yield, whereas this catalyst system was found to be less effective for the polymerization of dipropargyl monomers having perfluoroalkyl groups and quaternary ammonium salts. The polymer structure of the resulting polymers was characterized by various instrumental methods such as NMR, IR, and UV-visible spectroscopies to have a conjugated polyene backbone system with cyclic recurring units. The portion of 5- and 6-membered rings of the present conjugated cyclopolymer were also discussed.