平面单测点法评价湿度和温度对药物稳定性的影响

利用均匀设计分散原理, 确定药物的湿度温度平面, 采用单测点法获得药物相关的降解动力学参数. 阿司匹林稳定性加速试验结果表明, 平面单测点法与恒温恒湿法和程序变温变湿法得到的降解动力学参数基本一致. 在药物降解程度及试验的湿度差和温度差相同的条件下, 平面单测点法结果的准确度和精密度均明显优于程序变温变湿法, 且装置简单. 与经典恒温恒湿法相比, 平面单测点法的误差较大, 但试验工作量减少.     

介绍一个变温动力学实验

本文介绍一个变温法研究酸催化蔗糖转化反应和乙酸乙酯水解反应速率的模型设计实验[1]。由lnc-t图求出近似活化能Ea和A。目前化学实验教材中变温动力学的内容很少[2],本文的实验设计内容可作为一个补充和参考。1数学模型近年来,由于计算机的普及和程序升温仪的改进,导致对程序升温研究药物稳定性方面的研究比较活跃,对计算模型的设计也有一些巧妙的构思[3,4]。但在化学实验教材中,变温动力学的内容却很少。在常温下,蔗糖转化反应和乙酸乙酯水解反应属于准一级反应,其速率方程为:-dc/dt=kc(1)将程序升温规律T=T(t)代入Arrhenius公式:(R=8.…     

乙酰氧肟酸的热稳定性分析

为预防化工生产、储运和使用中由乙酰氧肟酸(Acetohydroxamic acid, AHA)引发的火灾和爆炸事故, 采用绝热量热法对其热稳定性进行实验研究, 并将加速量热仪(Accelerating Rate Calorimeter, ARC)的测试结果与差示扫描量热仪(Differential Scanning Calorimetry, DSC)的结果进行了比较. ARC绝热测试结果表明, AHA的初始放热温度为352.68 K, 最高放热温度为465.82 K, 最大温升速率和最大温升速率时间分别为8.748 K•min^－1和382.65 min, 单位质量AHA生成气体的最大压力为2.22 MPa•g^－1. 根据ARC绝热测试结果, 采用速率常数法计算了AHA的动力学参数表观活化能和指前因子, 并求出了AHA的某种典型包装的不可逆温度和自加速反应温度. 研究结果表明, AHA的热稳定性较差, 爆炸性较强.     

纳米白藜芦醇脂质体的物理化学稳定性研究

纳米载药脂质体的物理化学稳定性,是其实际应用中的关键问题。文章采用薄膜旋转蒸发法-超声法制备了白藜芦醇纳米脂质体（RES-Lip）,采用透射电子显微镜观察其微观形貌,并考察RES-Lip的物理化学稳定性。通过电导法测定了RES-Lip的相变温度（Tm）,及其在凝聚过程的凝聚速率常数（Kco）和表观活化能（Eco）;采用动态透析-紫外分光光度法,研究了温度和pH对RES-Lip降解的影响。结果表明,RES-Lip为球形囊泡结构,粒径小于100 nm;RES-Lip的相变温度为64℃;凝聚速率常数Kco随体系温度升高而升高;表观活化能Eco为86.056 kJ/mol;RES-Lip的降解符合一级动力学模型,降解的表观活化能Ea为59.3157 kJ/mol,降解过程是吸热、自发、熵增过程。本实验制备得到的RES-Lip在4℃、pH=7.40的条件下储存,稳定性较好。     

高聚物的非等温结晶动力学——从不同速率的升温或降温DSC曲线解析结晶动力学参数

根据等温DSC法,测定结晶动力学参数在实验上存在着一定的局限性,结晶太快或太慢都难于获得可靠的结果,这就限定了能测定的温度区间。可见,等温DSC法测定结晶动力学参数具有获得的信息量少,结晶起始点难以确定,费时等缺点。这些缺点可通过等速变温DSC法来克服。然而,通过等速变温DSC法测定结晶动力学参数的方法至今还不完善。例如Ozawa曾基于Evans理论把Avrami方程推广于非等温结晶,从Ozawa方程通过等速变温DSC曲线可得到表征结晶机理的函数Avrami ＄数。和冷却结晶函数。Ozawa方法的不足是从其冷却结晶函数不能解析出表征结晶速率的参数。     

柠檬酸色谱分离的动力学模拟

报道一种在考虑柱床空隙率变化的条件下变温色谱动力学研究和参数测定的方法.以柠檬酸的提纯分离为实验例子,在分析柱上测定各模型参数,用这些热力学参数加入到平衡分散模型中,模拟在大型生产柱上的动力学行为,取得了非常满意的结果.     

电刷镀含钛合金非晶态镀层的晶化动力学(II)

用热分析仪研究非晶态材料的晶化动力学有两大类方法：等温法和变温法．变温法测定动力学参数的优点是简便，需要的样品量少，能在反应开始到结束的整个温度范围内连续计算动力学参数．晶化反应是一种相变反应．反应前后没有重量的变化，因此，只能采用差热分析法D’fA或差示扫     

低温等离子体处理化工恶臭污染物硫化氢的研究

采用电晕放电低温等离子体处理模拟硫化氢恶臭气体,考察了输入功率、初始浓度、气体湿度、停留时间等因素对降解效果和能量效率的影响,同时对反应过程进行了动力学研究。研究表明：输入功率以及停留时间对硫化氢降解的影响是积极的,但能量效率随着两者的增加先增大后减小。硫化氢的降解率随着初始浓度的增加而降低,而能量效率随着初始浓度的增加而增加。在气体湿度增加初期,硫化氢降解率和能量效率均随着气体湿度的增加而增加,当气体湿度为50%时达到最大值,然而随着气体湿度的进一步增加,其降解率和能量效率反而降低。对电晕放电低温等离子体处理硫化氢的反应动力学进行了分析,得到硫化氢的反应速率常数为kH2S=0.356 8 m3/（W·h）。     

基于光微热量-荧光光谱联用技术研究光催化热力学和动力学的温度效应

利用光微热量-荧光光谱联用技术,对光催化过程的热谱和光谱信息同步监测,获取了五个温度下,g-C_3N_4@Ag@Ag_3PO_4光催化降解罗丹明B的原位热动力学、光谱动力学信息,探究了温度对相关参数的影响。结果表明,催化降解反应分为三个阶段:(i)污染物和催化剂的光响应过程;(ii)光响应吸热和污染物降解放热的竞争过程;(iii)保持稳定的放热率。吸热和放热的竞争过程符合一级动力学,降解速率随着温度的升高而增大;稳定放热阶段为拟零级反应,在283.15 K、288.15 K、293.15 K、298.15 K、303.15 K下的放热速率分别为0.4668±0.3875μJ·s~(-1)、0.5314±0.3379μJ·s~(-1)、0.5064±0.3234μJ·s~(-1)、0.5328±0.3377μJ·s~(-1)、0.5762±0.3452μJ·s~(-1)。本研究为探究光催化过程的原位热力学、热动力学及光谱信息及机理的推测提供科学依据。     

丹酚酸B的热稳定性及其热分解动力学研究

用TG-DTG 方法研究了丹参的有效成分丹酚酸B 的热降解过程. 热重分析结果表明该物质的失重过程分两步进行. 笫一步为脱去吸附水, 其温度范围为305～373 K, 第二步为丹酚酸B 分子骨架大规模降解, 其温度范围在413～864 K. 用Friedman 和Ozawa-Flynn-Wall 两种方法分别计算出该药物降解过程中的三个阶段的活化能, 采用多步线性回归方法, 并参考常用的15 种热解机理函数, 确定了丹酚酸B 热降解过程最佳动力学模型为Fn-F2-F1.     

Critical thermodynamic analysis of differential scanning calorimetry for studying chemical kinetics

A critical thermodynamic analysis of differential thermal calorimetry is reported herein to gain further insight into the phenomena leading to the reported differences between kinetic parameters extracted from isothermal DSC methods and those from dynamic DSC methods. The sources have been identified for the variations observed in the total heat of reaction as a function of the heating rate in dynamic DSC experiments. The analysis clearly indicates that these variations are, in fact, to be anticipated. The relationships necessary for extracting kinetic data from both isothermal and dynamic experiments are derived rigorously by resorting to classical thermodynamics. This work was supported by the Cooperative State Research Service, U.S. Department of Agriculture, under Agreement No. 92-37500-7911.     

Influence of microwave radiation on free Candida antarctica lipase B activity and stability

The influence of microwave heating on free Candida antarctica lipase B activity and stability was studied over the temperature range from 40 to 110 degrees C. Concerning the lipase activity, identical initial rate and conversion yield were obtained under microwave radiation and classical thermal heating for the alcoholysis between ethyl butyrate and butanol in a solvent-free system. On the other hand, the kinetics of the free lipase inactivation in butanol appears to be influenced by the heating mode. The Arrhenius plot obtained under classical heating was linear over all the temperature range studied whereas a biphasic Arrhenius plot was obtained under microwaves. The non-classical effect of the microwave heating on the initial rate of the enzymatic inactivation was thus dependent on the temperature of incubation.     

无机化学实验的改进与探究——以“未知固体样品的分析”实验为例

以“未知固体样品的分析”实验为例,通过建立完整的未知固体样品筛选体系来指导完成该实验的改进。结果获得了改进无机化学实验的一般思路、方法及规律。这为经典实验的改进奠定了基础。     

呋喃西林水溶液在光和热作用下的稳定性

The influence of both light and heat on the stability of nitrofurazone aqueous solution was studied. Results show that in either heating experiments or the exposure to light at high temperatures, the degradation rate obeyed zero-order kinetics. The total rate constant ktotal caused by both light and heat can be divided into two parts: ktotal =kdark klight, where kdark and klight are the degradation rate constants caused by heat and light, respectively. The klight can be expressed as klight=Alight*exp(-Ea,light/RT)*E, where E is the illuminance of light, and Alight and Ea,light both are experimental constants. The values of these kinetic parameters were determined based on the experiments in the dark and upon exposure to three different light sources. Results show that the values of Alight and Ea, light varied with the light source. To save time, labor, and drugs, exponential heating experiments were employed and compared with the isothermal experiments. Results indicated that kinetic parameters obtained by exponential heating experiments are comparable to those obtained by isothermal experiments either in the dark or upon exposure to light.     

Prediction of the separation number of capillary columns in programmed temperature gas chromatographic analysis

The efficiency of capillary columns in programmed temperature analysis can be evaluated by calculation of the separation number (“Trennzahl”). A procedure for the prediction of this parameter at various initial temperatures, carrier gas pressures and heating rates, by using as the starting data the retention times and the peak widths obtained in some isobaric and isothermal runs is described. An equation is proposed that permits to obtain the values of the peak width at half height in any isothermal and linearly programmed temperature gas chromatographic run and therefore to calculate the separation number value. The effect on this parameter of the column polarity was investigated by using polar and non-polar compounds (n-alkanes and 1-alcohols).     

Some demonstrations of the effect of the heating rate on thermoanalytical curves

Thermoanalytical curves of two parallel competitive reaction systems and of two systems in which two mutually independent reactions occur concurrently are made by simulation, as well as isothermal curves of the systems. From these curves, an effect of heating rate is illustratively shown; one peak is observed in a derivative thermoanalytical curve at one heating rate, while a shoulder or two peaks appear in another derivative curve of the same reaction system at another heating rate. An advantage of thermal analysis over isothermal experiments, and its limitations, are discussed.     

End-life Prediction of Commercial PLA Used for Food Packaging through Short Term TGA Experiments： Real Chance or Low Reliability？

A long-term(about nine months) isothermal degradation experiment of two different commercial polylactide(PLA) samples used for food packaging was carried out at a relatively low temperature(423 K). Thermooxidative degradations of the same polymers were carried out in a thermogravimetric(TG) analyser, at higher temperatures(453 K ≤ T ≤ 523 K), under isothermal heating conditions. The obtained set of experimental TG data was used to determine the apparent activation energy(Ea) of degradation through two isothermal kinetic methods. The results from long-term experiment evidenced considerable mass loss for both PLA samples in the investigated period, but the experimental data were not in agreement with those from the short-term degradations at higher temperatures, thus suggesting a different degradation kinetics, and, then a low reliability of the lifetime predictions for polymers in service or degradation forecasts for the end of their life based on experiments at higher temperatures.     

The regression of isothermal thermogravimetric data to evaluate degradation Ea values of polymers: A comparison with literature methods and an evaluation of lifetime prediction reliability

The thermooxidative degradation of four well known polymers, polyethylene (PE), polystyrene (PS), polycarbonate (PC) and poly(methyl methacrylate) (PMMA), was carried out in a thermogravimetric (TG) analyser, at various temperatures (in the 473–533 K range), in isothermal heating conditions. The resulting set of experimental TG data was used to determine the apparent activation energy (E_a) of degradation through two isothermal literature methods, as well as through a very simple method we set up, based on the direct regression of the experimental mass loss data, in order to verify the general applicability of our method to various polymers. The results from different methods were in good agreement. Degradation experiments in dynamic heating conditions, which were also performed, gave E_a values in good agreement with those in isothermal heating conditions for PS, PC and PMMA, while for PE a large discrepancy was observed, which was discussed and interpreted. The results suggested the general applicability of our method to all polymers, independently on their structure and degradation mechanism. A long-term (about 13 months) isothermal degradation experiment was also carried out with the same polymers at relatively low temperature (423 K). Only PE and PS evidenced appreciable mass loss in the investigated period, but the experimental data were not in agreement with those from the short-term degradations at higher temperatures, thus suggesting different degradation kinetics, and a low reliability of the lifetime predictions for polymers in service based on experiments at higher temperatures.     

Predicting adsorption isotherms of low-volatile compounds by temperature programmed desorption: iodine on carbon

Equilibrium adsorption isotherms for low-volatile compounds are extremely difficult to measure. A simple technique using temperature programmed desorption (TPD) is proposed. It is demonstrated that the two parameters needed for constructing the Langmuir isotherm can be derived with data from the TPD technique alone. Thus, the Langmuir isotherms of iodine on AX-21 super-activated carbon were obtained with this technique. A series of TPD experiments for samples with different initial loadings of iodine were carried out by varying the heating rates which resulted in different peak desorption temperatures. The peak desorption temperature decreased as the initial loading was increased because of the re-adsorption effect. The Langmuir constant was derived from kinetic theory with the activation energy for desorption obtained from the experiment. The activation energy for desorption was 12.3 kcal/mol. The Langmuir constants determined by this technique were in comparable order of magnitude to the reported values for iodine on activated carbon. The saturation capacity of AX-21 for iodine could also be determined from the TPD data obtained from samples with different initial loadings. The estimated saturation capacity from the TPD experiment was 2.96 g I(2)/g AX-21, which was close to the experimentally measured saturation capacity of 3.25 g I(2)/g AX-21 for the same system.