Chromium(III)-imprinted silica gel for speciation analysis of chromium in environmental water samples with ICP-MS detection

A new chromium(III)-imprinted 3-(2-aminoethylamino) propyltrimethoxysilane (AAPTS)-functionalized silica gel sorbent was synthesized by a surface imprinting technique and was employed as a selective solid-phase extraction material for speciation analysis of chromium in environmental water samples prior to its determination by inductively coupled plasma mass spectrometry (ICP-MS). The prepared Cr(III)-imprinted silica gel shows the selectivity coefficient of more than 700 for Cr(III) in the presence of Mn(II). The static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Cr(III) were 30.5 mg g(-1) and 13.4 mg g(-1). It was also found that Cr(VI) could be adsorbed at low pH by the prepared imprinted silica gel, and this finding makes it feasible to enrich and determine Cr(VI) at low pH without adding reducing reagents. The imprinted silica gel sorbent offered a fast kinetics for the adsorption and desorption of both chromium species. Under the optimized conditions, the detection limits of 4.43 pg mL(-1) and 8.30 pg mL(-1) with the relative standard deviations (R.S.D.s) of 4.44% and 4.41% (C=0.5 ng mL(-1), n=7) for Cr(III) and Cr(VI) were obtained, respectively. The proposed method was successfully applied to the speciation of trace chromium in environmental water samples. To validate the proposed method, two certified reference materials were analyzed and the determined values were in a good agreement with the certified values. The developed method is rapid, selective, sensitive and applicable for the speciation of trace chromium in environmental water samples.     

Anion-exchange high-performance liquid chromatographic determination of ascorbic acid and hexavalent chromium in rat lung preparations after treatment with sodium chromate in vitro and in vivo

Simultaneous analysis of ascorbic acid and chromium (VI) in soluble fractions and bronchoalveolar lavage fluids of rat lungs treated with sodium chromate in vitro and in vivo was performed by anion-exchange high-performance liquid chromatography coupled to a photodiode-array detector. Absorbances at 265 and 370 nm were used for the determination of ascorbic acid and chromium (VI), respectively. The calibration graphs of standard solutions were linear in the test ranges of ascorbic acid an chromium (VI) (below 10 and 8 ppm, respectively). The detection limits of ascorbic acid and chromium (VI) were 1 and 0.5 ng, respectively. The recovery of ascorbic acid from lung tissues homogenized at pH 7.4 was 99%, and that of chromium (VI) was 96%, when tissues were homogenized under alkaline conditions (pH 11.4). Using this method, ascorbic acid levels in the soluble fractions and lavage fluids of normal rat lungs were determined. In the lung of a rat intratracheally injected with a saline solution of sodium chromate, ascorbic acid decreased to 80% of the normal level, and ca. 90% of the chromium (VI) was reduced within 4 min after injection, indicating that the ascorbic acid-related reduction of chromium (VI) is very rapid. The present method will be useful for studies of the reduction of chromium (VI) by ascorbic acid in biological systems.     

Liquid-liquid extraction of niobium(V) in the presence of other metals with high molecular mass amines and ascorbic acid

A novel method is proposed for the solvent extraction of niobium(V). A 0.1M solution of Aliquat 336S in xylene quantitatively extracts microgram quantities of niobium(V) from 0.01M ascorbic acid at pH 3.5-6.5. Niobium from the organic phase is stripped with 0.5M nitric acid and determined spectrophotometrically in the aqueous phase as its complex with TAR. The method permits separation of niobium not only from tantalum(V) but also from vanadium(IV), titanium(IV), zirconium(IV), thorium(IV), chromium(III), molybdenum(VI), uranium(VI), iron(III), etc. Niobium from stainless steel was determined with a precision of 0.42%.     

Determination of chromium in waste-water and cast iron samples by fluorescence quenching of rhodamine 6G

A new simple, selective and sensitive fluorescence quenching method was developed to determine chromium with rhodamine 6G. The method is based on the oxidation of rhodamine 6G by chromium(VI) in sulfuric acid solution. The linear calibration graph was obtained in the range 8-80 ng ml(-1) chromium(VI). The detection limit is 0.8 ng ml(-1). The method was applied successfully to the determination of chromium in waste water and cast iron samples.     

Determination of Cr3+, CrO42-, and Cr2O72- in environmental matrixes by high-performance liquid chromatography with diode-array detection (HPLC-DAD)

A high-performance liquid chromatographic method with diode array detection (HPLC-DAD), based on chelation with ammonium pyrrolidinedithiocarbamate (APDC), has been developed for the determination of chromium species. Determination of Cr3+, CrO42-, and Cr2O72- was performed for standards and synthetic environmental matrixes. This method is robust, rugged, and can be used for rapid routine determination of chromium species with high precision and reliability. Sample pretreatment is simple. The method is capable of discriminating not only between Cr(III) and Cr(VI) but also between the chemical forms of Cr(VI) - CrO42- and Cr2O72-. By analysis of numerous samples the method has been shown to be selective, sensitive, and free from matrix interference, which is crucial for the determination of chromium species in difficult-to-analyze environmental matrixes. This method has been validated by means of an interlaboratory study. Although different speciation techniques were used during this study, there was good agreement between results from the two laboratories. The method detection limits were 7 and 4 mg L(-1) for Cr3+ and Cr2O72-, respectively. Recoveries of the analytes from spiked samples were 98% and 100% for Cr3+ and Cr2O72-, respectively. Both were based on a 10-mL sample volume spiked with 0.4 mg L(-1) chromium.     

Iodnitrotetrazolium chloride-A new analytical reagent for determination of chromium

The extraction of chromium (VI) with iodnitrotetrazolium chloride (INT) was studied spectrophotometrically. The basic spectrophotometric characteristics of the ion associated formed were determined. Using different methods it was found that the ratio between chromium and INT was 1:1. The molar absorptivity of the associate is (250) = (3.70 +/- 0.08) x 10(4) 1.mole(-1).cm(-1). Performing the reaction in acid medium (0.1-1.1M hydrochloric acid) allowed the determination of chromium in the presence of large amounts of W(VI), Mo(VI), Fe(III) and V(V). Hence INT is suggested as a sensitive and selective reagent for extractive-spectrophotometric determination of microquantities of chromium(VI).     

Microdetermination Par Polarographie Impulsionnelle Differentielle Du Chrome (VI) Present Dans Les Ciments Industriels

Abstract

The toxicological literature often mentions that chromium(VI), present and added to cements for technical reasons, induce dermatosis. Good analytical techniques are not available. The D.P.P. method proposed here for the microdetermination of chromium (VI) in cements is fast and selective. The cation is solubilized by stirring the cement with distilled water. After filtration, the solution is submitted to differential pulse polarography. Generally, samples analysed contain between 1 and 12 mg of chromium (VI) per kg of cement. The potential peak is -0.19 V v.s. S.C.E. for the pure chromium (VI) solution and is shifted toward between -0.25 and -0.30 V v.s. S.C.E. when chromium (VI) is extracted from real cement samples The detection limit is 0.3 ppm.     

Chromium speciation by a surfactant-coated alumina microcolumn using electrothermal atomic absorption spectrometry

A simple and convenient method has been developed for the speciation of chromium(III) and chromium(VI) in aqueous solutions using a sodium dodecyl sulphate coated alumina micro-column (1.5 cm x 5 mm i.d.) and graphite furnace-atomic absorption spectrometry (GF-AAS). Under the optimized conditions (pH 0.6, adjusted with hydrochloric acid; flow rate, 1 ml min(-1)) chromium(VI) is retained on the column and chromium(III) is collected and determined by GF-AAS. Total chromium is directly determined by GF-AAS and chromium(VI) is calculated by difference. The relative standard deviations (10 replicate analyses) at the 20 mug l(-1) level for chromium(III) and chromium(VI) and at the 40 mug l(-1) level for total chromium were 1.4%, 3.6% and 1.8%, and the corresponding limits of detection (based on 3sigma) were 0.57 mug ml(-1), 0.61 mug ml(-1) and 0.35 mug l(-1) respectively. No large interference effects have been observed from other investigated species and the method has been successfully applied to a range of water samples.     

Simultaneous determination of hexavalent and total chromium in water and plating baths by spectrophotometry

A new spectrophotometric determination method of hexavalent chromium in waste water and plating baths is described based on the oxidation of beryllon III by chromium(VI) in 0.02M sulphuric acid medium. The decrease in the absorbance of beryllon III was measured at 482 nm with an apparent molar absorptivity of 5.15 x 10(4)1.mole(-1).cm(-1). Beer's law was obeyed for chromium(VI) over the range 0-25 mug/25 ml. After the oxidation of Cr(III) to Cr(VI) by ammonium persulphate, total chromium can be determined. Therefore, chromium(III) can be calculated by subtracting chromium(VI) from total chromium. The detection limit is 0.015 and 0.020 mug/25 ml for chromium(VI) and total chromium, respectively. A sensitive spectrophotometric method for trace Cr(III) and Cr(VI) in waste water and plating baths was developed with good precision and accuracy. The reaction is also discussed.     

Determination of hexavalent chromium by on-line dialysis ion chromatography in a matrix of strong colourants and trivalent chromium

Hexavalent chromium detection in the presence of a high load of colourants without any false positive and in-procedure oxidation of Cr(III) is an important area of study. Colourants are a class of interfering substances in many spectroscopic analyses and chromatographic separations and detection. A purification method using an on-line dialysis technique for ion chromatography (IC) has been developed to remove water-soluble anionic dyes and particulate colourants and other substances to facilitate Cr(VI) quantification and the method is discussed. The dialysis was optimized with Cr(VI) standard solutions for quantification. The efficacy of the procedure for the removal of anionic dyes and detection of Cr(VI) was checked with a Cr(VI) spiked synthetic preparation containing a water-soluble dye and trivalent chromium. Soluble Cr(VI) extracted with organic dyes from environmental samples was analyzed. The method has a detection limit of 5 microg/l, recovery rate of 100% and analysis time less than 20 min.     

Speciation of Chromium in Natural Waters,Tea, and Soil with Membrane Filtration Flame Atomic Absorption Spectrometry

A sensitive and selective method was developed for the speciation of chromium(III) and chromium(VI) in environmental samples based on membrane filtration and determination by flame atomic absorption spectrometry. Chromium(III) reacts with cochineal red A, yielding a complex that is adsorbed on a cellulose acetate membrane filter, whereas chromium(VI) remains in aqueous solution, permitting separation. After reduction of chromium(VI) to chromium(III) with hydroxylamine hydrochloride, the total concentration of chromium was determined, and the concentration of chromium(VI) was calculated by subtraction. The pH, amount of cochineal red A, and sample volume were optimized on the basis of the recovery of Cr(III). The influence of matrix ions was also investigated. The preconcentration factor was 94. The detection limit (3 sigma) for Cr(III) was 1.4 micrograms per liter. The method was validated using environmental certified reference materials. The method was successfully employed for the speciation of chromium in wastewater and lake water.     

Selective determination of airborne hexavalent chromium using inductively coupled plasma mass spectrometry

A new method for determining ultra-trace levels of hexavalent chromium in ambient air has been developed. The method involves a 24-h sampling of air into potassium hydroxide solution, followed by silica gel column separation of chromium (VI), then preconcentration by complexation and solvent extraction. The chromium (VI) complex was dissolved in nitric acid. The resultant chromium ions were determined by inductively coupled plasma mass spectrometry (ICP–MS) using a dynamic reaction cell (DRC) with ammonia as the reactive gas to reduce polyatomic interferences. The interconversion of chromium in potassium hydroxide solution and air sample matrix were investigated under ambient conditions. It was found that there was no conversion of chromium (VI) into chromium (III) species. However, it was observed that some chromium (III) species were converted into chromium (VI) species. For a KOH solution containing 100 μg l⁻¹ of chromium (III) species, the rate of conversion was found to be 3% after 24 h exposure, 8% after 48 h, 10% after 72 h and no further conversion was observed thereafter. However, in a solution containing air sample matrix, 9.3% of chromium (III) converted to chromium (VI) within 6 h, and during the course of a 11-day exposure period, 13% (range 8–17%) of chromium (III) converted to chromium (VI). The method detection limit (MDL) for chromium (VI) in potassium hydroxide solution (0.025 M) was found to be 2×10⁻² μg l⁻¹. This is equivalent to 0.2 ng m⁻³ (for 23 m³ air sampled into 200 ml of KOH solution over a 24-h period). The recovery of spiked chromium (VI) from solutions containing air sample matrix was 95±9% (n=8). Matrix related interferences were estimated to be less than 10% based on recovery studies. The concentration of airborne chromium (VI) in Sydney residential areas was found to be less than 0.2 ng m⁻³, however, in industrial areas the concentrations ranged from 0.2 to 1.3 ng m⁻³ using this analytical procedure.     

Solid phase extraction of chromium(VI) from aqueous solutions by adsorption of its diphenylcarbazide complex on a mixed bed adsorbent (acid activated montmorillonite-silica gel) column

A novel approach has been developed for the solid phase extraction of chromium(VI) based on the adsorption of its diphenylcarbazide complex on a mixture of acid activated montmorillonite (AAM)-silica gel column. The effect of various parameters such as acidity, stability of the column, sample volume, interfering ions, etc., were studied in detail. The adsorbed complex could be easily eluted using polyethylene glycol-sulfuric acid mixture and the concentration of chromium has been determined using visible spectrophotometry. The calibration graph was linear in the range 0-1microgmL(-1) chromium(VI) with a detection limit of 6microgL(-1). A highest preconcentration factor of 25 could be obtained for 250mL sample volume using glass wool as support for the mixed bed adsorbent. Chromium(VI) could be effectively separated from other ions such as nickel, copper, zinc, chloride, sulfate, nitrate, etc., and the method has been successfully applied to study the recovery of chromium in electroplating waste water and spiked water samples.     

Speciation of Cr(III) and Cr(VI) using solid phase extraction and determination of total As inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometric (ICP-AES) method was developed for speciation and simultaneous determination of Cr and As, since these two analytes are commonly determined in various water samples in order to assess their toxicity. The objective of this research was to study the speciation of Cr(III), Cr(VI) in the presence of As(III) and/or As(V) using solid phase extraction (SPE) and ICP-AES. For these measurements, four spectral lines were used for each analyte with the purpose of selecting the most appropriate for each element. Finally with the use for first time of a cation-exchange column filled with benzosulfonic acid and elution with HCl, the speciation in solutions which contained [Cr(III)?+?Cr(VI)?+?As(V)] and [Cr(III)?+?Cr(VI)?+?As(III)] was examined. It was demonstrated that the separation of the two chromium species is almost quantitative and the simultaneous determination of chromium species and total arsenic analytes is possible, with very good performance characteristics. The estimated limits of detection for Cr(III), Cr(VI), As(III) and/or As(V) were 0.9?µg?L^?1, 1.1 µg?L^?1, 4.7 µg?L^?1 and 4.5 µg?L^?1 respectively, the calculated relative standard deviations (RSDs) were 3.8%, 4.1%, 5.2% and 5.1% respectively, and finally the accuracy of the methods was estimated using a certified aqueous reference material and found to be 5.6% and 4.8% for Cr(III) and Cr(VI) respectively. The method was applied to the routine analysis of various water samples.     

Determination of Dihydroxybenzenes in Plastic Food Packaging Materials and in Food Simulating Liquids Using Capillary Electrophoresis

A capillary electrophoresis method has been developed to determine 1,2-dihydroxybenzene and 1,3-dihydroxybenzene in the food simulants distilled water, 3% acetic acid, 15% ethanol, and olive oil. Both substances, used as monomers and additives to make food packaging plastics, could be analyzed within 15 min. The 1,4-dihydroxybenzene isomer was unretained and eluted with the electroosmotic flow, and so the CE method can give only a semi-quantitative estimate of this isomer if it is present as a migrant. The analytical recovery for the 1,2- and 1,3-isomers from spiked simulants was good at 87% to 98% except for 1,2-dihydroxybenzene which could only be recovered to the extent of 58% from olive oil. Calibration graphs were linear and the limit of detection for each substance was 0.6 mg/kg, which is well below migration limits for these substances. It is concluded that CE offers a rapid and reliable analysis for the control of migration from plastics intended for food contact which employ 1,2-dihydroxybenzene or 1,3-dihydroxybenzene during manufacture, and offers a screening method for 1,4-dihydroxybenzene migration.     

Simultaneous Determination of Chromium Species in Water and Plant Samples at Trace Levels by Ion Chromatography–Inductively Coupled Plasma-Mass Spectrometry

Ion chromatography–inductively coupled plasma-mass spectrometry (IC–ICP-MS) was used for the identification and quantification of chromium species. Chromium(III) and chromium(VI) were separated and determined by IC–ICP-MS. The separation was achieved using an anion exchange column with 0.55?M HNO₃ as mobile phase. It was a particular goal of this work to exclusively use nitric acid for elution in order to reduce interferences in the ICP-MS system. Analytical figures of merit were calculated under the optimum conditions by developing calibration plots in a concentration range of 0.50–250?µg/L for both species. The detection limits for Cr(III) and Cr(VI) were 0.09 and 0.03?µg/L, respectively. Spiked recovery tests were used to evaluate the applicability of the analytical method in environmental samples, and the recoveries ranged between 97 and 103% for both analytes. The accuracy of the method for total chromium content was validated through the analysis of a spring water-certified reference material (UME 1201), and the obtained results were in good agreement with the certified value. Lettuce seedlings were cultivated to evaluate the intake levels of these species. In addition, the bioaccessibility of Cr(III) and Cr(VI) from the lettuce seedlings in simulated gastric and intestinal fluids media was examined.     

Catalytic adsorptive stripping determination of trace chromium (VI) at the bismuth film electrode

A sensitive adsorptive stripping voltammetric protocol at a bismuth-coated glassy-carbon electrode for trace measurements of chromium (VI) in the presence of diethylenetriammine pentaacetic acid (DTPA) is described. The new protocol is based on accumulation of the Cr-DTPA complex at a preplated bismuth film electrode held at −0.80 V, followed by a negatively-going square-wave voltammetric waveform. Factors influencing the stripping performance including the film preparation, solution pH, DTPA and nitrate concentrations, deposition potential and deposition time, have been optimized. The resulting performance compares well with that observed for analogous measurements at mercury film electrodes. A preconcentration time of 7 min results in a detection limit of 0.3 nM Cr(VI) and after 2 min a relative standard deviation at 20 nM of 5.1% (n = 25). Applicability to river water samples is demonstrated. The attractive behavior of the new “mercury-free” chromium sensor holds great promise for on-site environmental and industrial monitoring of chromium (VI). Preliminary data in this direction using bismuth-coated screen-printed electrodes are encouraging.     

Simultaneous determination of arsenic species and chromium(VI) by high-performance liquid chromatography-inductively coupled plasma-mass spectrometry

The simultaneous determination of As(III), As(V), monomethylarsenic acid (MMA), dimethylarsinic acid (DMA) and Cr(VI) in fresh water has been carried out by coupling an anion-exchange column to an inductively coupled plasma-mass spectrometer. Optimisation of chromatographic conditions led to baseline separation of signals from the five species in approximately 9 min using gradient elution. Detection limits were 0.02-0.05 microg As l(-1) and 5.5 microg Cr l(-1). Repeatability was 2-3% for arsenic species and higher, i.e., 8%, for Cr(VI) due to the higher background for this species. Arsenic species and hexavalent chromium stability in surface water samples was evaluated, and storage conditions were set to 1 day at 4 degrees C in polyethylene flasks (without acidification) in order to avoid As(III)-As(V) conversions. The method was applied to the analysis of surface water.     

Preconcentration and spectrophotometric determination of chromium(vi) in natural waters by coprecipitation with barium sulfate

A selective preconcentration of chromium(VI) is proposed for analysis of natural waters. Chromium(VI) is quantitatively separated from chromium(III) by coprecipitation with barium sulfate; salicylic acid is used as a masking agent for iron(III), aluminum(III) and chromium(III). The precipitate is fused with alkali carbonate, and the chromium(VI) in the melt is isolated with hot water and determined spectrophotometrically with diphenylcarbazide. The detection limit is 0.02 μg l^-1 the relative standard deviation for chromium(VI) in river water is less than 5%.     

Speciation of V, Cr and Fe by capillary electrophoresis-bandpass reaction cell inductively coupled plasma mass spectrometry

Capillary electrophoresis-dynamic reaction cell inductively coupled plasma mass spectrometry (CE-DRC-ICP-MS) for the speciation of iron(III/II), vanadium(V/IV) and chromium(VI/III) is described. Two different CE migration modes were employed for separating the six metal ions using pre-capillary complexation. One is counter-electroosmotic mode in which iron(III/II) and vanadium(V/IV) ions were well separated using a 60 cm x 75 microm i.d. fused silica capillary. The voltage was set at +22 kV and a 15 mmol l(-1) tris(hydroxymethyl)aminomethane (Tris) buffer (pH 8.75) containing 0.5 mmol l(-1) ethylenediaminetetraacetic acid (EDTA) and 0.5 mmol l(-1) ortho-phenanthroline (phen) was used as the electrophoretic buffer. The other is co-electroosmotic mode in which chromium(VI/III) ions were well separated while the applied voltage was set at -22 kV and a 10 mmol l(-1) ammonium citrate buffer (pH 7.7) containing 0.5 mmol l(-1) diethylenetriaminepentaacetic acid (DTPA) and 0.01% polybrene was used as the electrophoretic buffer. The mass spectra were measured at m/z 51, 52 and 56 for V. Cr and Fe, respectively. The interfering polyatomic ions of 35Cl16O+, 40Ar12C+ and 40Ar16O+ on 51V+, 52Cr+ and 56Fe+ determination were reduced in intensity significantly by using NH3 as the reaction cell gas in the DRC. The detection limits were in the range of 0.1-0.5, 0.4-1.3 and 1.2-1.7 ng ml(-1) for V, Cr and Fe, respectively. Applications of the method for the speciation of V, Cr and Fe in wastewater were demonstrated. The recoveries were in the range of 92-120% for various species.