Ag负载KTa1-xNbxO3-BaTiO3颗粒掺杂P(VDF-TrFE-CTFE)复合材料的制备及介电性能

通过光照还原法制备了银颗粒负载的铌钽酸钾-钛酸钡复合粉体（Ag/KTN-BT）,并将其与聚偏氟乙烯-三氟乙烯-三氟氯乙烯（P（VDF-TrFE-CTFE））聚合物复合,获得Ag/KTN-BT聚合物基复合材料。研究发现,Ag/KTN-BT填料颗粒在聚合物基体中分散均匀,复合材料结构致密,无明显气孔和裂纹,且具有较好的柔韧性。银纳米颗粒的负载,一方面在复合材料中引入了额外的界面,导致界面极化作用增强,明显提高复合材料的介电常数;另一方面银纳米颗粒的量子尺寸效应和库伦阻塞效应使得复合材料保持较低的介电损耗。当填充体积分数为20%的Ag/KTN-BT颗粒时,聚合物基复合材料的介电常数大幅提升,从聚合物的37提升到125（100 Hz）,介电损耗仅为0.12。与KTN-BT基复合材料对比,Ag/KTN-BT基复合材料也显示出较好的介电性能。     

Microstructural design for enhanced mechanical property and shape memory behavior of polyurethane nanocomposites: Role of carbon nanotube,montmorillonite, and their hybrid fillers

The recent rapid development of technology has demanded smart materials with tailoring a bridge between macro properties and sophisticated micro and nano characteristic. Principally, shape memory polymers (SMPs) will come to play as an indispensable part of numerous aspects of human activity. Nevertheless, the low mechanical strength and thermal conductivity of SMPs have primarily restricted their applications. To impart shape memory behaviour and mechanical properties, we fabricated a series of composites by a feasible and commercial melt-mixing method. Thus, a series of fast heat-actuated shape memory polymer composite with greatly enhanced stretch-ability, mechanical stiffness, dynamic-modulus, rheological qualities, recovery and fixity ratio was prepared by incorporating multi-walled carbon nanotubes (CNT), montmorillonite (MMT) and CNT:MMT hybrid into thermoplastic polyurethane (TPU). Noteworthy, CNT-based specimens exhibited superior mechanical properties than those of MMT-based samples, and interestingly, the hybrid composites featured a synergistic effect due to the sacrificial role of MMT nanoplatelets for adjusting the dispersion of CNT nanotubes. Microstructural observations indicated that the crystallization percentages of the composites were generally higher than that of pristine TPU; therefore, the shape-memory performance of the specimens improved notably in the case of the hybrid composites owing to creating more interfacial zone with CNT:MMT nanoparticles as compared to other simple composites. This study proved that the simultaneous incorporation of CNT and MMT nanoparticles not only granted outstanding mechanical properties, but also improved the overall shape memory behaviour of the composites by systematical localization of the nanoparticles without any functionalization or modification.     

Glass fiber reinforced bismaleimide/epoxy BaTiO3 nano composites for high voltage applications

BaTiO₃/bismaleimide/epoxy/glass fiber reinforced composites were prepared using E-glass fiber (E-GF) and silane coated E-glass fiber (SC-EGF) separately as reinforcement. BaTiO₃ nanoparticles were prepared by hydrothermal method. Results show that the addition of BaTiO₃ nanoparticles has significant effects on the mechanical and dielectric properties of the composite. Both E-GF and SC-EGF reinforced BaTiO₃/bismaleimide/epoxy composites with 2 wt percentages of BaTiO₃ nanoparticles showed improved tensile strength, flexural strength and dielectric constant and those with 3% showed high dielectric strength indicating this composition is more adaptable for high voltage insulating applications. Dielectric constants and dielectric loss of the fabricated nanocomposites have been obtained at higher frequencies (in GHz) by using Vector Network Analyser at room temperature and was found to be highest for the BMI-Epoxy nanocomposite with 1% weight nanofiller.     

Ag Nanoparticle-Incorporated Natural Rubber for Mechanical Energy Harvesting Application

The energy conversion performance of the triboelectric nanogenerator (TENG) is a function of triboelectric charges which depend on the intrinsic properties of materials to hold charges or the dielectric properties of triboelectric materials. In this work, Ag nanoparticles were synthesized and used to incorporate into natural rubber (NR) in order to enhance the dielectric constant for enhancing the electrical output of TENG. It was found that the size of Ag nanoparticles was reduced with the increasing CTAB concentration. Furthermore, the CTAB surfactant helped the dispersion of metallic Ag nanoparticles in the NR-insulating matrix, which promoted interfacial polarization that affected the dielectric properties of the NR composite. Ag nanoparticle-incorporated NR films exhibited an improved dielectric constant of up to almost 40% and an enhanced TENG performance that generated the highest power density of 262.4 mW/m².     

Fabrication of thermoplastic polyurethane composites with a high dielectric constant and thermal conductivity using a hybrid filler of CNT@BaTiO3

Thermoplastic polyurethane composites with an excellent dielectric constant and high thermal conductivity were obtained using CNT@BaTiO₃ as a filler through a low-speed melt extrusion method. Before preparing the hybrid filler for the composite, the filler particles were surface modified to ensure that the outer surfaces could facilitate the reaction among particles to form the hybrid and ensure complete dispersion in the thermoplastic polyurethane matrix. After confirming the proper surface treatment of the filler particles using infrared spectroscopy, thermal degradation analysis and field emission scanning electron microscopy, they were used to prepare the composite materials at a processing temperature of 200 °C. The thermal stability, thermomechanical properties, mechanical properties, thermal conductivity, and dielectric properties of the composites were investigated. Compared to the neat thermoplastic polyurethane matrix, the prepared composite exhibited a higher thermal stability, approximately 300% higher storage modulus, higher tensile strength and elongation at break values, approximately three times higher thermal conductivity (improved from 0.19 W/(m.K) to 0.38 W/(m.K), and approximately five times larger dielectric constant at high frequencies (at 1 MHz a dielectric constant of 19.2 was obtained).     

Preparation of Polylactide/Poly(ether)urethane Blends with Excellent Electro-actuated Shape Memory <Emphasis Type="Italic">via</Emphasis> Incorporating Carbon Black and Carbon Nanotubes Hybrids Fillers

In this work, hybrid conductive fillers of carbon black (CB) and carbon nanotubes (CNTs) were introduced into polylactide (PLA)/thermoplastic poly(ether)urethane (TPU) blend (70/30 by weight) to tune the phase morphology and realize rapid electrically actuated shape memory effect (SME). Particularly, the dispersion of conductive fillers, the phase morphology, the electrical conductivities and the shape memory properties of the composites containing CB or CB/CNTs were comparatively investigated. The results suggested that both CB and CNTs were selectively localized in TPU phase, and induced the morphological change from the sea-island structure to the co-continuous structure. The presence of CNTs resulted in a denser CB/CNTs network, which enhanced the continuity of TPU phase. Because the formed continuous TPU phase provided stronger recovery driving force, the PLA/TPU/CB/CNTs composites showed better shape recovery properties compared with the PLA/TPU/CB composites at the same CB content. Moreover, the CB and CNTs exerted a synergistic effect on enhancing the electrical conductivities of the composites. As a result, the prepared composites exhibited excellent electrically actuated SME and the shape recovery speed was also greatly enhanced. This work demonstrated a promising strategy to achieve rapid electrically actuated SME via the addition of hybrid nanoparticles with self-networking ability in binary PLA/TPU blends over a much larger composition range.     

Preparation of Polylactide/Poly(ether)urethane Blends with Excellent Electro-actuated Shape Memory via Incorporating Carbon Black and Carbon Nanotubes Hybrids Fillers

In this work, hybrid conductive fillers of carbon black(CB) and carbon nanotubes(CNTs) were introduced into polylactide(PLA)/thermoplastic poly(ether)urethane(TPU) blend(70/30 by weight) to tune the phase morphology and realize rapid electrically actuated shape memory effect(SME). Particularly, the dispersion of conductive fillers, the phase morphology, the electrical conductivities and the shape memory properties of the composites containing CB or CB/CNTs were comparatively investigated. The results suggested that both CB and CNTs were selectively localized in TPU phase, and induced the morphological change from the sea-island structure to the co-continuous structure. The presence of CNTs resulted in a denser CB/CNTs network, which enhanced the continuity of TPU phase.Because the formed continuous TPU phase provided stronger recovery driving force, the PLA/TPU/CB/CNTs composites showed better shape recovery properties compared with the PLA/TPU/CB composites at the same CB content. Moreover, the CB and CNTs exerted a synergistic effect on enhancing the electrical conductivities of the composites. As a result, the prepared composites exhibited excellent electrically actuated SME and the shape recovery speed was also greatly enhanced. This work demonstrated a promising strategy to achieve rapid electrically actuated SME via the addition of hybrid nanoparticles with self-networking ability in binary PLA/TPU blends over a much larger composition range.     

Enhancement of thermal conductivity and tensile strength of liquid silicone rubber by three-dimensional alumina network

ABSTRACT

Rapidly increasing demands for higher integration density and stability of electronic devices embrace higher requirements for thermally conductive silicone rubber, which is promisingly used in ultra-thin components. In this work, alumina whiskers (AWs) and alumina flakes (AFs) are used to modify liquid silicone rubber (LSR) by fabricating binary (AFs/LSR) or ternary (AWs/AFs/LSR) composites. The thermal conductivity and mechanical strength of the binary and ternary composites were investigated. Thermal conductivity of the binary AFs/LSR composite (25AFs/LSR) was 0.1990 W m^?1 K^?1, while the thermal conductivity of the ternary AFs/AWs/LSR composite (20AFs/5AWs/LSR) was 0.2655 W m^?1 K^?1. Furthermore, the tensile strength of the ternary AWs/AFs/LSR composites increased by 180.9% as compared with the binary system, increased to 7.81 MPa from 2.78 MPa due to the introduction of 1 wt% AWs. As a reason, a significant synergistic effect of AWs and AFs in the enhancement of both thermal and mechanical properties of the LSR was proved. Furthermore, the dielectric property measurements demonstrated that the ternary composites exhibited a lower dielectric constant and dielectric loss, indicating that the AWs/AFs/LSR composites were qualified to be applied in the field of electronic devices.     

Synergistic effects between iron–graphene and melamine salt of pentaerythritol phosphate on flame retardant thermoplastic polyurethane

A comparison of melamine salt of pentaerythritol phosphate (MPP), and a synergistic agents, iron–graphene (IG) was performed in thermoplastic polyurethane (TPU) by masterbatch‐melt blending on thermal and flame retardant properties. The flame retardant properties of TPU composites were characterized by limiting oxygen index (LOI), UL 94 and cone calorimeter test (CCT). The CCT results revealed that IG can significantly enhance flame retardant properties of MPP in TPU. The peak heat release rate of neat TPU and flame retardant TPU/MPP composites decreased from 2192.6 and 226.7 to 187.2 kW/m² compared with that of TPU containing 0.25 wt% IG. The thermal stability and thermal decomposition of TPU composites were characterized by thermogravimetric analysis (TGA) and thermogravimetric/Fourier infrared spectrum analysis (TG‐IR). The results indicated IG and MPP can improve the thermal stability of TPU. The formation of thermal conductive network by IG can promote the decomposition of MPP into nonflammable melt, which can play the role of heat barrier and restrict the diffusion of fuels into combustion zone and access of oxygen to the unburned fuels. Copyright © 2016 John Wiley & Sons, Ltd.     

Microencapsulation of ammonium polyphosphate with hydroxyl silicone oil and its flame retardance in thermoplastic polyurethane

Microencapsulated ammonium polyphosphate (MAPP) is prepared using hydroxyl silicone oil by in situ polymerization and characterized by XPS. Microencapsulation gives MAPP better water resistance and flame retardance compared with APP in thermoplastic polyurethane (TPU). Thermal stability and fire resistance behavior have been analyzed and compared. The LOI value of the TPU/MAPP composite is higher than that of the TPU/APP composite. The UL 94 rating of the TPU/MAPP composite is V-0 at the 20 wt% additive level, whereas TPU/APP gives V-2 rating at the same loading level. The water resistant properties of the TPU composites are studied. Results of the cone calorimeter and microscale combustion calorimeter experiment show that MAPP is an effective flame retardant in TPU compared with APP.     

Polyaniline/Silver Nanoparticle-Doped Multiwalled Carbon Nanotube Composites

A simple method was used to synthesize the hybrid nanocomposites consisting of the functionalized multiwalled carbon nanotube composites (MWCNTs) with the polyaniline incorporated silver nanoparticles (a-MWCNT/PANI-Ag) through an emulsion polymerization at room temperature in order to enhance the electrical conductivity of polyaniline. The electrical conductivity of the composite with the incorporated Ag nanoparticles was 5% higher than the same weight percent for the composite without Ag nanoparticles, and the thermal stability was dramatically increased from 54% for the composite (a-MWCNT/PANI) to 69% through the incorporation of the Ag nanoparticles at 830°C. Additionally, the advantages of the Ag nanoparticles, including the improved electrical and thermal properties without damage to the polyaniline structure, were confirmed using FTIR and Raman spectroscopy.     

Improved dielectric and mechanical properties of polystyrene-hybrid silica sphere composite induced through bifunctionalization at the interface

Hybrid silica spheres (HS) of size 270-350 nm with vinyl and aminopropyl surface groups were incorporated in polystyrene (PS), and its effect on dielectric properties, coefficient of thermal expansion (CTE), and strength of PS-HS composite was studied. Incorporation of HS in PS followed a decrease in the dielectric constant from 3.2 for PS to 2.6 for composite with 7.5 vol % HS. The decrease in the dielectric constant was attributed to (i) increased interfacial porosity, (ii) formation of anhydrous HS having low dielectric constant, during hot processing of the composites, and (iii) dispersion and preservation of the anhydrous HS in the hydrophobic matrix. The dielectric constant of the composites with HS content up to 7.5 vol % does not vary much with temperature in the range from -20 to 65 °C. These composites also exhibited reduced CTE and improved flexural strength/stiffness due to good interfacial bonding through HS vinyl groups and dispersion of the filler in the matrix. The dielectric loss increased with HS content, and the loss measured for 7.5 vol % PS-HS composite was 6 × 10(-3), as compared to 10(-4) for PS. At HS loading above 7.5 vol %, the tendency of HS to agglomerate and form percolated structure lead to an increase in the dielectric constant and decrease in the mechanical properties of the composites.     

Enhanced thermal conductivity and mechanical properties of polymeric composites through formation of covalent bonds between boron nitride and rubber chains

Hexagonal boron nitride (BN) platelets, also known as white graphite, are often used to improve the thermal conductivities of polymeric matrices. Due to the poor interfacial compatibility between BN platelets and polymeric matrices, in this study, polyrhodanine (PRd) was used to modify BN platelets and prepared functionalized BN-PRd platelets, thereby enhancing the interfacial interaction between the thermal conductive filler and polymeric matrix. Then, BN-PRd platelets were dispersed into the nitrile butadiene rubber (NBR) matrix to yield high thermally conductive composites. The presence of N? C═S groups in PRd allowed the combination of PRd and NBR chains containing stable covalent bonds via vulcanization reaction. The thermal conductivity of the as-prepared 30 vol% BN-PRd/NBR composite reached 0.40 W/mK, representing an increment of 135% over pure NBR (0.17 W/mK). In addition, the largest tensile strength of NBR composite containing 30 vol% BN-PRd platelets was 880% times of pure NBR. The 30 vol% BN-PRd/NBR composite also displayed a relatively high dielectric constant (9.35 at 100 Hz) and a low dielectric loss tangent value (0.07 at 100 Hz), indicating their usefulness as dielectric flexible materials of microelectronics. In sum, the simplicity and good efficiency of formation of covalent bonds between boron nitride and rubber chains look very promising for large-scale industrial production of high thermally conductive composites.     

Improving piezoelectric performance of lead-free polymer composites with high aspect ratio BaTiO3 nanowires

Flexible and lead-free piezoelectric nanocomposites were synthesized with BaTiO₃ nanowires (filler) and poly(vinylidene fluoride) (PVDF) (matrix), and the piezoelectric performances of the composites were systematically studied by varying the aspect ratio (AR) and volume fraction of the nanowire and poling time. BaTiO₃ nanowires with AR of 18 were synthesized and incorporated into PVDF to improve the piezoelectric performance of the composites. It was found that high AR significantly increased the dielectric constant up to 64, which is over 800% improvement compared to those from the composites containing spheroid shape BaTiO₃ nanoparticles. In addition, the dielectric constant and piezoelectric coefficient were also enhanced by increasing the concentration of BaTiO₃ nanowires. The piezoelectric coefficient with 50-vol% BaTiO₃ nanowires embedded in PVDF displayed 61 pC/N, which is much higher than nanocomposites with spheroid shape BaTiO₃ nanoparticles as well as comparable to, if not better, other nanoparticle-filled polymer composites. Our results suggest that it is possible to fabricate nanocomposites with proper mechanical and piezoelectric properties by utilizing proper AR fillers.     

Improved thermo-oxidative stability of three-dimensional and four-directional braided carbon fiber/epoxy hierarchical composites using graphene-reinforced gradient interface layer

In order to improve the thermo-oxidative stability of three-dimensional and four-directional braided carbon fiber/epoxy composites, we introduced a gradient interphase reinforced by graphene nanoplatelets (GN) between the carbon fiber and the matrix, with a liquid phase deposition strategy. Both the interlaminar shear strength and the flexural strength of the composites were improved after thermo-oxidative aging at 140 °C for various durations (up to 1200 h). The interfacial reinforcing mechanisms are explored by analyzing the structure of the interfacial phase, thermal conductivity, weight loss, surface topography, fiber/matrix interfacial morphology and thermomechanical properties of the composites. Results indicate that the GN-reinforced gradient interphase provides an effective shield against interface oxidation, assists in thermal stress transfer, and restricts the movement of the different phases of materials at the composite interface.     

Properties of flame‐retardant TPU based on para‐aramid fiber modified with iron diethyl phosphinate

In this paper, a new type of flame retardant (AF‐Fe) based on para‐aramid fiber (AF) which was modified with iron diethyl phosphinate was applied for thermoplastic polyurethane elastomer (TPU). The flame‐retardant properties of TPU were tested using cone calorimeter test, smoke density test, and thermogravimetric analysis/infrared spectrometry. The cone calorimeter test showed that AF‐Fe can greatly reduce the heat release rate, total heat release, smoke factor, and other parameters of TPU composites compared with the sample of TPU/AF. For example, the pHRR of the composite with 1.0 wt% AF‐Fe was reduced by 15.19% compared with the sample with the same content of pure AF. In addition, the smoke factor of TPU/AFFe3 was reduced by 50.52% and 15.63% compared with TPU0 and TPU/AF respectively. The results of smoke density test showed that the luminous flux of TPU/AFFe3 was increased by 79.26% compared with the sample of TPU/AF. The TG results revealed that the sample with TPU/AFFe3 had lower weight loss rate and higher char residue content at 700°C compared with the sample of TPU/AF.     

Investigations on the structural,mechanical, thermal,and electrical properties of Ce-doped TiO2/poly(n-butyl methacrylate) nanocomposites

This study focused on the fabrication of poly(n-butyl methacrylate) (PBMA) nanocomposites with various concentrations of cerium-doped titanium dioxide (Ce–TiO₂) nanoparticles via in situ polymerization technique. The structural characterization and the material properties of all the composites were analyzed by UV–visible, FTIR, XRD, SEM, DSC, TG, and tensile strength measurements. The UV–visible and FTIR studies confirmed the effective inclusion of Ce–TiO₂ nanoparticles into the PBMA matrix. The change in amorphous morphology of PBMA to a crystalline structure was observed from the XRD pattern. The SEM morphology revealed the attachment of nanoparticles in the polymer matrix. The inclusion of Ce–TiO₂ nanoparticles enhanced the glass transition temperature, and thermal stability of the PBMA matrix was revealed from DSC and TG, respectively. The tensile strength of PBMA was greatly enhanced by the addition of Ce–TiO₂ nanoparticles. The AC conductivity, dielectric constant, and dielectric loss studies were also performed in the frequency range 10²–10⁶ Hz, and it was observed that addition of Ce–TiO₂ nanoparticles greatly enhanced the electrical properties of PBMA. The change in dielectric constant with the addition of nanoparticles was correlated with a theoretical modeling study. This work also extended to study the role of Ce–TiO₂ nanoparticles in the reinforcing mechanism of the nanocomposite by comparing the actual tensile strength of the composite with different theoretical modeling. The high dielectric constant and tensile strength of composite are beneficial in designing lightweight and highly efficient nanoelectronic materials based on the family of polybutyl acrylates.

     

The thermal and dielectric properties of high performance cyanate ester resins/microcapsules composites

Novel high performance bisphenol A dicyanate ester (BADCy) resins/poly(urea-formaldehyde) microcapsules filled with epoxy resins (MCEs) composites have been prepared. The effects of different contents of MCEs on the thermal and dielectric properties of cured BADCy were investigated using dynamic mechanical analyzer (DMA), thermalgravimetric analyzer (TGA) and broadband dielectric analyzer. The dielectric properties of BADCy/MCEs treated in hot water and hot air were also discussed. The morphologies of BADCy/MCEs composites were characterized by scanning electron microscopy (SEM). Results indicate that the appropriate content of MCEs can improve or maintain the thermal stability, the low dielectric constant and dielectric loss of cured BADCy mainly owing to higher conversion of cyanate ester (-OCN) groups. After aged in hot water and hot air, respectively, BADCy/MCEs composites with small content of MCEs can retain the low dielectric constant and dielectric loss.     

Preparation and properties of an efficient smoke suppressant and flame‐retardant agent for thermoplastic polyurethane

APP@ETA, as a new type of flame retardant, was prepared by chemically modifying ammonium polyphosphate (APP) with ethanolamine (ETA) and applied to thermoplastic polyurethane (TPU) in this study. Then, the smoke suppression properties and flame‐retardant effects of APP@ETA in TPU composites were evaluated using smoke density test, cone calorimeter test, etc. And, the thermal degradation properties of flame‐retardant TPU composites were investigated by thermogravimetric analysis/infrared spectrometry. The smoke density test results indicated that APP@ETA could obviously improve the luminous flux of TPU composites in the test with or without flame. The cone calorimeter test results showed that total smoke release, smoke production rate and smoke factor of the composites with APP@ETA were significantly decreased than those of the composites with APP. For example, when the loading of APP@ETA or APP was 12.5 wt%, the total smoke release of the sample with APP@ETA decreased to 3.5 m²/m² from 6.0 m²/m², which was much lower than that of the sample with APP, reduced by 41.7%. The thermogravimetric analysis results demonstrated that APP@ETA could decrease the initial decomposition temperature and improve the thermal stability at high temperature for TPU composites. Copyright © 2017 John Wiley & Sons, Ltd.     

An interlayer model for the complex dielectric constant of composites: An extension to ellipsoidally shaped particles

A theoretical interlayer model (IL) has been developed for the complex dielectric constant of a composite in which the filler particles are enveloped with a layer of interfacial material. The filler particles can be of any ellipsoidal shape. Special cases such as spherical particles, needles, and fabrics are shown to be covered by the model.The analytical formula as derived describes the composite properties as a function of the volume fractions of the filler, the layer and the matrix material, their dielectric properties and the filler particle shape factor.In the case of a two-phase composite the model reduces to the well-known Sillars relation for the complex dielectric constant of composite which contains filler particles of ellipsoidal shape.The effect of an interfacial layer on the static dielectric constant of the composite is discussed using the model. Next, the special case of a conductive interfacial layer in an otherwise non-conductive composite is discussed; it illustrates the effect of interfacially adsorbed water on the electrical properties of composites. Some practical examples are shown.