Synthesize procedures, mechanical and thermal properties of thiazole bearing poly(amid-imide) composite thin films containing multiwalled carbon nanotubes

This research is aimed at characterizing the thermal, mechanical, and morphological properties of carbon nanotubes (CNTs) reinforced poly(amide-imide) (PAI) composites having thiazol and amino acid groups which were prepared by sonication-assisted solution compounding. To increase the compatibility between the PAI matrix and CNTs, carboxyl-functionalized multiwall CNTs (MWCNTs-COOH) were used in this study. The MWCNTs were dispersed homogeneously in the PAI matrix while the structure of the polymer and the MWCNTs structure are stable in the preparation process as revealed by transmission electron microscopy. MWCNT/PAI composite films have been prepared by casting a solution of precursor polymer containing MWCNTs into a thin film, and its tensile properties were examined. The thermal stability, Young’s modulus, and tensile strength of PAI were greatly improved by the incorporation of MWCNTs and their good dispersion. Composites were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and thermal gravimetric analysis.     

Strengthening of liquid crystalline polymer by functionalized carbon nanotubes through interfacial interaction and homogeneous dispersion

Multiwalled carbon nanotubes (MWCNTs) were functionalized with two types of chemical moieties (i.e. carboxylic, ? COOH and hydroxyl benzoic acid groups, ‐HBA) on their sidewalls in order to improve their interaction with a liquid crystalline polymer (LCP) and dispersion in LCP. We have investigated the rheological, mechanical, dynamic mechanical, and thermal properties in detail with variation of HBA‐functionalized MWCNTs in the LCP matrix. Effect of the dispersion state of the functionalized MWCNTs in the LCP matrix on the rheological behavior was also studied. The composites containing HBA‐functionalized MWCNTs showed higher complex viscosity, storage, and loss modulus than the composites with the same loading of raw MWCNTs and MWCNT‐COOH. It was suggested that the HBA‐functionalized MWCNTs exhibited a better dispersion in the polymer matrix and formed stronger CNT‐polymer interaction in the composites than the raw MWCNTs and MWCNT‐COOH, which was also confirmed by FESEM and FTIR studies. As a result, the overall mechanical performance of the HBA‐MWCNT‐LCP composites could be improved significantly. For example, the addition of 4 wt% HBA‐MWCNT to LCP resulted in the considerable improvements in the tensile strength and modulus of LCP (by 66 and 90%, respectively). Copyright © 2010 John Wiley & Sons, Ltd.     

碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

Effect of acid treated multi-walled carbon nanotubes on the mechanical, permeability, thermal properties and thermo-oxidative stability of isotactic polypropylene

The effect of acid treatment of multi-walled carbon nanotubes (MWCNTs) on the mechanical, thermal and mainly thermo-oxidative stability of isotactic polypropylene (iPP) was evaluated. From the acid treatment surface carboxylic groups were mainly formed, while the nanotubes' length was gradually reduced by increasing the treatment time. Young's modulus, tensile strength and storage modulus of the iPP/MWCNT nanocomposites were increased by increasing the treatment time of the MWCNTs, due to finer dispersion inside the polymer matrix, as revealed by TEM and micro-Raman spectroscopy. Furthermore, the nanotubes acted as nucleating agents, an effect more pronounced with finer filler dispersion. Thermal stability in an inert atmosphere also increased. Thermo-oxidative stability tests in air and O₂ revealed that oxidative degradation took place in two stages. In the first stage, corresponding to temperatures up to 230 °C, the MWCNTs accelerated the oxidation of iPP, while at higher than 300 °C temperatures the trend was reversed. Incubation studies proved that, at the first stages, oxidation was due to random chain scission of iPP and oxygen uptake. This behaviour was accelerated by the MWCNTs' surface carboxylic groups and, as found by O₂ permeability studies, was mainly a surface process. In the second stage, due to the shielding effect of MWCNTs, the removal of the gases produced during decomposition was hindered. At this stage the presence of MWCNTs resulted in more thermo-oxidatively stable nanocomposites.     

Crystallization Behavior and Mechanical Properties of Poly(vinylidene fluoride)/multi-walled Carbon Nanotube Nanocomposites

Poly(vinylidene fluoride)(PVDF)/multi-walled carbon nanotube(MWCNT) nanocomposites were prepared by means of ultrasonic dispersion method. X-ray diffraction(XRD) results indicate that incorporating MWCNTs into PVDF caused the formation of β phase. A thermal annealing at 130 °C confirmed that the β phase was stable in the nanocomposites. Differential scanning calorimetry(DSC) results indicate that the melting temperature slightly increased while the heat of fusion markedly decreased with increasing MWCNT content. The tensile strength and modulus of PVDF were improved by loading the MWCNTs. The scanning electron microscopy(SEM) observations showed that MWCNTs were uniformly dispersed in the PVDF matrix and an interfacial adhesion between MWCNT and PVDF was achieved, which was responsible for the enhancement in the tensile strength and modulus of PVDF.     

Development of Natural Rubber-Fibrous Nano Clay Attapulgite Composites: The Effect of Chemical Treatment of Filler on Mechanical and Dynamic Mechanical Properties of Composites

Common nano clay fillers have layered structure. Some nano clays like Attapulgite (AT), Sepiolite have rod like fibrous structure. Compared to layered structured clay fibrous clay AT can undergo better dispersion in polymer matrix leading to better improvement in composite properties. Chemical modifications of AT are done through amine treatment as well as by amine+silane treatment to get chemically modified fillers AAT and SAT respectively. In the present investigation, nano composites are prepared using natural rubber (NR) filled with AT, AAT and SAT. Three different loadings of each filler are used namely 2.5, 5, and 10 phr (parts per hundred of rubber). Mechanical properties like tensile strength, elongation at break increase with the increase in filler loading up to 5 phr there after these properties marginally fall when loading is increased to 10 phr due to problem of filler dispersion at higher loading. However, modulus at 300% elongation and tear strength increases with the increase in filler loading up to 10 phr. Very similar trend can also be observed for composites with chemically modified fillers, AAT and SAT. But the degree of reinforcement is higher in the case of AAT and SAT compared to that of unmodified filler AT for the same filler loading. This difference is mainly due to better polymer-filler interaction and filler dispersion in the case of chemically modified clays AAT and SAT compared to unmodified AT. Tear strength of composites increases remarkably with the addition of AT and which is further enhanced when chemically modified clays AAT and SAT are added. Dynamic-mechanical analyses of different clay composites give idea about the difference in the degree of polymer–filler interaction due to chemical treatment of filler.     

Effect of sol-gel derived nano-silica and organic peroxide on the thermal and mechanical properties of low-density polyethylene/wood flour composites

The influence of nano-silica, synthesized and mixed with low-density polyethylene (LDPE) through a sol-gel process, on the thermal and mechanical properties of LDPE and LDPE/wood flour (WF) composites, prepared in the absence and presence of dicumyl peroxide, was investigated. Scanning electron microscopic (SEM) analyses show a uniform dispersion of silica nano-particles of size 10-50 nm in the matrix, and Fourier-transform infrared (FTIR) spectroscopic results indicated interaction between the nano-silica and the LDPE matrix, which seems to improve for samples prepared in the presence of dicumyl peroxide (DCP). WF and nano-silica, as well as the presence of DCP during sample preparation, substantially improve the thermal stability of the LDPE matrix. The tensile strength of the samples decreased with increasing wood flour content, while the tensile modulus substantially increased. The presence of nano-silica gave rise to lower values for both tensile strength and tensile modulus, while higher tensile strength (and an increase in tensile strength with WF content) is observed for samples prepared in the presence of DCP. The tensile modulus increases with increasing WF content, but is not substantially influenced by the presence of nano-silica or by sample preparation in the presence of DCP. The DMA results were in line with the tensile results.     

Nanotubes as polymer composite reinforcing additive materials – A comparative study

Nitrogen-doped bamboo-shaped carbon nanotubes (N-BCNTs) and their non-doped conventional counterparts, multiwalled carbon nanotubes (MWCNTs) were compared as polymer reinforcing additives in polyvinyl chloride (PVC) matrix. The nanotubes were synthetized by catalytic chemical vapor deposition (CCVD) method. The purity of both nanotubes was measured by thermogravimetric analysis (TGA) and found to be >91%. Further analysis on the morphology and size of the carbon nanotubes (CNTs) were performed by transmission electron microscopy (TEM). The PVC powder was impregnated with CNTs in ethanol by using tip ultrasonicator. The dispersion media was evaporated, and the CNT/PVC powder was used to produce polymer fibers. The orientation of carbon nanotubes in the PVC matrix was characterized by scanning electron microscopy (SEM), and the presence of nanotubes were confirmed in case of all PVC samples. It can be observed on the SEM images that the nanotubes are fully covered with PVC. The tensile strength of the nanotube containing samples was tested and the N-BCNT/PVC composite was found to be better in this sense, thanks to the extraordinary structure of the nanotube. In case of the N-BCNT/PVC composite the measured young modulus was 39.7% higher, while the elongation at brake decreased by 33.6% compare to the MWCNT/PVC composite. These significant differences in the mechanical properties of the composites can be explained with the stronger interaction between N-BCNTs and PVC.     

Preparation of polymer nanocomposites with enhanced mechanical properties using hybrid of graphene and partially wrapped multi-wall carbon nanotube as nanofiller

Triblock copolymer of poly(p-dioxanone) and polyethylene glycol end-capped with pyrene moieties ((Py-PPDO)₂-b-PEG) was synthesized and used as modifier for multi-wall carbon nanotubes (MWCNTs). Nano-aggregates ((Py-PPDO)₂-b-PEG@MWCNTs) with shish-kebab like partially wrapped morphology and very good stability were obtained by incorporating the copolymer with MWCNTs. The bare MWCNT sections of (Py-PPDO)₂-b-PEG@MWCNTs were able to induce π-π interactions with graphene (GE) and resulted in a novel GE/(Py-PPDO)₂-b-PEG@MWCNTs hybrid. The dispersity of GE in solution or polymer matrix was therefore greatly improved. The PCL nanocomposite films using GE/(Py-PPDO)₂-bPEG@MWCNTs as hybrid nanofiller exhibited obviously improved mechanical properties especially at very low hybrid nanofiller content. The influence of the nanofiller content and feed ratio of GE/MWCNTs on the mechanical properties of composites films was evaluated. When the feed ratio of GE to MWCNTs is 2:8 and the total loading of nanofiller is only 0.01 wt%, the tensile strength of the composite film increased by 163% and the elongation at break increased by 17% compared to those of neat PCL. These results can be attributed to fine dispersion of the nanofillers in PCL matrix and the hybrid interactions between GE and MWCNTs. Therefore, this work provides a novel method for preparing polymer nanocomposites with high mechanical performance and low nanofiller loading.     

Structure and performance of nano-hydroxyapatite filled biodegradable poly((1,2-propanediol-sebacate)-citrate) elastomers

Novel nano-hydroxyapatite (n-HAp)/poly((1,2-propanediol-sebacate)-citrate) (PPSC) composites, with varying the amount of n-HAp (5–20 wt%), for potential use in the soft tissue engineering were developed in the present work. The structure of composites was characterized by FT-IR and ¹³C NMR, the micromorphology of n-HAp and the dispersion property of n-HAp in n-HAp/PPSC composites were characterized by SEM and TEM. The experimental results showed that no obvious chemical bonds generated between n-HAp and PPSC matrix. Homogeneous distribution of nanoparticles in the polymer matrix was validated. DSC and DMA indicated that the Tg of the composites decreased with increasing the n-HAp content, as the chemical cross-linking density of the composites decreased. The mechanical properties of the composites were prominently improved, when the amount of n-HAp increased up to 20 wt%, the modulus of the composites increased 11.4 times, and the tensile strength of the composites increased 8.2 times. The hydrophilicity, water absorption, and degradation rate of composites can be tuned through varying the concentration of n-HAp. In vitro cytotoxicity was evaluated by the MTT assay with the L929 cell. The cell relative growth rates of the composites with the amount of n-HAp more than 10 wt% exceeded 75% after 7 days of incubation.     

Dissolution of MWCNTs by using polyoxadiazoles,and highly effective reinforcement of their composite films

Nonmodified multiwalled carbon nanotubes (MWCNTs)/sulfonated polyoxadiazole (sPOD) nanocomposites are successfully prepared by a facile solution route. The pristine MWCNTs are dispersed in a sPOD solution, and the mixtures are fabricated into thin films by solution casting. The homogeneous dispersion of nanotubes in the composites is confirmed by transmission electron microscopy. The mechanical properties, thermal stability, and electrical conductivity are investigated. Tensile strength, elongation at break, and tensile energy to break are shown to increase by more than 28, 45, and 73%, respectively, by incorporating up to 1.0 wt % pristine MWCNTs. The experimental values for sPOD/MWCNTs composite stiffness are compared with Halpin‐Tsai and modified Halpin‐Tsai predictions. The storage modulus is found to increase up to 10% at low CNT loading. The composite films, which have an outstanding thermal stability, show an increase of up to 57 °C in the initial degradation temperature. The addition of 1.0 wt % MWCNTs increases the electrical conductivity of the sPOD matrix by two orders of magnitude. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Bio-Based Nanocomposites of Cellulose Acetate and Nano-Clay with Superior Mechanical Properties

Summary: Bio-based nanocomposites were manufactured by melt intercalation of nanoclays and cellulose acetate (CA) with and without plasticizer. Glycerol triacetate (triacetin) as plasticizer up to 30 mass%, and different types of organo-modified and unmodified montmorillonites (MMTs) as filler were used. X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM), were used to study clay dispersion, intercalation/exfoliation, and structure of the composites. XRD and TEM revealed very good dispersion and exfoliation of modified clay throughout the CA matrix. While for unmodified clay agglomeration and poor dispersion but an intercalated structure was observed. The mechanical properties of injection moulded test bars were determined by a tensile experiment giving tensile strength, Young's modulus and elongation at break. Adding plasticizer facilitated the processing and up to 20 mass%, increased the tensile strength, Young's modulus and elongation at break as well. Higher amount of plasticizer diminished the tensile properties except elongation showing a slight increase. In all plasticized composites, organo-modified clay improved the tensile strength and at the same time, young's modulus and elongation almost remained constant. On the other hand, plasticized CA compounded with unmodified clay revealed lower properties. In a particular case, compounding of unplasticized CA with unmodified clay resulted in superior mechanical properties with a novel structure. So that, in optimum percentage –5 mass%- of unmodified clay, tensile strength and young's modulus increased significantly by 335% and 100%, to 178 MPa and 8.4 GPa, respectively. This is a dramatic improvement in strength and stiffness of CA. Adding organo-modified clay resulted in a little improvement in tensile properties. SEM pictures of the optimum composite showed a core/shell structure with high orientation in the shell part. It is supposed that this behaviour is caused by the interaction between CA hydroxyl groups and free cations existing in the galleries of unmodified clay.     

Experimental and modeling analysis of mechanical-electrical behaviors of polypropylene composites filled with graphite and MWCNT fillers

The incorporation of carbon fillers can improve the thermal and electrical conductivities of polymer composites but will also have a significant effect on the flexural and tensile behavior. In this paper, two types of carbon fillers were added to polypropylene - carbon nanotubes and synthetic graphite. The influences of these filler materials on the tensile, flexural and fracture toughness characteristics were measured and the electrical conductivity of composites was also investigated. It was observed that the fillers lead to a remarkable increase in the flexural and tensile modulus of polypropylene composites. The maximum flexural and tensile strengths slightly increased with the addition of graphite, however, they were significantly increased in the case of carbon nanotubes because MWCNTs possess exceptional stiffness and strength and their length to diameter ratio is extremely high when compared with graphite. Electrical conductivity of polypropylene composites was evaluated. Noteworthy, composites based on synthetic graphite show a percolation process at one order of magnitude concentration higher than MWCNT filled polypropylene. Fracture toughness results open a wide range of applications for PP-MWCNT composites. Several prediction models were inspected in this research and it was concluded that inverse rule of mixtures model showed the most accurate predictions of the tensile modulus for composites made of polypropylene.     

CaCO3/PEEK复合体系的力学行为和热行为研究

以聚醚醚酮和碳酸钙复合体系为研究对象,考察了偶联剂和填料添加量对复合材料力学行为和热行为的影响.发现磺化聚醚醚酮作为偶联剂能有效地改善材料的力学性能,提高基体树脂的玻璃化转变温度,降低基体树脂的熔点,有助于改善聚醚醚酮的加工条件     

Fiber property and structure development of polyester blend fibers reinforced with a thermotropic liquid‐crystal polymer

Ternary blend fibers (TBFs), based on melt blends of poly(ethylene 2,6‐naphthalate), poly(ethylene terephthalate), and a thermotropic liquid‐crystal polymer (TLCP), were prepared by a process of melt blending and spinning to achieve high‐performance fibers. The reinforcement effect of the polymer matrix by the TLCP component, the fibrillar structure with TLCP fibrils of high aspect ratios, and the development of more ordered and perfect crystalline structures by an annealing process resulted in the improvement of the tensile strength and modulus for the TBFs. An increase in the apparent crystallite size with the spinning speed was attributed to the development of larger crystallites and more ordered crystalline structures in the annealed TBFs. The birefringence and density of the TBFs increased with increasing spinning speed, the TBFs becoming more oriented and the crystal packing becoming more enhanced. The molecular orientation was an important factor in determining the tensile strength and modulus of the TBFs. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 395–403, 2004     

The mechanical and electrical properties of carbon nanotube‐grafted polyimide nanocomposites

Polyimide (PI)‐based nanocomposites containing aminophenyl functionalized multiwalled carbon nanotubes (AP‐MWCNTs) obtained through a diazonium salt reaction was successfully prepared by in situ polymerization. PI composites with different loadings of AP‐MWCNTs were fabricated by the thermal conversion of poly(amic acid) (PAA)/AP‐MWCNTs. The mechanical and electrical properties of the AP‐MWCNTs/PI composites were improved compared with those of pure PI due to the homogeneous dispersion of AP‐MWCNTs and the strong interfacial covalent bonds between AP‐MWNTs and the PI matrix. The conductivity of AP‐MWNTs/PI composites (5:95 w/w) was 9.32 × 10^?1 S/cm which was about 10¹⁵ times higher than that of Pure PI. The tensile strength and tensile modules of the AP‐MWCNTs/PI composites with 0.5 wt % of AP‐MWCNTs were increased by about 77% (316.9 ± 10.5 MPa) and 25% (8.30 ± 1.10 GPa) compared to those of pure PI, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 960–966     

Fabrication of Single Wall Carbon Nanotubes-Based Poly(vinyl butyral) Nanocomposites with Enhanced Mechanical and Thermal Properties

In this research, poly(vinyl butyral) (PVB)/single wall carbon nanotubes (SWCNT) composites were prepared via solution blending method. Dispersion degree of SWCNT in the composites was characterized by Scanning Electron Microscopy (SEM) and mechanical properties were measured with tensile testing. Thermal degradation of composites was investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). SEM analysis confirmed good dispersion of the nanotubes in the PVB. The tensile tests showed significant increases in mechanical properties such as exceptional improvement in tensile strength, Young's modulus and flexibility for the composites compared to PVB at low SWCNT content.The TGA curves indicated that adding SWCNT improved the thermal stability of the PVB significantly and the degradation of the polymer matrix shifted to the higher temperatures. For the sample containing 0.6 wt%, an increase of 171% in modulus and a 258.4% enhancement of tensile strength were achieved. Also, elongation at break increased 28.7% at this loading. In fact, intrinsic properties of nanotubes caused enhancement of strength and flexibility simultaneously. Also, for this composite, T_onset and T_max enhanced remarkably and weight loss reduced greatly and residue at 600°C increased to high values. These results are promising for application of the PVB in industry.     

Morphology of a phase-separated and a molecular composite PBT/ABPBI polymer blend

The structure and morphology of homopolymers and blends of rigid-rod poly(p-phenylene benzobisthiazole) (PBT) and semiflexible coil poly[2,5(6)benzimidazole] (ABPBI) were examined by wide-angle x-ray diffraction and scanning and transmission electron microscopy. When samples were processed from a solution where the total polymer concentration of 30% PBT/70% ABPBI blend was greater than a critical concentration, large-scale phase separation occurred and 0.1–4 μm ellipsoidal particles were present in a ductile matrix. The ellipsoids were chiefly composed of aggregates of well-oriented 10-nm PBT crystallites, while the matrix material was chiefly ABPBI. When the concentration was less than a critical concentration, the solution was optically homogeneous. In processing of fiber and film samples from the homogeneous solution, large-scale phase separation was inhibited by rapid coagulation in a water bath. After heat treatment, these samples were found to contain crystallites of both PBT and ABPBI with lateral dimensions of ordered regions no larger than 3 nm. The PBT homopolymer was dispersed in the matrix at the molecular level in ordered regions at a scale no larger than 3 nm, resulting in a rigid-rod molecular composite. In the rigid-rod molecular composite fiber both the molecular-level dispersion and high orientation contributed to higher values of strength and modulus compared to the properties of a phase-separated fiber. The strength and modulus of highly oriented fiber were only 25% higher than those of planar isotropically oriented film, suggesting that the level of dispersion of rod molecules is more important than orientation of the reinforcing phase in rigid-rod molecular composites.     

Effect of on-line ultrasonic treatment on the properties of carbon fiber reinforced plastic composites

The strength, performance, and application of carbon fiber reinforced plastic (CFRP) composites are directly affected by the interfacial bonding between fiber and resin. Wet winding technology is a commonly used composite productive process, and improving interfacial bonding of composites by on-line treatment has always been the focus of attention. In this paper, an on-line ultrasonic treatment system is designed and realized, the resin content of prepregs is determined by the dissolution method; standard deviation and dispersion coefficient are also calculated. The surface morphology, internal structure of prepregs, and the component of resin are observed and analyzed using a Metallurgical Microscope, scanning electron microscope (SEM), and near infrared radiation spectra (NIRS). The strength and performance of prepregs [(tensile strength, bending strength, tensile modulus of elasticity, bending modulus of elasticity, and interlaminar shear strength (ILSS)] are also tested. The results show the on-line ultrasonic treatment system can effectively improve the interfacial bonding of CFRP composites and enhance the strength and performance of CFRP composites.     

掺杂羧基化碳纳米管的纳米碳纤维前驱体的制备及表征

为获得结构完整、 性能优良的纳米碳纤维前驱体, 采用静电纺丝法制备了掺杂羧基化多壁碳纳米管(MWCNTs)的聚丙烯腈(PAN)纳米纤维. 用扫描电子显微镜、 偏振红外光谱、 透射电子显微镜、 拉曼光谱及拉伸性能测试等对杂化纳米纤维的微观结构和力学性能进行了研究, 分析了MWCNTs含量的影响. 实验结果表明, 5%(质量分数)的MWCNTs掺杂量为杂化纳米纤维直径的突变点, 且MWCNTs的加入有利于PAN分子链的取向, MWCNTs在PAN纤维中大体上沿纤维轴向取向分布. 3%MWCNTs/PAN杂化纳米纤维的拉伸强度和拉伸模量分别达到88.6 MPa和3.21 GPa.