Influence of electron beam irradiation on physicochemical properties of poly(trimethylene carbonate)

Electron beam (EB) irradiation of poly(trimethylene carbonate) (PTMC), an amorphous, biodegradable polymer used in the field of biomaterials, results in predominant cross-linking and finally in the formation of gel fraction, thus enabling modification of physicochemical properties of this material without significant changes in its chemical structure. PTMC films (M_w: 167-553 kg mol⁻¹) were irradiated with different doses using an electron accelerator. Irradiation with a standard sterilization dose of 25 kGy caused neither significant changes in the chemical composition of the polymer nor significant deterioration of its mechanical properties. Changes in viscosity-, number-, weight-, and z-average molecular weights of PTMC for doses lower than the gelation dose (D_g) as well as gel-sol analysis and swelling tests for doses above D_g indicate domination of cross-linking over degradation. EB irradiation can be considered as an effective tool for increasing the average molecular weight of PTMC and sterilization of PTMC-based biomaterials.     

Y‐shaped poly(ethylene glycol) and poly(trimethylene carbonate) amphiphilic copolymer: Synthesis and for drug delivery

New Y‐shaped (AB₂‐type) amphiphilic copolymers of poly(ethylene glycol) (PEG) with poly(trimethylene carbonate) (PTMC), PEG‐b‐(PTMC)₂, were successfully synthesized by the ring‐opening polymerization (ROP) of TMC with bishydroxy‐modified monomethoxy‐PEG (mPEG). First, a bishydroxy functional ROP initiator was synthesized by esterification of acryloyl bromide with mPEG, followed by Michael addition using excess diethanolamine. A series of Y‐shaped amphiphilic PEG‐(PTMC)₂ block copolymers were obtained via ROP of TMC using this PEG with bishydroxyl end groups as macroinitiator and ZnEt₂ as catalyst. The amphiphilic block copolymers with different compositions were characterized by gel permeation chromatography (GPC) and ¹H NMR, and their molecular weight was measured by GPC. The results showed that the molecular weight of Y‐shaped copolymers increased with the increase of the molar ratio of TMC to mPEG‐(OH)₂ initiator in feed while the PEG chain length was kept constant. The Y‐shaped copolymer mPEG‐(PTMC)₂ could self‐assemble into micelles in aqueous medium and the critical micelle concentration values of the micelles decrease with increase in hydrophobic PTMC block length of mPEG‐(PTMC)₂. The in vitro cytotoxicity and controlled drug release properties of the Y‐shaped amphiphilic block copolymers were also investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8131–8140, 2008     

New fluorinated oxazoline block copolymer lowers the adhesion of platelets on polyurethane surfaces

We have prepared an amphiphilic oxazoline block copolymer of hydrophilic poly(2-methyl-2-oxazoline) and hydrophobic poly[2-(2-perfluorooctyl)ethyl-2-oxazoline] chains. By controlling the length and composition of polymer chains, we found that this fluorinated block copolymer can be readily dissolved in water. Furthermore, we can achieve a stable surface coating of the fluorinated block copolymer by dissolving the copolymer in water, then coating the aqueous copolymer solution onto surfaces of nonwater-soluble polymers. This is a simple and useful method of modifying the surface character of polymer substrates. We have found that the polyether urethane (PEU) coated by block copolymer has a different surface chemistry and biological reactivity than the uncoated PEU. From XPS analysis, we found the fluorinated copolymer was coated on PEU (atomic % of F: 31.3 on coated PEU, 0.3 on uncoated). The two surfaces have different affinities for biological molecules. Specifically, the fibrinogen adsorption on the fluorinated copolymer-coated PEU was 62 ± 39 ng/cm², compared to a value of 156 ± 99 ng/cm² for uncoated PEU. In an ex vivo evaluation of platelet adhesion, the surface of coated PEU attached a few white cells while uncoated PEU was covered with activated platelets. © 1994 John Wiley & Sons, Inc.     

Electrochemical storage properties of polyaniline-, poly(N-methylaniline)-, and poly(N-ethylaniline)-coated pencil graphite electrodes

Three types of conducting polymers, polyaniline (PANI), poly(N-methylaniline) (PNMA), poly(N-ethylaniline) (PNEA) were electrochemically deposited on pencil graphite electrode (PGE) surfaces characterized as electrode active materials for supercapacitor applications. The obtained films were electrochemically characterized using different electrochemical methods. Redox parameters, electro-active characteristics, and electrostability of the polymer films were investigated via cyclic voltammetry (CV). Doping types of the polymer films were determined by the Mott-Schottky method. Electrochemical capacitance properties of the polymer film coating PGE (PGE/PANI, PGE/PNMA, and PGE/PNEA) were investigated by the CV and potentiostatic electrochemical impedance spectroscopy (EIS) methods in a 0.1 M H₂SO₄ aqueous solution. Thus, capacitance values of the electrodes were calculated. Results show that PGE/PANI, PGE/PNMA, and PGE/PNEA exhibit maximum specific capacitances of 131.78 F g^?1 (≈ 436.50 mF cm^?2), 38.00 F g^?1 (≈ 130.70 mF cm^?2), and 16.50 F g^?1 (≈ 57.83 mF cm^?2), respectively. Moreover, charge-discharge capacities of the electrodes are reported and the specific power (SP) and specific energy (SE) values of the electrodes as supercapacitor materials were calculated using repeating chronopotentiometry.     

Photoelectrochemical effect with poly(p-phenylene sulfide) films

Poly(p-phenylene sulfide) films coated on conducting SnO₂ and Pt surfaces were found to attain p-type semiconducting properties on electrochemical cycling. Upon illumination of these films with visible light (λ < 500 nm) a photoelectrochemical effect was observed. The performance of a photoelectrochemical cell employing this polymer film coated electrode is discussed.     

Water vapour barrier performance of corn-zein coated polypropylene (PP) packaging films

The novel film structure of corn-zein coated on polypropylene (PP) synthetic film for packaging industry was developed to examine the feasibility of resulting coated films as an alternative water barrier performance for food packaging. The effects of coating formulation (solvent, corn-zein, plasticizer concentration and plasticizer type) on final properties of films were observed. Corn-zein is the most important protein of corn and has good film forming property. Composites structures of PP films coated with corn-zein were obtained through a simple solvent casting method. Polyethylene glycol (PEG) and glycerol (GLY) were used as plasticizer to increase film flexibility. Statistical analysis based on full factorial design was performed to observe coating formulation effects. The high water vapour barriers were obtained for films coated with coating formulation consisting of higher amounts of corn-zein plasticized by GLY. The lower glass transition temperatures (T _g) of films were obtained by plasticization of films and T _g decreased by increasing plasticizer content. The statistical analysis defined the key parameters of coating formulation that had major effects on the final properties of coated PP films as corn-zein, plasticizer concentration and plasticizer type. In conclusion, corn-zein coatings could have potential as an alternative to conventional synthetic polymers used in composite multilayer structures for food packaging applications.     

H型(PS)2PEG(PS)2嵌段共聚物在旋涂过程中的结晶行为

采用原子力显微镜和X射线衍射等手段研究了H型(PS)₂PEG(PS)2嵌段共聚物在不同溶剂和不同浓度的溶液中旋涂所得薄膜的形貌, 并与聚乙二醇(PEG)均聚物进行了比较. 虽然(PS)₂PEG(PS)₂中PS的链长很短, 但对形貌有很大影响, PS链段的存在改变了聚合物在基底上的稳定性, 使用四氢呋喃为溶剂, 当溶液浓度较小时, 在旋涂过程中发生去润湿, 然后再发生结晶, 膜厚较大时去润湿被抑止, 所得形貌与PEG均聚物类似. 以甲苯为溶剂时, 由于PEG和PS与溶剂的相互作用不同, 共聚物在溶液中形成胶束, 从而改变了聚合物的结晶形貌.     

Synthesis and characterization of ABA-type block copolymer of poly(trimethylene carbonate) with poly(ethylene glycol): Bioerodible copolymer

ABA-type block copolymers of poly(trimethylene carbonate) with poly(ethylene glycol) (M_n 6820), PTMC-b-PEG-b-PTMC, were synthesized by the ring-opening polymerization of 1,3-dioxan-2-one (trimethylene carbonate) in the presence of poly-(ethylene glycol) with stannous octoate catalyst, and the copolymers with various compositions were obtained. The PTMC-b-PEG-b-PTMC copolymers were characterized with Fourier transform infrared and nuclear magnetic resonance spectroscopies. The intrinsic viscosities of resulting copolymers increased with the increase of 1,3-dioxan-2-one content in feed while the molar ratio of monomer over catalyst kept constant. It has been observed that the glass transition temperature (T_g) of the PTMC segments in copolymers, recorded from differential scanning calorimetry, was dependent on the composition of copolymers. The melting temperature (T_m) of PEG blocks in copolymer was lower than that of PEG polymer, and then disappeared as the length of PTMC blocks increased. The results of dynamic contact angle measurement clearly revealed that the hydrophilicity of resulting copolymers increased greatly with the increase of PEG content in copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 695–702, 1998     

Some properties of networks produced by the Diels-Alder reaction between poly(styrene-co-furfuryl methacrylate) and bismaleimide

Poly (styrene-co-furfuryl methacrylate) networks were prepared by the Diels-Alder (D-A) reaction in solution at 25 °C between the linear copolymer and bismaleimide (BM). The resultant crosslinked polymers were swollen to equilibrium in toluene at 25 °C and swelling properties were studied by gravimetric and dimensional measurements. The swelling behaviour of these organogels depended on the composition of the copolymer and the concentration of BM used. Shear and Young’s moduli and the effective crosslinking densities (ν_e) were determined by compression (stress)-strain measurements. The theoretical crosslinking density was higher than the ν_e for all the crosslinked copolymers. An endothermic peak without T_g was observed on the DSC curve on heating the dry crosslinked polymer. On reheating a T_g at ≈98 °C was found, which is attributed to presence of linear copolymer produced by the retro D-A reaction in the first heating. The thermal stability of a crosslinked copolymer under nitrogen and air showed differences with the stability of the linear copolymer. The increase in viscosity of the solution during the D-A reaction was followed with time, for initial linear copolymers of different molecular weights. It was found that onset of gelation increased to longer reaction times the lower the molecular weight of copolymer.     

Enhancing stability of poly(1,3-cyclohexadiene)-based materials by bromination and dehydrobromination

In order to improve their thermal stability, poly(1,3-cyclohexadiene) (PCHD) homopolymer, diblock copolymer of PCHD with styrene (PCHD-b-PS), and crosslinked PCHD membranes were dehydrogenated by addition of bromine to the polymer in solution, followed by dehydrobromination using an isothermal treatment at elevated temperature. The brominated PCHD materials thus obtained were characterized via FT-IR and thermogravimetric analysis (TGA) before and after dehydrobromination. Dehydrobromination was performed inside a TGA instrument, allowing insight into thermal stability of the analytes to be obtained. The dehydrobrominated PCHD samples were characterized using elemental analysis, and it was found the dehydrogenation of PCHD to polyphenylene was not complete. Nevertheless, some aromatization did occur, and the thermal stability of the treated polymer was greatly enhanced as compared to its PCHD precursor. Such materials may thus be of interest as high carbon content, graphene-like films. Crosslinked PCHD membranes and PCHD-b-PS diblock copolymers were treated via the same bromination/pyrolysis process, which resulted in markedly improved thermal stabilities for these materials as well.     

Nucleation activity of nanosized CaCO3 on crystallization of isotactic polypropylene, in dependence on crystal modification, particle shape, and coating

A detailed analysis of the effect of calcium carbonate nanoparticles on crystallization of isotactic polypropylene (iPP) is reported in this contribution. CaCO₃ nanoparticles with different crystal modifications (calcite and aragonite) and particle shape were added in small percentages to iPP. The nanoparticles were coated with two types of compatibilizer (either polypropylene-g-maleic anhydride copolymer, or fatty acids) to improve dispersion and adhesion with the polymer matrix.It was found that the type of coating agent used largely affects the nucleating ability of calcium carbonate towards formation of polypropylene crystals. CaCO₃ nanoparticles coated with maleated polypropylene can successfully promote nucleation of iPP crystals, whereas the addition of nanosized calcium carbonate coated with fatty acids delays crystallization of iPP, the effect being mainly ascribed to the physical state of the coating in the investigated temperature range for crystallization of iPP, as well as to possible dissolution by fatty acids of heterogeneities originally present in the polypropylene matrix.     

TOF-GISANS investigation of polymer infiltration in mesoporous TiO2 films for photovoltaic applications

The structure of porous TiO₂ films and TiO₂:poly(N-vinylcarbazole) (PVK) composite films is investigated with time-of-flight grazing incidence small-angle neutron scattering (TOF-GISANS). The TiO₂ films have been prepared by application of a sol–gel process with a diblock copolymer as structure directing agent, and the conductive polymer PVK is infiltrated in the porous network by spin coating and solution casting. The films show a hierarchical pore structure with mesopores 52 nm in size and additional large macropores with a diameter of about 180 nm. By matching the scattering contrast of the TiO₂ with the polymer information about the penetration of the polymer in the pores is determined. Whereas in the PVK film prepared by solution casting the pores are filled to a high degree; in the spin coated film, PVK wets only the TiO₂ pore walls and forms a solid overlying layer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1628–1635, 2010     

Phosphorus‐containing polyamide Mg(OH)2 nanocomposite coating on surface of poly(vinyl chloride) thin film: Study on thermal stability,flammability, and mechanical properties

Surface of poly(vinyl chloride) (PVC) thin films was coated using DOPO‐based polyamide (DBPA) coating and DBPA/Mg(OH)₂ nanocomposites (DBPN) coating by dip‐coating process. For this purpose, a new DOPO‐based dicarboxylic acid (DBDA) was synthesized and used for preparation of DBPA and organically surface modification of Mg(OH)₂ nanoparticles. The effects of DBPA and DBPN coatings on the morphology, thermal stability, combustion, and mechanical properties of PVC were investigated. The uniform dispersion of Mg(OH)₂ nanoparticles (nano‐MDH) and organically coating manner on the surface of the PVC films were confirmed by ATR‐IR spectroscopy, X‐ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), energy dispersive X‐ray, and elemental mapping. From thermal gravimetry analysis (TGA) results, the 10 mass% loss temperature (T₁₀) increased from 268°C to 272°C in PVC coated with DBPA‐containing 10 mass% of modified Mg(OH)₂ (MMH). Also the char residue, first and second mass loss temperatures of all PVC coated were increased compared with the neat PVC film. According to microscale combustion calorimetry (MCC) results, the peak of heat release rate (pHHR) and total heat release (THR) were decreased from 128 ± 2 to 69 W/g and 12 ± 1 to 4 ± 2 KJ/g for PVC film coated with DBPA‐containing 10 mass% of MMH, compared with the neat PVC. From tensile test results, tensile strength was increased from 31.78 ± 0.8 to 39.64 ± 0.9 MPa for PVC coated with polyamide‐containing 5 mass% of MMH compared with the neat PVC.     

Synthesis and mechanochemical properties of biobased ABCBA-type pentablock copolymers comprising poly-d-lactide (A), poly-l-lactide (B) and poly(1,2-propylene succinate) (C)

The ABCBA pentablock copolymers (p-d -l -PPS) comprising poly(d -lactide) (PDLA: A), poly(l -lactide) (PLLA: B) and poly(propylene succinate) (PPS: C) were successfully synthesized by two-step ring-opening polymerization (ROP) of d - and l -lactide using a dihydroxy-terminated PPS as a macro-initiator. The pentablock copolymers revealed the high stereocomplex (sc) crystallinity, thermal stability and elastomeric property in their solution-cast films. It was found that the T_g was found to be proportional to the PPS content, whereas the T_m was proportional to their average block length. The thermal resistivity of the copolymer films was found to be as high as 202°C owing to their sc formation. The copolymers also showed improved stereocomplexibility compared to the enantiomeric mixtures of triblock copolymers (PLLA-PPS-PLLA and PDLA-PPS-PDLA) having similar PLLA and PDLA chain lengths. These pentablock copolymers can afford thermoplastic elastomers or flexible plastic materials having a 100% bio-based content, showing high heat-resistive property.     

Thermomechanical investigation of a thick film of aniline-formaldehyde copolymer and poly(methyl methacrylate)

A thick film of aniline-formaldehyde copolymer and PMMA is synthesized via dispersion of aniline-formaldehyde copolymer powder as filler particles in PMMA with two different concentrations. Variation of the complex elastic modulus and mechanical loss factor (tanδ) with temperature is studied. It is observed that the complex elastic modulus decreases with temperature owing to thermal expansion of films. On the other hand, tanδ increases up to a characteristic temperature beyond which it shows a decreasing trend toward melting. Transition temperature T _g of sample S₁ (pure PMMA) is found to be 80°C. In sample S₂ (1 wt % aniline formaldehyde copolymer), the peak of tanδ at a lower temperature (66°C) corresponds to glass transition temperature T _g of the PMMA matrix, while the peak of tanδ at a higher temperature (107.8°C) corresponds to T _g of a polymer chain restricted by filler particles of aniline-formaldehyde copolymer. A further increase (10 wt % aniline-formaldehyde copolymer) in the concentration of filler particles of aniline-formaldehyde copolymer results in a more compact structure and a shift of T _g to a higher temperature, 122.2°C. This shift in the glass transition temperature of thick films of aniline-formaldehyde copolymer and PMMA is dependent upon the concentration of filler particles in the sample.     

Preparation and characterization of poly(styrene-alt-maleic acid)-b-polystyrene block copolymer self-assembled nanoparticles

Block copolymers poly(styrene-alt-maleic anhydride)-b-polystyrene (P(St-alt-MAn)-b-PSt) were synthesized via radical addition fragmentation chain transfer copolymerization. The maleic anhydride-containing segments of the block copolymer were hydrolyzed to form amphiphilic poly(styrene-alt-maleic acid)-b-polystyrene (P(St-alt-MA)-b-PSt). In aqueous solution, P(St-alt-MA)₇₃-b-PSt₈₁ and P(St-alt-MA)₅₈-b-PSt₁₃₀ formed stable dispersed spherical aggregates of approximately 25 and 40 nm, respectively. Particle size was stable under alkaline conditions and was little affected by the polymer concentration in the range of 0.025–1.0 mg mL^?1. The critical aggregation concentrations of the block copolymer self-aggregates were 1?×?10^?3 and 3?×?10^?3 mg mL^?1 for hydrophobic PSt block lengths of 130 and 81 monomer units, respectively. The nanoparticles had a negative surface charge at pH?>?2. Scanning electron microscopy images revealed that particle–particle coalescence did not occur upon drying of the film and the nanoparticles remained discrete. Controlled aspirin release from the nanoparticles was dependent on the structure of the block polymers and release medium.     

iPP Based Nanocomposites Filled with Calcium Carbonate Nanoparticles: Structure/Properties Relationships

Isotactic polypropylene (iPP) based nanocomposites filled with calcium carbonate nanoparticles (CaCO₃) were prepared by melt mixing and structure-properties relationships of the nanomaterials were studied. Elongated CaCO₃ nanopowders coated with two different coating agents, polypropylene-maleic anhydride graft copolymer (iPP-g-MA) and fatty acids (FA), were tested as nanoreinforced phases. The influence of surface treatment of the nanoparticles on the polymer/nanofillers interfacial adhesion and on the final materials properties was investigated. Morphological analysis showed that the selected coating agents induce different iPP/nanofiller adhesion degrees. Young's modulus increases as a function of the nanoparticles content and the coating agent nature. Finally, all the prepared nanocomposites showed a significant improvement of iPP barrier properties either to oxygen or to carbon dioxide.     

Poly(N,N‐dimethylacrylamide‐co‐4‐(ethyl)‐morpholine methacrylamide) copolymer as coating for CE

In this work, a new physically adsorbed coating for CE is presented. This coating is based on a poly(N,N‐dimethylacrylamide‐co‐4‐(ethyl)‐morpholine methacrylamide) (DMA/MAEM) copolymer synthesized in our laboratory. It is demonstrated that the direction and magnitude of the EOF in CE can be modulated by varying the composition of the DMA/MAEM copolymer and the type and pH of the BGE. Moreover, the DMA/MAEM coating provides %RSD_n = 5 values for migration times lower than 0.9% for the same capillary and day, whereas the %RSD_n = 25 obtained for the interday assay was lower than 2.9%. The stability of the coating procedure is also tested between capillaries obtaining %RSD_n = 15 values lower than 2.9%, demonstrating that this physically adsorbed copolymer gives rise to a stable and reproducible coating in CE. Finally, the usefulness of this new cationic copolymer as CE coating is demonstrated through different applications. Namely, it is demonstrated that the CE separation of basic proteins, nucleotides and organic acids is achieved in a fast and easy way by using the DMA/MAEM coated capillary. The use of fused bare silica capillaries did not allow the separation of these compounds under the same analytical conditions. These results demonstrate that this type of coating in CE provides the option of using BGEs that are useless when utilized together with bare silica capillaries making wider the application and possibilities of this analytical technique.     

Orthogonal solubility in fully conjugated donor-acceptor block copolymers: Compatibilizers for polymer/fullerene bulk-heterojunction solar cells

Donor-acceptor (D-A) type fully conjugated block copolymer systems have been rarely reported due to the challenges in synthetic approaches to prepare well-defined low-polydispersity products. In this work, fully conjugated block copolymers are synthesized in a one-pot reaction through Stille coupling polycondensation, by utilizing the end-functional polymer copolymerization method. End-functional P3HT are copolymerized with AA (2,7-dibromo-9-(heptadecan-9-yl)-9H-carbazole) and BB (4,7-bis(5-(trimethylstannyl)thiophen-2-yl)benzo[c][1,2,5]thiadiazole, TBT) type monomers, respectively. The orthogonal solubility between the very soluble P3HT donor and the insoluble PCDTBT acceptor block improves the purity of block copolymers as well as distinct nano-scale phase-separation compared with other reports on miscibility of donor and acceptor polymer block. Further purification via preparative GPC is carried out to remove the excess of unreacted P3HT and free PCDTBT as well as to achieve low polydispersity of block copolymers. The chemical structure of the P3HT-b-PCDTBT block copolymers are verified via ¹H-NMR, and further confirmed by FTIR spectra. The block copolymer shows broad absorption and moderate optical band gap of 1.8 eV. Furthermore, the fully conjugated block copolymer films exhibit significant fine structures, much smoother film morphology compared to P3HT/PCDTBT polymer blends. By adding a small amount of block copolymer P3HT-b-PCDTBT as a compatibilizer into the bulk-heterojunction of P3HT:PC₆₁BM blends, polymer solar cells with an 8% increase of short circuit current (J _sc and 10% increase of power conversion efficiency (PCE) are achieved owing to the improvement of the active-layer film morphology. To the best of our knowledge, this is the first report on donor-acceptor type fully conjugated block copolymer as an effective ternary additive in polymer: fullerene bulk heterojunction solar cells.     

Extension of the voltammetric theory to inert,permeable thin-film coated rotating disc electrodes: Part II. Behaviour of ferrocene-ferricinium ion and quinone-hydroquinone systems on polymer-coated electrodes

The voltammetric behaviour of ferrocene-ferricinium ion and quinone-hydroquinone systems is investigated on electrochemically thin film polymer coated electrodes. Ferrocene oxidation is studied in 0.1 M NBu₄ ClO₄-nitromethane on rotating disc platinum electrodes coated with poly(2-hydroxymethyl-1,4-phenylene) oxide (I), poly-(2,6-dimethyl-1,4-phenylene) oxide (II), and poly[4-(2-aminoethyl)-1,2-phenylene] oxide (III) films. The quinone-hydroquinone system is investigated in aqueous medium (1 M HClO₄) with (I), (II) and poly-(2-cyano-1,4-phenylene) oxide films. Experimental results are in good agreement with the previously calculated voltammetric curves in steady-state mass transfer conditions. The charge transfer and diffusion parameters on these polymer-coated electrodes are calculated The quinone-hydroquinone system is rendered reversible by coating a platinum electrode with I.