Influence of Synthesis Conditions on the Morphology and Spectral-Luminescent Properties of Films of Organic-Inorganic Perovskite CH<Subscript>3</Subscript>NH<Subscript>3</Subscript>PbI<Subscript>2.98</Subscript>Cl<Subscript>0.02</Subscript>

The influence of the synthesis conditions (rotation speed used for spin-coating deposition of the film, film drying temperature, and the ratio of the PbI₂ and CH₃NH₃I reactants in solutions) on the microstructure, phase composition, and spectral-luminescent properties of films of organic-inorganic perovskite CH₃NH₃PbI_3–xCl _x (x = 0, 0.02) was elucidated.     

In situ thermo-optical studies of polymer:fullerene blend films

Optical properties of a blend thin film (1:1 wt) of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) exposed to a stepwise heating and cooling, have been reported and compared with the properties of pure PCBM and P3HT films. The UV–Vis(T) absorption measurements were performed in situ, during annealing and cooling runs, at the precisely defined temperatures, in a range of 20–210 °C. It was demonstrated that this new method allows to observe the changes of absorption coefficient spectra and absorption edge parameters: the energy gap (E_G) and the Urbach energy (E_U), connected with the length of conjugation and structural disorder of thin film, respectively. Several stages, during annealing/cooling runs, were distinguished for the P3HT:PCBM blend film and related to the following processes, as an increase of P3HT crystallinity in the blend, the orderly stacking of polymer chains, thermally induced structural defects and the phase separation, caused by an aggregation of PCBM in the polymer matrix. These changes were also observed on the P3HT:PCBM film surface, by means to the microscopic studies.     

The preparation and properties of bulk-heterojunction organic solar cells with indole-containing fulleropyrrolidine derivatives as acceptors

Two indole-containing fullerene derivatives, N-hydrogen-2-[3-(N-2-ethylhexylindolyl)][60]fulleropyrrolidine (EHIHC60P), and N-(2-ethylhexylindolyl))-2-[3-(N-2-ethylhexylindolyl)][60]fulleropyrrolidine (DEHIC60P) were synthesized by the typical Prato reaction. The absorption spectra, electrochemical properties of the two compounds were measured. Inverted solar cells were fabricated with the structure of ITO/ZnO/poly(3-hexylthiophene) (P3HT):fullerene derivatives/MoO₃/Ag. The highest power conversion efficiencies (PCEs) of 3.32% and 3.23% were obtained for P3HT/EHIHC60P and P3HT/DEHIC60P based solar cells at the composite ratio of 1:1 after the active layers were annealed at 150 °C under inert atmosphere, with a open-circuit voltage (V_oc) of 0.66 V and 0.74 V, respectively. For comparison, the device based on P3HT/PCBM at the same conditions showed the PCE of 3.28%, with a V_oc of 0.61 V. The influence on the photovoltaic property of the fullerene derivatives, which was induced by some subtle changes in the chemical structure was compared and discussed.     

Isomerism in tetrahedral rhenium cluster complexes [Re4Q4(PMe2Ph)4X8]·nCH2Cl2 (Q = Se, X = Br; Q = Te, X = Cl, Br)

Three new tetrahedral rhenium cluster compounds [Re₄Se₄(PMe₂Ph)₄Br₈]·1.5CH₂Cl₂ (1), [Re₄Te₄(PMe₂Ph)₄Br₈]·CH₂Cl₂ (2), and [Re₄Te₄(PMe₂Ph)₄Cl₈]·CH₂Cl₂ (3) have been synthesized by the reaction of the corresponding precursor chalcohalide complexes [Re₄Q₄(TeX₂)₄X₈] (X = Br, Q = Se (for 1), Te (for 2); X = Cl, Q = Te (for 3)) with dimethylphenylphosphine in CH₂Cl₂. All compounds have been characterized by X-ray single-crystal diffraction and elemental analyses, IR and ³¹P NMR spectroscopy. ³¹P NMR spectroscopy indicates the formation of isomers in solution, confirmed by single-crystal X-ray analysis.     

An efficient and simple Morita-Baylis-Hillman reaction based on the N-methylpyrrolidine-Ba(OH)2 catalytic system

By using of precise catalytic amount of N-methylpyrrolidine (5 mol %) and Ba(OH)₂ (1.5 mol %) in H₂O/CH₃OH 5/1 or CH₃OH/CH₂Cl₂ 3/1 solvent mixtures at T=0 °C a Morita-Baylis-Hillman derivatives could be obtained in good to excellent yield from 2-cyclopenten-1-one, 2-cyclohexen-1-one and formaldehyde and diverse aryl aldehydes after suitable reaction time.     

O-Alkyldithiophosphate Nickel Complexes with dcpf Ligand as Efficient Electrocatalysts for Hydrogen Evolution

Six new O-alkyldithiophosphate nickel complexes with dcpf ligand, [(dcpf)Ni(S₂P{O}OR)] (dcpf = 1,1′-bis (dicyclohexylphosphino)ferrocene, R = CH₃ ( 1 ), CH₃CH₂ ( 2 ), Ph ( 3 ), 4-MeC₆H₄ ( 4 ), PhCH₂ ( 5 ) and PhCH₂CH₂ ( 6 )), have been synthesized by the treatment of dcpf with ((RO)₂PS₂)₂Ni in satisfactory yields. These complexes were characterized by elemental analysis, spectroscopy (FTIR, UV–vis, ¹H, ¹³C, and ³¹P NMR), thermogravimetric analysis and single crystal X-ray diffraction. The nickel atom in 1 , 2 ·CH₂Cl₂, 3 ·CH₂Cl₂, 4 ·2CH₂Cl₂·THF, and 2( 5 )·hexane adopts a slightly distorted square-planar coordination environment finished by two phosphorus atoms of dcpf ligand and two sulfur atoms of O-alkyldithiophosphate ligand. Furthermore, the electrochemical properties for complexes 1 – 6 were also investigated by cyclic voltammetry. With the addition of 120 mM trifluoroacetic acid (TFA), the turnover frequency (TOF) values for 1 – 6 are estimated to be 1243.83, 1046.54, 1331.71, 2545.29, 1899.03, and 1191.37 s⁻¹, with the overpotential (η) values of 0.62, 0.58, 0.71, 0.67, 0.60, and 0.56 V, respectively. The result of electrochemical studies indicates that all complexes can be used as efficient molecular eletrocatalysts for the reduction of protons to hydrogen in the presence of TFA in MeCN.     

Mechanistic investigation, kinetic modeling and analysis parameters of poly(3-hexylthiophene) degradation to fullerenes

Thermal degradation of Poly (3-hexylthiopene) (P3HT) was studied under nitrogen environment. Kinetic parameters of thermal degradation were determined using Vyazovkin model free method and model fitting method. Vyazovkin model free kinetic analysis is carried out to understand the variation of activation energy (E_α) required for degradation of polymer with conversion (α). Various reaction models have been tested for probable reaction mechanism using hybrid genetic algorithm (HGA). Diffusion model and nucleation & growth with n = 2/3 has prominent role in thermal decomposition of P3HT. A plausible degradation route is proposed based on the experimental details acquired from gas chromatography (GC), Raman spectroscopy, FTIR spectroscopy, powder X-ray diffractometry (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Degradation of P3HT starts at around 195 °C with release of lighter units like CS. Further increase in the temperature results in detachment of the hexyl chain from P3HT and the residue obtained at 1050 °C contains fullerenes mixed with amorphous carbon.     

The first example of hydrozirconation of alkynes in room temperature ionic liquids

Hydrozirconation of terminal alkynes in 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]) at 30 °C gave highly regio- and stereoselectively (E)-vinylzirconium complexes, which underwent a cross-coupling reaction with aryl halides in the presence of Pd(PPh₃)₄ to afford (E)-1,2-disubstituted ethenes in good to high yields. Our system not only avoids the use of easily volatile THF or CH₂Cl₂ as solvent but also solves the basic problem of palladium catalyst reuse.     

Enantiomer separation of rac-2,2′-dihydroxy-1,1′-binaphthyl (BNO) by inclusion complexation with racemic or achiral ammonium salts and a novel transformation of a 1:1:1 racemic complex of BNO, Me4N·Cl and MeOH into a conglomerate complex in the solid state

The complete simultaneous and mutual enantiomer resolution of 2,2′-dihydroxy-1,1′-binaphthyl (BNO) and N-(3-chloro-2-hydroxypropyl)-N,N,N-trimethylammonium chloride, Me₃N⁺CH₂CH(OH)CH₂Cl·Cl⁻ into their enantiomers by inclusion complexation between their racemates in EtOH in the presence of a chiral seed crystal is reported. The enantiomer resolution of the rac-BNO was also accomplished easily by inclusion complexation with achiral ammonium salts, N-(2-hydroxyethyl)-N,N,N-trimethylammonium chloride, Me₃N⁺CH₂CH₂OH·Cl⁻ and tetramethylammonium chloride, Me₄N⁺·Cl⁻. Inclusion complexation of the rac-BNO with Me₃N⁺ CH₂CH₂OH·Cl⁻ gave only a 1:1 conglomerate inclusion complex but not a racemic complex. Recrystallization of the rac-BNO and an equimolar amount of Me₄N⁺·Cl⁻ from MeOH (7 ml) and MeOH (15 ml) gave a 1:1:1 racemic complex, BNO·Me₄N⁺·Cl⁻·MeOH and a 1:1 conglomerate complex, BNO·Me₄N⁺·Cl⁻, respectively. Novel transformation of the former racemate into the latter conglomerate occurred by heating or by exposure to MeOH vapor in the solid state.     

Cationic iridium complexes of the Xantphos ligand. Flexible coordination modes and the isolation of the hydride insertion product with an alkene

Reaction of the Ir(I)-Xantphos complex [Ir(κ²-Xantphos)(COD)][BAr^F₄] (Xantphos = 4,5-bis(diphenylphosphino)-9,9-dimethylxanthene, Ar^F = C₆H₃(CF₃)₂) with H₂ in acetone or CH₂Cl₂/MeCN affords the Ir(III)-hydrido complexes [Ir(κ³-Xantphos)(H)₂(L)][BAr^F₄], L = acetone or MeCN, whereas in non-coordinating CH₂Cl₂ solvent dimeric [Ir(κ³-Xantphos)(H)(μ-H)]₂[BAr^F₄]₂ is formed. A common intermediate in these reactions that invokes a (σ, η²-C₈H₁₃) ligand is reported. Addition of excess tert-butylethene (tbe) to [Ir(κ³-Xantphos)(H)₂(MeCN)][BAr^F₄] results in insertion of a hydride into the alkene to form [Ir(κ³-Xantphos)(MeCN)(CH₂CH₂C(CH₃)₃)(H)][BAr^F₄], an Ir(III) alkyl-hydrido-Xantphos complex. This reaction is reversible, and heating (80 °C) results in the reformation of [Ir(κ³-Xantphos)(H)₂(MeCN)][BAr^F₄] and tbe. These complexes have been characterised by NMR spectroscopy, ESI-MS and single-crystal X-ray diffraction. They show variable coordination modes of the Xantphos ligand: cis-κ²-P,P, fac-κ³-P,O,P and mer-κ³-P,O,P with the later coordination mode like that found in related PNP-pincer complexes.     

Si-C coupling reaction of polychloromethanes with HSiCl3 in the presence of Bu4PCl: Convenient synthetic method for bis(chlorosilyl)methanes

Coupling reaction of polychloromethanes CH_4−nCl_n (n = 2-4) with HSiCl₃ in the presence of tetrabutylphosphonium chloride (Bu₄PCl) as a catalyst occurred at temperatures ranging from 30 °C to 150 °C. The reactivity of polychloromethanes increases as the number of chlorine-substituents on the carbon increases. In the reactions of CCl₄ with HSiCl₃, a variety of coupling products such as bis(chlorosilyl)methanes CH₂(SiCl₃)(SiXCl₂) [X = Cl (1a), H (1b)], (chlorosilyl)trichloromthanes Cl₃CSiXCl₂ [X = Cl (2a), H (2b)], and (chlorosilyl)dichloromthanes Cl₂HCSiXCl₂ [X = Cl (3a), H (3b)] were obtained along with reductive dechlorination products such as CHCl₃ and CH₂Cl₂ depending on the reaction temperature. In the reaction of CCl₄, 2a is formed at the initial stage of the coupling reaction and converted to give CHCl₃ at low temperature of 30 °C, to give 1a, 3a, and CHCl₃ at 60 °C, and to afford 1a as major product and CH₂Cl₂ in competition above 100 °C. Si-H bond containing silylmethanes can be formed by the H-Cl exchange reaction with HSiCl₃. Reaction of CHCl₃ with HSiCl₃ took placed at 80 °C to give three compounds 1a, 3a, and CH₂Cl₂, and finally 3a was converted to give 1a and CH₂Cl₂ at longer reaction time. While the condition for the reaction of CH₂Cl₂ with HSiCl₃ required a much higher temperature of 150 °C. Under the optimized conditions for synthesizing bis(chlorosilyl)methanes 1a,b, a mixture of 1a and 1b were obtained as major products in 65% (1a:1b = 64:1) and 47% (42:5) yields from the reaction of CCl₄ and CHCl₃ at 100 °C for 8 h, respectively, and in 41% (34:7) yield from that of CH₂Cl₂ at 170 °C for 12 h. In the Si-C coupling reaction of polychloromethanes with HSiCl₃, it seems likely that a trichlorosilyl anion generated from the reaction of HSiCl₃ with Bu₄PCl is an important key intermediate.     

Controlling the surface composition of PCBM in P3HT/PCBM blend films by using mixed solvents with different evaporation rates

The surface composition of poly(3-hexylthiophene-2,5-diyl) and fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (P3HT/PCBM) blend films could be changed by controlling the film formation process via using mixed solvents with different evaporation rates. The second solvent, with a higher boiling point than that of the first solvent and much better solubility for PCBM than P3HT, is chosen to mix with the first solvent with a lower boiling point and good solubility for both PCBM and P3HT. The slow evaporation rate of the second solvent provides enough time for PCBM to diffuse upwards during the solvent evaporation. Thus, the weight ratio of PCBM and P3HT (m _PCBM/m _P3HT) at surface of the blend films was varied from ca. 0.1 to ca. 0.72, i.e., it increases about seven times by changing from single solvent to mixed solvents. Meanwhile, the mixed solvents were in favor to form P3HT naonofiber network and enhance phase separation of P3HT/PCBM blend films. As a result, the power conversion efficiency of the device from mixed solvents with slow evaporation process was about 1.5 times of the one from single solvents.     

Quantum chemical study on insertion and abstraction reaction of dichlorocarbene with methyl alcohol and methyl mercaptan

The insertion and abstraction reaction mechanisms of singlet and triplet CCl₂ with CH₃MH (M=O, S) have been studied by using the DFT, NBO and AIM methods. The geometries of reactions, the transition state and products were completely optimized by B3LYP/6–311G(d, p). All the energy of the species was obtained at the CCSD(T)/6–311G(d, p) level. The calculated results indicated that the major pathways of the reaction were obtained on the singlet potential energy surface. The singlet CCl₂ can not only trigger the insertion reaction with C-H and M-H in four pathways, by which the products P1 [CH₃OCHCl₂, reaction I(1)], P3[Cl₂HCCH₂OH, reaction I(2)], P5[CH₃SCHCl₂, reaction II(1)] and P7[Cl₂HCCH₂SH, reaction II(2)] are produced respectively, but also abstract M-H, resulting P4 [CH₂O+CH₂Cl₂, reaction I(3)] and P8[CH₂S+CH₂Cl₂, reaction II(3)]. In addition, the important geometries in domain pathways have been studied by AIM and NBO theories. Supported by the National Natural Science Foundation of China (Grant No. 20335030) and Foundation of Education Committee of Gansu Province (Grant No. 0708-11)     

The Er and Yb Complexes with Silicon-Containing Phosphates and Fluorine-Containing Phosphine Oxide: Synthesis,Spectra, and Films

Three new silicon- and fluorine-containing ligands, namely bis(dimethylamido)(3-triethoxysilylpropylamido)phosphate O=P(NMe₂)₂NHCH₂CH₂CH₂Si(OEt)₃, diphenyl(3-triethoxysilylpropylamido)phosphate O=P(OPh)₂NHCH₂CH₂CH₂Si(OEt)₃, and tris(3,3,3-trifluoropropyl)phosphine oxide O=P(CH₂CH₂CF₃)₃ are synthesized. The erbium and ytterbium complexes with amine, phosphate, and phosphine oxide ligands Ln(NH₂R)₃Cl₃, Ln[O=P(NMe₂)₂NHR]₃Cl₃, Ln[O=P(OPh)₂NHR]₃Cl₃ (R=CH₂CH₂CH₂Si(OEt)₃), Ln[O=P(OPh)₃]₃Cl₃, Ln[O=P(CH₂CH₂CF₃)₃]₃Cl₃ are produced and their electronic absorption spectra and photoluminescence spectra are studied. The silicon-containing compounds form transparent thermostable films on silicate glass or quartz surface.     

Synthesis,characterization and reactions of the transition metal halogenoalkyl carbocation complexes [Cp(CO)2M{η2-CH2CH(CH2)nX}]PF6 (n = 1–8, 10, M = Fe; n = 3, 4 M = Ru; X = Br,I)

The halogenoalkyl complexes [Cp(CO)₂M{(CH₂)_nX}] (n = 3–10, 12, M = Fe; n = 5, 6, M = Ru, X = Br, I) react with Ph₃CPF₆ in dry CH₂Cl₂ to give the corresponding carbocation complexes [Cp(CO)₂M{η²-(CH₂CH(CH₂)_n?2X}]PF₆ in high yields. NMR evidence indicates that the metals form metallacyclopropane type structures with the carbocation ligand. The reactions of some of the cationic complexes with NaI, PPh₃, Na[Cp(CO)₂Fe] and Et₃N are discussed. NaI and Na[Cp(CO)₂Fe] displace the halogeno-olefin, while PPh₃ adds at the β-CH^δ+ giving the unstable phosphonium adducts [Cp(CO)₂Fe{CH₂CH(PPh₃)(CH₂)_n?2X}]PF₆ which decompose to the halogeno-olefins and the cationic PPh₃ complex [Cp(CO)₂Fe(PPh₃)]⁺. Et₃N causes allylic deprotonation forming internal olefin complexes of the type [Cp(CO)₂Fe{CH₂CHCH(CH₂)_n?3X}]PF₆.     

Modifying transparent electrode with conjugated organic semiconductor hole transport material as interface for enhancing performance of organic solar cell

Indium tin oxide (ITO) is used as a substrate was covered with 4-[4-(4-methoxy-N-naphthalen-2-ylanilino) phenyl] benzoic acid (MNA) as a self-assembled monolayer (SAM). Poly(3-hexylthiophene) (P3HT) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6) C₆₁ (PCBM) were mixed and used as a donor–acceptor in organic solar cell (OSC). The MNA (SAM) layer is used as an interface instead of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT: PSS) for hole injection. The HOMO-LUMO energy level of MNA-SAM molecule and the electronic charge distribution were calculated theoretically using Chemissian software. The HOMO-LUMO energy level of the MNA is calculated as E_HOMO = ?5.10 eV and E_LUMO = ?1.60 eV. The OSC modified with MNA showed an efficient performance in the absence of PEDOT: PSS as hole transport layer. The annealing of the ITO/SAM/P3HT: PCBM films at different temperatures are also investigated to study the effect of reducing defects. The interface structures of the organic semiconductor layer on ITO were characterized by Atomic Force Microcopy (AFM). In addition, Kelvin Probe Microscopy (KPM) is used to understand how the annealing changes the surface potential energy of the ITO/SAM substrate. Using the KPM method, which measures the surface potential energy of the films, the energy bands of the ITO were increased to maximum 5.09 eV. The ITO/SAM/P3HT: PCBM film's surface potential was determined to be 0.18 eV after being annealed at 80 °C. The surface potential of the modified films was discovered to be 0.33 V and 0.39 V when the annealing temperature was raised from 80 °C to 120 °C and 160 °C. The maximum device efficiency was demonstrated by the ITO/SAM/P3HT: PCBM film after an hour of annealing at 160 °C.     

Tellurium(II) and tellurium(IV) complexes of phosphine chalcogenide ligands,synthesis and X-ray structures

Reaction of TeX₄ (X = Cl or Br) with 2 mol. equiv. of OPR₃ (R = Me, Et or Ph) gives the distorted octahedral cis-[TeX₄(OPR₃)₂], while the bidentates Ph₂P(E)(CH₂)_nP(E)Ph₂ (E = O, n = 1 or 2; E = S, n = 1) give the six-coordinate [TeX₄{Ph₂P(E)(CH₂)_nP(E)Ph₂}]. These species have been characterised spectroscopically (via ¹H and ³¹P{¹H} NMR and IR) and by crystallographic analyses on cis-[TeBr₄(OPPh₃)₂], [TeCl₄{Ph₂P(O)CH₂P(O)Ph₂}] and [TeBr₄{Ph₂P(S)CH₂P(S)Ph₂}]. The TeX₄ (X = Cl or Br) are reduced by Ph₂P(S)(CH₂)₂P(S)Ph₂ and Ph₂P(Se)CH₂P(Se)Ph₂, giving the planar, four-coordinate Te(II) species [Te{Ph₂P(S)(CH₂)₂P(S)Ph₂}₂]²⁺ (isolated as [(TeCl₅)₂{μ-Ph₂P(S)(CH₂)₂P(S)Ph₂}]^2? and [TeBr₆]^2? salts) and [TeBr₂{Ph₂P(Se)CH₂P(Se)Ph₂}], all of which have also been identified crystallographically. On the basis of the structural data the Te-based lone pair associated with the Te(IV) species is assumed to occupy the 5s orbital, whereas in the Te(II) complexes the planar coordination is consistent with the two stereochemically active lone pairs occupying the axial sites.     

Diorganotin(IV) complexes of N-mono-, di- and tri-chloroacetyl,N′,N″-bis(isopropyl) phosphoric triamide

Three new carbacylamidophosphates with formula CH_nCl_3?nC(O)NHP(O)(NHCH(CH₃)₂)₂ (n = 2 (1); n = 1 (2); n = 0 (3)) and their organotin compounds with formula (1)SnCl₂Me₂(μ-1)SnCl₂Me₂ (4), SnCl₂Me₂(2)₂·C₆H₅CH₃ (5) and [SnCl₂Me₂(3)]_n (6) were synthesized and characterized by elemental, IR and NMR spectra analyses. The spectroscopic properties of complexes were compared with those corresponding ligands. The crystal structures of complexes were determined by X-ray crystallography, which reveals that complex 4 is binuclear structure with two non-equivalent Sn atoms. One adopts a distorted trans(C,C) cis(O_P,O_P) cis(Cl,Cl) octahedral configuration, while the other adopts a distorted trigonal bipyramidal geometry composed of two methyl groups, two chlorine atoms and carbonyl group. Molecule 5 is centrosymmetric with two O_P, disordered chlorine and methyl groups in trans positions. Toluene molecules are located in the interlayer spaces of 5. In compound 6, bonding via both PO and CO functionalities forms 1D infinite chain structures along b axis. The Sn–O_P bond length in 6 is significantly longer than the same distance in 4 and 5, while the OP and Sn–Cl bonds are shorter. The bond lengths in these complexes were compared with those of N-benzoyl carbacylamidophosphates.     

The unusual inhibition of a dirhodium tetraphosphine-based bimetallic hydroformylation catalyst by PPh3

The addition of even small amounts of PPh₃ to the dirhodium tetraphosphine hydroformylation catalyst generated from 〚rac-Rh₂(nbd)₂(et,ph-P4)〛(BF₄)₂ (nbd = norbornadiene; et,ph-P4 = Et₂CH₂CH₂(Ph)PCH₂P(Ph)CH₂CH₂PEt₂) causes a dramatic drop in the aldehyde linear-to-branched regioselectivity (25:1 to 3:1) in acetone solvent (90 °C, 6.1 bar, 1-hexene). Catalytic results are presented for differing amounts of added PPh₃ along with comparisons to the monometallic Rh catalyst family, HRh(CO)_x(PPh₃)_y (x = 1–3; y = 3 – x), generated from PPh₃ and Rh(acac)(CO)₂ (acac = acetylacetonate). The results point to the extremely effective inhibition of the regioselective bimetallic hydroformylation mechanism and the formation of an inefficient monometallic catalyst cycle, but not fragmentation to generate free HRh(CO)(PPh₃)₂ catalysts.