Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Novel poly(N‐isopropylacrylamide)/clay/poly(acrylamide) IPN hydrogels with the response rate and drug release controlled by clay content

Novel interpenetrating network (IPN) hydrogels (PNIPAAm/clay/PAAm hydrogels) based on poly(N‐isopropylacrylamide) (PNIPAAm) crosslinked by inorganic clay and poly(acrylamide) (PAAm) crosslinked by organic crosslinker were prepared in situ by ultraviolet (UV) irradiation polymerization. The effects of clay content on temperature dependence of equilibrium swelling ratio, deswelling behavior, thermal behavior, and the interior morphology of resultant IPN hydrogels were investigated with the help of Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), scanning electron microscope (SEM). Study on temperature dependence of equilibrium swelling ratio showed that all IPN hydrogels exhibited temperature‐sensitivity. DSC further revealed that the temperature‐sensitivity was weakened with increasing amount of clay. Study on deswelling behavior revealed that IPN hydrogels had much faster response rate when comparing with PNIPAAm/clay hydrogels, and the response rate of IPN hydrogels could be controlled by clay content. SEM revealed that there existed difference in the interior morphology of IPN hydrogels between 20 [below lower critical solution temperature (LCST)] and 50 °C (above LCST), and this difference would become obvious with a decrease in clay content. For the standpoint of applications, oscillating swelling/deswelling behavior was investigated to determine whether properties of IPN hydrogels would be stable for potential applications. Bovine serum albumin (BSA) was used as model drug for in vitro experiment, the release data suggested that the controlled drug release could be achieved by modulating clay content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 96–106, 2009     

Stimulus response and molecular structural modification of polyacrylamide gel in nitric acid: A study by Raman,FTIR, and photoluminescence techniques

Stimulus response of photopolymerized 1% and 0.5% N,N′‐methylene bisacrylamide (MBA) crosslinked 10% polyacrylamide (PAAm) hydrogels was studied in nitric acid. The hydrogels swelled exponentially to saturation in 13 h due to the osmotic pressure arising from diffusion of ions in to the gel. MBA (0.5%) gels swell more with larger time constant than 1% MBA gels due to lower bulk modulus. Diffusion coefficient of nitric acid in the hydrogel and polymer‐solvent interaction parameter were estimated from the swelling behavior and discussed. At longer times, the hydrogels deswelled linearly in nitric acid due to molecular modification of amide group by acidic hydrolysis. Degree of swelling and deswelling increase with nitric acid concentration. Raman and FTIR investigations revealed the formation of carboxylic acid due to acidic hydrolysis. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 710–720, 2008     

Swelling of polyacrylamide gels in polyacrylamide solutions

Swelling behavior of polyacrylamide (PAAm) and polyacrylamide-co-polyacrylic acid (PAAm-co-PAAc) gels was investigated in aqueous solutions of monodisperse PAAms with molecular weights (M_w) ranging from 1.5 × 10³ to 5 × 10⁶ g/mol. The volume of the gels decreases as the PAAm concentration in the external solution increases. This decrease becomes more pronounced as the molecular weight of PAAm increases. The classical Flory–Huggins (FH) theory correctly predicts the swelling behavior of nonionic PAAm gels in PAAm solutions. The polymer–polymer interaction parameter χ₂₃ was found to decrease as the molecular weight of PAAm increases. The swelling behavior of PAAm-co-PAAc gels in PAAm solutions deviates from the predictions of the FH theory. This is probably due to the change of the ionization degree of AAc units depending on the polymer concentration in the external solution. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1313–1320, 1998     

Birefringent hydrogels based on PAAm and lyotropic liquid crystal: Optical, morphological and hydrophilic characterization

In this work, hydrogels of polyacrylamide (or PAAm) with confined lyotropic liquid crystal (potassium laurate-decanol-water, KL-DeOH-H₂O) (or LLC) were synthesized. The hydrogels were characterized by polarized optical microscopy (POM), refractometry, optical transmission, scanning electron microscopy (SEM) and small angle X-ray scattering (SAXS). Besides these techniques, the hydrophilicity of hydrogels was characterized by the degree of swelling. Based on POM, it was observed that the texture of the birefringent hydrogels obtained depends on their cross-linking density, and that it is formed soon after hydrogel synthesis. Refractometry results indicated an behavior antagonist to that obtained for the system constituted by thermotropic liquid crystal inserted into the PAAm lattice in relation to the dependence of Δn on the AAm concentration and the optical transmittance. SEM micrographs show that birefringent hydrogels present rougher surface when compared to the surface of PAAm hydrogels. For the same AAm concentrations, it was observed that the hydrogels with confined LLC present larger swelling values (Q) when compared to those of PAAm hydrogels. The loss of water by birefringent hydrogels is twofold slower than that of PAAm hydrogels. Hydrogels formed by PAAm and lyotropic liquid crystal synthesized in this work can be potentially used in optical devices.     

Synthesis and characterization of poly(N‐vinyl formamide) hydrogels—A potential alternative to polyacrylamide hydrogels

The synthesis and characterization of solution‐cast, molded gels of N‐vinyl formamide (NVF) has not been previously reported even though NVF is an isomer of acrylamide (AAm) and polyacrylamide (PAAm) hydrogels have many commercial applications. Aqueous NVF solutions were cross‐linked into gels using a novel cross‐linker, 2‐(N‐vinylformamido)ethylether, and the thermally‐activated initiator VA‐044. For a given formulation, PNVF gels swell up to twice that of PAAm gels cross‐linked with N,N′‐methylenebisacrylamide. From swelling and compression measurements, PNVF gels were found to be more hydrophilic than PAAm gels. Flory‐Huggins solubility parameters were χ = 0.38?₂ + 0.48 for PNVF and χ = 0.31?₂ + 0.49 for PAAm, where ?₂ is the polymer volume fraction. The shear moduli for PNVF and PAAm scale with ? and ? respectively, consistent with good solvent behavior, also suggesting PNVF is more hydrophilic than PAAm. Similarity of mechanical properties for both gels as a function of ?₂ suggests that network structures of PNVF and PAAm gels are similar. Fracture strains of both gels declined with ?₂ by the same linear function while fracture stresses were about 500 kPa regardless of formulation. Since NVF is a liquid monomer, less toxic than AAm and can be hydrolyzed to a cationic form, PNVF gels could become technologically significant. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Interactions of glucose and polyacrylamide in solutions and gels

The swelling of polyacrylamide (PAAm) gels increased with rising glucose concentrations, and so did the osmotic pressure of the soluble polymer and its intrinsic viscosity. A Flory–Huggins‐based model for the osmotic pressure of a nonionic hydrophilic polymer in a ternary solution consisting of a main solvent, a polymer, and a nondissociating low‐molecular‐weight cosolute was developed and examined. The model‐calculated values were in reasonably good agreement with experimental results for the water–PAAm–glucose system studied when PAAm–water and glucose–water interaction coefficients from the binary systems were used, and only the PAAm–glucose interaction coefficient was adjusted. Its negative value suggested a favorable interaction of glucose and PAAm, supporting the notion of glucose being a good cosolvent for PAAm. Isothermal titration microcalorimetry results showed no evidence for the binding of glucose to PAAm, but an exothermic interaction was indicated between glucose and PAAm. Microcalorimetrically determined enthalpic contributions to the Flory–Huggins interaction coefficients showed enthalpically favorable binary interactions, particularly the enthalpic component of the PAAm–glucose interaction coefficient (χ_H23), which was slightly negative. The enthalpically favorable interaction between glucose and PAAm may explain the increased osmotic pressure of PAAm in glucose solutions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3053–3063, 2003     

Hierarchically structured free-standing hydrogels with liquid crystalline domains and magnetic nanoparticles as dual physical cross-linkers

Here we report a modular strategy for preparing physically cross-linked and mechanically robust free-standing hydrogels comprising unique thermotropic liquid crystalline (LC) domains and magnetic nanoparticles both of which serve as the physical cross-linkers resulting in hydrogels that can be used as magnetically responsive soft actuators. A series of amphiphilic LC pentablock copolymers of poly(acrylic acid) (PAA), poly(5-cholesteryloxypentyl methacrylate) (PC5MA), and poly(ethylene oxide) (PEO) blocks in the sequence of PAA-PC5MA-PEO-PC5MA-PAA were prepared using reversible addition-fragmentation chain transfer polymerization. These pentablock copolymers served as macromolecular ligands to template Fe(3)O(4) magnetic nanoparticles (MNPs), which were directly anchored to the polymer chains through the coordination bonds with the carboxyl groups of PAA blocks. The resulting polymer/MNP nanocomposites comprised a complicated hierarchical structure in which polymer-coated MNP clusters were dispersed in a microsegregated pentablock copolymer matrix that further contained LC ordering. Upon swelling, the hierarchical structure was disrupted and converted to a network structure, in which MNP clusters were anchored to the polymer chains and LC domains stayed intact to connect solvated PEO and PAA blocks, leading to a free-standing LC magnetic hydrogel (LC ferrogel). By varying the PAA weight fraction (f(AA)) in the pentablock copolymers, the swelling degrees (Q) of the resulting LC ferrogels were tailored. Rheological experiments showed that these physically cross-linked free-standing LC ferrogels exhibit good mechanical strength with storage moduli G' of around 10(4)-10(5) Pa, similar to that of natural tissues. Furthermore, application of a magnetic field induced bending actuation of the LC ferrogels. Therefore, these physically cross-linked and mechanically robust LC ferrogels can be used as soft actuators and artificial muscles. Moreover, this design strategy is a versatile platform for incorporation of different types of nanoparticles (metallic, inorganic, biological, etc.) into multifunctional amphiphilic block copolymers, resulting in unique free-standing hybrid hydrogels of good mechanical strength and integrity with tailored properties and end applications.     

Syntheses and characterization of physically crosslinked hydrogels from dithiocarbamate‐derived polyurethane macroiniferter

A dithiocarbamate (DC)‐based polyurethane macroiniferter (PUMI) was synthesized and used to prepare physically crosslinked polyurethane‐block‐poly (acrylamide) (PU‐b‐PAAm) and polyurethane‐block‐poly(vinyl pyrrolidone) (PU‐b‐PVP) hydrogels. The success of the reactions has been confirmed by FTIR, ¹H‐NMR, and ¹³C‐NMR Spectroscopy analyses. The number average molecular weight of the block copolymers increased linearly with conversion and copolymerization time and thus followed a “living” radical mechanism. The water transport behavior of these polyurethane‐based hydrogels such as water uptake rate, equilibrium water content (EWC), transport number (n), characteristic diffusion rate constant (K), diffusion coefficient (D), and pH effect on EWC has been investigated. The results revealed that PU‐b‐PAAm hydrogels followed Fickian diffusion suggesting diffusion controlled swelling kinetics, whereas the PU‐b‐PVP hydrogels followed non‐Fickian diffusion indicating that both diffusion and structural relaxation controlled the water transport. The PU‐b‐PAAm hydrogels showed higher swelling at both low and high pH than at a neutral pH. This is attributed to protonation of the tertiary amines of N,N′‐diethyl‐N,N′‐bis(2‐hydroxyethyl) thiuram disulfide (DHTD) at low pH and base hydrolysis of amide segments at high pH. In the thermogravimetric analysis; PUMI, PU‐b‐PVP and PU‐b‐PAAm have degraded in three distinct stages related to CS₂ evolution, hard segment degradation, and soft segment degradation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6272–6284, 2008     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Swelling Behavior of Semi‐Interpenetrating Polymer Network Hydrogels Based on Chitosan and Poly(acryl amide)

Semi‐interpenetrating polymer networks (semi‐IPNs) composed of chitosan and polyacrylamide (PAAm) hydrogels have been prepared, and the effect of changing pH, temperature, ionic concentration, and applied electric fields on the swelling of the hydrogels was investigated. The swelling kinetics increased rapidly, reaching equilibrium within 60 min. The semi‐IPN hydrogels exhibited a relatively high swelling ratios of 385%–569% at T=25°C. The swelling ratio increased with decreasing pH below pH=7 due to the dissociation of ionic bonds. The swelling ratio of the semi‐IPN hydrogels was pH, ionic concentration, temperature, and electric field dependent. Differential scanning calorimetry (DSC) was used to determine the volume of free water in the semi‐IPN hydrogels, which was found to increase with increasing PAAm content.     

Morphological and mechanical properties of tannic acid/PAAm semi-IPN hydrogels for cell adhesion

A series of hydrogels were fabricated from tannic acid (TA), a typical plant polyphenol widely present in wood, and polyacrylamide (PAAm) by semi-IPN and cryogelation techniques. The introduction of TA into the PAAm network endows the system with enhanced cell adhesion properties. The cryogels with open interconnected macropores had a superfast swelling rate and a high swelling ratio, as well as high elasticity in response to compression. The degradation of the hydrogels can be tuned by modulating the content of cross-linker poly(ethylene glycol) diacrylate (PEGDA). Cytotoxicity results revealed that the hydrogels were non-toxic to COS-7 cells. All these results suggested that TA/PAAm semi-IPN hydrogels have great potential for applications in tissue engineering.     

Synthesis and characterization of novel biodegradable unsaturated poly(ester amide)/poly(ethylene glycol) diacrylate hydrogels

A series of novel biodegradable hydrogels were designed and synthesized from four types of unsaturated poly(ester amide) (UPEA) and poly(ethylene glycol) diacrylate (PEG‐DA) precursors by UV photocrosslinking. These newly synthesized biodegradable UPEA/PEG‐DA hydrogels were characterized by their gel fraction (G_f), equilibrium swelling ratio (Q_eq), compressive modulus, and interior morphology. The effect of the precursor feed ratio (UPEAs to PEG‐DA) on the properties of the hydrogels was also studied. The incorporation of UPEA polymers into the PEG‐DA hydrogels increased their hydrophobicity, crosslinking density (denser network), and mechanical strength (higher compressive modulus) but reduced Q_eq. When different types of UPEA precursors were coupled with PEG‐DA at the same feed ratio (20 wt %), the resulting hydrogels had similar Q_eq values and porous three‐dimensional interior morphologies but different G_f and compressive modulus values. These differences in the hydrogel properties were correlated to the chemical structures of the UPEA precursors; that is, the different locations of the >C?C< double bonds in individual UPEA segments resulted in their different reactivities toward PEG‐DA to form hydrogels. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3932–3944, 2005     

The influence of diffusion time on the properties of sequential interpenetrating PEG hydrogels

Four sets comprising a total of 16 sequential interpenetrating network (SeqIPN) hydrogels were efficiently fabricated via UV initiated thiol‐ene coupling chemistry and from 2 kDa or 8 kDa primary poly(ethylene glycol) (PEG) networks (S2 and S8). Each primary system delivered four different SeqIPNs constructed after 2, 4, 20, and 44 h diffusion of secondary network PEG precursors, 2 kDa and 8 kDa. This allowed the assessment of both mechanical and swelling properties for a wide range of novel hydrogels ranging from loosely crosslinked SeqIPN 8‐8 to densely crosslinked SeqIPN 2‐2 systems. All gel fractions of secondary networks were above 83% and 44 h of diffusion was found sufficient to fully saturate the primary networks. Disperse red functionalized PEGs (2 kDa and 8 kDa) were further used as probes to investigate the diffusion mechanisms. The impact of diffusion time on loosely crosslinked S8 network with a swelling degree of 970% and tensile modulus of 175 kPa displayed a significant change in the final properties. For instance, a 2 h diffusion of 2 kDa PEG precursors generated a SeqIPN 8‐2:2 comprising a secondary network solid content of 34% with a water swelling degree 580% and a tensile modulus of 365 kPa. On saturation, that is, 44 h of diffusion, SeqIPN 2‐8:44 exhibited 64% of secondary network solid content, a swelling capacity of 380% and over fourfold of tensile modulus (758 kPa) when compared with the primary network S8. SeqIPN hydrogel with the highest tensile modulus and lowest degree of water swelling was obtained after 44 h diffusion of 2 kDa PEG precursors within the densely crosslinked S2 primary network. In this case, SeqIPN 2‐2:44 noted a water swelling capability of 280% and a tensile modulus over 1 MPa. The latter was twofold when compared with S2 with a tensile modulus of 555 kPa. Consequently, the diffusion time of secondary network is a promising parameter to control and that enables the fabrication of PEG hydrogels with a wider window of mechanical and swelling properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and physicochemical characterization of biodegradable and pH‐responsive hydrogels based on polyphosphoester for protein delivery

In this work, a series of biodegradable and pH‐responsive hydrogels based on polyphosphoester and poly(acrylic acid) are presented. A novel biodegradable macrocrosslinker α‐methacryloyloxyethyl ω‐acryloyl poly(ethyl ethylene phosphate) (HEMA‐PEOP‐Ac) was synthesized by first ring‐opening polymerization of the cyclic monomer 2‐ethoxy‐2‐oxo‐1,3,2‐dioxaphospholane using HEMA as the initiator and Sn(Oct)₂ as catalyst, and subsequent conversion of hydroxyl into vinyl group. The hydrogels were then fabricated by the copolymerization of the macromonomer with acrylic acid, and their swelling/deswelling and degradation behaviors were investigated. The results demonstrated that the crosslinking density and pH values of media strongly influenced both the swelling ratio and the degradation rate of the hydrogels. The rheological properties of these hydrogels were also studied from which the storage modulus (G′) showed clear dependence on the crosslinking density. MTT and “live/dead” assay showed that these hydrogels were compatible to fibroblast cells, not exhibiting apparent cytotoxicity even at high concentrations. Moreover, in vitro bovine serum albumin release from these hydrogels was also investigated, and it could be found that the release profiles showed a burst effect followed by a continuous release phase, and the release rate was inversely proportional to the crosslinking density of hydrogels. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1919–1930, 2010     

Swelling behavior and network structure of hydrogels synthesized using controlled UV‐initiated free radical polymerization

N‐vinyl‐2‐pyrrolidone (VP) and 2‐hydroxyethyl methacrylate (HEMA) copolymeric gels have been synthesized using UV‐initiated photopolymerization to understand their characteristic behavior for development as a bioengineering material, specifically for tissue expansion. The properties of the gels have been investigated by systematic variation of the monomer feed composition and initiator and crosslinker concentrations as well as UV irradiation intensity, which was controlled by various photomasks. The swelling kinetics and network characteristics for the various hydrogels were investigated through the observation of gel swelling behavior in saline solutions and compression modulus determination of the fully swollen hydrogels. The equilibrium swelling ratio (q_e) of the gels increased as expected with increasing VP content and decreasing crosslinker concentration. However, it was found that as the amount of initiator or UV intensity increased, unexpectedly q_e also increased, which indicates a network structure with decreasing effective crosslink density (ν_e) (or increasing average molecular weight between crosslinks (M_c)). Based on this anomalous swelling behavior and thermal analysis of the gels, a molecular structure is proposed consisting of increasing number of dangling chain ends within the polymer network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1450–1462, 2008     

Swelling and contraction of ferrogels based on polyacrylamide in a magnetic field

The equilibrium swelling of magnetoactive ferrogels based on the copolymer of acrylamide with 10% potassium acrylate in water is studied. The gels are filled with strontium ferrite and/or magnetite taken in amounts of 20, 40, 60, and 80 parts per 100 parts of the polymer by weight. In the absence of a magnetic field, as the content of the filler is increased, the degree of swelling tends to increase for the gels containing strontium ferrite and to decrease for the magnetite-containing gels. In the structure of hydrogels, strontium ferrite particles possessing a permanent magnetic moment form a microscopic network from chain aggregates, while the particles of magnetite, a magnetically soft material, give rise to disordered aggregates. The enthalpy of hydration of ferrogel polymeric matrices weakly depends on the nature and amount of the introduced filler: The interaction parameter takes small positive values in the range 0.10–0.18. In a homogeneous magnetic field of 365 mT, the degree of swelling decreases at a small filler content for both types of ferrogels. This effect is accompanied by elongation of a ferrogel sample along the field direction and contraction in the transverse direction. With an increase in the filler content, the inversion of both effects occurs. The applicability of concepts about the homogeneously magnetizable continuous medium to the process of magnetostriction of ferrogels is analyzed.     

Hydrogen bond-reinforced double-network hydrogels with ultrahigh elastic modulus and shape memory property

Development of tough hydrogels has greatly expanded their applications as load-bearing materials. However, the elastic modulus of tough hydrogels is usually lower than 1 MPa. It remains a challenge to design tough hydrogels with high modulus. We report here a series of tough double-network (DN) hydrogels with ultrahigh elastic modulus (up to 200 MPa) by forming robust hydrogen bonds between the first poly(acrylic acid) network and the second poly(N-isopropyl acrylamide) network. The dense cooperative hydrogen bonds greatly reduce the segmental mobility and thus improve the rigidity of gel matrix. Owing to the dynamic nature of hydrogen bonds, the modulus of hydrogels is strongly influenced by temperature and pH, affording the gels shape memory property. The strategy by forming robust noncovalent bonds between interpenetrating networks should be applicable to other systems for designing tough and versatile hydrogels with diverse promising applications. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1281–1286     

Preparation of interpenetrating polymer network composed of poly(ethylene glycol) and poly(acrylamide) hydrogels as a support of enzyme immobilization

Poly(ethylene glycol)(PEG)‐based interpenetrating polymeric network (IPN) hydrogels were prepared for the application of enzyme immobilization. Poly(acrylamide)(PAAm) was chosen as the other network of IPN hydrogel and different concentration of PAAm networks were incorporated inside the PEG hydrogel to improve the mechanical strength and provide functional groups that covalently bind the enzyme. Formation of IPN hydrogels was confirmed by observing the weight per cent gain of hydrogel after incorporation of PAAm network and by attenuated total reflectance/Fourier transform infrared (ATR/FTIR) analysis. Synthesis of IPN hydrogels with higher PAAm content produced more crosslinked hydrogels with lower water content (WC), smaller M_c and mesh size, which resulted in enhanced mechanical properties compared to the PEG hydrogel. The IPN hydrogels exhibited tensile strength between 0.2 and 1.2 MPa while retaining high levels of hydration (70–81% water). For enzyme immobilization, glucose oxidase (GOX) was immobilized to PEG and IPN hydrogel beads. Enzyme activity studies revealed that although all the hydrogels initially had similar enzymatic activity, enzyme‐immobilizing PEG hydrogels lost most of the enzymatic activity within 2 days due to enzyme leaching while IPN hydrogels maintained a maximum 80% of the initial enzymatic activity over a week due to the covalent linkage between the enzyme and amine groups of PAAm. Copyright © 2008 John Wiley & Sons, Ltd.     

Sequential interpenetrating poly(ethylene glycol) hydrogels prepared by UV‐initiated thiol–ene coupling chemistry

Poly(ethylene glycol) (PEG)‐diallyls, ranging from 2 to 8 kDa, were successfully reacted with a trifunctional thiol crosslinker via thiol–ene coupling reaction to construct four different primary PEG hydrogels. These systems were used as scaffolds for the preparation of a library of sequential interpenetrating networks (SeqIPNs). The solid content of the secondary networks varied between 21 and 34% and was dependent on the length of the absorbing PEGs. The gel fractions for the IPNs were above 85%. Additionally, the lowest degree of swelling was found for the IPN based on 2‐kDa PEG (315%), whereas the 8‐kDa PEG IPN exhibited a value of 810%. The SeqIPN strategy facilitated hydrogel systems that cover a larger domain of tensile modulus (192–889 kPa) when compared with single hydrogel networks (175–555 kPa). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013