Characterization of CdS nanoparticles formed and aggregated in stearic acid Langmuir–Blodgett films by atomic force microscopy

Alternate films, which are composed of stearic acid and CdS nanoparticles were synthesized by exposing Langmuir–Blodgett (LB) films of cadmium stearate (CdSt₂) to H₂S gas at a pressure of 1 Torr. The changes of surface morphology of film with the increased reaction time were directly observed by atomic force microscopy for the first time. Before being exposed to H₂S, the surface of CdSt₂ LB film was homogeneous from microscale down to nanoscale, and it was observed that CdSt₂ molecules formed a well orderly rectangular herringbone lattice structure on the molecular scale. However, after being exposed to H₂S the ordered CdSt₂ molecules gradually changed into a disordered state, and eventually the LB film surface became rough with the apparent feature of bulk structures on the nanoscale. This change in the morphology can be attributed to the aggregation of buried CdS nanoparticles within LB films, which has been confirmed by a structured UV–visible absorption spectrum where the absorption edge is red-shifted about 0.7 eV with respect to bulk CdS. Finally, the aggregation mechanism of CdS in the LB film was analyzed.     

TiO2@CdS core–shell nanorods films: Fabrication and dramatically enhanced photoelectrochemical properties

In this paper, we prepared TiO₂@CdS core–shell nanorods films electrodes using a simple and low-cost chemical bath deposition method. The core–shell nanorods films electrodes were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV–vis spectrometry techniques. After applying these TiO₂@CdS core–shell nanorods electrodes in photovoltaic cells, we found that the photocurrent was dramatically enhanced, comparing with those of bare TiO₂ nanorods and CdS films electrodes. Moreover, TiO₂@CdS core–shell nanorods film electrode showed better cell performance than CdS nanoparticles deposited TiO₂ nanoparticles (P25) film electrode. A photocurrent of 1.31 mA/cm², a fill factor of 0.43, an open circuit photovoltage of 0.44 V, and a conversion efficiency of 0.8% were obtained under an illumination of 32 mW/cm², when the CdS nanoparticles deposited on TiO₂ nanorods film for about 20 min. The maximum quantum efficiency of 5.0% was obtained at an incident wavelength of 500 nm. We believe that TiO₂@CdS core–shell heterostructured nanorods are excellent candidates for studying some fundamental aspects on charge separation and transfer in the fields of photovoltaic cells and photocatalysis.     

Direct electrochemistry study of glucose oxidase on Pt nanoparticle-modified aligned carbon nanotubes electrode by the assistance of chitosan–CdS and its biosensoring for glucose

Aligned carbon nanotubes (ACNTs) electrode has been developed for the direct protein electrochemistry and enzyme-biosensor study involving two types of nanoparticles. Pt nanoparticles (Pt_nano) were electro-modified on the ACNTs’ each tube, greatly increasing the electrode surface area for locating protein and also its electronic transfer ability. Glucose oxidase (GOD) with chitosan (CS) and CdS nanoparticles electrochemically coated on each tube of ACNTs–Pt_nano by the electrodeposition reaction of CS when pH value passing its pKa. The CdS nanoparticles between ACNTs electrode and GOD have stimulated the GOD’s direct electron transfer during its redox reaction of FAD/FADH₂. The CS–GOD–CdS/ACNTs–Pt_nano electrode also offer sensitive response to the substrate of glucose with detection limit of 46.8 μM (S/N = 3) and apparent Michaelis–Menten constant of 11.86 mM.     

Electrochemically synthesized CdS nanoparticle-modified TiO2 nanotube-array photoelectrodes: Preparation,characterization, and application to photoelectrochemical cells

A novel electrodeposited CdS nanoparticle-modified highly-ordered TiO₂ nanotube-array photoelectrode and its application to photoelectrochemical cells is reported. Results show formation of a thin, nanoparticulate CdS layer, comprised of sphere-like 10–20 nm diameter nanoparticles, on the anodic synthesized TiO₂ nanotube-array (inner diameter of 70 nm, wall thickness 25 nm and ca. 400 nm length) electrode. The resulting CdS–TiO₂ photoelectrode has an as-fabricated bandgap of 2.53, and 2.41 eV bandgap after sintering at 350 °C in N₂ ambient. Photoelectrochemical properties are described in detail.     

Photoelectrochemical determination of inorganic mercury ions based on energy transfer between CdS quantum dots and Au nanoparticles

A novel photoelectrochemical (PEC) sensor for mercury ions (Hg^2 +) was fabricated based on the energy transfer (ET) between CdS quantum dots (QDs) and Au nanoparticles (NPs) with the formation of T–Hg^2 +–T pairs. In the presence of Hg^2 + ions, a T-rich single-strand (ss) DNA labeled with Au NPs could hybridize with another T-rich ssDNA anchored on the CdS QDs modified electrode, through T–Hg^2 +–T interactions, rendering the Au NPs in close proximity with the CdS QDs and hence the photocurrent decrease due to the ET between the CdS QDs and the Au NPs. Under the optimal condition, the photocurrent decrease was proportional to the Hg^2 + concentration, ranging from 3.0 × 10^− 9 to 1.0 × 10^− 7 M, with the detection limit of 6.0 × 10^− 10 M.     

Effect of Hg2+doping and of the annealing temperature on the nanostructural properties of TiO2 thin films obtained by sol–gel method

This work is a study of Hg²⁺-doped TiO₂ thin films deposited on silicon substrates prepared by sol–gel method and treated at temperatures ranging between 600 to 1000 °C for 2 h. The structural and optical properties of thin films have been studied using different techniques. We analyzed the vibrations of the chemical bands by Fourier transform infrared (FTIR) spectroscopy and the optical properties by UV–Visible spectrophotometry (reflection mode) and photoluminescence (PL). The X-ray diffraction and Raman spectra of TiO₂ thin films confirmed the crystallization of the structure under the form of anatase, rutile, mercury titanate (HgTiO₃) as a function of the annealing temperature. The observation by scanning electron microscopy (SEM) showed the changing morphology, with respect to nanostructures, nanosheets, nanotubes, with the annealing temperature. The diameters of nanotubes ranged from 50 nm to 400 nm. The photoluminescence and reflectance spectra indicated that these structures should enhance photocatalytic activity.     

Chemical bath deposition of CdS quantum dots on vertically aligned ZnO nanorods for quantum dots-sensitized solar cells

Formation of CdS quantum dots (Q dots) on the vertically aligned ZnO nanorods electrode was carried out by chemical bath deposition. The diameter and thickness of ZnO nanorods are ～100–150 nm and ～1.6 μm, respectively, and CdS Q dots on ZnO nanorods have a diameter of smaller than 15 nm. In application of the Q dots-sensitized solar cells, composite film exhibited a power conversion efficiency of 0.54% under air mass 1.5 condition (80 mW/cm²), and incident-photon-to-current conversion efficiency showed 18.6%.     

Self-assembled Nafion–silica nanoparticles for elevated-high temperature polymer electrolyte membrane fuel cells

In this paper, a novel Nafion/SiO₂ nanocomposite membrane based on the self-assembled Nafion–SiO₂ nanoparticles was developed. The average particle size of Nafion–SiO₂ nanoparticles prepared by self-assembly process was 2.8 ± 0.5 nm. The self-assembled Nafion–SiO₂ nanoparticles significantly enhance the durability of the Nafion/silica nanocomposite membrane as compared to that of conventional Nafion/silica composite and Nafion 212 membranes under wet/dry cyclic tests at 90 °C. With an addition of 5 wt% self-assembled Nafion–SiO₂ nanoparticles, the Nafion/SiO₂ nanocomposite membrane shows a significantly improved performance stability at cell/humidifying temperatures of 100 °C/60 °C under a current density of 600 mA/cm², and the degradation rate is 0.12 mV/min, almost 20 times lower than 2.33 mV/min measured on the pristine Nafion 212 membrane under the same conditions. The present results demonstrate the promises of the self-assembled Nafion/SiO₂ nanocomposite membrane for elevated-high temperature PEM fuel cells applications.     

Synthesis of ZnS nanoparticles from pyridine adducts of zinc(II) dithiocarbamates

Zn(thqdtc)₂, Zn(thqdtc)₂(py) and Zn(thiqdtc)₂(py) (where thqdtc = 1,2,3,4-tetrahydroquinolinecarbodithioate, thiqdtc = 1,2,3,4-tetrahydroisoquinolinecarbodithioate and py = pyridine) have been used as single source precursors for the synthesis of ZnS nanoparticles. The formation of ZnS nanoparticles was achieved by thermal decomposition of the complex under heating in presence of triethylenetetraamine. Transmission electron microscopy, energy dispersive X-ray analysis (EDAX) and powder X-ray diffraction studies were carried out to study the structure and morphology of the nanoparticles. The optical properties of the ZnS nanoparticles were studied by UV–visible and fluorescence emission spectral studies. UV–visible absorption spectral studies indicate a blue shift in the absorption maxima due to the quantum size effect. A single crystal X-ray analysis was carried out for a precursor [Zn(thqdtc)₂].     

Iron (III) nanocomposites for enzyme-less biomimetic cathode: A promising material for use in biofuel cells

In this paper, we discuss the synthesis and electrochemical properties of a new material based on iron oxide nanoparticles stabilized with poly(diallyldimethylammonium chloride) (PDAC); this material can be used as a biomimetic cathode material for the reduction of H₂O₂ in biofuel cells. A metastable phase of iron oxide and iron hydroxide nanoparticles (PDAC–FeOOH/Fe₂O₃-NPs) was synthesized through a single procedure. On the basis of the Stokes–Einstein equation, colloidal particles (diameter: 20 nm) diffused at a considerably slow rate (D = 0.9 × 10^? 11 m s^? 1) as compared to conventional molecular redox systems. The quasi-reversible electrochemical process was attributed to the oxidation and reduction of Fe³⁺/Fe²⁺ from PDAC–FeOOH/Fe₂O₃-NPs; in a manner similar to redox enzymes, it acted as a pseudo-prosthetic group. Further, PDAC–FeOOH/Fe₂O₃-NPs was observed to have high electrocatalytic activity for H₂O₂ reduction along with a significant overpotential shift, ΔE = 0.68 V from ? 0.29 to 0.39 V, in the presence and absence of PDAC–FeOOH/Fe₂O₃-NPs. The abovementioned iron oxide nanoparticles are very promising as candidates for further research on biomimetic biofuel cells, suggesting two applications: the preparation of modified electrodes for direct use as cathodes and use as a supporting electrolyte together with H₂O₂.     

Green synthesis of plant-stabilized Au nanoparticles for the treatment of gastric carcinoma

In this study, gold nanoparticles (AuNPs) were green synthesized using plant extract. The obtained nanoparticles (Au NPs) were characterized by advanced physical and chemical techniques like TEM, FTIR, UV–vis, SEM, XRD and EDX. SEM image displayed the quasi-spherical shaped nanoparticles of mean diameter 20–50 nm. All the particles were of uniform shape and texture. From the XRD pattern, four distinct diffraction peaks at 38.2°, 44.2°, 64.7° and 77.4° are indexed as (1 1 1), (2 0 0), (2 2 0) and (3 1 1) planes of fcc metallic gold. The in vitro cytotoxic and anti-gastric carcinoma effects of biologically synthesized Au NPs against cancer cell lines were assessed. The IC₅₀ of the Au NPs were 192, 149, 76 and 85 µg/mL against NCI-N87, MKN45, GC1401 and GC1436 gastric cancer cell lines. The anti-gastric carcinoma properties of the Au NPs could significantly remove the cancer cell lines in a time and concentration-dependent manner. So, the findings of the recent research show that biologically synthesized Au NPs might be used to cure cancer.     

Thin films composed of irregular micro-block arrays of closely packed CdS nanoparticles for enhanced photoelectrochemical performance

CdS is a very important semiconductor, and various micro-/nano-structured forms of CdS have been fabricated with the aim of improving its photoelectrochemical performance. We report here for the first time the preparation of a CdS film consisting of irregular micro-block arrays of closely packed CdS nanoparticles. It performs outstandingly well as a photoanode because it possesses the advantages of both arrays and nanoparticles. This CdS film is prepared simply by a combination of reaction and assembly at the gas/liquid interface (RAG/L) with successive ionic layer adsorption and reaction (SILAR), requiring no templates or expensive equipment. In this approach, the nanopores in the film of loosely aggregated CdS nanoparticles produced by RAG/L are filled by CdS nanoparticles via SILAR, forming a compact CdS film. Network micro-cracks form in the compact CdS film due to calcination caused by differential thermal expansion compared with the substrate, and these cut the CdS film into irregular micro-block arrays. This micro-/nano-structure in the prepared CdS film improves its capacity for visible light absorption, facilitates the generation/separation of excited charges, and enhances mass transfer. In an alkaline solution of methanol, the prepared CdS film exhibits the highest saturation photocurrent density (6.5 mA cm^− 2) ever reported on CdS-based photoanodes under visible light illumination.     

Molecular patterning with a two-dimensional network polymer LB film 2: Drawing patterns by an electron beam

Electron beam lithography was investigated using a cross-linkable polymer Langmuir–Blodgett (LB) film. Cross-linking reaction occurs in the LB film with electron beam irradiation as well as UV light irradiation and the irradiated LB film becomes insoluble in the organic solvents to form a two-dimensional network in the LB film. The sensitivity and contrast of the cross-linkable polymer LB film are 3 μC cm^-2 and 0.64, respectively. The limiting resolution of patterning is 0.2 μm line-and-space. The electron beam lithography using the cross-linkable polymer LB film is applicable to the future nanotechnology.     

Ag2S quantum dot-sensitized solar cells

We present a new photosensitizer – Ag₂S quantum dots (QDs) – for solar cells. The QDs were grown by the successive ionic layer adsorption and reaction deposition method. The assembled Ag₂S-QD solar cells yield a best power conversion efficiency of 1.70% and a short-circuit current of 1.54 mA/cm² under 10.8% sun. The solar cells have a maximal external quantum efficiency (EQE) of 50% at λ = 530 nm and an average EQE of ～ 42% over the spectral range of 400–1000 nm. The effective photovoltaic range covers the visible and near-infrared spectral regions and is ～ 2–4 times broader than that of the cadmium chalcogenide systems — CdS and CdSe. The results show that Ag₂S QDs can be used as a highly efficient and broadband sensitizer for solar cells.     

Kinetics of the diazotization and azo coupling reactions of procaine in the micellar media

The kinetics of the diazotization reaction of procaine in the presence of anionic micelles of sodium dodecyl sulfate (SDS) and cationic micelles of cetyltrimethyl ammonium bromide (CTAB), dodecyltrimethyl ammonium bromide (DDTAB) and tetradecyltrimethyl ammonium bromide (TDTAB) were carried out spectrophotometrically at λ_max = 289 nm. The values of the pseudo first order rate constant were found to be linearly dependent upon the [NaNO₂] in the concentration range of 1.0 × 10⁻³ mol dm⁻³ to 12.0 × 10⁻³ mol dm⁻³ in the presence of 2.0 × 10⁻² mol dm⁻³ acetic acid. The concentration of procaine was kept constant at 6.50 × 10⁻⁵ mol dm⁻³. The addition of the cationic surfactants increased the reaction rate and gave plateau like curve. The addition of SDS micelles to the reactants initially increased the rate of reaction and gave maximum like curve. The maximum value of the rate constant was found to be 9.44 × 10⁻³ s⁻¹ at 2.00 × 10⁻³ mol dm⁻³ SDS concentration. The azo coupling of diazonium ion with β-naphthol (at λ_max = 488) nm was found to linearly dependent upon [ProcN₂⁺] in the presence of both the cationic micelles (CTAB, DDTAB and TDTAB) and anionic micelles (SDS). Both the cationic and anionic micelles inhibited the rate of reactions. The kinetic results in the presence of micelles are explained using the Berezin pseudophase model. This model was also used to determine the kinetic parameters e.g. k_m, K_s from the observed results of the variation of rate constant at different [surfactants].     

Synthesis of hybrid solar cells using CdS nanowire array grown on conductive glass substrates

High-density CdS nanowire (NW) arrays were successfully grown on fluorine-doped tin oxide (FTO)-coated glass substrates by vapor–liquid–solid (VLS) mechanism at a remarkably reduced temperature of ～450 °C. Bi catalyst layer and polyvinyl alcohol (PVA) played a major role in the low-temperature synthesis of high-quality CdS NW arrays. CdS NWs were defect free single crystalline Wurtzite crystals and they were 50–100 nm and 2–5 μm in diameter and length, respectively. CdS NWs were combined with poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV), a conjugated polymer to form organic–inorganic hybrid structures. The UV–visible light absorption and emission behavior of MEH-PPV/CdS hybrids was investigated and their potential to be used as photovoltaic cells was demonstrated.     

Dual-response nanocarrier based on graft copolymers with hydrazone bond linkages for improved drug delivery

Core–shell micelles with biodegradability, thermo- and pH-response were successfully demonstrated by poly(2-oxepane-1,5-dione-co-ɛ-caprolactone) (P(OPD-co-CL)) grafted with hydrophilic segments of amine-terminated poly(N-isopropylacrylamide) (At-PNIPAM). To compare with the graft copolymer, P(OPD-co-CL) block PNIPAM polymer was also prepared. The micelles with core–shell structure were formed with both graft and block copolymers by self-assembly in aqueous solutions, of which PNIPAM shell is thermo-response. Furthermore, P(OPD-co-CL)-g-PNIPAM also showed pH-sensitivity, which was attributed to the acid-cleavable property of the hydrazone bond. The low critical micelle concentrations (CMCs) of graft polymers and block polymers were 6.7 mg/L and 14.3 mg/L, respectively, which indicated the formation of stable micelles. Both drug-free and drug-loaded micelles were in uniformly spherical shape observed by transmission electron microscopy (TEM). The sizes of the drug-free and drug-loaded micelles prepared from graft polymer were 123.5 nm and 146.5 nm, respectively, and the sizes of those prepared from block polymer were 197.5 nm and 211.5 nm, respectively. The lower critical solution temperature (LCST) for the graft polymer was 34.3 °C, while that for the block polymer was 28.1 °C, demonstrating a thermo-response. The graft polymeric micelles exhibited thermo-triggered decelerated release at pH 7.4, and pH-triggered accelerated release at 25 °C in vitro release test, indicating that the graft polymeric micelles could be a promising site-specific drug delivery system for enhancing the bioavailability of the drug in targeted pathological areas.     

The performance of coupled (CdS:CdSe) quantum dot-sensitized TiO2 nanofibrous solar cells

Highly porous networks and reduced grain boundaries with one-dimensional (1-D) nanofibrous morphology offer enhanced charge transport in solar cells applications. Quantum dot (QDs) decorated TiO₂ nanofibrous electrodes, unlike organic dye sensitizers, can yield multiple carrier generations due to the quantum confinement effect. This paper describes the first attempt to combine these two novel approaches, in which CdS (～18 nm) and CdSe (～8 nm) QDs are sensitized onto electrospun TiO₂ nanofibrous (diameter ～80–100 nm) electrodes. The photovoltaic performances of single (CdS and CdSe) and coupled (CdS/CdSe) QDs-sensitized TiO₂ fibrous electrodes are demonstrated in sandwich-type solar cells using polysulfide electrolyte. The observed difficulties in charge injection and lesser spectral coverage of single QDs-sensitizers are solved by coupling (CdS:CdSe) two QDs-sensitizers, resulting in a enhanced open-circuit voltage (0.64 V) with 2.69% efficiency. These results suggest the versatility of fibrous electrodes in QDs-sensitized solar cell applications.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

AgSbS2 semiconductor-sensitized solar cells

We present a ternary semiconductor nanoparticle sensitizer – AgSbS₂ – for solar cells. AgSbS₂ nanoparticles were grown using a two-stage successive ionic layer adsorption and reaction process. First, Ag₂S nanoparticles were grown on the surface of a nanoporous TiO₂ electrode. Secondly, a Sb–S film was coated on top of the Ag₂S. The double-layered structure was transformed into AgSbS₂ nanoparticles ~ 40 nm in diameter, after post-deposition heating at 350 °C. The AgSbS₂-sensitized TiO₂ electrodes were fabricated into liquid-junction solar cells. The best cell yielded a power conversion efficiency of 0.34% at 1 sun and 0.42% at 0.1 sun. The external quantum efficiency (EQE) spectrum covered the range of 380–680 nm with a maximal EQE of 10.5% at λ = 470 nm. The method can be applied to grow other systems of ternary semiconductor nanoparticles for solar absorbers.