Cellulosic nanocomposite membranes from hydroxypropyl cellulose reinforced by cellulose nanocrystals

Cellulosic nanocomposite membranes were prepared by incorporation of cellulose nanocrystals (CNCs) into a hydroxypropyl cellulose (HPC) matrix using a mixing/evaporation technique. CNCs were obtained from filter paper using the sulfuric acid hydrolysis method with the aid of ultrasonication. The relationship between the microstructure and mechanical properties of the CNCs/HPC nanocomposite membranes was studied. Scanning electron microscopy showed that the CNCs were well dispersed in the HPC matrix, and the fracture surface demonstrated a fibrous characteristic. With increasing CNCs content, the tensile strength and Young’s modulus of the CNCs/HPC nanocomposite membranes gradually increased. At 5 wt% content of CNCs, the strength was increased by 525 % and the Young’s modulus by 124 % compared with pure HPC membrane. Moreover, the effect of the phase change of HPC on the mechanical properties of the CNCs_5wt%/HPC nanocomposite membranes and the corresponding mechanism were also studied.     

High-performance natural rubber nanocomposites with marine biomass (tunicate cellulose)

Due to the importance in economic and environmental benefits, marine biomass has gained increasing attention in recent years. In this work, marine biomass-based materials were prepared and characterized. Highly reinforcing cellulose nanocrystals (CNCs) with length of 1–2 μm and aspect ratio of ~75 were extracted from tunicates (t-CNCs), and CNCs with length of 100–300 nm and aspect ratio of ~15 from cotton (c-CNCs) were presented for comparison. In order to enhance interfacial interactions between CNCs and rubber, modification of natural rubber (NR) was conducted via epoxidation reaction to obtain epoxidized NR (ENR). Fully bio-based rubber nanocomposites were produced by latex mixing. Compared with NR nanocomposites, hydrogen bonding formed between ENR and CNCs, which led to homogeneous dispersion of CNCs and enhanced interfacial adhesion between them. Moreover, t-CNCs with longer length and larger aspect ratio facilitate filler entanglements, which led to higher reinforcing efficiency. Consequently, both hydrogen bonding and filler entanglements contributed to the improved mechanical properties of ENR/t-CNCs nanocomposites.     

Physicomechanical properties of nanocomposites based on cellulose nanofibre and natural rubber latex

Cellulose nanofibres (CNF) with diameter 10–60 nm were isolated from raw banana fibres by steam explosion process. These CNF were used as reinforcing elements in natural rubber (NR) latex along with cross linking agents to prepare nanocomposite films. The effect of CNF loading on the mechanical and dynamic mechanical (DMA) properties of NR/CNF nanocomposite was studied. The morphological, crystallographic and spectroscopic changes were also analyzed. Significant improvement of Young’s modulus and tensile strength was observed as a result of addition of CNF to the rubber matrix especially at higher CNF loading. DMA showed a change in the storage modulus of the rubber matrix upon addition of CNF which proves the reinforcing effect of CNF in the NR latex. A mechanism is suggested for the introduction of the Zn–cellulose complex and its three dimensional network as a result of the reaction between the cellulose and the Zinc metal which is originated during the composite formation.     

Studies of vulcanization with tetramethylthiuram disulfide and sulfur vulcanization accelerated by tetramethylthiuram disulfide of styrene–butadiene rubber in presence and absence of dicumyl peroxide

The salient features of nonelemental sulfur vulcanization by tetramethylthiuram disulfide (TMTD) and elemental sulfur vulcanization promoted by TMTD both in presence and absence of ZnO and stearic acid have been studied. In stock containing TMTD, a higher rate constant value for dicumyl peroxide (DCP) decomposition was observed. TMTD decreases the crosslinking density due to DCP depending on its concentration. An entirely radical mechanism has been advanced in the absence of ZnO. ZnO or ZnO–stearic acid seems to alter the entire course of reaction. The rate of crosslinking increases in the presence of ZnO or ZnO–stearic acid. Moreover, crosslinks are formed additively (further supported from the activation energy data), and mixed crosslink formation has been confirmed by the methyl iodide test of the vulcanizates. Stearic acid has no effect on crosslink formation. An ionic chain mechanism has been postulated in the presence of ZnO, as suggested by British authors.     

Tough nanocomposite hydrogels from cellulose nanocrystals/poly(acrylamide) clusters: influence of the charge density,aspect ratio and surface coating with PEG

Cellulose-derived materials are usually characterized by sophisticated structures, leading to unique and multiple functions, which have been a source of inspiration for the fabrication of a wide variety of nanocomposites. Cellulose nanocrystals/poly(acrylamide) (CNCs/PAM) nanocomposite hydrogels were synthesized via in situ polymerization in the CNC suspension. The cellulose from pulp fiber under different sulfuric acid hydrolysis conditions, examined by conductometric titration and transmission electron microscopy, was applied to study how the effects of the surface charge and aspect ratio affect CNCs’ mechanical reinforcement in nanocomposites. The results indicated that the higher surface charge concentration resulted in better dispersibility in aqueous suspension, leading to a more efficient energy dissipation process. The CNC reinforcement behavior followed the percolation model where the greater aspect ratio of CNC contributed to higher mechanical properties. The preferential adsorption of poly(ethylene glycol) (PEG) on the CNC surface was characterized by zeta potential measurements where the fracture strength and fracture elongation of nanocomposites decreased with increasing PEG concentration. The adsorption of PEG on the CNC surface occupied the active sites for polymer chain propagation, which hindered the PAM cross-linking effect on the CNC surface and decreased the cross-linking density of the network.     

COORDINATION CROSSLINKING OF NITRILE RUBBER FILLED WITH COPPER SULFATE PARTICLES

By incorporating copper sulfate(CuSO_4)particles into acrylonitrile butadiene rubber(NBR)followed by heat pressing,a novel vulcanization method is developed in rubber through the formation of coordination crosslinking.This method totally differs from traditional covalent or non-covalent vulcanization approaches of rubber.No other vulcanizing agent or additional additive is involved in this process.By analyzing the results of DMA,XPS and FT-IR,it is found that the crosslinking of CuSO_4 particles filled NBR was induced by in situ coordination between nitrogen atoms of nitrile groups (-CN)and copper ions(Cu~(2 ))from CuSO_4.SEM and EDX results revealed the generation of a core(CuSO_4 solid particle)- shell(adherent NBR)structure,which leads to a result that the crosslinked rubber has excellent mechanical properties. Moreover,poly(vinyl chloride)(PVC)and liquid acrylonitrile-butadiene rubber(LNBR)were used as mobilizer to improve the coordination crosslinking of CuSO_4/NBR.The addition of PVC or LNBR could lead to higher crosslink density and better mechanical properties of coordination vulcanization.In addition,crystal water in CuSO_4 played a positive role to coordination crosslinking of rubber because it decreased the metal point of CuSO_4 and promoted the metal ionization.     

Effect of nanocrystalline cellulose on the curing characteristics and aging resistance properties of carbon black reinforced natural rubber

This work focused on the effect of nanocrystalline cellulose (NCC) on the curing characteristics, aging resistance and thermal stability of natural rubber (NR) reinforced with carbon black (CB). Sharing the same fillers loading of 45 parts per hundred rubber (phr), NR/NCC/CB composites with different NCC/CB ratios (i.e. 0/45, 5/40, 10/35, 15/30, 20/25 phr) were prepared and analyzed. Resorcinol and hexamethylene tetramine (RH), acting as the modifier in NR/NCC interface, was also discussed for its influence. The result showed that an relatively higher ratio of NCC/CB led to a lower torque, a shorter cure time (T ₉₀), a slightly longer scorch time (T ₁₀) and a bigger vulcanization rate constant (K). This tendency suggested that the existence of NCC accelerated the vulcanization process. Additionally, modified by RH, NR/NCC/CB compounds exhibited a short T ₁₀ and a elevated torque. And a moderate RH content would lower the E _a of vulcanization. A 10 phr substitute of CB by NCC can help to improve aging resistance in terms of mechanical properties. In a high temperature aging condition, composites with 10 phr NCC also performed the highest storage modulus (G′) among composites tested. A moderate NCC content contributed to the best retention of G′ after high temperature aging, so did the incorporation of RH. With the partial replacement of CB by NCC, the temperature of 5% weight-lose had a slight drop and the apparent crosslink density showed a decrease. Thanks to the interaction of RH with both NR and NCC, composites showed an improvement in apparent crosslink density after modified by RH.     

Hybrid fluorescent nanoparticles from quantum dots coupled to cellulose nanocrystals

Carboxylated cellulose nanocrystals (CNCs) were decorated with CdSe/ZnS quantum dots (QDs) using a carbodiimide chemistry coupling approach. The one-step covalent modification was supported by nanoscale imaging, which showed QDs clustered on and around the CNCs after coupling. The QD–CNC hybrid nanoparticles remained colloidally stable in aqueous suspension and were fluorescent, exhibiting the broad excitation and narrow emission profile characteristic of the QDs. QD–CNCs in nanocomposite films imparted strong fluorescence within CNC-compatible matrices at relatively low loadings (0.15 nmol QDs/g of dry film), without altering the overall physical properties or self-assembly of the CNCs. The hybrid QD–CNCs may find applications in nanoparticle tracking, bio-imaging, optical/sensing devices, and anti-counterfeit technologies.     

Curcumin-loaded PLGA-PEG-PLGA triblock copolymeric micelles: Preparation, pharmacokinetics and distribution in vivo

Rod-shaped cellulose nanocrystals (CNCs) were manufactured and used to reinforce polyacrylamide (PAM) hydrogels through in situ free-radical polymerization. The gelation process of the nanocomposite hydrogels was monitored on a rheometer using oscillatory shear. The chemical structure, morphology, swelling property, and compression strength of the formed gels were investigated. A possible mechanism for forming hydrogels was proposed. The results showed that CNCs accelerated the formation of hydrogels and increased the effective crosslink density of hydrogels. Thus CNCs were not only a reinforcing agent for hydrogel, but also acted as a multifunctional cross-linker for gelation. The shear storage modulus, compression strength and elastic modulus of the nanocomposite hydrogels were significantly improved because of good dispersion of CNCs in PAM as well as enhanced interfacial interaction between these two components. Among the CNC contents used, a loading of 6.7 w/w% led to the maximum mechanical properties for nanocomposite hydrogels.     

Interplay of colloidal stability of cellulose nanocrystals and their dispersibility in cellulose acetate butyrate matrix

Cellulose nanocrystals (CNC) prepared from eucalyptus cellulose CNCs were modified by the reaction with methyl adipoyl chloride, CNCm, or with a mixture of acetic and sulfuric acid, CNCa. The CNC were either dispersed at 0.1 wt% in the pure solvents ethyl acetate (EA), tetrahydrofuran (THF) and dimethylformamide (DMF) or in cellulose acetate butyrate (CAB) solutions prepared in these solvents at 0.9 wt%. The colloidal behavior of these dispersions was systematically investigated using a phase separation analyzer LUMiReader^®. The mechanical properties and morphological features of the films resulting from the mixtures of CAB and CNC were determined by dynamic mechanical analysis, optical microscopy and atomic force microscopy, respectively. Regardless the functional group attached to the surface of CNC, the best colloidal stability was observed for dispersions prepared in CAB/DMF solution. Higher degree of substitution of modified CNCs favored the colloidal stability in EA and THF. Composite films prepared from CAB/DMF solutions were more homogeneous and presented better mechanical performance than those prepared in CAB/EA or CAB/THF. The mechanical performance of composites and neat CAB prepared from DMF was CAB/CNCs > CAB/CNCm > CAB/CNCa > CAB, indicating that the modification weakens the percolation process, which is mediated by H bonding.     

A model study on effect of glucose on the basic characteristics and physical properties of natural rubber

Glucose at various concentrations was incorporated into sugar free purified natural rubber (PNR) latex to model the effect of carbohydrate on the basic characteristics and physical properties of natural rubber (NR). PNR samples treated with various concentrations of glucose were characterized for the basic properties of unvulcanized NR, i.e., gel content, molecular weight distribution and Mooney viscosity to evaluate the effect of sugar on these parameters. In addition, the effect of glucose on the physical properties of vulcanizates derived using sulfur and peroxide vulcanization was investigated. Glucose was shown to affect the viscosity of unvulcanized NR and the discoloration of vulcanized NR. Moreover, glucose was found to have a strong effect on crosslink density, as well as tensile and dynamic properties of sulfur vulcanizates, while those properties of peroxide vulcanizates was not much affected by glucose.     

Analysis of the thermogenesis mechanism of natural rubber under high speed strain

This work highlights the relationship of crosslink density, entanglement points and various sulfide crosslinks with the thermogenesis properties of natural rubber (NR). The impact of cross‐link and entanglement on thermogenesis properties was evaluated by heat build‐up test, swelling behavior, statistical thermodynamic calculation, and classic viscoelastic theory. It was found that cross‐link and entanglement points have “pinning” effect to the rubber chain, thus remarkably restricting the motion of the rubber chain and reducing thermogenesis. Besides, the effects of various sulfide crosslinks and cross‐link length on thermogenesis were compared and discussed varying the sulfur vulcanization system. It was found that the semi‐effective vulcanization system using N‐cyclohexyl‐2‐benzothiazolesulfenamide (CZ) and 2‐Mercaptobenzothiazole (M) has the lowest thermogenesis (bottom temperature rise is 7.5°C, middle is 18.7°C), which on account of combined short crosslink length with high rigid rubber chain (crosslink network dominated by mono‐ and disulfides). As a result, the deformation degree of the rubber chain during curl up‐extension and the thermogenesis are further reduced. Finally, a combination of natural film coagulation and semi‐effective vulcanization system was used to prepare a low thermogenesis NR, in which bottom and middle temperature rise were only 5.0°C and 14.1°C, respectively.     

Preparation and properties of natural rubber composites reinforced with pretreated carbon nanotubes

In order to achieve dramatic improvements in the performance of rubber materials, the development of carbon nanotube (CNT)‐reinforced rubber composites was attempted. The CNT/natural rubber (NR) nanocomposite was prepared through solvent mixing on the basis of pretreatment of CNTs. Thermal properties, vulcanization characteristics, and physical and mechanical properties of the CNT/NR nanocomposites were characterized in contrast to the carbon black (CB)/NR composite. Through the addition of the CNTs treated using acid bath followed by ball milling with HRH (hydrated silica, resorcinol, and hexamethylene tetramine) bonding systems, the crystallization melting peak in differential scanning calorimetry (DSC) curves of NR weakened and the curing rate of NR slightly decreased. Meanwhile, the over‐curing reversion of CNT/NR nanocomposites was alleviated. The dispersion of the treated CNTs in the rubber matrix and interfacial bonding between them were rather good. The mechanical properties of the CNT‐reinforced NR showed a considerable increase compared to the neat NR and traditional CB/NR composite. At the same time, the CNT/NR nanocomposites exhibited better rebound resilience and dynamic compression properties. The storage modulus of the CNT/NR nanocomposites greatly exceeds that of neat NR and CB/NR composites under all temperature regions. The thermal stability of NR was also obviously improved with the addition of the treated CNTs. Copyright © 2008 John Wiley & Sons, Ltd.     

Ribbon-like microfiber of vulcanized and non-vulcanized natural rubber obtained by the solution blow spinning

Natural rubber (NR) microfibers were obtained from NR/chloroform solutions with or without vulcanization agents, by a solution blow spinning (SBS) technique. The microfibers showed a ribbon-like morphology with average widths ranging from 15 to 45 μm, depending on the processing conditions. Concentrations of 3%, 4%, and 5% (wt/vol) of NR/chloroform were compared; at 4% wt/vol the spinning process was most stable, and fiber width was the most homogeneous. Microfibrous NR membranes incorporating vulcanizing agents were treated at temperatures of 70, 80, and 90°C for 1, 2, 3, and 4 h. Membrane tensile strength and elongation at break varied with temperature and treatment time. The best result was found with the sample treated at 90°C for 3 h. In this case, the tensile strength and elongation at break was (4.9 ± 0.8) MPa and (867 ± 18) % which is about 310% and 330% higher than the values found for the same sample without the incorporation of vulcanizing agents. This expressive increase was attributed to the vulcanization of the rubber, which also provided a shift to a higher value of the glass transition temperature. Overall properties of the blow-spun films, especially the high elasticity-contraction, suggest they are attractive candidates for use in robotics, and biobased electronics including wearable sensors.     

Control of properties of nanocomposites bio-based collagen and cellulose nanocrystals

Collagen is an important biomaterial because it has many applications in the biomedical sector. However, the high hydrophilicity of collagen (COL) leads to easy swelling. Thus, controlling this property is highly desirable. In this work, cellulose nanocrystals (CNCs) dispersed in glycerol (GLI) were incorporated in the matrix collagen to tailor the hydrophilicity and mechanical properties. Study of the hydrophilicity of the bio-based nanocomposite was evaluated by contact angle measurement and thermogravimetric analysis. Mechanical analyses showed that CNCs are excellent reinforcing fillers to the collagen matrix. Synchrotron small-angle X-ray scattering was employed to investigate the nanostructures of COL/GLI/CNC nanocomposites and CNC water dispersion. CNC in concentrations up to 1 wt% presents an intermediate shape between a rod and a plane with a 9.34-nm radius of gyration (R _g). Bio-based nanocomposites present two different structural levels with two types of particles with very different R _gs. At the intermediate power-law regime, a large-scale mass fractal aggregate is observed. In the high-power-law regime, it is observed scattering from primary particles smaller than 1 nm. As the CNC concentration increases, the original particle distorts from a rod to a plate. The cytotoxicity assay indicates that the collagen and nanocomposites did not affect the cell viability of rat calvarial cells in vitro.     

Effects of pretreatments on crystalline properties and morphology of cellulose nanocrystals

Cellulose nanocrystals (CNCs) have drawn tremendous attention because of their extraordinary physical and chemical properties as well as renewability and sustainability. In this work, after a range of pretreatments, such as freeze-drying, ball-milling, mercerization, N-methylmorpholine-N-oxide dissolution and ionic liquid dissolution, various CNCs with different crystalline properties and morphologies were obtained by hydrolysis or oxidation. XRD and AFM were used to determine the influences of pretreatments on the crystalline properties and morphologies of CNCs. New methods, i.e., specific pretreatments followed by sulfuric acid hydrolysis or 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO) oxidation, were developed to obtain sphere-like CNCs. It was found that sphere-like CNCs were more likely to be obtained from cellulose materials possessing high accessibility. Pretreatments produced cellulose with various crystallinities and polymorphs, and therefore changed the yields of CNCs and influenced their morphology. CNCs prepared by TEMPO oxidation generally had smaller size than the corresponding products obtained by sulfuric acid hydrolysis. In addition, for the dissolved/regenerated cellulose, TEMPO oxidation was a better method to yield sphere-like CNCs than sulfuric acid hydrolysis.     

Reclaiming of ground rubber tire (GRT) by a novel reclaiming agent

The present paper describes the mechanical reclaiming of ground rubber tire (GRT) by tetra methyl thiuram disulfide (TMTD), a multi-functional reclaiming agent. The versatility of the proposed agent is that it acts as a reclaiming agent during reclaiming and as a curing agent during revulcanization of the reclaimed sample. Reclaiming of GRT was carried out on an open two roll mixing mill at various time intervals and different concentrations of the reclaiming agent (TMTD). The degree of reclaiming was evaluated by measurement of the gel content, inherent viscosity of sol rubber, Mooney viscosity of the reclaimed rubber, crosslink density, swelling ratio and molecular weight between two crosslink bonds as a function of milling time. Also, the influence of the gel content on crosslink density at various time intervals on the open two roll mixing mill was determined. A unique correlation between gel fraction and crosslink density obtained at various time intervals and concentrations of reclaiming agent indicated that an optimization of the concentration of TMTD and milling time has a positive influence on improving the efficiency of reclaiming. The reclaiming conditions have been optimized in view of the mechanical properties of the revulcanized GRT and the aging resistance properties of the revulcanized reclaim. The influence of the concentration of sulfur on the mechanical properties in the revulcanized reclaim was also studied. Scanning electron microscopy (SEM) studies further indicate the coherency and homogeneity in the revulcanized reclaim rubber when reclamation is carried out by optimum concentration of TMTD after maximum time of reclaiming.     

Poly(lactic acid)-based biocomposites reinforced with modified cellulose nanocrystals

This work investigates reinforcing poly(lactic acid) (PLA) nanocomposites using triazine derivative-grafted cellulose nanocrystals (CNCs). A hydrophobic triazine derivative was synthesized and applied to modify CNCs to improve their thermal stability and diminish the hydrophilicity of the nanoparticles. CNCs before and after modification were used to reinforce PLA nanocomposites by a hot compression process. The results of thermogravimetric analysis indicated that the initial thermal decomposition temperature of modified nanocrystals was improved by approximately 100 °C compared to the original CNCs. That is, the thermal stability of modified cellulose nanocrystals was improved due to the shielding effect of CNCs by a hydrophobic aliphatic amine layer on the surface of the nanoparticles. The results of dynamic contact angle measurements revealed a decrease of hydrophilicity of the modified CNCs. The results from scanning electron microscopy and a UV–Vis spectrophotometer revealed that the compatibility between the modified nanocrystals and the PLA was improved. Finally, the results of tensile tests indicated a significant improvement in terms of breaking strength and elongation at the break point.     

Investigation into morphology, microstructure and properties of SBR/EPDM/ORGANO montmorillonite nanocomposites

Rubber compounds based on styrene-butadiene rubber/ethylene propylene diene monomer blends of different compositions (60/40, 70/30, 80/20, 90/10, 100/0) reinforced with 1 wt%, 3 wt%, 5 wt% and 7 wt% organoclay (Cloisite 20A) were prepared on a two roll mill via a vulcanization process and characterized by several techniques. Results of X-ray diffraction showed expansion of the inter-gallery distance, and transmission electron microscopy (TEM) micrographs confirmed that the prepared nanocomposite samples have intercalated and partially exfoliated structures. Cure characteristics showed that, organoclay not only accelerates the vulcanization reaction, but also gives rise to a marked increase of the torque, indicating crosslink density of the prepared compounds increases at the presence of organoclay. Mechanical properties of samples received markedly increase by clay loading due to the good interaction established between nanoclay particles and polymer matrix as it was evidenced by SEM photomicrographs. At the same time, rheological properties showed that addition of nanoclay could improve storage modulus as well as complex viscosity of SBR/EPDM samples. The results of ozone test revealed that the ozone resistance of samples significantly increases as nanoclay or EPDM content increases.     

Prevulcanized natural rubber latex/clay aerogel nanocomposites

Natural rubber latex (NR)/clay aerogel nanocomposites were produced via freeze-drying technique. The pristine clay (sodium montmorillonite) was introduced in 1-3 parts per hundred rubber (phr) in order to study the effect of clay in the NR matrix. The dispersion of the layered clay and the morphology of the nanocomposites were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Cure characteristics, thermal stability, and the crosslink density of thermal and microwave-cured NR and its composites were investigated. XRD patterns indicated that both intercalated and exfoliated structures were observed at loadings of 1-3 phr clay. SEM studies revealed that the clay aerogel structure was formed at 3 phr clay loading. The increment in Shore A hardness of nanocomposites compared with pure NR signified excellent polymer/filler interaction and the reinforcing effect of the clay to rubber matrix. This was supported by an increase in maximum rheometric torque and crosslink density. The crosslink density of clay-filled NR vulcanizate was found to increase with the pristine clay content in both thermal and microwave curing methods. However, microwave-cured 2 and 3 phr-filled NR vulcanizates exhibited higher crosslink density than those which were thermal-cured under the same curing temperature. In addition, thermal stability studies showed that pristine clay accelerated the decomposition of NR by showing a slight decrease in onset and peak decomposition temperatures along with clay content.