Ferroelectric relaxor properties of (1 − x)K0.5Na0.5NbO3–xBa0.5Ca0.5TiO3 ceramics

The Ba_0.5Ca_0.5TiO₃ (BCT) composition dependent dielectric and structural properties of (1?x)K_0.5Na_0.5NbO₃–xBa_0.5Ca_0.5TiO₃ powders were investigated. Room temperature x-ray diffraction revealed the powder structure to transform from orthorhombic to cubic with increasing BCT composition. The frequency dependent dielectric constant measurements revealed a shift in the temperature of the maximum dielectric constant for at frequencies, suggesting that the system exhibits ferroelectric relaxor behavior. The system containing 15% BCT showed the closest calculated Curie–Weiss exponent to 2, which the exponent for a relaxor ferroelectric.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.     

Impedance spectroscopy and piezoresponse force microscopy analysis of lead-free (1 − x) K0.5Na0.5NbO3 − xLiNbO3 ceramics

(1 ? x) K_0.5Na_0.5NbO₃ ? xLiNbO₃ (where x = 0.0, 5.0, 5.5, 6.0, and 6.5 wt.%) (KNLN) perovskite structured ferroelectric ceramics were prepared by the solid-state reaction method. X-ray diffraction patterns indicate that single phase was formed for pure KNN while a small amount of second phase (K₆Li₄Nb₁₀O₃₀, ～3%) was present in LN doped KNN ceramics. Phase analysis indicated the change in the crystal structure from orthorhombic to tetragonal with increase in LN content. The electrical behavior of the ceramics was studied by impedance spectroscopy technique in the high temperature range. Impedance analysis was performed using an equivalent circuit model. The impedance response in pure KNN and KNLN ceramics could be deconvoluted into two contributions, associated with the bulk (grains) and the grain boundaries. Activation energies for conductivity were found to be strongly frequency dependent. The activation energy obtained from dielectric relaxation data was attributed to oxygen vacancies. From PFM we found that the composition with 6.5 wt.% LN displays stronger piezocontrast as compared to pure KNN implying an evidence of a pronounced piezoelectric coefficient.     

Phase transitions and dielectric properties of (1 − x)KNbO3 − xK0.5Bi0.5TiO3 ceramics synthesized by a stirred hydrothermal process

Dielectric ceramic materials (1 − x) KNbO₃ − xK_0.5Bi_0.5TiO₃ (0 ≤ x ≤ 0.3) have been successfully synthesized via a stirred (dynamic) hydrothermal method. The microstructure, relative density and dielectric properties were studied as a function of KBT doping. The structure of the solid solutions changed from orthorhombic (x = 0; 0.05) to tetragonal (x = 0.1; x = 0.3) at room temperature. The morphotropic phase limit was obtained at x = 0.075 where we have noted the coexistence of the orthorhombic and tetragonal structures. The mean value of the measured dielectric permittivity ε_r was 700 and dielectric loss tanδ was about 0.06 at room temperature. The dielectric properties of the studied ceramics, from 80 to 450 K, depend not only on their microstructure but also on their relative density. A relaxation behavior was observed for the tanδ curves at temperature below 150 K. The activation energy (E_a) of this phenomenon increases from 0.15 to 0.34 eV with the increase of KBT amount. The conductivity σ_ac remains constant at about 10⁻⁶ S m⁻¹.     

Improving La0.6Sr0.4Co0.2Fe0.8O3 − δ cathode performance by infiltration of a Sm0.5Sr0.5CoO3 − δ coating

La_xSr_1 ? xCo_yFe_1 ? yO_3 ? δ (LSCF) represents one of the state-of-the-art cathode materials for solid oxide fuel cells (SOFCs) due primarily to its high ionic and electronic conductivity. In this study, a one-step infiltration process has been developed to deposit, on the surface of a porous LSCF cathode, a thin film (50–100 nm) of Sm_0.5Sr_0.5CoO_3 ? δ (SSC), which is catalytically more active for oxygen reduction. Electrochemical impedance spectroscopy reveals that the SSC coating has dramatically reduced the polarization resistance of the cathode, achieving area-specific resistances of 0.036 Ω cm² and 0.688 Ω cm² at 750 °C and 550 °C, respectively. It has also maintained the stability of LSCF cathodes. In particular, the peak power densities are increased by ~ 22% upon the infiltration of SSC onto the porous LSCF cathodes of our best performing cells. These results demonstrate that a conductive backbone (e.g., LSCF) coated with a catalytic film (e.g., SSC) is an attractive approach to achieving an active and stable SOFC cathode for low-temperature solid oxide fuel cells.     

Characterization of doped La0.7A0.3Cr0.5Mn0.5O3 − δ (A = Ca,Sr, Ba) electrodes for solid oxide fuel cells

Doped lanthanum manganese chromite based perovskite, La_0.7A_0.3Cr_0.5Mn_0.5O_3 ? δ (LACM, A = Ca, Sr, Ba), on yttria-stabilized zirconia (YSZ) electrolyte is investigated as potential electrode materials for solid oxide fuel cells (SOFCs). The electrical conductivity and electrochemical activity of LACM depend on the A-site dopant. The best electrochemical activity is obtained on the La_0.7Ca_0.3Cr_0.5Mn_0.5O_3 ? δ/YSZ (LCCM/YSZ) composite electrodes. The conductivity of LCCM is 29.9 S cm^? 1 at 800 °C in air, and the electrode polarization resistance (R_E) of the LCCM/YSZ composite cathode for the O₂ reduction reaction is 0.5 Ω cm² at 900 °C. The effect of Gd-doped ceria (GDC) impregnation on the LCCM cathode polarization resistances is also studied. GDC impregnation significantly enhances the electrochemical activity of the LCCM cathode. In the case of the 6.02 mg cm^? 2 GDC-impregnated LCCM cathode, R_E is 0.4 Ω cm² at 800 °C, ~ 60 times smaller than 24.4 Ω cm² measured on a LCCM cathode without the GDC impregnation. Finally the electrochemical activities of the doped lanthanum manganese chromites for the H₂ oxidation reaction are also investigated.     

Structural and electrochemical properties of LiNi0.5Mn0.5 − xAlxO2 (x = 0, 0.02, 0.05, 0.08, and 0.1) cathode materials for lithium-ion batteries

Layered LiNi_0.5Mn_0.5 ? xAl_xO₂ (x = 0, 0.02, 0.05, 0.08, and 0.1) series cathode materials for lithium-ion batteries were synthesized by a combination technique of co-precipitation and solid-state reaction, and the structural, morphological, and electrochemical properties were examined by XRD, FT-IR, XPS, SEM, CV, EIS, and charge–discharge tests. It is proven that the aliovalent substitution of Al for Mn promoted the formation of LiNi_0.5Mn_0.5 ? xAl_xO₂ structures and induced an increase in the average oxidation number of Ni, thereby leading to the shrinkage of the lattice volume. Among the LiNi_0.5Mn_0.5 ? xAl_xO₂ materials, the material with x = 0.05 shows the best cyclability and rate ability, with discharge capacities of 219, 169, 155, and 129 mAh g^? 1 at 10, 100, 200, and 400 mA g^? 1 current density respectively. Cycled under 40 mA g^? 1 in 2.8–4.6 V, LiNi_{0. 5}Mn_0.45Al_0.05O₂ shows the highest discharge capacity of about 199 mAh g^? 1 for the first cycle, and 179 mAh g^? 1 after 40 cycles, with a capacity retention of 90%. EIS analyses of the electrode materials at pristine state and state after first charge to 4.6 V indicate that the observed higher current rate capability of LiNi_{0. 5}Mn_0.45Al_0.05O₂ can be understood due to the better charge transfer kinetics.     

Intercomparison of Fluctuation Induced Conductivity of Cu0.5Tl0.5Ba2Can−1CunO2n+4−y (n = 2, 3, 4) superconductor thin films

An intercomparison of Fluctuation Induced Conductivity (FIC) of Cu_0.5Tl_0.5Ba₂Ca_n?1Cu_nO_2n+4?y (n = 2, 3, 4) [CuTl-12(n ? 1)n] superconductor thin films is given. We tried to find any correlation between the critical temperature and the parameters extracted from the excess conductivity data i.e. cross-over temperature, pseudogap temperature and fluctuation amplitudes. We found that the critical temperature seems to depend on the fluctuation amplitude; greater the fluctuation amplitude higher is the critical temperature.     

Electronic structure of CuClxBr1 − x,CuClxI1 − xand CuBrxI1 − xalloys

In this work, the electronic structure and disorder effects in copper halides alloys are studied by means of the full potential linearized augmented plane wave (FLAPW) method. The calculated bowing parameter shows that the main contribution is due to the relaxation effects, though the charge transfer remains relatively significant, while the volume deformation contribution is negligible. The total bowing is found to be small in the three studied alloys. Results agree well with experimental and available theoretical works.     

SrTiO3(100) − √5 × √5 − R26.6 surface observed by high-resolution scanning tunneling microscopy

SrTiO₃(100) – (√5 × √5) – R26.6 surfaces were studied by means of high-resolution scanning tunneling microscopy (STM) under ultrahigh vacuum conditions. By varying the bias voltage in the occupied state, it was possible to observe the arrangement of titanium and oxygen atoms in the unit cells of a (√5 × √5) surface superstructure, which revealed that the TiO₂ layer is the terminating plane of the (√5 × √5) surface. In the STM images, peculiar protrusions were seen at the oxygen fourfold hollow site responsible for √5 × √5 periodicity. The protrusions are asymmetrical in contrast, which would be an important consideration in proposing accurate structural models for (√5 × √5) surface superstructures.     

Oxygen nonstoichiometry and defect equilibrium in La2 − xSrxNiO4 + δ

Nonstoichiometric variation of oxygen content in La_2 ? xSr_xNiO_4 + δ (x = 0, 0.1, 0.2, 0.3, 0.4) and decomposition P(O₂) were determined by means of high temperature gravimetry and coulometric titration. The measurements were carried out in the temperature range between 873 and 1173 K and the P(O₂) range between 10^? 20 and 1 bar. La_2 ? xSr_xNiO_4 + δ showed the oxygen excess and the oxygen deficient compositions depending on P(O₂), temperature, and the Sr content. The value of partial molar enthalpy of oxygen approaches zero as δ increases in the oxygen excess region, which indicate that the interstitial oxygen formation reaction is suppressed as δ increase. The relationship between δ and logP(O₂) were analyzed by two types of defect equilibrium models. One is a localized electron model, and the other is a delocalized electron model. Both models can well explain the oxygen nonstoichiometry of La_2 ? xSr_xNiO_4 + δ with a regular solution approximation.     

Modification of B-site doping of perovskite LaxSr1 − xFe1 − y−zCoyCrzO3 − δ oxide by Mg2+ ion

Co-doping B-site of perovskite oxide La_xSr_1 ? xCo_yFe_1 ? yO_3 ? δ (LSCFO) with Cr⁶⁺ and Mg²⁺ ions has been attempted in this research for revamping chemical stability and oxygen ionic conductivity of this mixed conducting oxide. It is known that partial substitution for B-site cations of LSCFO by Cr gives rise to a significant improvement on chemical and thermal stability of the perovskite oxide. On the basis of this doped structure, introduction of an immaterial dose of Mg²⁺ ion into its B-site results in a microstructure consisting of smaller grains with higher density than its precursor. Furthermore, the resulting perovskite oxide La_0.19Sr_0.8Fe_0.69Co_0.1Cr_0.2 Mg_0.01O_3 ? δ (LSFCCMO) displays higher O^2? conductivity than the solely Cr-doped LSCFO besides the improved chemical stability against reduction in 5% CH₄/He stream at 850 °C. A detailed examination of the oxidation states of B-site transition metal ions by XPS has also been conducted as a part of structural characterizations of LSFCCMO. The assessment of relative O^2? conductivity shows that the grain boundary area plays a more important role than the bulk phase in facilitating ion transport, but with comparable boundary areas the higher densification level is favorable.     

Synthesis and electrical properties of nanocrystalline Ca1 − xEuxMnO3 ± δ (0.1 ≤ x ≤ 0.4) powders prepared at low temperature using citrate gel method

Nanopowders of Ca_1 − xEu_xMnO₃ (0.1 ≤ x ≤ 0.4) manganites were synthesized as a single phase using the auto gel-combustion method. The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation or contamination. The Ca_1 − xEu_xMnO₃ system has been synthesized at 800 °C during 18 h, against the conventional method of mixing oxides used to obtain these materials at higher temperatures of synthesis. The formation reaction was monitored by X-ray diffraction (XRD) analysis and an infrared absorption technique (FTIR). The polycrystalline powders are characterised by nanometric particle size, ∼ 48 nm as determined from X-ray line broadening analysis using the Scherrer equation. Morphological analysis of the powders, using the scanning electron microscope (SEM), revealed that all phases are homogeneous and the europium-substituted samples exhibit a significant decrease in the grain size when compared with the undoped samples. The structure refinement by using the Rietveld method indicates that the partial calcium substitution by europium (for x ≥ 0.3) modifies the orthorhombic structure of the CaMnO₃ perovskite towards a monoclinic phase. All manganites show two active IR vibrational modes around 400 and 600 cm^− 1. The high temperature dependence of electrical resistivity (between 25 and 600 °C) allows us to conclude that all the samples exhibit a semiconductor behaviour and the europium causes a decrease in the electrical resistivity by more than one order of magnitude. The results can be well attributed to the Mn⁴⁺/Mn³⁺ ratio.     

Radiation stability of M1 − xPrxF2 + x (M = Ca,Sr, Ba) crystals

The radiation stability of the mixed crystals M_1 ? xR_xF_2 + x (M = Ca, Sr, Ba) depends on types of the alkaline-earth and rare-earth ions. Different to Eu- and Ce-containing systems, M_1 ? xPr_xF_2 + x solid solutions have a low radiation resistance, which may be associated with hole trapping on praseodymium ion according to the reaction Pr³⁺ → Pr⁴⁺ which is typical for praseodymium. The coloration efficiency of M_1 ? xPr_xF_2 + x crystals grows in the row Ca → Sr → Ba, which is explained satisfactorily within the model of rare-earth clusters, the structure of which is determined by the ratio of the base alkaline-earth cation to the praseodymium ion radii.     

Performance evaluation of 64 × 10 Gbps and 96 × 10 Gbps DWDM system with hybrid optical amplifier for different modulation formats

In this paper, we investigated the performance of multi terabits DWDM system consisting of hybrid optical amplifier RAMAN-EDFA for different data format such as non-return to zero (NRZ), return to zero (RZ) and differential phase shift keying (DPSK). We find that in 64 × 10 and 96 × 10 Gbps, RZ is more adversely affected by nonlinearities, where as NRZ and DPSK is more affected by dispersion. We further show that RZ provide good quality factor (13.88 dB and 15.93 dB for 64 and 96 channels), less eye closure (2.609 dB and 3.191 dB for 64 and 96 channels) and acceptable bit error rate (3.89 × 10⁸ and 1.24 × 10⁹ for 64 and 96 channels) at the respective distance as compare to other existing modulation format. We further investigated the maximum single span distance covered by using existing data formats.     

Structure evolution and microwave dielectric response of (Ca0.5+xSr0.5−x)[(Al0.5Nb0.5)0.5Ti0.5]O3 solid solutions

The phase assemblage, crystal structure evolution and microwave dielectric response of (Ca_0.5+xSr_0.5−x)[(Al_0.5Nb_0.5)_0.5Ti_0.5]O₃ ceramics (abbreviated as CSANT hereafter) are investigated. Single perovskite solid solution is formed in the CSANT ceramics in Sr-rich composition range of x < −0.05, however, Ca₄Ti₃O₁₀-type layered perovskite phase begins to segregate after x = −0.05. The CSANT perovskites crystallized in Fm3m cubic symmetry in the composition range of x ≤ −0.2, however, as the Ca²⁺ content in A-site increased, the oxygen octahedral began to be anti-phase tilted at x = −0.1 and the crystal structure transited to P2₁/n pseudo-orthorhombic space group thereafter. The microwave dielectric response of the CSANT ceramics is elaborately discussed in terms of their crystallographic structure and chemical composition. When sintered at 1500 °C for 4 h, a dielectric constant ɛ_r of 52.5, a Qf product of 28000 GHz and a τ_f of +25.4 ppm/°C microwave dielectric ceramic can be obtained in the CSANT ceramics at x = 0.3.     

Effect of Eu dopant concentration in SrCe1 − xEuxO3 − δ on ambipolar conductivity

The europium dopant concentration in strontium cerate was studied to achieve maximum hydrogen permeation. In order to determine high ambipolar conductivity, total conductivity and open circuit potential measurements were performed. Among the three different compositions of Eu-doped SrCe_1 ? xEu_xO_3 ? δ (x = 0.1, 0.15 and 0.2) studied, SrCe_0.9Eu_0.1O_3 ? δ showed highest total conductivity between 600 °C and 900 °C. However, transference number measurements showed increasing electronic conductivity with increasing dopant concentration and a stronger temperature dependence for electronic conduction. Therefore, the highest ambipolar conductivity was obtained over the compositional range from SrCe_0.85Eu_0.15O_3 ? δ to SrCe_0.8Eu_0.2O_3 ? δ depending on temperature. Finally, the hydrogen permeation flux was calculated based on the ambipolar conductivity and compared with experimental results.     

A thermoluminescence study of mineral silicates extracted from herbs in the dose range 0.5–5 Gy

The presence of silicates in many personal objects suggests their potential use at low dose as fortuitous dosimeter in an accidental radiological exposure, when conventional dosimetry is not available. The goal of the present work is the dosimetric characterization of mineral silicates extracted from the plant Hibiscus Sabdariffa L, known as Jamaica flower, in the dose range 0.5–5 Gy. By studying the radiation-induced signal in time, the temperature integration region between 210 °C and 250 °C was found to be the most stable and also reduced the effects of thermal fading in the dose reconstruction process; the dose response curve was linear between 0.5 Gy and 5 Gy. By checking the change in sensitivity after repeated exposures to ionizing radiations and to high temperature heating, no variation in the glow curve shape or peak intensities were detected. To eliminate a pre-existing background signal, all the characterization measurements were performed with aliquots “annealed” by a preliminary readout of the TL.     

Thermal,Raman and dielectric study of 0.5K0.5Bi0.5TiO3–0.5PbTiO3 ceramics

The 0.5K_0.5Bi_0.5TiO₃–0.5PbTiO₃ ceramics were prepared by following a standard solid-state method. The Raman, thermal and dielectric properties of these ceramics were investigated. The X-ray measurements showed that samples have single perovskite-type structure with tetragonal symmetry. Dielectric study revealed that the dielectric behaviour of the investigated ceramics is rather of normal ferroelectrics with large thermal hysteresis. The transition temperature observed by means of differential scanning calorimetry measurements is in good agreement with that obtained from dielectric study.