Electrochemical properties of core-shell TiC-TiO2 nanoparticle films immobilized at ITO electrode surfaces

Titanium carbide (TiC) nanoparticles are readily deposited onto tin-doped indium oxide (ITO) electrodes in the form of thin porous films. The nanoparticle deposits are electrically highly conducting and electrochemically active. In aqueous media (at pH 7) and at applied potentials positive of 0.3 V vs. SCE partial anodic surface oxidation and formation (at least in part) of novel core-shell TiC-TiO2 nanoparticles is observed. Significant thermal oxidation of TiC nanoparticles by heating in air occurs at a temperature of 250 degrees C and leads first to core-shell TiC-TiO2 nanoparticles, next at ca. 350 degrees C to TiO2 (anatase), and finally at temperatures higher than 750 degrees C to TiO2 (rutile). Electrochemically and thermally partially oxidized TiC nanoparticles still remain very active and for some redox systems electrocatalytically active. Scanning and transmission electron microscopy (SEM and TEM), temperature dependent XRD, quartz crystal microbalance, and voltammetric measurements are reported. The electrocatalytic properties of the core-shell TiC-TiO2 nanoparticulate films are surveyed for the oxidation of hydroquinone, ascorbic acid, and dopamine in aqueous buffer media. In TiC-TiO2 core-shell nanoparticle films TiO2 surface reactivity can be combined with TiC conductivity.     

Geometric and electronic structure of lanthanide orthophosphate nanoparticles determined with X-rays

The evolution of the geometric and electronic structures within the entire series of lanthanide orthophosphate nanoparticles ( approximately 2- approximately 5 nm) has been determined experimentally with X-ray diffraction and near edge X-ray absorption fine structure spectroscopy. In particular, the interplay between electronic structure, crystal morphology, and crystal phase has been systematically studied. A missing local order in the crystal structure accompanied by multiple ion sites in the nanoparticles was revealed to be due to the small crystal size and large surface contribution. All lanthanide ions were found to be in "3+" configuration and accommodated in three different crystallization states: the larger lanthanide ions (La, Ce, Pr, Nd, Sm) in the monoclinic phase, the smaller ones (Er, Tm, Yb, Lu) in the tetragonal phase, and the intermediate lanthanide ions (Eu, Gd, Tb, Dy, Ho) in a "mixed phase" between monoclinic and tetragonal phases.     

Composition-dependent sintering behaviour of chemically synthesised CuNi nanoparticles and their application in aerosol printing for preparation of conductive microstructures

Copper, nickel and copper–nickel nanoparticles were prepared by solution combustion method for use in direct write printing. Structural (X-ray diffraction) and morphological (transmission electron microscope) investigations showed that pure metal (Cu and Ni) and CuNi alloy particles with face-centred cubic crystal structure were formed. Atomic absorption spectrometer studies confirmed that the nanoparticle compositions corresponded to the initial Cu/Ni molar ratios selected for synthesis. Particle size and morphology were significantly influenced by composition, with high Cu content coinciding with small, spherical particles as opposed to larger, irregular shapes observed at high Ni concentrations. X-ray photoelectron spectroscopy measurements revealed that after the reduction process the surface of the alloy nanoparticles was partially oxidised in air and the amount of metallic surface species decreased, while the concentration of oxidic surface species and hydroxides increased with increasing Cu concentration (i.e. decreasing particle size). Dispersions of CuNi nanoparticles have been deposited by use of AerosolJet? and sintered under reducing atmosphere at 300–800?°C in order to prepare conductive structures. Resistivity measurements and microscopical studies (SEM-FIB) of printed and sintered CuNi structures showed that the sintering properties of nanoparticles were dependent on their chemical composition.     

棒状CeO_2负载Pt催化剂的合成及其电化学性能研究

通过水热法合成棒状纳米Ce O2(Ce O2-R),并将Pt纳米颗粒负载于Ce O2表面,制得甲醇燃料电池的阳极催化剂Pt/Ce O2-R.通过结构与形貌表征,结果表明,Pt/Ce O2-R中Ce O2的暴露晶面为(111)和(002)晶面,改变了Pt周围的电子结构,进而降低了Pt-COads的键能,释放出更多的活性位.另外,Pt纳米颗粒在Ce O2-R表面分散更均匀.利用电化学工作站测试阳极催化剂Pt/Ce O2-R在酸性溶液中的电化学性能,证明Pt/Ce O2-R催化剂的甲醇电氧化性能与抗CO毒害能力较颗粒状Ce O2负载Pt催化剂(Pt/Ce O2-P)都有很大的提高,证明Ce O2-R作为Pt纳米颗粒的载体用于直接甲醇燃料电池的阳极反应具有发展潜力.     

A comparative density functional study of the low pressure phases of solid ZnX, CdX, and HgX: trends and relativistic effects

A comprehensive density functional study of the group 12 chalcogenides has been carried out to study the impact of relativistic effects on the solid-state and electronic structure of the mercury chalcogenides in order to explain their unique behavior compared to the lighter group 12 congeners. For this, we present scalar-relativistic and nonrelativistic density functional calculations for several crystal structures commonly occurring in ZnX, CdX, and HgX (X = S, Se, and Te). The cohesive energies and other ground-state properties (at the zero-temperature limit) are obtained to identify the low-pressure phases and to discuss relativistic effects. Relativistic crucially influences the crystal structure in HgS, an effect less pronounced in the heavier chalcogenides HgSe and HgTe. However, for HgSe and HgTe we find that relativistic effects have a major impact on the electronic structure, where the change upon neglect of relativity goes as far as to the restoration of semiconducting properties.     

Preparation of Luminescent Polyelectrolyte/Cu-Doped ZnSe Nanoparticle Multilayer Composite Films

ZnSe and Cu-doped ZnSe nanoparticle aqueous suspensions were prepared in the presence of mercaptopropionic acid (MPA). Cu-doped ZnSe nanoparticles exhibited a strong blue emission that was strongly dependent upon the Cu dopant level and the chemical surface passivation produced by zinc-mercaptopropionic acid complexes. These Cu-doped ZnSe nanoparticles were further assembled into ultrathin polymer-supported films using electrostatic interactions and the layer-by-layer assembly method. UV-visible spectroscopy and X-ray photoelectron spectroscopy (XPS) provided evidence for the presence and optical activity of Cu-doped ZnSe nanoparticles within the polymer ultrathin films. Moreover, XPS data supported the presence of zinc mercaptopropionic acid complexes on nanoparticle surfaces and the presence of Cu(+) ions with high luminescent activity in the doped nanoparticles. Copyright 2001 Academic Press.     

Chitosan‐Functionalized Carbon Nanotubes as Support for the High Dispersion of PtRu Nanoparticles and their Electrocatalytic Oxidation of Methanol

Carbon nanotubes (CNTs) were non‐covalently functionalized with chitosan (Chit) and then employed as the support for PtRu nanoparticles. The functionalization was carried out at room temperature without the use of corrosive acids, thereby preserving the integrity and the electronic conductivity of the CNTs. Transmission electron microscopy reveals that PtRu nanoparticles were highly dispersed on the surface of Chit‐functionalized CNTs (CNT‐Chit) with small particle‐size. Cyclic voltammetry studies indicated that the PtRu nanoparticle/CNT‐Chit nanohybrids have a higher electrochemical surface area, electrocatalytic performance, and stability towards methanol oxidation compared to PtRu nanoparticles supported on the pristine CNTs.     

Effect of copper nanoparticle aggregation on the thermal conductivity of nanofluids

The thermal conductivity of water and glycerol is investigated via the transient hot wire method by adding small amounts of copper nanoparticles to solutions. At a 0.2% copper nanoparticle concentration, the thermal conductivity coefficient rises to 25% for the Cu + glycerol system, and to 35% for Cu + water system. A mechanism and mathematical model for describing the nanoparticle aggregation effect on the thermal properties of nanofluids are proposed, based on an analysis of the accumulated experimental data. It is shown that the enhancement of nanofluid thermal conductivity at low nanoparticle concentrations is directly proportional to their volume fraction and thermal conductivity coefficient, and (in accordance with the literature data) is inversely proportional to the radius and the aggregation ratio. The proposed model describes the existing experimental data quite well. The results from this work can be applied to the rapid cooling of electronic components, in the power engineering for ensuring the rapid and effective transfer of thermal energy in a nuclear reactor, and in the oil industry for thermal stimulation.     

Synthesis of hafnium oxide-gold core-shell nanoparticles

Developing cheap composite nanoparticle systems that combines a high dielectric constant with good conductivity is important for the future of the electronic industry. In this study, two different sizes, 7.3 ± 2.2 and 5.6 ± 1.9 nm, of HfO(2)@Au core-shell nanoparticles are prepared by using a high-temperature reduction method. The core-shell nanoparticles are characterized by powder X-ray diffraction, high-resolution transmission electron microscopy (HRTEM), energy dispersive X-ray analysis (EDX), and UV-visible absorption spectroscopy. HfO(2) exhibits no absorption in the visible region, but the HfO(2)@Au core-shell nanoparticles show a plasmon absorption band at 555 nm that is 25 nm red-shifted as compared to pure gold nanoparticles. According to transmission electron microscopy and energy dispersive X-ray analysis, the HfO(2) particles are coated with approximately three atomic layers of gold.     

Formation of silver nanoparticles in deoxyribonucleic acid-poly(o-methoxyaniline) hybrid: a novel nano-biocomposite

A novel nano-biocomposite of silver and poly(o-methoxy aniline) (POMA)/DNA hybrid has been prepared by adding DNA solution to an aqueous solution of POMA (emeraldine base, EB) and AgNO(3) mixture. The mixture was aged for 10 days and was freeze-dried to form the hybrid nanocomposite (weight fraction of DNA = 0.75). FESEM pictures show a fibrillar network morphology of the biomolecular hybrid with silver nanoparticles on its surface. The TEM picture also corroborates silver nanoparticle formation in the biomolecular hybrid, and the denser population of nanoparticles in the TEM micrograph as compared to that in the SEM micrograph indicates that the nanoparticles are present inside the fibrils in greater proportion. The dc conductivity value of the hybrid indicates that POMA (EB) is doped by silver ion and the doped POMA form complexes with DNA through electrostatic interaction of the radical cation of POMA (emeraldine salt form, ES) and the DNA anion. During the doping process and Ag nanoparticle formation, a fluctuation of the pi band to polaron band transition peak occurs together with a complementary fluctuation of the polaron band to pi* band transition peak. After 53 h of aging, the former shows a slow but continuous red shift with aging time. This has been attributed to the slow uncoiling of POMA on the DNA surface. The conformation and crystal structure of DNA remain intact during the nano-biocomposite formation. The dc conductivity value of the nano-biocomposite is almost the same as that of the pure POMA-DNA hybrid at the same composition, but the I-V characteristic curve of the nano-biocomposite is somewhat different showing an insulating region on low applied voltage. At higher applied voltage, it shows a semiconducting property characterizing the large band gap semiconducting behavior of the nano-biocomposite.     

Sensory properties of oxide films with high concentrations of conduction electrons

The dependence of a sensor’s response to hydrogen on the temperature and hydrogen pressure in an indium oxide nanostructured film is measured. A theory of sensor’s response to reducing gases in nanostructured semiconducting oxides with high concentrations of electrons in the conduction band is developed (using the example of In₂O₃). It is shown that the capture of conduction electrons by adsorbed oxygen redistributes the electrons in nanoparticles and reduces the surface electron density and the conductivity of a system; the conductivity is proportional to the electron density in nanoparticle contacts, i.e., to the surface electron density. It is found that atomic oxygen ions react with reducing gases (H₂, CO) during adsorption of the latter: electrons are released and enter the volumes of nanoparticles; the conductivity of the system grows, creating the sensory effect. Using a model developed earlier to describe the distribution of conduction electrons in a semiconductor nanoparticle, a kinetic scheme corresponding to the above scenario is built and corresponding equations are solved. As a result, a theoretical dependence of a sensor’s sensitivity to temperature is found that describes the experimental data well.

     

Tuning supported catalyst reactivity with dendrimer-templated Pt-Cu nanoparticles

The effects of particle composition on heterogeneous catalysis were studied using dendrimer-encapsulated nanoparticles (DENs) as precursors to supported Pt-Cu catalysts. Bimetallic Pt-Cu DENs with varying Pt/Cu ratios were prepared in an anaerobic aqueous solution and deposited onto a high-purity commercial alumina support. The dendrimer template was then thermally removed to yield supported nanoparticle catalysts, which were studied with toluene hydrogenation and CO oxidation catalysis as well as infrared spectroscopy of adsorbed CO. Incorporating Cu into Pt nanoparticles had opposite effects on the two test reactions. Cu acted as a mild promoter for CO oxidation catalysis, and the promoting effect was independent of the amount of Cu present. Conversely, Cu acted as a strong poison for toluene hydrogenation catalysis, and the normalized rate tracked inversely with Cu content. Infrared spectroscopy of the supported nanoparticles indicated that electronic effects (electron donation from Cu to Pt) were minimal for these materials. Consequently, the catalysis results are interpreted in terms of potential structural differences as a function of Cu incorporation and reaction conditions.     

Optical and electrical properties of copper alumina nanoparticles reinforced chlorinated polyethylene composites for optoelectronic devices

The incorporation of transition metal oxide fillers into the polymer matrix through solution mixing polymerization imparts enhanced electrical and thermal properties. The present work focused on the optical properties, crystallinity, thermal stability, temperature-dependent conductivity, dielectric constant and modulus of chlorinated polyethylene/copper alumina (CPE/Cu–Al₂O₃) nanocomposites. Optical absorption measured using an ultraviolet–visible (UV–visible) spectrometer shows enhanced intensity and a blue shift for CPE/Cu–Al₂O₃ nanocomposites. The bandgap energy of CPE/Cu–Al₂O₃ nanocomposites was lower than pure CPE and minimum bandgap energy was recorded for a 7 wt% composites. The X-ray diffraction demonstrates that Cu–Al₂O₃ nanoparticles were uniformly introduced into the CPE matrix. Thermogravimetric analysis (TGA) manifests improved thermal stability of nanocomposites. Dielectric properties decrease with frequency, whereas AC conductivity increases with frequency, and both AC conductivity and dielectric properties increase with temperature. The maximum AC conductivity and dielectric constant were obtained for 7 wt % nanofiller loaded sample. For all systems, the activation energy for electrical conductivity decreases with rising temperatures. The experimental dielectric constant values of CPE nanocomposites were correlated with different theoretical models. The Bruggeman model was in good agreement with the experimental permittivity. The impedance experiments showed a decreasing trend with temperature, indicating the semiconducting nature of prepared nanocomposites.     

Size effects in electronic and catalytic properties of unsupported palladium nanoparticles in electrooxidation of formic acid

We report a combined X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), and chronoamperometry (CA) study of formic acid electrooxidation on unsupported palladium nanoparticle catalysts in the particle size range from 9 to 40 nm. The CV and CA measurements show that the most active catalyst is made of the smallest (9 and 11 nm) Pd nanoparticles. Besides the high reactivity, XPS data show that such nanoparticles display the highest core-level binding energy (BE) shift and the highest valence band (VB) center downshift with respect to the Fermi level. We believe therefore that we found a correlation between formic acid oxidation current and BE and VB center shifts, which, in turn, can directly be related to the electronic structure of palladium nanoparticles of different particle sizes. Clearly, such a trend using unsupported catalysts has never been reported. According to the density functional theory of heterogeneous catalysis, and mechanistic considerations, the observed shifts are caused by a weakening of the bond strength of the COOH intermediate adsorption on the catalyst surface. This, in turn, results in the increase in the formic acid oxidation rate to CO2 (and in the associated oxidation current). Overall, our measurements demonstrate the particle size effect on the electronic properties of palladium that yields different catalytic activity in the HCOOH oxidation reaction. Our work highlights the significance of the core-level binding energy and center of the d-band shifts in electrocatalysis and underlines the value of the theory that connects the center of the d-band shifts to catalytic reactivity.     

Bimetallic Cu–Pt/nanoporous carbon composite as an efficient catalyst for methanol oxidation

A novel bimetallic Cu–Pt nanoparticle supported onto Cu/indirectly carbonized nanoporous carbon composite (Cu–Pt/ICNPCC) was prepared through a two-step process: first, carbonization of furfuryl alcohol-infiltrated MOF-199 [metal–organic framework Cu₃(BTC)₂ (BTC?=?1,3,5-benzene tricarboxylate)], without removing the Cu metal with HF aqueous solution; second, the partial galvanic replacement reaction (GRR) of Cu nanoparticles by Pt^IV upon immersion in a platinum(IV) chloride solution. The synthesized materials characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy (EDS), and electrochemical methods. The EDS result revealed that part of Cu nanoparticles have been substituted by Pt nanoparticles after GRR. The methanol oxidation at the surface of Cu–Pt/ICNPCC was investigated by cyclic voltammetry method in 0.5 M H₂SO₄ and indicated good electro-catalytic activity towards methanol oxidation (E_p?=?0.85 V vs. NHE and j_f?=?1.00 mA cm^?2). It is suggested that this improvement is attributed to the effect of proper Cu/ICNPCC for fine dispersion, efficient adhesion, and prevention of Pt coalescing.     

On the ordering in new low gap semiconductors: PtSnS, PtSnSe, PtSnTe. Experimental and DFT studies

The crystallographic and electronic structures of PtSnS, PtSnSe and PtSnTe were investigated by X-ray structure analysis and density functional theory (DFT) calculations. Conductivity measurements and diffraction patterns show semiconducting ordered pyrite type related compounds containing SnX (X=S, Se, Te) entities. A scheme is presented to model ordered variants according to the relative orientation of the XY dumbbells. It represents the ullmannite, the cobaltite and a new rhombohedral structure type. The scheme allows for a systematic investigation of ordering preferences from first principles. According to the total electronic energy PtSnTe and PtSnSe prefer the cobaltite, PtSnS the rhombohedral structure type. The structural and electronic properties agree with experimental results. The three compounds are predicted to be narrow gap indirect semiconductors from conductivity measurements and band structure calculations.     

Stabilization by a divalent transition metal in lead indium quaternary selenide, Fe(0.47)Pb(8.04)In(17.37)Se(34), and specific indium coordination

Single crystals of the first M-Pb-In-Se quaternary selenide, Fe(0.47)Pb(8.04)In(17.37)Se34, with the structure stabilized by a divalent transition metal (M = Fe), have been grown by a solid-state reaction. The Fe(II) ions partially occupy at the In sites with various Fe/In ratios. Thus, a new crystal structure is evolved by partially occupied minor Fe atoms at In sites. A part of the In atoms shows remarkably distorted octahedral coordination. This compound shows relatively high conductivity (approximately 40 S/m at 300 K) with a narrow-band-gap-type semiconducting property (Ea = 0.078 eV).     

Synthesis and structural characterization of Se-modified carbon-supported Ru nanoparticles for the oxygen reduction reaction

This work is part of a continued research aimed at the understanding of the promoting role of Se in the enhancement of the electrocatalytic activity of Ru in the oxygen reduction reaction. The objective of this paper is to systematically investigate the transformation of Ru nanoparticles upon their modification with the increasing amounts of Se. The Se-modified Ru/C samples with Se:Ru ratio from 0 to 1 were prepared by reacting carbon-supported Ru nanoparticles with SeO2 followed by reductive annealing and characterized using high-resolution transmission electron microscopy, energy-dispersive X-ray, X-ray diffraction analysis, X-ray photoelectron spectroscopy, and extended X-ray absorption fine structure. The results suggest that Se strongly interacts with Ru, resulting in the chemical bond between Ru and Se and formation of Ru selenide clusters whose core at low Se content can be described as Ru2Se2O0.5. At Se:Ru = 1, high-resolution electron microscopy shows evidence of formation of core-shell particles, comprising a hexagonally packed Ru core and a Ru selenide shell with lamellar morphology. Modification of Ru nanoparticles with Se enhances their electrocatalytic activity in the oxygen reduction reaction, which is explained by the role of Se in inhibiting surface oxidation.     

Charge separation and surface reconstruction: a Mn2+ doping study

Hydrothermal synthesis of Mn doped anatase (TiO2) nanoparticles using scrolled nanotubes of TiO2 and MnCl2 as the starting materials is described. Incorporation of Mn2+ ions on the substitutional sites was confirmed using X-ray absorption fine structure (FT-XAFS) while the oxidation state Mn(II) and coordination environment were determined using both electron paramagnetic resonance (EPR) and X-ray absorption near edge spectroscopy (XANES). Two different hyperfine couplings of 96 and 86 G were found using high-field (130 GHz) EPR reporting that Mn atoms occupy two distinct sites: one undercoordinated (reconstructed surface) and the other octahedral crystalline geometry (nanoparticle core), respectively. It was found that Mn atoms that occupy surface layers are weakly bound to the anatase lattice and can be easily leached using simple dialysis, while those incorporated in the nanoparticle core are bound more strongly and cannot be removed by dialysis. Light excitation EPR reveals that Mn ions incorporated in the surface layers participate in the charge separation, while those trapped deeply in the nanoparticle core do not show any photoactivity. Doping of the core of nanoparticles with Mn2+ ions, on the other hand, enables synthesis of optically transparent films having superparamagnetic behavior at room temperatures with a saturation magnetic moment of 1.23 microB per Mn atom.     

A modular nanoparticle-based system for reagentless small molecule biosensing

Metalloprotein tethered CdSe nanoparticles have been generated to provide selective and reagentless maltose biosensing. As opposed to cell or protein detection by semiconducting nanoparticle bioconjugates, a modular method for small-molecule detection using semiconducting nanoparticle bioconjugates has been difficult. Here we report a method for reagentless protein-based semiconducting nanoparticle biosensors. This method uses Ru(II) complex-CdSe nanoparticle interactions and the maltose-induced conformation changes of maltose binding protein to alter the CdSe nanoparticle fluorescence emission intensity. In this proof-of-principle system, the maltose-induced protein conformation changes alter the Ru(II) complex-CdSe nanoparticle interaction, which increases the CdSe emission intensity. Altered CdSe emission intensity effects are best described as electron transfer from the Ru(II) complex to the CdSe excited state forming the nonfluorescent CdSe anion. Four surface-cysteine, Ru(II) complex-attached maltose-binding proteins have been studied for maltose dependent alteration of CdSe emission intensities. With 3.0-3.5 nm diameter CdSe nanoparticles, all ruthenated maltose-binding proteins display similar maltose-dependent increases (1.4-fold) in CdSe emission intensity and maltose binding affinities (KA = 3 x 106 M-1). For these four systems, the only difference was the sample-to-sample variation in maltose-dependent responses. Thus, very few surface cysteine mutations need to be examined to find a successful biosensor, as opposed to analogous systems using organic fluorophores. This strategy generates a unimolecular, or reagentless, semiconducting nanoparticle biosensor for maltose, which could be applied to other proteins with ligand-dependent conformation changes.