A High-Gain, 28GHz, 200kW Gyroklystron Amplifier

A design study of a high efficiency/gain gyroklystron amplifier is performed to demonstrate amplified radiation power of 200kW operating at 28GHz. A key design feature of the present gyroklystron amplifier is that the amplifier is designed to be high gain so that it can be saturated by a low power solid state power amplifier. A non-linear, time-dependent, large signal numerical code is used to predict tube performance. Simulations predict that a stable amplifier radiation power of 214kW is produced with a saturated gain of 54dB, an electronic efficiency of 37%, and a frequency bandwidth of 0.3% from a five-cavity gyroklystron amplifier. The amplifier gain is found to be very sensitive to a beam velocity spread.     

倍频谐波回旋行波放大器的研究

 通过研究倍频谐波回旋行波放大器中电子束在调制区和漂移区中的群聚与在辐射区中的辐射,给出了器件各部分的最佳参数;同时在均匀波导管和引导场的情况下,运用低速率比的电子束获得了宽带输出。当电子束的电压为130kV、电流为20A、速率比为0.8以及纵向速度散度为1%时,模拟得到器件的饱和带宽至少可达到10%,峰值功率和增益分别为290k W和50dB,常数驱动带宽约9%。     

Preliminary Design of a Harmonic-doubling Gyrotron Traveling Wave Amplifier

This study proposes a Ka-band harmonic-doubling gyrotron traveling-wave amplifier (gyro- TWT), using distributed wall losses in the input stage and mode-selective interaction circuit in the output stage, to improve the stability of the amplification. Based on a large signal simulation code, a saturated peak power of 163 kW with an efficiency of 15.5%, a gain of 31.1 dB, and a 3 dB bandwidth of 0.9 GHz is predicted for the gyro-TWT driven by 70 kV, 15 A electron beam with a velocity ratio of 1.2 and velocity spread 5% at 33.2 GHz.     

High-gain wide-band gyrotron traveling wave amplifier with a helically corrugated waveguide

First bandwidth measurements of a novel gyrotron amplifier are presented. The coupling between the second harmonic cyclotron mode of a gyrating electron beam and the radiation field occurred in the region of near infinite phase velocity over a broad bandwidth by using a cylindrical waveguide with a helical corrugation on its internal surface. With a beam energy of 185 keV, the amplifier achieved a maximum output power of 1.1 MW, saturated gain of 37 dB, linear gain of 47 dB, saturated bandwidth of 8.4 to 10.4 GHz ( 21% relative bandwidth), and an efficiency of 29%, in good agreement with theory.     

Design of a 50 kW, wideband Ka-band slow wave cyclotron amplifier

A two-stage slow wave cyclotron amplifier is investigated to demonstrate a high power, stable, and broad Ka-band radiation source, operating at a low beam power (~60 kV, ~5 amps) and a low magnetic field (~7 kG). A linear theory predicts that the second harmonic gyro-BWO is competing in the amplifier and can be stabilized by inserting a sever in the interaction circuit. A slow-time-scale non-linear code, with a sever included, predicts a saturated gain of 24-28 dB, an efficiency of 15-17%, and an instantaneous bandwidth of 15-20% at a beam axial velocity spread of 2%. A broadband RF coupler, a mode converter, and a RF vacuum window are designed by the use of a 3D electromagnetic, finite element code. Measured RF characteristics are in good agreement with predictions     

Nonlinear Analysis of Coaxial Gyro-Travelling-Wave-Tube Amplifier

A set of nonlinear self-consistent equations in the electron guiding center coordinates is derived for the study of the behavior of the coaxial gyro-travelling-wave-tube (gyro-TWT) amplifier. It is found that the input signal grows faster and gets saturated earlier with the increasing of b/a (ratio of the inner to outer radius). Using an electron beam of 90kV, 10A and velocity ratio of 1.0 with 3% axial velocity spread, 275kW peak output power is obtained by calculation over the frequency range of 31.22–33.52GHz, the gain, efficiency and bandwidth are 47.4dB, 30.5% and 7.5%, respectively.     

Large-signal characteristics of a wide-band dielectric-loadedgyro-TWT amplifier

The bandwidth of a gyrotron traveling wave amplifier (gyro-TWT) has been significantly increased by partially filling the interaction waveguide with dielectric to reduce the circuit's dispersion. The proof-of-principle experiment was designed for X-band, and employs the fundamental mode of rectangular waveguide loaded with dielectric slabs along the narrow sidewalls. The amplifier yields a peak output power of 55 kW with 11% efficiency, 27 dB saturated gain, and an unprecedented untapered gyro-TWT constant-drive bandwidth of 11% and saturated bandwidth exceeding 14%. The single-stage amplifier is completely zero-drive stable. The 95-kV 5-A electron beam was produced by a single-anode magnetron injection gun with p_⊥/υ_z=0.6, as determined by the EGUN code, and Δυ_z/υ_z=4%, determined as the best fit to the gyro-TWT large-signal simulation data. Simulation studies predict that by lowering the velocity spread to Δυ _z/υ_z=2%, the amplifier performance will be further enhanced to a constant-drive bandwidth of 20% with 15% efficiency     

同轴回旋行波放大器的理论和数值研究

 给出了一组描述同轴回旋行波放大器中波束相互作用的非线性自洽方程组，对该放大器的运行特性进行了研究。得到：在小信号区，辐射场的增益随同轴波导的内外半径比b/a的增加而增加，达到饱和时的辐射功率仅略有下降；内外导体管壁上的功率损耗密度随b/a的增加而减小。采用电压为90kV，电流为10A，纵向速度零散度为3%，速率比为1的电子束，在34.26～36.78GHz的频率范围内，计算得到了峰值功率约230kW的微波输出，相应的增益和效率分别为46.6dB和25.5%，带宽为7%，内外导体管壁上功率的最大损耗分别为80和56W/cm²。     

回旋速调管放大器注-波互作用分析

 给出了自洽非线性大信号理论分析方法,在理论分析和高频计算的基础上,建立了回旋速调管放大器注-波互作用计算模型,对其进行数值计算。研究多种参量对放大器输出功率、增益、效率等的影响,通过优化得到了中心频率34 GHz的四腔回旋速调管放大器设计方案。粒子模拟表明：在工作电压65 kV,注电流8 A,电子注横向与纵向速度比为1.5时,输出功率230 kW,带宽230 MHz,电子效率45%,饱和增益33 dB。     

Theory and experiment of ultrahigh-gain gyrotron traveling waveamplifier

Physics and technology issues of importance to the high-gain gyrotron traveling wave amplifier (gyro-TWT) are investigated in theory and experiment. The gyro-TWT is known to be highly susceptible to spurious oscillations, especially in high gain operations. In the current study, oscillations of various origins are classified and characterized with detailed theoretical modeling. They are shown to be intricately connected to the interplay between the absolute/convective instabilities, circuit losses, and reflective feedback. Knowledge of these processes leads to the concept of an ultra high gain scheme which employs distributed wall losses for the suppression of spurious oscillations. A proof-of-principle Ka-band gyro-TWT experiment stable at zero drive has produced 93 kW saturated peak power at 26.5% efficiency and 70 dB gain, with a 3 dB saturated output power bandwidth of 3 GHz. The saturated gain is more than 30 dB beyond that previously achieved     

Stable high-power TE01 gyro-TWT amplifiers

The stability of high power gyro-TWT amplifiers operating in the low-loss TE₀₁ mode of cylindrical waveguide has been studied, Linear theory has been used to determine the threshold start-oscillation beam current for absolute instability in the operating mode and the critical section lengths for the dominant gyro-BWO interactions occurring at various cyclotron harmonics in other waveguide modes. The performance of the amplifier was evaluated with a nonlinear, self-consistent slow-timescale simulation code. Utilizing interaction sections whose lengths are less than the threshold start-oscillation length and are separated by attenuating severs for isolation, two stable three-section devices have been designed which are predicted to yield: (1) a peak output power of 230 kW at 35 GHz with an efficiency of 23%, a saturated gain of 46 dB and a constant-drive bandwidth of 6% for a 100 kV, 10 A electron beam with an α=ν_⊥ /ν_z =1.0 and an axial velocity spread Δν_z/ν_z=5% and (2) 105 kW at 94 GHz with 21% efficiency, 45 dB saturated gain and 5% constant-drive bandwidth for a similar 5 A electron beam. In addition, the design of the 0 dB input/output couplers and the MIG electron gun are given. Due to the low loss of the TE₀₁ mode, both of these amplifiers can be operated continuously     

Stability of a 95-GHz slotted third-harmonic gyro-TWT amplifier

A low-magnetic-field moderate-voltage gyrotron amplifier has been designed for stable high-performance operation at 95 GHz. A slotted interaction circuit is utilized to achieve strong amplification near the third cyclotron harmonic frequency. The start-oscillation conditions were determined by an analytical theory and confirmed by a multimode particle-in cell simulation code. The dominant threat to the amplifier's stability is from a third-harmonic peniotron backward-wave interaction. A slow-timescale particle-tracing simulation code predicts the three-section slotted third-harmonic gyro-TWT, which utilizes an 11.6-kG magnet and a 50-kV 3-A υ_⊥/υ_z=1.4 axis-encircling electron beam with an axial velocity spread of 6% will yield an output power of 30 kW with an efficiency of 20%, a saturated gain of 40 dB, and a constant-drive bandwidth of 2%     

Ka波段二次谐波回旋速调管放大器的输出特性

 根据谐波回旋速调管放大器的注-波互作用特点,对Ka波段二次谐波三腔回旋速调管放大器的输出腔进行了数值模拟和优化设计,获得了输出腔末端高频波绕射输出孔径和腔体绕射Q值的对应关系。通过PIC粒子模拟,分析了该放大器的频率响应特点等输出特性。结果表明,在35 GHz频率,磁场0.685 T,电子注电压70 kV,电流15 A,横纵速度比为1.45,输入功率1.6 kW时,放大器可以获得超过220 kW的峰值输出功率、约22%的效率和23 dB的增益,3 dB带宽可达到110 MHz。     

Kα波段TE01模基波回旋速调放大器的设计与实验

在回旋速调放大器自洽非线性大信号理论分析和数值计算的基础上,给出了一支Kα波段TE₀₁模4腔基波回旋速调放大器的设计方案,并完成了样管的研制.同时对样管进行了热测实验,得到了如下实验结果:注电压为70 kV,电流为10 A,输入功率为60 W,磁场强度1.31 T,中心频率34 GHz,峰值功率245 kW,平均功率大于3 kW,增益36.1 dB,效率 35%,3 dB带宽大于280 MHz. 关键词： 回旋速调放大器 注-波互作用 群聚腔 输入腔     

D波段功率放大器设计

基于0.13 m SiGe BiCMOS工艺, 研究和设计了一种D波段功率放大器芯片。该放大器芯片用了四个功率放大器单元和两个T型结网络构成。功率放大器单元采用了三级的cascode电路结构。低损耗的片上T型结网络既能起到片上功率合成/分配的功能, 又能对输入输出进行阻抗匹配。对电路结构进行了设计、流片验证和测试。采用微组装工艺将该芯片封装成为波导模块。小信号测试结果表明:该功放芯片工作频率为125~150 GHz, 最高增益在131 GHz为21 dB, 最低增益在150 GHz为17 dB, 通带内S22小于-7 dB, S11小于-10 dB。大信号测试结果表明:该功放模块在128~146 GHz带内输出功率都大于13 dBm, 在139 GHz时, 具有最高输出功率为13.6 dBm, 且1 dB压缩功率为12.9 dBm。     

Operation of a stable 200-kW second-harmonic gyro-TWT amplifier

The experimental results are reported for a stable second-harmonic gyrotron traveling wave amplifier, which generated a record-breaking 207-kW output power based on the principle that the weaker harmonic interactions are more stable to spontaneous oscillations than at the fundamental, and therefore, capable of generating higher output power. The high-power amplifier was kept completely (zero-drive) stable by employing a mode-selective interaction circuit and web-matched directional input and output couplers, and choosing an amplifier interaction length shorter than the start-oscillation length for gyrotron backward-wave oscillations. The single-stage Ku-band amplifier utilized an 80-kV 20-A υ_⊥/υ_∥=1.1 electron beam from a magnetron injection gun and yielded an efficiency of 12.9%, an output phase variation of 10°/kV, a saturated bandwidth of 2.1%, a large-signal gain of 16 dB, and a detuned small-signal gain of 38 dB     

Broadband operation of a Ka-band tapered gyro-traveling waveamplifier

A wideband low-voltage millimeter-wave gyro-traveling wave tube (gyro-TWT) amplifier operating in the TE₁₀ rectangular waveguide mode at the fundamental cyclotron frequency is under investigation, The device incorporates precise axial tapering of both the magnetic field and the interaction circuit for broadband operation. Experimental results of a wide (33%) instantaneous bandwidth with a small signal gain in excess of 20 dB and saturated efficiency of ~10% were achieved and shown to be in good agreement with the theory. Reflective instability due to multi-pass effects by mismatches was observed and characterized. Gain and efficiency have been limited by this reflective instability rather than by absolute instabilities which limit the performance of gyro-TWT's with uniform cross-section. The start-oscillation current in terms of the relevant experimental parameters such as the beam velocity ratio (α), magnetic field detuning and reflection coefficient has been measured and compared with theory. Measurements of the phase variation in terms of the RF frequency have shown that the phase varies ±30° from fitted linear phase line     

A gain-clamped-semiconductor-optical-amplifier combined with a distributed Raman-fiber-amplifier: a good candidate as an inline amplifier for WDM networks

A gain-clamped semiconductor optical amplifier (SOA) is used as an inline amplifier in combination with a distributed Raman fiber amplifier. The combined amplifier has 20 dB gain and a noise figure below 2.7 dB. The optical signal to noise ratios after five spans of 20 dB loss, equivalent to 5 × 80 km, are over 25.2 dB for eight-channel transmissions. In addition, the potentially compact amplifier shows negligible transients under dynamic add-drops.     

High-power SiC MESFET using a dual p-buffer layer for an S-band power amplifier

A silicon carbide (SiC) based metal semiconductor field effect transistor (MESFET) is fabricated by using a standard SiC MESFET structure with the application of a dual p-buffer layer and a multi-recessed gate to the process for an S-band power amplifier. The lower doped upper-buffer layer serves to maintain the channel current, while the higher doped lower-buffer layer is used to provide excellent electron confinement in the channel layer. A 20-mm gate periphery SiC MESFET biased at a drain voltage of 85 V demonstrates a pulsed wave saturated output power of 94 W, a linear gain of 11.7 dB, and a maximum power added efficiency of 24.3% at 3.4 GHz. These results are improved compared with those of the conventional single p-buffer MESFET fabricated in this work using the same process. A radio-frequency power output greater than 4.7 W/mm is achieved, showing the potential as a high-voltage operation device for high-power solid-state amplifier applications.     

用楔形柱面光纤微透镜耦合的1.3μm SOA组件

运用激光模式耦合理论分析了半导体光放大器(SOA)与单模通信光纤的连接损耗,并设计制作了楔形柱面光纤微透镜用来实现两者的模斑匹配,有效地降低了器件的光耦合损耗.本文介绍了楔形柱面光纤微透镜耦合的1.3 μm半导体光放大器(SOA)组件及其制作方法.该组件的最大增益不小于14 dB,其偏振灵敏度小于1 dB,增益波动不大于0.5 dB.